Preparing to Connect My Multifunction
To My Network
Network Requirements
Before connecting the machine to the network, make sure that configuration of the computer and access point or router is
complete, and that the computer is connected to the network.
Wireless Connection
Before connecting the machine to the network, the computer needs to be connected to the network. Make sure that
configuration of the computer and access point or router is complete.
3
Preparing to Connect My Multifunction
To My Network
An "Ad-hoc connection," which establishes a direct wireless connection between
the computer and printer without using an access point, is not supported.
A router or access point is required for your printer to be used on a wireless
network.
Notes on Network Connection
• The configuration, router functions, setup procedures and security settings of
the network device vary depending on your system environment. For details,
refer to your device's instruction manual or contact its manufacturer.
• In an office setup, consult your network administrator
• If you connect to a network that is not protected with security measures, there
is a risk of disclosing data such as your personal information to a third party.
• If an error message appears or if you have trouble with the network
connection, refer to the printed manual: Network Setup Troubleshooting.
• Place the machine and computer on the same network segment.
4
Installing the Drivers & Software
Software Installation
To use the machine by connecting it to a computer, software including the drivers needs to be copied (installed) to the computer's hard disk. The
installation process takes about 20 minutes. (The installation time varies depending on the computer environment or the number of application
software to be installed.)
IMPORTANT
• Log on as the administrator (or a member of the Administrators group).
• Quit all running applications before installation.
• Do not switch users during the installation process.
• Internet connection may be required during the installation. Connection fees may apply. Consult the internet service provider.
• It may be necessary to restart your computer during the installation process. Follow the on-screen instructions and do not remove the
Setup CD-ROM during restarting. The installation resumes once your computer has restarted.
• If the firewall function of your security software is turned on, a warning message may appear that Canon software is attempting to access
the network. If such a warning message appears, set the security software to always allow access.
5
Installing the Drivers & Software
Installing the PIXMA MG3120 on Your Wireless Network
If you are installing your printer on your network for the first time, a step-by-step walk through of the wireless setup is built in to the installation
routine of the software that shipped with your PIXMA.
*Insert the Setup CD-ROM that came with your printer into your CD-ROM drive and proceed through the easy to follow instructions.
*If you don’t have or cannot use the Setup CD-ROM, you can still install the printer using a downloaded file. Click here for information.
Be sure to select Wireless Connection on the Connection Method Selection screen (1-2).
Continue carefully following the Printer Setup instructions (Steps 2-1 through 2-3) until the Setup Procedure Selection screen (3-1)
appears. This is shown on the next page.
6
Installing the Drivers & Software
On the Setup Procedure Selection screen (3-1) screen, select Wireless Setup Using the USB Cable. This is the recommended setup method.
You will need to use the supplied USB cable
Continue to follow any on-screen instructions until the Software Installation List appears. This screen is shown on the next page
7
Installing the Drivers & Software
On the Software Installation List select any additional* software to install and click Next.
*MP Drivers is required for installation and cannot be deselected. In addition, we recommend installing MP Navigator EX and Easy-
PhotoPrint EX in order to take full advantage of your printer’s features.
*If you are using the downloaded ‘Mini Master setup’ file to install the printer, only the MP Drivers will be installed. Additional software
can be downloaded separately. The software can be found in the Software section of Drivers & Software (the same page where you
downloaded the Mini Master setup file)
8
Installing the Drivers & Software
The drivers and software will install. Continue to follow the on-screen instructions.
Click Next on the Set Up New Printer window, then connect the supplied USB cable between the printer and computer and click Next
on the Connect Cable screen..
9
Installing the Drivers & Software
If the Access Points screen appears:
Select the Access Point to connect to, enter the Network Key (password) and click Connect.
*For details on how to check the Access Point name/network name (SSID) and network key, refer to the manual supplied
with your access point or contact its manufacturer.
10
Installing the Drivers & Software
If the Confirm Connection Access Point screen appears:
Click Yes to confirm the Access Point .
11
Installing the Drivers & Software
Disconnect the USB cable when the Disconnect Cable screen appears. Click Next
Setup is now complete. Follow any remaining instructions to exit the setup program.
12
Installing the Drivers & Software
Installing the PIXMA MG3120 on Your Wireless Network
If you can’t find your CD-ROM, you may download the MG3100 series Mini Master Setup, which includes the same step-by-step installation as
the CD-ROM, by following the instructions below:
2. Select the operating system of your computer in the dropdown lists (see example below).
3. Expand the ‘Drivers’ section, if necessary, by clicking the red triangle.
4. Click on the ‘MG3100 series Mini Master Setup’ entry.
5. After reading the license agreement, click ‘I Agree – Begin Download’ and save the file to your computer.
6. Once the download is complete, double-click the file from its download location to begin the installation.
7. Follow the same instructions as you would if using the Setup CD-ROM. Click here to go to instructions.
13
|