®
Model 139.53684
Keyless Entry
To comply with FCC rules, adjustment or modification of receiver and/or
transmitter is prohibited, except for changing the password setting and replacing
the transmitter battery. THERE ARE NO OTHER USER SERVICEABLE PARTS.
Features
For use with any SECURITY✚ compatible
garage door opener receiver.
Personalized Password: Up to 10,000
possible combinations. Password can be easily
changed if desired.
WARNING
Children operating or playing with a garage door opener can
injure themselves or others. The garage door could close and
cause serious injury or death. Do not allow children to operate the
wall push button(s) or remote control(s).
A moving garage door could injure or kill someone under it.
Activate the opener only when you can see the door clearly, it is
free of obstructions, and is properly adjusted.
Temporary password: Can be added for visitors or service
persons. This temporary password can be limited to a programmable
number of hours or a programmable number of entries.
Rolling Code: While your password remains constant until you
change it, the code between the Keyless Entry and the receiver
changes with each use, randomly accessing over 100 billion new
codes.
Operation: Opener activates when 4-digit password and Enter button
is pressed.
If wrong numbers are accidentally pressed, correction can be made
immediately. The Enter button will transmit only the last four digits.
The Keypad will blink for 15 seconds after the password is
transmitted. During that time the Enter button can be used to stop or
reverse the door travel.
The Lock feature on openers with premium door controls is designed
to prevent operation of the door from portable transmitters.
However, the door will open and close from the door control push
button and the Keyless Entry.
Installation
Keypad
The recommended
mounting locations for
Exterior Front Wall
1-Piece or
Sectional Door
sectional and one-piece
doors are shown in
Figure 3. You can select
another location if you
prefer. However, the
keypad must be
Door Jamb Edge
(Optional Location
for 1-Piece Door)
Door Jamb Face
SECTIONAL DOOR ONLY
installed within sight of
the door.
KEYPAD MUST BE INSTALLED
WITHIN SIGHT OF THE DOOR
Setting the Personal Entry Password
We recommend that you program your password now, before
you install the Keyless Entry. Then you can test the reception
at the mounting location before you proceed further.
For a one-piece door,
Figure 3
use the optional location shown in the
illustration (on the edge of the door jamb) to avoid injury
as the door swings up and out.
Choose a 4-digit password using the numbers from 0 to 9 (a
number can be used more than once, for example, 4,0, 4,1.)
Test the reception of the Keyless Entry by operating your
opener from the selected location. Change the location if
necessary.
If you have a Premium Control Console:
Door Control
Push button
1. With the door closed, press the four buttons for
the password, then press and hold Enter.
Keypad
Cover
Open the keypad and remove the
battery compartment screw and
cover to access the bottom
mounting hole (Figure 4).
2. Press and hold the light button on the door
control, Figure 1.
LIGHT
3. Press and hold the door control push button.
LOCK
Center the keypad at eye level
against the selected location. Mark
4 1/4" up the centerline from the
bottom and drill a 1/8" pilot hole.
Install top mounting screw, allowing
1/8" to protrude above surface.
Position keypad on screw head and
adjust for snug fit.
4. After the opener light flashes, release all
buttons.
Bottom
mounting hole
Light
Figure 1
If you do not have a Premium Control Console:
Battery
1. Enter the four digit password desired, then press and hold
Enter.
Battery
Cover
2. Press and release the SRT (learn) button on the door
opener panel, Figure 2.
With cover open so bottom
mounting hole is visible, use a punch to
mark hole. Remove keypad and drill 1/8" pilot hole. Replace
keypad and complete installation with bottom screw, using
care to avoid cracking plastic housing. Do not overtighten.
Figure 4
3. After the opener light flashes, release the Enter button.
Test by pressing your password, then press Enter. The door
should begin to move.
This procedure can be repeated with a different password for
use with a second garage door opener.
Replace the battery cover.
Orange
SRT (learn)
Button
1
2
3
Figure 2
Side two contains instructions for changing the personal
entry password and setting a temporary password.
Security✚
Garage Door Opener
9
9
1
1
Yellow
Indicator
Light
7
7
3
3
5
5
KG
KG
1
|