Chrysler Automobile Alarm CHDL3 User Manual

Installation  
Manual (1\2 Pages)  
Platform #03  
Firmware: CHDL7  
Description: Chrysler Dodge Jeep Door Lock Alarm Interface (NO KEY REQUIRED)  
Functions: Data Bus Interface: Lock/Unlock, Trunk/Rear Hatch, OEM Security Arm/Disarm, Starter Enable, Door Sense Trigger  
Downloadable Firmware for Platform #03: CHDL7,JDL,CHDL6+,CHDL2, CHDL3, CHDL4  
for the firmware that is flashed to the platform you are using.  
See Wire Connection Guide for detailed information regarding wire functionality  
Section A  
Internet  
USB Adaptor  
.
C
.
P
Option A  
USB Ca ble  
Firmware Upgrades  
4 PIN DATA TO DATA (D2D) CABLE (OPTIONAL ACCESSORY)  
“B” Requires ClearCode Vehicle Interface Protocol  
Option B Data 2 Data connection with RCS  
*Activation Input (See Note)*  
UUPPGGRRADEAABBLLEE  
DOOR LOCK  
IINNTTERFAACCEE  
MODULE  
(-)  
INPUT  
Brown  
(-)  
(-)  
(-)  
INPUT  
INPUT  
OUTPUT  
Green  
Lock  
Unlock  
Blue  
Violet/White  
MUX (2nd Start) (See Wire Guide)  
Data  
DATA  
Violet  
(-)  
(+)  
(-)  
Pink/White  
Pink  
OUT  
Door Sense Trigger  
Start Input  
INPUT  
INPUT  
INPUT  
Orange  
Trunk Input  
(+)  
(+)12 Volt Constant  
Red  
LED  
(-)  
INPUT  
Black  
Chassis Ground  
PIN  
6
Programming  
button  
1
8
Connect to Brown wire from bypass module.  
*NOTE: If the remote control system  
does not have an activation output  
that turns on at exactly the same time  
as the 1st ignition, then add relay and  
install as per Fig.2. Most remote  
systems GWR or (-) 3rd ign. outputs  
turn on before the main ignition and  
will cause diagnostic codes.  
“Fig. 1”  
87  
Connect to  
ignition (+) wire  
of remote  
GWR from  
remote starter  
87A  
30  
85  
86  
SKIM  
MODULE  
starter  
Chassis Ground  
“Fig. 2”  
DATA  
WIRE  
Section B  
WIRE GUIDE: CONNECTIONS  
Optional D2D VIP: Data to Data Vehicle Interface Protocol will replace specific analogue connections  
10 PIN HARNESS  
(-)  
/(+)  
WIRE  
COLOR  
Connect  
Location  
D2D  
VIP  
I/O  
STATUS  
VEHICLE  
TYPE  
ACTIVATION and/or FUNCTIONALITY  
SPECIFIC WIRE CONNECTION LOCATION  
PIN#  
(-)  
Ground When Igition is Activated  
This wire must activate at the same time as main ignition.  
(See Fig.2)  
Brown  
Input  
RCS  
Factory Alarm Arm/ Disarm  
1
N/A  
(-)  
(-)  
(-)  
Lock connects to (-) Lock Output wire of RCS  
RCS  
RCS  
Lock All Doors  
2
3
4
N/A  
N/A  
N/A  
D2D Input  
Green  
Blue  
Input  
D2D  
Unlock All Doors (See User Settings)  
Unlock connects to (-) Unlock Output wire of RCS  
MUX (Violet/Brown Pin 4 of Ignition Harness)  
Violet/  
White  
Output  
2nd Start and Accessory (Resistance)  
Output to Vehicle  
Vehicle  
(See Fig. 1)  
5
6
7
N/A  
N/A  
N/A  
Data  
Vehicle White/Orange PIN#6 of 8 PIN SKIM harness in steering column  
Violet  
(-)  
Door Sense Trigger connects to (-) door trigger  
RCS  
Pink/  
White  
Detects Doors status (open/closed) via data  
bus then converts to an analogue output (-)  
Output  
Input  
D2D  
input wire of RCS  
(+)  
Pink  
RCS  
Start Output - Connection is parallel to the vehicle and remote  
control system starter wires.  
Enables 2nd Start  
(-)  
(+)  
(-)  
Trunk Output  
Trunk/Rear Hatch Release  
Power Source  
D2D Input  
Orange  
Red  
N/A  
N/A  
N/A  
RCS  
8
9
Constant (+) 12 Volt Source  
Chassis Ground  
D2D  
D2D  
Vehicle  
Vehicle  
Input  
Input  
Black  
Ground Source  
10  
Legend  
RCS = Remote Control System  
N/C = No Connection  
N/A = Not Applicable W2W= analogue wire to wire D2D= data 2 data  
DATA to DATA PORT (D2D): Blue connector of D2D Cable plugs into the upgradeable vehicle interface module.  
OPTION A: - D2D Port used to connect to USB Bootloader adaptor & computer to download & flash vehicle interface firmware.  
OPTION B: - D2D Port used to connect to the data port of a remote control system equipped with ClearCode Vehicle Interface Protocol.  
Remote control systems designed with ClearCode VIP can securely communicate via the D2D cable to transmit & receive data commands which initiate  
specific vehicle function such as doorlocks & immobilizer override and /or request information from the vehicle such as status of entry points (doors) or ambient  
température, diesel glow plug etc…ClearCode VIP represents the doorway to vehicle integration...  
This Interface kit / Data Bus Interface part has been tested on the listed vehicles. Other vehicles will be added to the select vehicle list upon completion of compatibility testing. Visit website for latest vehicle application guide. DISCLAIMER: Under no circumstances shall  
the manufacturer or the distributors of the bypass kit / data bus interface part(s) be held liable for any consequential damages sustained in connection with the part(s) installation. The manufacturer and it’s distributors will not, nor will they authorize any representative or  
any other individual to assume obligation or liability in relation to the interface kit / data bus interface part(s) other than its replacement. N.B.:Under no circumstances shall the manufacturer and distributors of this product are liable for consequential damages sustained in  
connectionwiththisproductneither assumesnor authorizesanyrepresentativeorotherperson toassumeforitanyobligationor liabilityotherthanthereplacementofthisproductonly.  
 

Black Box Computer Hardware hardened pol poe ethernet extenders User Manual
Black Box Network Hardware NBS008A User Manual
Black Decker Hot Beverage Maker JKC450 User Manual
Blomberg Oven Accessories BIO 7443 User Manual
Bosch Appliances Radio LE10 User Manual
Bosch Power Tools Power Hammer cordless hammer User Manual
Braun Mixer MR 320 User Manual
Briggs Stratton Vacuum Cleaner 5631 User Manual
Carrier Refrigerator 19XL User Manual
Casio Watch MA0804 EG User Manual