MAF15BKR
Fits TVs 15”- 32”
flat panel solutions
LCD TV Wall Mount
Maximum Load
Installation Manual
Capacity – 55 lb (25 kg)
CAUTION:
Thank you for choosing the RCA MAF15BKR Universal Flat Panel
TV Wall Mount. This mount can be used for all major brands of
15" - 32" flat panel TVs, 55 lbs (25 kg) or under. Before attempting
to mount your television set, please remove all parts from this
package and read the installation instructions carefully.
This wall mount is intended for
use only with the maximum
weight of 25 kg/55 bls. Use with
heavier than the maximum weights
indicated may result in instability
causing possible injury. Follow
the installation and operation
instructions carefully.
WARNING: Use of this mount with a TV weighing over 55
lbs. or with a screen larger than 32" could cause the mount
to fail causing property damage and/or personal injury.
Safety precautions
Follow these precautions to ensure safe installation and mounting of your flat panel TV.
1. Read these instructions carefully before you begin.
If you are unsure of any part of the process, contact
a professional contractor or installer for assistance.
Improper installation can result in injury or damage.
5. For drywall installation, it is essential for the
wall mount plate to be attached to wall studs.
(Use a stud finder.)
6. Use the included hardware for mounting purposes.
This hardware has been provided to ensure a safe
and secure mount.
2. The wall or mounting surface must be capable of
supporting the combined weight of the mount and
the display; if not, the structure must be reinforced.
7. Hire a licensed electrician to relocate an electrical
3. Safety gear and proper tools must be used. Failure
to do so can result in injury and/or damage. A
minimum of two people are required for installation.
Do not attempt to install this mount alone under any
circumstances.
outlet, if needed.
8. Be sure to purchase wires long enough to connect
the TV to the audio and video components in your
installation.
Keep your sales receipt to obtain warranty parts and
service and for proof of purchase. Attach it here and
record the model number. This number is located on
the product.
4. Follow all instructions and recommendations
regarding adequate ventilation and suitable
locations for mounting your display. Consult the
owner‘s manual for your particular display for more
information.
Model No. _____________________________________
Purchase Date: _________________________________
Dealer/Address/Phone __________________________
Preparing to install
Before beginning the installation process, verify that you have all the necessary tools on hand. The following
tools are required for proper installation:
Tools
Package Contents
Wall Plate (x1)
Pour des instructions
en français, se
Phillips Head Screwdriver
reporter à la page 4.
Ratchet or Driver with 13 mm (1/2”) Socket
Electric or Portable Drill
Mount Arm (x2)
Safety Bar (x1)
Para obtener
instrucciones en
español, consulte la
página 7.
3/16” (4.8 mm) Drill Bit and Stud Finder for Drywall
Installation
Instruction Manual (x1)
Hardware Kit (x1)
3/8” (10 mm) Masonry Bit for Concrete Installation
Continues on next page...
Attaching the Arms to the TV
IMPORTANT! Use extra
care during this part of the
installation. If possible, avoid
placing your display facedown
as it may damage the viewing
surface.
2. Determine the correct diameter of screw to use by
carefully trying one of each size (M4 and M6) from
the hardware kit. Do not force any of the screws
– if you feel resistance stop immediately and try a
smaller diameter screw.
3. Attach the mount arms to the back of your display
using the M6 washers (I) and the screws identified
in Steps 1 and 2 (see Fig.3)
NOTE: This mount comes
with a selection of different
screw diameters and lengths
to accommodate a wide
variety of display models. Not
all of the hardware in the kit
If you are using the longer screws on a display with
a curved or recessed back, you will also need to use
the spacers (E). You should only use a spacer if
necessary.
Fig.2
will be used.
Make sure the screws are snug, but do not
overtighten.
1. Determine the correct length of screw to use by
examining the back of your display:
For displays with
flat backs.
For displays with curved or
recessed backs.
A. If the back of your display is flat and the
mounting holes are flush with the surface, you
will use the shorter screws (A or C) from the
hardware kit.
B. If the back of your display is curved, has
a protrusion, or if the mounting holes are
recessed, you will need to use the longer screws
(B or D) and spacers (E).
Fig.3
Final Installation
1. With the help of another person, carefully lift your
display and place it on the wall plate. Do not
release the display until the mount arms have
securely hooked onto the wall plate.
2. Insert the safety bar
at the bottom of the
mount to prevent the
display from being
lifted from the wall
Fig.4
plate. A padlock can
be inserted into the
end of the bar to help
prevent theft of your
display (see Fig.5).
Fig.5
IMPORTANT! The safety bar must be used at all
times to prevent the display from being accidentally
knocked from the mount.
Periodically clean your mount with a dry cloth. Inspect all screws and hardware at regular intervals to ensure
that no connections have become loose over time. Re-tighten as necessary.
Specifications
Universal VESA Mounting Pattern: 230 mm x 250 mm
(9” x 9.8“) max
Display Size:
15” to 32”
Maximum Load:
25 kg (55 lbs)
Profile:
2.2 cm (0.9”)
3
© 2010 Audiovox Accessories Corporation
Trademark(s) Registered, Marques Déposées, Marcas Registradas.
All other brands and product names are trademarks or registered trademarks of their respective owners. /
Toutes les autres marques et tous les autres noms de produits sont des marques de commerce ou des marques
de commerce déposées de leurs propriétaires respectifs. / Todas las demás marcas y nombres de productos
son marcas comerciales o marcas comerciales registradas de sus respectivos dueños.
MAF15BKR_US_IB_02
|