Audiovox Automobile Alarm APS 596 User Manual

Model APS-596  
Owner’s Manual  
4 Button Remote Security System  
with Dual Stage Shock Sensor  
IMPORTANT ! In order to provide the highest possible level of security to your vehicle, this  
system is equipped with selectable manual override circuitry. It is possible that you will need  
to manually override your security system if the transmitter becomes lost, or inoperative due  
to battery failure. Reading the sections on "MANUALLY OVERRIDING YOUR SYSTEM" is  
necessary to fully understand the procedure required to enable your vehicle in such  
situations. In addition, the chart on the last page of this manual has a section for the particular  
features and options installed in your vehicle as well as the override method selected.  
Valet Switch manual override is pre-selected from the factory, however, the system  
can be configured for "Custom Code" operation. Confirm the override mode selected on the  
last page of this manual, and familiarize yourself with the selection on it's operation.  
FEATURES :  
! 1 Four Button Programmable RF Transmitters  
! 1 Five Button Programmable Transceiver  
! Five Channel Receiver (Capable Of Accepting Up To 4 Transmitters)  
! Code Hopping Technology  
! Selectable Manual Override Mode  
! Remote Panic in all modes  
! Protected Valet  
! User Programmable Manual Override Code  
! 7 Function LED (Light Emitting Diode) - Arm / Disarm / Zone 1, 2, 3 / Valet / Arming  
! Intrusion Alert with Memory  
! Audible Arm / Disarm / Defective Zone / Tamper Confirmation  
! Instant Siren Activation  
! Starter Disable  
! Additional Engine Immobilizer Output (optional relay required)  
! True Last Door Arming (hardwire only)  
! Defective Zone By-Pass  
! Hardwire or Voltage Sense Selectable  
! Active or Passive Arming Selectable  
! Programmable Auto Lock On / Off  
! Programmable Auto Unlock On / Off  
! Programmable Door Lock Pulse Duration 1 Second / 3.5 Seconds/1 Sec L/ Dbl. U/L  
! Programmable Active or Passive Door Locks  
! User Programmable Permanent Chirp Delete  
! On Command RF Chirp Delete from Transmitter  
! 6 Tone Multi Tone Siren  
! RF Inhibit with ignition on  
! Parking Light Flasher  
! Plug In Dual Stage Shock Sensor  
OPTIONS:  
! Remote Trunk Release ( must have electronic trunk release )  
! Remote Keyless Entry ( must have power door locks )  
! Multiple Vehicle Capable  
! Remote Starter  
! Remote Power Window Roll Up  
! Remote Garage Door Interface  
! Two Step Unlock Configurable  
! Headlight Illumination During Arming, Disarming, Or Both  
128-7131  
1 of 16  
 
entry point after the learned delay expired. Closing the hood, trunk, or doors will  
correct the problem and you do not need to disarm the system to make the correc-  
tion.  
# Doors Lock - Optional  
# Headlight Illumination - Optional  
ARMING THE SYSTEM - PASSIVE (AUTOMATIC )  
1. Turn off the engine, exit the vehicle, and close and lock all doors, hood lid  
and trunk lid.  
" Dash mounted LED begins to flash rapidly, indicating 30 second  
passive arming has begun.  
2. Opening any protected entry point during the 30 second passive arming  
cycle will immediately suspend automatic arming and the 30 second  
passive arming cycle will restart when all doors are closed. At the end of the  
passive arming cycle;  
" Dash mounted LED begins to flash slowly.  
" Parking Lights flash one time.  
" Siren sounds one chirp  
If the siren did not sound when arming, then the chirps have  
been turned off, and you should refer to the section titled  
"ELIMINATING THE ARM / DISARM CHIRPS" in this manual.  
# Doors Lock - Optional  
Door locking during passive arming is a selectable feature.  
The alarm can be programmed to allow the doors to lock only  
when arming using the keychain transmitter and they will not  
automatically lock during passive arming.  
PROTECTION WHILE THE SYSTEM IS ARMED  
" Opening any protected door, hood, or trunk lid will cause the alarm to  
immediately sound. The alarm will continue to sound for 30 seconds,  
then stop and continue to monitor all protected entry points. If the thief  
left a door opened, the alarm will sound for six 30 second cycles,  
remain armed and ignore that triggered zone.  
" Whenever the system is armed, the dash mounted LED indicator will  
slowly flash. This serves as a visual deterrent to the potential thief.  
The LED is a very low current bulb and will not cause the vehicle’s  
battery to drain, even when left unattended for extended periods.  
" Whenever the system is triggered, the vehicle’s parking lights will  
flash for the full 30 second alarm cycle, attracting visual attention to  
the vehicle.  
" Optional - Whenever the system is armed, the vehicle’s starting circuit  
will be bypassed. If the thief should choose to ignore the siren, the  
vehicle can not be started.  
" Any mild impact to the vehicle’s glass will cause the alarm to sound a  
short series of warning tones.  
" Any strong impact to the vehicle’s glass will cause the alarm to trigger  
for the full 30 second alarm cycle.  
3
128-7131  
3 of 16  
 
DISARMING THE SYSTEM  
As you approach the vehicle, press and release the Unlock button on the keychain  
Transmitter.  
" Dash mounted LED turns off.  
If passive arming was selected during the installation, then the LED  
will start flashing rapidly, indicating that the system is re-arming auto-  
matically. Open any door to suspend the automatic arming.  
" Parking Lights flash two times.  
If the parking lights flashed three times, then the alarm was trig-  
gered in your absence. Before turning the key on, examine the LED to  
identify which zone was triggered.  
" Siren sounds two chirps.  
If the siren sounds 4 chirps, then the alarm was triggered in your  
absence. Before turning the key on, examine the LED and refer to the  
INTRUSION WARNING SIGNALS section of this manual to identify  
which zone was triggered.  
If the siren did not sound when disarming, then the chirps have  
been turned off, and you should refer to the section titled “ELIMI-  
NATING THE ARM / DISARM CHIRPS“ in this manual.  
# Doors Unlock - Optional  
Note: If the optional 2 step door unlock circuit is installed, when the unlock  
transmitter button is activated, the drivers door only will unlock, pressing  
the unlock button a second time will cause all doors to unlock. If your  
transmitter has a separate lock unlock buttons, pressing the unlock button  
anytime after the first unlock command will cause all the vehicle doors to  
unlock.  
# Headlight Illumination - Optional  
SILENT DISARMING  
As you approach the vehicle, press and hold the Unlock button on the keychain  
transmitter for 2 seconds.  
" Dash mounted LED turns off.  
If passive arming was selected during the installation, then the LED will  
start flashing rapidly, indicating that the system is re-arming automatically.  
Open any door to suspend the automatic arming.  
" Parking Lights flash two times.  
If the parking lights flashed three times, then the alarm was triggered in  
your absence. Before turning the key on, examine the LED to identify which  
zone was triggered.  
" Siren will not sound.  
If the siren sounds 4 chirps, then the alarm was triggered in your absence.  
Before turning the key on, examine the LED and refer to the INTRUSION  
WARNING SIGNALS section of this manual to identify which zone was trig-  
gered.  
# Doors Unlock - Optional  
Note:If the optional 2 step door unlock circuit is installed, when the unlock  
transmitter button is activated, the drivers door only will unlock, pressing  
the unlock button a second time will cause all doors to unlock. If your  
4
128-7131  
4 of 16  
 
transmitter has a separate lock/unlock buttons, pressing the unlock  
button anytime after the first unlock command will cause all the vehicle  
doors to unlock.  
# Headlight Illumination - Optional  
WHILE THE SYSTEM IS SOUNDING  
If during a triggered state, you wish to shut off the siren without disarming your  
security system, simply press and release any transmitter button other than the  
disarm button. This action will turn off the siren yet leave the vehicle fully armed  
and protected. This feature is particularly useful if you are aware of children play-  
ing near your vehicle that may accidently trigger your security system. In this case  
you can cancel the siren sounding without disarming your alarm.  
INTRUSION WARNING SIGNALS  
This system will inform you if an intrusion attempt has occurred while you were  
away from the vehicle. If an intrusion attempt has occurred, the siren will chirp 4  
times and the parking lights will flash 3 times when disarming the system. Enter  
the vehicle and observe the dash mounted LED to identify which zone was trig-  
gered.  
$ If the LED is flashing one time...pause...one time...pause...etc., then an  
intrusion attempt was made to the shock sensor, or an accessory  
triggering device that may have been added to the system.  
% If the LED is flashing two times...pause...two times...pause...etc., then  
an intrusion attempt was made to a hood or trunk pin switch that was  
added to the system, or to a light activated entry point if the alarm was  
installed using the voltage sensing feature.  
& If the LED is flashing three times...pause...three times...pause...etc.,  
then an intrusion attempt was made through one of the vehicle’s doors.  
These intrusion warning indicators are stored in the system’s memory and will  
only be erased when the ignition key is turned on.  
VALET SWITCH  
The valet switch allows you to temporarily bypass all alarm functions, eliminating  
the need to hand your transmitter to parking attendants or garage mechanics.  
When the system is in valet mode, all alarm functions are bypassed, however the  
remote panic feature and remote door locks will remain operational. To use the  
valet mode, the system must first be disarmed either by using your keychain  
transmitter, or by operating the manual override sequence.  
1. From the disarmed condition, turn the ignition key to the on position.  
2. Press and hold the valet pushbutton switch until the dash mounted LED,  
turns on. The LED will remain on as long as the system is in valet mode.  
3. To return to normal operation, press and release the push button switch any  
time the ignition is on.  
Note: Always remember to return the system to the NON VALET mode, after  
servicing, to ensure that the vehicle remains protected at all times.  
5
128-7131  
5 of 16  
 
MANUALLYOVERRIDINGYOUR SYSTEM:  
USING THE VALET SWITCH MANUAL OVERRIDE  
Your Security System can be disarmed without the use of the keychain transmitter.  
This is necessary, since you will need the ability to operate your vehicle if the  
transmitter is lost or its battery fails. If your system has been selected for Valet  
Switch manual override as indicated on the last page of this manual, to bypass the  
alarm system.  
1. Open the vehicle door. The alarm will sound.  
2. Turn the ignition key to the on position.  
3. Within 5 seconds, press and release the valet push button switch.  
The alarm system will stop sounding and enter the disarmed mode. You can now  
start and operate the vehicle normally.  
Typically this override mode is used only if the transmitter has become inoperative.  
You may elect to enter the VALET mode until repair or replacement of the transmitter,  
after which, returning the system to the full operation mode is necessary. To do so,  
see item 3 under the heading VALET SWITCH.  
Programming Your Custom Override Code:  
Unlike override switches easily found, and defeated, this security system allows  
the consumer to program a personal override code, offering a higher level of  
security. To take advantage of this option, programmable feature # 10 must be  
selected for the Custom Code Option. Consult your installation center for  
programming details. The system comes from the factory with a pre-programmed  
override code of 11. To change this default override code, do the following:  
1.Disarm the system by use of the transmitter, or by use of the emergency  
override sequence. Turn the ignition switch to the on position.  
2. Within 10 seconds, press and release the valet/override switch, 3 times.  
3. Within 10 seconds turn the ignition switch off, on, off, on, off, on.  
(The siren or horn will beep and the lights will flash one time.)  
4. Within 10 seconds, begin to enter your chosen 10ths digit by pressing and  
releasing the pushbutton switch from 1 up to 9 times.  
5. Within 10 seconds of the last entered 10ths digit, turn the ignition switch off  
then on.  
6. Within 10 seconds, begin to enter your chosen units digit by pressing and  
releasing the pushbutton switch from 1 up to 9 times.  
7. Finish by turning the ignition switch to the off position.  
If the new code was accepted, the unit will report back the newly entered code, by  
flashing the LED, first indicating the 10ths digit, pause and then the units digit.  
The unit will report the new code three times with a one second pause between  
each code, then the system will begin arming. If the LED flash pattern reports the  
previously stored code, the new code was not entered correctly. Please repeat  
steps 1 through 7 above considering the following.  
Note:  
Acceptable digits 10ths or units are 1 through 9. The unit will not recog-  
nize a 0 (Zero), or no digit entered in any place, units or tenths.  
If 15 seconds of inactivity expire, or if the ignition switch is turned off for  
more then 5 seconds during any of the above steps, the unit will revert  
back to the last successfully stored code.  
Note:  
6
128-7131  
6 of 16  
 
Custom Code Programming Example:  
To Change the code from the factory pre-assigned code of 11 to “52” you would do  
the following:  
1. Disarm the system by use of the transmitter, or by use of the emergency  
override sequence.  
2. Turn the ignition switch to the on position.  
3. Within 10 seconds, press and release the valet/override switch, 3 times.  
4. Within 10 seconds turn the ignition switch off, on, off, on, off, on.  
(The siren or horn will beep and the lights will flash one time.)  
5. Within 10 seconds, begin to press and release the push button switch to set  
the tenths digit.  
(As per the example, press and release 5 times to set the tenths digit to 5)  
6. Within 10 seconds of the last press of the pushbutton, turn the ignition switch  
off then on.  
7. Within 10 seconds, begin to press and release the push button switch to set  
the units digit.  
(As per the example, press and release 2 times to set the units digit to 2).  
8. Turn the ignition switch to the off position. Immediately observe the LED flash  
pattern.  
You will note the LED flashing five times, pause, and then flash two times, pause.  
This pattern will be repeated three times indicating the new code (52) has been  
accepted and stored in memory.  
Note: If after step 8, the LED flashes a code other than what was just entered,  
this indicates that the code has not been changed. You will have to repeat  
steps 1 through 7 above being certain to note the following:  
Acceptable digits 10ths or units are 1 through 9. The unit will not recognize a 0  
(Zero), or no digit entered in any place, units or tenths.  
Note: If 15 seconds of inactivity expire, or if the ignition switch is turned off for  
more then 5 seconds during any of the above steps, the unit will revert back  
to the last successfully stored code.  
MANUALLYOVERRIDINGYOUR SYSTEM:  
USING THE CUSTOM CODE OVERRIDE  
Assuming the override code programmed has not been changed, and the default  
override code of 11 is in the system's memory.  
1. Enter the vehicle and turn the ignition switch to the on position.  
Note: The siren will sound.  
2. Within 5 seconds, press and release the pushbutton switch 1 time.  
3. Within 5 seconds, turn the ignition switch off then on.  
4. Within 5 seconds, press and release the pushbutton switch 1 time.  
5. Turn the ignition switch off then on and start the vehicle.  
Note: If you have changed the programmed override code then substitute your  
new code tenths for step 2 above, and units for step 5 above.  
ELIMINATING THE NORMALARM / DISARM CHIRPS  
As explained earlier in the manual, you can eliminate the chirps selectively any  
time you arm or disarm the system simply by holding the ARM / DISARM button for  
two seconds. If you find the normal arming and disarming chirps annoying, they  
7
128-7131  
7 of 16  
 
can be turned off permanently, eliminating the need to hold theARM / DISARM button  
for two seconds. To do this,  
1. Turn the ignition key on then off.  
2. Within 10 seconds, press and release the valet push button switch three  
times.  
3. If the chirps were on before you started, then you will hear 2 chirps indicating  
they have been turned off.  
If the chirps were off before you started, then you will hear one chirp indicating they  
have been turned on.  
Note: Whenever the chirps are bypassed, the 4 chirp intrusion indicator and 3  
chirp defective zone indicator will always operate. Since these are important  
warnings to you that something has happened, they cannot be eliminated.  
REMOTE PANIC OPERATION  
The ARM or DISARM button on your keychain transmitter also functions as a panic  
switch for use in emergency situations. To use remote panic,  
1. Press and hold the ARM or DISARM button on the keychain transmitter for 3 or  
more seconds. The alarm will immediately sound.  
2. To stop the alarm, press and hold the ARM or DISARM button on the transmitter  
again for 3 seconds. If the button is not pressed, the alarm will automatically  
stop after 30 seconds. Also if any transmitter button other than the ARM or  
DISARM button is pressed and released, the Panic mode will be turned off  
immediately. The normal function of this transmitter button will be suspended  
during the Panic sounding period.  
3. During the panic mode, the Lock and Unlock buttons can be used to lock and  
unlock the doors, (if the option is installed), however once the unlock/disarm  
button is pressed, the vehicle's starter inhibit device, (where installed) will be  
disabled allowing the vehicle to start.  
Note: While in the Panic mode, pressing and releasing the ARM or DISARM  
buttons will, if the option is installed, lock and unlock the doors respectively.  
While in the panic mode, anytime the DISARM button is pressed, the panic  
feature will continue for the allotted 30 seconds, however, the security  
system will be disarmed allowing the vehicle to start.  
ADDITIONAL REMOTE FUNCTION ( CHANNEL 3 )  
This security system has an additional features that can be connected to a number  
of different optional accessories. Some of the more common uses for this channel  
are;  
# Remote Trunk Release  
# Remote Window Closure  
# Remote Car Starter  
# Remote Garage Door Interface  
Operation of the optional accessory or accessories, can be controlled by pressing  
and holding the programmed button on the keychain transmitter for four seconds,  
or by pressing and releasing the programmed button on the transmitter two times  
in succession. Check with your installation center for more information on what  
accessories were installed and how they are accessed.  
8
128-7131  
8 of 16  
 
ADDITIONAL REMOTE FUNCTION ( CHANNEL 4 )  
This security system has an additional feature that can be connected to a number  
of different optional accessories. Some of the more common uses for this channel  
are:  
# Remote Trunk Release  
# Remote Window Closure  
# Remote Car Starter  
# Remote Garage Door Interface  
To activate the optional accessory, press the programmed button on the keychain  
transmitter for up to 8 seconds for continuous output, or press and release for  
momentary activation. The optional accessory will immediately engage. Check  
with your installation center for more information on the optional accessory that  
may have been installed and how it is accessed.  
ADDITIONAL REMOTE FUNCTION ( CHANNEL 5 )  
This security system has an additional feature that can be connected to a number  
of different optional accessories. Some of the more common uses for this channel  
are;  
# Remote Trunk Release  
# Remote Window Closure  
# Remote Car Starter  
# Remote Garage Door Interface  
To activate the optional accessory, press the programmed button on the keychain  
transmitter for up to 8 seconds for continuous output, or press and release for  
momentary activation. The optional accessory will immediately engage. Check  
with your installation center for more information on the optional accessory that  
may have been installed and how it is accessed.  
IGNITION CONTROLLED LOCK UNLOCK: (Unlock Drivers Only, or UnlockAll Doors)  
Your security system has a selectable safety feature that allows the vehicle doors  
to lock when the ignition switch is turned on, (Providing all doors are closed), and  
to unlock the doors when the ignition switch is turned off. In addition, the unlocking  
of the doors is further selectable, in a two step unlock configuration, to unlock only  
the drivers door or all doors.  
TELEMATICUPGRADE:  
This system has the ability to have a telematic upgrade module connected to it.  
This is a upgrade that can give you control of certain functions of your vehicle from  
a Telephone, or in some cases a computer interface. Please check with your  
installation center for most recent Telematic Upgrades. If you had a Telematic  
Upgrade installed, the manual supplied with the upgrade unit will provide a op-  
erators manual advising of the features of the system and means available to  
control these features of your vehicle.  
9
128-7131  
9 of 16  
 
Included with your system is a two way remote transceiver that makes use of a  
LCD screen to indicate certain that the vehicle reacted to commands that you  
executed from the hand held transmitter(s). Shown below are these screens  
for reference.  
When Disarmed, Press the Arm/Lock button  
to Lock and Arm the System. The Lock Icon  
is displayed on the LCD panel & the parking  
lights flash once.  
When Armed, Press the Disarm/Unlock but-  
ton to Unlock and Disarm the System. The  
Unlock Icon is displayed on the LCD panel &  
the parking lights flash twice.  
When the Key Icon Button Has Been Oper-  
ated for 3 seconds the trunk open icon will  
flash on the LED Screen.  
When the Key Icon Button is pressed 2 times  
in succession The three puffs of smoke  
show on the LCD screen for 2 seconds indi-  
cating that the vehicle received and acted  
upon the RF command.  
When Panic Mode has been activated and  
the system is armed the vehicle's lights, the  
lock and the siren icon will flash on the LCD  
screen. If the system is disarmed and the  
Panic Mode is activated, the lights, s i r e n ,  
and the unlock icons will flash on the LCD  
screen.  
When ever the vehicle is operated from the  
two way transmitter, the unit will beep  
responsive to the function executed at the  
vehicle. 1 beep when armed, 2 beeps  
when disarmed, etc... at times It may be  
inconvenient or too noisy to hear the beep  
tones, so the system allows you to set the  
unit for vibrate mode. To toggle on or off  
beep tones/vibrate, press the F & Unlock  
buttons, the unit will beep or vibrate, and  
the icons shown left will appear on the  
screen.  
10  
128-7131  
10 of 16  
 
If the alarm system has been triggered, the  
icon displayed on the transmitter LCD will in-  
dicate which zone has been activated, as well  
sound the beep tones, or vibrate dependent  
upon the setting as shown above. The fol-  
lowing trigger patterns will be displayed.  
Triggered and the entry attempt was made to  
one of the vehicle doors.  
Triggered and entry attempt was made to the  
vehicles hood or trunk.  
Triggered and entry attempt was made to the  
vehicles glass, or the vehicle has been hit or  
bumped hard enough to cause a response  
from the vibration detector.  
ADDITIONAL ICONS THAT MAY BE DIS-  
PLAYEDARE:  
If the arm/disarm chirp tones have been  
turned off at the vehicle, when you arm, or  
disarm, the display will indicate this as shown  
and there will be no arm/disarm chirps at the  
transmitter. This is true if the transmitter is  
set for vibrate mode.  
When the vehicle is armed, and a door is  
opened, or ajar, the transmitter will chirp 3  
times, the lights will flash, and then the dis-  
play will flash as shown. When the door is  
closed or the zone clears, the transmitter will  
chirp 1 time, and the display will clear.  
When the vehicle is armed, and the hood or  
trunk, is opened or ajar, the transmitter will  
chirp 3 times, the lights will flash, and then  
the display will flash as shown. When the  
hood or trunk is closed, or the zone clears,  
the transmitter will chirp 1 time, and the dis-  
play will clear.  
11  
128-7131  
11 of 16  
 
When the vehicle is armed, and the vibration  
sensor input is active, the transmitter will chirp  
3 times, the lights will flash, and then the dis-  
play will flash as shown. When the input or  
the zone clears, the transmitter will chirp 1  
time, and the display will clear.  
The Battery Icon Indicator will show 3 bars as shown left, when the  
battery is at full capacity and will show less than 3 bars as the battery  
deteriorates. This is a guide and should be used to monitor the  
condition of the battery. The battery should require replacement  
approximately every 6 months.  
If someone at the vehicle pages you by using the Valet/Push-Button  
Switch from within the vehicle, the Call Icon shown left will turn on and  
the hand held transmitter will beep or vibrate based on the units  
programming.  
Check Vehicle Status:  
Press the lock+key+option buttons simultaneously for 1 second. The vehicle's  
alarm will display the systems current status.  
Vibrate Or Tones:  
Press the "F"+Unlock buttons simultaneously for 1 second. The transmitter will  
vibrate if vibrate is on or beep if tones are turned on. Pressing this button  
combination again will toggle this feature on or off.  
Page Call Out:  
From within the vehicle, if the valet push button is pressed for three seconds,  
the alarm unit in the vehicle will transmit to the LCD remote and a beep tone  
will be heard on the hand held transmitter indicating that someone is calling  
you to the vehicle.  
Timing Count Down:  
The unit offers an additional count down timer for situations where an alert tone  
may be needed to remind you of something important. For instance you may  
have a meeting 4 hours from now and you want a reminder in 3 Hrs and 45  
Mins. This additional count down timer allows you to set the count down up 19  
Hours and 59 Minutes from the current time and when the timer reaches zero,  
the transmitter will emit a tone or vibrate dependent on your preferred setting.  
See chart for setting the count down time for this feature.  
Valet:  
When the System is in the valet mode, the  
icon shown will show in the  
display when the status check buttons are activated.  
12  
128-7131  
12 of 16  
 
Parking Meter Counter:  
The transmitter has a built in clock that can count down from 10, 20, 30, 60, 90,  
or 120 minutes. This feature is useful when parking the vehicle in a metered  
parking lot. If the time on the parking meter is 30 minutes, you can set the count  
down timer to 20 minutes. The transmitter will emit a beep tone when the timer  
expires to remind you to get back to your vehicle. See following chart for setting  
the parking meter count down timer feature.  
Alarm Clock Mode:  
The transmitter has a built in alarm clock that can be set to beep at a certain  
time each day. The alarm clock mode must be set, and the feature turned on.  
To use this feature please refer to the chart on the following page.  
Note:  
While in the two way transmitter set up mode, 15 seconds of inactivity,  
or pressing the "F" button for 5 seconds, will cause the set up mode to  
be exited.  
Note:  
Remote Start Melody select, and Temperature Check is available only  
with some self container remote start models.  
13  
128-7131  
13 of 16  
 
14  
128-7131  
14 of 16  
 
APS-596  
SYSTEM FUNCTIONSATAGLANCE  
DASH LED INDICATORS  
RAPID FLASHING  
=
=
=
=
=
=
=
PASSIVEARMING  
ARMED  
SLOW FLASHING  
OFF  
ON SOLID  
DISARMED  
VALET MODE  
3 FLASH...PAUSE  
2 FLASH...PAUSE  
1 FLASH...PAUSE  
INTRUSION ZONE 3  
INTRUSION ZONE 2  
INTRUSION ZONE 1  
SIREN CHIRPINDICATORS  
*1CHIRP  
*2CHIRPS  
3 CHIRPS  
4 CHIRPS  
=
=
=
=
ARM  
DISARM  
ARM / DOOR OPENED  
DISARM / INTRUSION  
* These chirps are optional, and can be de - activated.  
PARKING LAMP INDICATORS  
1 FLASH  
=
=
=
ARM  
2 FLASHES  
3 FLASHES  
DISARM  
DISARM / INTRUSION  
Your System Has These Features Activated  
# Starter Disable  
# Remote Keyless Entry  
# Auto Lock with ignition key  
# Auto Unlock with ignition key  
# Passive Arming  
# No Lock in passive mode  
# Hardwire doors, hood, and trunk  
# Custom Code Override  
# Valet Switch Override  
15  
128-7131  
15 of 16  
 
© 2004 Audiovox Electronic Corporation, 150 Marcus Blvd., Hauppauge, N.Y. 11788  
128-7131  
16  
128-7131  
16 of 16  
 

Actiontec electronic Network Router 0530 0276 000 User Manual
ADC Network Router Dual Inline TMAs User Manual
ADIC Tool Storage Version 27 User Manual
ADTRAN Network Card NT1 ACE User Manual
AEG Power Supply PROTECT A User Manual
Aiwa CD Player EV600B User Manual
Allied Telesis Network Card AT 2750FX User Manual
BC Speakers Speaker 10PLB76 User Manual
BC Speakers Speaker 12PS76 User Manual
Behringer Music Mixer BXR1800H User Manual