TM
LEGACY TENT
MODEL 2000001643
Fig. 2
Before you begin
Read all instructions before set up.
• Select a level site clear of rocks, branches, and other hard or sharp
objects, to install your tent.
WARNING: Keep clear of overhead power lines.
• Do not set up your tent under trees because of potential lightning
strikes or falling tree limbs in inclement weather.
• Secure with all stakes and guylines provided to prevent property
damage or personal injury.
Door
• For best results in windy conditions, position narrow end of tent into
the wind.
• Enlist the help of at least one other person to assist you when it is
time to assemble the tent.
2A
2B
Pole Descriptions
Pole
Pole
Pole
2C
Description
Qty. Dia.
Repair Kit Replacement Kit
Main Body Pole, black
Side Body Pole, grey
Rainfly Pole, black
Vertical Door Pole, black,
short w/rubber tips
2
2
1
11mm 501000539
9.5mm 501000540
11mm 501000539
6.3mm 501000543
6.3mm 501000543
501000549
501000548
501000549
Hinged, Rigid Door
1. Assemble Vertical Door Pole (shorter black pole with plastic tips);
then insert through zippered vertical pole sleeve on hinged side of
door. (Fig. 3)
2. Insert end of Vertical Door Pole into bottom hinge plate, apply
pressure to form a slight bow, then insert other tip of pole into top
hinge. Zip up vertical pole sleeve. (Fig. 4 & 5)
3. Assemble Door Pole (longer black pole with plastic cap tips); then
insert into zippered pole sleeve at top of door. (Fig. 6)
4. Insert end of Door Pole into top hinge plate, apply pressure to form
a bow, then insert other tip of pole into the bottom hinge. (Fig. 7)
5. Zip up pole sleeve to enclose Door Pole. (Fig. 8)
1
1
501000545
501000545
Door Pole, black,
long w/rubber tips
To Set Up Tent
1. Unfold tent and spread out on a clean, level surface with the
door facing the desired direction. (Fig. 1)
2. Assemble all poles by interlocking the shock-corded, sections
together.
Fig. 3
Fig. 4
Fig. 5
Vertical Pole
Sleeve
3. Insert grey Side Body Poles through the grey trimmed sleeves
on both sides of tent; then insert black Main Body Poles
through black trimmed sleeves, in center of tent, forming a
“X”. Make sure black Main Body Poles overlap the grey Side
Body Poles. (Fig. 1)
Door Hinge
Fig. 7
Fig. 6
Sleeves with Black Trim
Fig. 1
Sleeve with
Grey Trim
Top
Door
Hinge
Sleeve with
Grey Trim
Pole
Sleeve
Fig. 8
Door
To Attach Rainfly
1. Insert black Rainfly Pole with through sleeve in underside of
Front of Tent
Rainfly. (Fig. 9)
Black, Shock-corded Main Body Poles
2. Drape Rainfly over tent with Rainfly Pole centered above front door
& the dark blue vestibule flaps located in the front. (Fig 9)
Grey, Shock-corded Side Body Poles
Fig. 9
4. Insert end of each black Main Body Poles & grey Side Body
Poles into pins. (Fig. 2 & 2A)
Rainfly Sleeve
5. Go to opposite end of each pole and gradually apply pressure
to each forming arches. Insert the pin into each pole end at the
sides and corners of tent. (Fig. 2 & 2A)
6. Attach frame clips along edges of tent to the black Main Body
Poles & grey Side Body Poles. (Fig. 2B)
Rainfly
Black Rainfly
Pole
7. Stretch tent until taut, then secure metal loops located on both
sides and web loops located at four corners of tent with
stakes. (Fig. 2C)
Door
(continued on other side)
|