Quick Start Guide
H-1265
PAGE 1 OF 10
0808 IH-1265
Become familiar with the printer’s major components. See Figure 2.
Top
cover
Label roll
USB
connector
DC power
connector
Platen
release
Label feed path
and tear bar
Label
spool
Form-feed
Cable
channel
button and LED
Label eject
button
Figure 2
LabelWriter Printer Features
Your LabelWriter printer is a direct thermal printer and does not use ink or toner.
Instead, the printer uses heat from a thermal print head to print on specially
treated labels. Labels are the only supplies you will ever need to buy.
The form-feed button on the front of the printer advances a single label. The label
eject button is used to remove labels from the printer when changing rolls.
The LED status light visually shows the current state of the printer:
• Solid blue - power is on and the printer is ready.
•
Flashing blue - labels are not loaded properly or label spool is empty.
H-1265
PAGE 3 OF 10
0808 IH-1265
2. Installing the Software
NOTE Do not connect the printer to your computer until instructed to do so during
the software installation.
To install the software on a Windows system
1
Insert the LabelWriter CD into your CD-ROM drive. After a few seconds, the
installation screen appears.
If the installation screen does not appear:
a. Click Start, then Run on the Windows taskbar. The Run dialog box
appears.
b. Enter D:\install.exe (where D is the letter assigned to the CD-ROM drive)
and click OK.
2
Click Install and follow the instructions in the installer.
To install the software on a Mac OS system
1
Insert the DYMO LabelWriter CD into the CD-ROM drive.
After a few seconds, the DYMO Label Software Installer
icon appears. See Figure 3.
DYMO Label
Figure 3
2
Double-click the Installer icon and follow the instructions.
If you do not see your printer in the printer list when the installation is
complete, refer to the ReadMe file for instructions on how to add the printer.
H-1265
PAGE 4 OF 10
0808 IH-1265
3. Connecting your LabelWriter Printer
NOTE Do not connect the printer to your computer
until instructed to do so during the software
installation.
Power adapter
To connect the power
Power cord
1
2
3
4
5
Plug the power cord into the power adapter.
See Figure 4.
Figure 4
Plug the power adapter into the power connector
on the bottom of the printer. See Figure 5.
Power
USB
Plug the other end of the power cord into a
power outlet.
USB
24VDC
Plug the USB cable into the USB port on the
bottom of the printer. See Figure 5.
Cable
channel
Figure 5
Insert the power and USB cables through the
cable channel and set the printer down.
NOTE DO NOT CONNECT the other end of the USB cable to
your computer until asked to do so during the software
installation.
6
When prompted by the software installer, plug the USB
cable into a USB port.
Figure 6
H-1265
PAGE 5 OF 10
0808 IH-1265
4. Loading Labels
Spool
guide
Spool
spindle
To load a label roll
1
2
Press the form-feed button to eject the labels that
protected the printer during shipment.
Open the top cover and remove any packing
material inside the label compartment.
Figure 7
3
4
Remove the label spool from inside the cover.
Hold the spool spindle in your left hand and place the
label roll on the spindle so that the labels feed from
underneath and the left edge of the label roll is flush
against the side of the spool. See Figure 7.
Figure 8
5
6
Place the spool guide onto the right side of the spool
and press the guide tightly against the side of the
label roll, leaving no gap between the roll and the spool. See Figure 8.
NOTE The label roll must fit snugly against both sides of the
label spool, with no gaps, to avoid drifting as the labels feed
through the printer.
Insert the label spool into the slot in the printer cover with
the labels extending from underneath the roll. See Figure 9.
Figure 9
H-1265
PAGE 6 OF 10
0808 IH-1265
7
8
Align the left edge of the label with the left edge of the
label feed slot and insert the label into the slot. See
Figure 10.
The printer feeds the labels, stopping at the beginning
of the first label. If the printer does not feed the labels,
make sure the first label is fully inserted and then press
the form-feed button.
Figure 10
Close the top cover.
You are now ready to print your first label.
5. Printing your First Label
To print your first label
1 Start DYMO Label Software by doing one of the following:
•
•
For Windows, click Start, then Programs>DYMO Label>DYMO Label.
For Macintosh, double-click in the DYMO Label folder.
The first time you open the application, you are asked to register the
software. Registering the software ensures that you will be informed of any
software updates. You are also asked to enter your default return address.
2
3
4
At the main window, click once on the label and type some text.
Choose a font and a justification setting from the Formatting toolbar.
Click
to print the label.
H-1265
PAGE 7 OF 10
0808 IH-1265
Figure 11 highlights some of the major features available in DYMO Label
Software.
Verify and correct addresses
as you add them to the
Address Book.
Insert text you’ve
copied to the
Clipboard.
Insert text,
addresses, pictures,
rectangles, lines,
barcodes, dates, or
counters.
If you also have a tape
printer, two buttons
allow you to easily
switch between the
Label and Tape Editors.
Store your favorite
addresses in the
Address Book;
automatically insert
them on your label.
Figure 11
For complete details on using the software, refer to the DYMO Label Software User
Guide, located on the DYMO Label Software CD-ROM, and the online Help.
H-1265
PAGE 8 OF 10
0808 IH-1265
Printing Postage with
™
DYMO Stamps
You can now print postage right from your desktop using your LabelWriter 400
Turbo label printer. All you need is DYMO Stamps software, your LabelWriter
™
printer, DYMO Stamps labels, and an Internet connection.
To install DYMO Stamps and print postage
1
Sign up for your USPS account with Endicia. Go to:
2
At the end of the sign up process, download and install the DYMO Stamps
software.
DYMO Stamps software is available for both Windows and Mac OS X.
NOTE You must have DYMO Label Software and your LabelWriter printer
installed before installing the DYMO Stamps software.
The first time you start the DYMO
Stamps software, you are prompted
to enter the postage account
number assigned and the pass
phrase you created during the sign-
up process.
3
Enter your account number and
pass phrase, and then click OK.
H-1265
PAGE 9 OF 10
0808 IH-1265
4 Select Buy Postage from the
Account menu and purchase
postage for your account.
5 Select DYMO LabelWriter 400
Turbo from the Printer drop-
down list under Printer
Selection.
6
Click Test Print to print a
voided postage label.
You are now ready to start printing
actual postage whenever you need
it. Refer to the DYMO Stamps online
Help for more information about
using the software.
You can add postage, buy DYMO Stamps postage labels, and order supplies
directly from within the DYMO Stamps software.
PAGE 10 OF 10
0808 IH-1265
|