ETA Systems Power Supply ETA S15 User Manual

ETA-S15  
Power Conditioner & Distribution Unit  
ETA-S15  
Power Conditioner & Distribution Unit  
1601 Jack McKay Blvd. • Ennis, Texas 75119 U.S.A.  
Telephone: 800-321-6699 • Fax: 800-996-3821  
– 1 –  
ETAsys.com  
Specifications are subject to change without notice.  
 
ETA-S15  
Power Conditioner & Distribution Unit  
SAFETY INSTRUCTIONS  
The lightning flash with arrowhead symbol within an  
CAUTION  
equilateral triangle is intended to alert the user to the  
presence of uninsulated “dangerous voltage “ within the  
product’s enclosure that may be of sufficient magnitude  
to constitute a risk of electric shock to persons.  
RISK OF ELECTRIC SHOCK  
DO NOT OPEN  
RISQUE DE DECHARGE ELECTRIQUE  
´
ATTENTION  
-NE PAS OUVRIR.  
The exclamation point within an equilateral triangle is  
intended to alert the user to the presence of important  
operating and maintenance (servicing) instructions in the  
literature accompanying the product.  
WARNING  
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK  
DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.  
1. Read these instructions.  
2. Keep these instructions.  
3. Heed all warnings.  
4. Follow all instructions.  
5. Do not use this device near water.  
6. Clean only with dry cloth.  
7. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.  
8. Do not install near any heat sources such as radiators, heat registers, stoves, or other device (including amplifiers) that produce  
heat.  
9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the  
other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your  
safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.  
10. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they  
exit from the device.  
11. Only use attachments/accessories specified by the manufacturer.  
12.  
Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the device. When a  
cart is used use caution when moving the cart/device combination to avoid injury from tip-over.  
13.  
This product is equipped with a three-wire grounding-type plug, a plug having a third (grounding) pin. This plug will only  
fit into a grounding-type power outlet. This is a safety feature. If you are unable to insert the plug into the outlet, con-  
tact your electrician to replace your obsolete outlet. Do not defeat the safety purpose of the grounding-type plug.  
14. Unplug this device during lightning storms or when unused for long periods of time.  
15. Refer all servicing to qualified service personnel. Servicing is required when the device has been damaged in any way, such as  
power-supply cord or plug is damaged, liquid has been spilled, objects have fallen into the device, the device has been exposed to  
rain or moisture, does not operate normally, or has been dropped.  
16. To prevent fire or shock hazard. Do not expose this appliance to rain or moisture.  
This appliance shall not be exposed to dripping or splashing water and that no object filled with liquids such as vases shall be  
placed on apparatus.  
17. To completely disconnect this equipment from the mains, disconnect the power supply cord plug from the receptacle.  
18. The mains plug of the power supply cord shall remain readily operable.  
1601 Jack McKay Blvd. • Ennis, Texas 75119 U.S.A.  
Telephone: 800-321-6699 • Fax: 800-996-3821  
– 3 –  
ETAsys.com  
Specifications are subject to change without notice.  
 
ETA-S15  
Power Conditioner & Distribution Unit  
CAUTION– WHEN INSTALLING THE PRODUCT  
• Plugging in or unplugging the power cord with wet hands may result in electric shock.  
• Never move the device with the power cord plugged into the wall, as damage to the power cord may result.  
• When unplugging the cord from the wall, grasp the plug, NOT the cord.  
• Never install this device in humid or dusty locations, nor in direct sunlight, near sources of heat, or in areas where sooty smoke or  
steam are present. Fire and electric shock may result.  
• Keep all sides of the device at least 312” away from objects that may obstruct air flow to prevent the unit’s internal temperature  
rise.  
WARNING – WHEN THE DEVICE IS IN USE  
To prevent electric shock, do not remove the device cover as there are high voltage components inside. Refer all servicing to ETA  
Systems.  
• Should any of the following irregularities occur during use, immediately switch off the power, disconnect the power cord from  
the AC outlet and contact ETA Systems. Do not to attempt to continue operation of the device as this may cause fire or electric  
shock.  
• Smoke or strange smell coming from the unit.  
• If the device falls or the case is damaged.  
• If water or any metallic objects falls into the device.  
• If the power supply cord is damaged in any way.  
• If the device is malfunctioning.  
• Do not insert or drop metallic objects or flammable materials into the ventilation holes of the device’s cover, as this may result in  
electric shock or fire.  
• Do not place any containers with liquid or metallic objects on the top of the device.  
If any liquid spills into the unit, fire or electric shock may result.  
• Never operate this device or touch the power supply cord during an electrical storm, electric shock may result.  
• Never exceed the wattage on the product when connecting equipment. Fire and/or property damage may result.  
• Operate the device only with the voltage specified on the unit. Fire and/or electric shock may result if a higher voltage is used.  
• Do not modify, kink, or cut the power cord. Do not place the power cord in close proximity to heaters and do not place heavy  
objects on the power cord, including the device itself, doing so may result in fire or electrical shock.  
• Ensure that the safety ground terminal is connected to a proper ground. Never connect the ground to a gas pipe as a catastrophic  
disaster may result.  
• Be sure the installation of the product is stable, avoid slanted surfaces as the product may fall and cause injury or property  
damage.  
CAUTION – WHEN THE DEVICE IS IN USE  
• Never place heavy objects on the product, causing it to fall and/or break, resulting in personal injury and property damage. In addi-  
tion, the product itself may fall and cause injury and property damage.  
• Contact ETA Systems for instructions on cleaning the inside of the unit. Large accumulations of dust inside the unit may result in  
heat buildup and fire.  
• Ensure that the power supply plug is securely plugged into the wall outlet. Never allow dust to accumulate on the power plug or  
inside the wall outlet.  
• When cleaning the unit or the unit is not to be operated for an extended time period, unplug the power cord from the wall.  
1601 Jack McKay Blvd. • Ennis, Texas 75119 U.S.A.  
Telephone: 800-321-6699 • Fax: 800-996-3821  
– 4 –  
ETAsys.com  
Specifications are subject to change without notice.  
 
ETA-S15  
Power Conditioner & Distribution Unit  
INTRODUCTION  
Thank you for purchasing the ETA Systems ETA-S15 AC Power Conditioner & Distribution Unit. The ETA-S15 has been designed to  
meet most installation requirements for AC power distribution and equipment power protection.  
The ETA-S15 features noise filtering for unwanted Radio Frequency Interference (RFI) that is commonly introduced into AC lines by  
nearby radio transmitters or wireless products. EMI filters are incorporated to reduce noise from Electromagnetic Interference (EMI)  
from such items as electric motors and switching power supplies. The benefit of these filters can be seen on video products or audibly  
by reducing static pops and external signal interference.  
Unstable AC Mains voltage is one of the main reasons for equipment failure. The amount of energy that can be injected into the power  
system can be immense with voltages reaching 6kV or amperage peaks of 3000A. These spikes are very fast and usually only last for  
a very short period of time. The ETA-S15’s circuitry is very fast and can suppress unwanted energy within a nanosecond response and  
sustain the suppression up to 2 milliseconds, thus ensuring virtually trouble free protection.  
The ETA-S15 offers power management control, noise filtering, and spike/surge protection, making it the most compact, effective  
power management protection system on the market today.  
KEY FEATURES  
• 9 Total Outlets  
• 6 Rear Panel Switched Outlets and 2 Rear Panel Unswitched Outlets  
• 1 Front Panel Unswitched Convenience Outlet  
• RFI Noise Filtering to Reduce Radio Frequency Interference  
• EMI to Reduce Electromagnetic Interference  
• Circuit Breaker Protection @ 15A  
• Spike Suppression up to 6000V  
APPLICATIONS  
The ETA-S15 was designed to be flexible with features that allow it to be used in a variety of applications. The ETA-S15 can be used  
solely for protection against voltage surges or for AC distribution. If fuzzy video or frequent static pops occur, the AC power condition-  
ing may eliminate or reduce those inconveniences. The following are just a few examples of applications where the ETA-S15 can be  
used:  
• Restaurants  
• Houses of Worship  
• Schools  
• Home Theaters  
• Office Buildings  
• Sports Bars  
1601 Jack McKay Blvd. • Ennis, Texas 75119 U.S.A.  
Telephone: 800-321-6699 • Fax: 800-996-3821  
– 5 –  
ETAsys.com  
Specifications are subject to change without notice.  
 
ETA-S15  
Power Conditioner & Distribution Unit  
FRONT PANEL FEATURES  
1
2
3
1. Un-switched AC Outlet – The 120VAC outlet is always live when the ETA-S15 power cord is plugged into an AC mains power  
source and voltage is present. Note: The AC mains power switch does not affect the Unswitched AC Outlet. The Unswitched  
Outlet is protected by the surge protection circuitry.  
2. AC Mains Breaker – The 15A rated breaker will open if the combined draw of all AC outlets exceeds 15A. Note: The breaker is  
designed to exceed its rating for a short period of time. If the breaker is tripped, you must first remove the load from the ETA-S15  
and then push to reset.  
3. Power Switch To turn the ETA-S15 on or off, press the switch to the ON or OFF position. The power switch will illuminate  
when in the “On” position.  
REAR PANEL FEATURES  
2
3
1
1. AC Mains Input Connect the 9' (3m) power cord to a 15A 120VAC outlet to provide power to the ETA-S15.  
2. AC Switched Power Outlets These six outlets are “Live” when the front panel power switch is activated.  
3. AC Unswitched Power Outlets These two outlets are always “Live” when the ETA-S15 is plugged into a 120VAC source.  
INSTALLATION  
Before installing, we strongly suggest you read the entire manual to ensure you benefit from all the features of the ETA-S15. The  
ETA-S15 can be placed on a shelf or rack mounted in a standard 19" width rack. When rack mounted, placement within the rack is flex-  
ible however the ETA-S15 should be within 6' of a dedicated 15A AC outlet. When rack mounting, use Rack Rail screw type 1032" x 1".  
Always make sure the 15A outlet is properly inspected by a certified electrician prior to connecting the ETA-S15. Make sure to inspect  
the equipment that is to be plugged into the ETA-S15 to ensure it does not exceed 15A total amperage draw.  
1601 Jack McKay Blvd. • Ennis, Texas 75119 U.S.A.  
Telephone: 800-321-6699 • Fax: 800-996-3821  
– 6 –  
ETAsys.com  
Specifications are subject to change without notice.  
 
ETA-S15  
Power Conditioner & Distribution Unit  
SPECIFICATIONS  
Type  
Power Conditioner & Suppressor  
Load Rating  
15A  
Front Panel  
Outlets  
1 Unswitched  
Rocker  
Activation Switch  
Circuit Breaker  
Indicators  
15A Resettable  
AC Power On  
Rear Panel  
AC Outlets  
8 Outlets total, 6 Switched, 2 Unswitched  
9' (3m), 14-gauge  
AC Mains Power Cord  
Technical Data  
Current Rating  
15 amps  
Operating Voltage  
Min. Spike Clamping Voltage  
Max. Spike Clamping Voltage  
Max. Spike Clamping Resp. Time  
Spike Clamping Voltage @ 100A  
Maximum Surge Current  
Energy Rating @ 2ms  
Noise Attenuation EMI/RFI  
Temperature Range  
Humidity Range  
Mechanical  
102VAC – 132VAC  
460VRMS @ 3,000A  
6000V  
1 Nanosecond  
1250Vp for 20µs  
6,500A  
200 Joules  
10dB @ 10kHz / 40dB @ 100kHz / 100dB @ 10MHz  
5° – 35°c  
5% to 95% R.H.  
Chassis Finish  
Black  
Mounting  
Rack Mount, 1RU  
1.75" (1RU, 44.5mm)  
19" (482.6mm)  
5" (127mm)  
Height  
Width  
Depth  
Weight  
5 lbs (2.27kg)  
6 watts  
Power Consumption  
Agency Listings  
MET (UL 1449 Code)  
1601 Jack McKay Blvd. • Ennis, Texas 75119 U.S.A.  
Telephone: 800-321-6699 • Fax: 800-996-3821  
– 7 –  
ETAsys.com  
Specifications are subject to change without notice.  
 
ETA-S15  
Power Conditioner & Distribution Unit  
LIMITED WARRANTY  
All products manufactured by ETA Systems are warranted to the original dealer/installer, industrial or commercial purchaser to be  
free from defects in material and workmanship and to be in compliance with our published specifications, if any. This warranty  
shall extend from the date of purchase for a period of one year. Additionally, fuses and lamps carry no warranty. ETA Systems will  
solely at its discretion, replace at no charge or repair free of charge defective parts or products when the product has been applied  
and used in accordance with our published operation and installation instructions. We will not be responsible for defects caused by  
improper storage, misuse (including failure to provide reasonable and necessary maintenance), accident, abnormal atmospheres, water  
immersion, lightning discharge, or malfunctions when products have been modified or operated in excess of rated power, altered,  
serviced or installed in other than a workmanlike manner. The original sales invoice should be retained as evidence of purchase under  
the terms of this warranty. All warranty returns must comply with our returns policy set forth below. When products returned to ETA  
Systems do not qualify for repair or replacement under our warranty, repairs may be performed at prevailing costs for material and labor  
unless there is included with the returned product(s) a written request for an estimate of repair costs before any non-warranty work is  
performed. In the event of replacement or upon completion of repairs, return shipment will be made with the transportation charges  
collect.  
EXCEPT TO THE EXTENT THAT APPLICABLE LAW PREVENTS THE LIMITATION OF CONSEQUENTIAL DAMAGES FOR PERSONAL  
INJURY, ETA SYSTEMS SHALL NOT BE LIABLE IN TORT OR CONTRACT FOR ANY DIRECT, CONSEQUENTIAL OR INCIDENTAL  
LOSS OR DAMAGE ARISING OUT OF THE INSTALLATION, USE OR INABILITY TO USE THE PRODUCTS. THE ABOVE WARRANTY IS  
IN LIEU OF ALL OTHER WARRANTIES INCLUDING BUT NOT LIMITED TO WARRANTIES OF MERCHANTABILITY AND FITNESS FOR  
A PARTICULAR PURPOSE.  
ETA Systems does not assume, nor does it authorize any other person to assume or extend on its behalf, any other warranty,  
obligation, or liability. This warranty gives you specific legal rights and you may have other rights which vary from state to state.  
SERVICE  
Should your ETA-S15 require service, please contact the  
ETA Systems warranty department at  
1-877-689-8055, ext. 277 to obtain an RA number.  
ETA Systems Tech Support can be reached at 1-800-321-6699.  
©2009 ETA Systems All rights reserved. ETA003561 RevA 05/09  
1601 Jack McKay Blvd. • Ennis, Texas 75119 U.S.A.  
Telephone: 800-321-6699 • Fax: 800-996-3821  
– 8 –  
ETAsys.com  
Specifications are subject to change without notice.  
 

Clarion CD Player DB346MP User Manual
Contemporary Research Universal Remote ICC2 IRC User Manual
Cornelius Beverage Dispenser JS7 W25 User Manual
Coustic Car Stereo System RX 779 User Manual
Craftsman Trimmer 315CR2000 User Manual
Cuisinart Coffeemaker DTC 950 User Manual
Dimplex Heat Pump SI 11CS User Manual
Dixon Lawn Mower SE 5225 KOH CE User Manual
Fellowes Paper Shredder 99705 User Manual
Gaggenau Ventilation Hood AW 200 790 User Manual