Extron electronic Network Card PVT RGB CV MK User Manual

PVT RGB CV MK and PVT RGB MK Installation Guide  
The PVT RGB CV MK (2 -gang) and PVT RGB MK (1-gang) A/V wall plates for PoleVaultSystems can  
be installed in MK junction boxes.  
To install either of the devices,  
1. Run the A/V input cables (CAT 5/5e/6) from the PoleVault switcher along the raceway or behind  
the wall to the desired junction box location.  
N
Two cables (A and B) are needed for the RGB signals, one for composite video.  
2. Thread the cables through the back of the junction box and out of the front.  
3. Carefully cut off the terminating RJ-45 connector from each cable.  
4. Strip the insulator of each cable wire back approximately 0.4" (1.1 cm).  
5. Following the wiring diagram and table below, use a Tweeker to press down the spring switch,  
and insert each wire into its correct location in the connector on the rear panel of the applicable  
PVT. Release the spring to hold the wire securely in place.  
Step 3  
Step 4  
Strip the insulator  
0.4" (1.1 cm).  
RGB Signals  
568A  
Pin Wire Color  
Composite  
Video Signals  
568B  
Cut off the  
Wire Color  
Cable A  
Cable B  
RJ-45 connector.  
Top of  
device  
1
V. sync +  
V. sync –  
+ 5 VDC  
Audio L +  
Audio L –  
Video +  
Red +  
White-green  
White-orange  
Orange  
2
3
4
5
6
7
8
Green  
Red –  
Video –  
12345678  
White-orange  
Blue  
White-green  
Blue  
Cut below  
H. sync +  
Green +  
Green –  
H. sync –  
Blue +  
+ 5 VDC  
Audio L +  
Audio L –  
GND  
Step 5  
White-blue  
Orange  
White-blue  
Green  
Twisted  
Pairs  
Press to hold the spring open.  
Insert the wires according to  
the table.  
GND  
Audio R +  
Audio R –  
White-brown  
Brown  
White-brown  
Brown  
Audio R +  
Audio R –  
1&2  
7&8  
3&6 4&5  
Blue –  
Release to close the spring.  
PVT RGB CV MK and PVT RGB MK Installation Guide, cont’d  
6. Where applicable, connect an IR cable from the MediaLink Controller to the rear IR connector  
by inserting the signal wire into the hole marked “S”, and the ground wire into the  
hole marked “G” (see inset, step 6).  
7. Tighten down the screws.  
8. Push all excess wiring into the box.  
Step 6  
9. Using the supplied screws, attach the wall plate directly to the junction box.  
10. Connect the applicable input device and, where applicable, an IR emitter to the PVT.  
11. Power on the input device and the Polevault switcher.  
The PVT wall plate is powered by the PoleVault switcher.  
N
Refer to the “PoleVault System Installation Guide” to complete system installation and setup.  
UTP Cable  
Double Wide  
Dry Lining Box  
Extron  
PVT RGB CV MK  
RGB and Composite  
T
U
O
IR  
G
Line Driver  
S
K
M
V
C
B
G
R
T
V
P
3.5 x 30 mm  
Screw  
Extron Electronics, USA  
800.633.9876 714.491.1500  
FAX 714.491.1517  
Extron Electronics, Japan  
+81.3.3511.7655  
FAX +81.3.3511.7656  
68-1526-01  
Rev A  
Extron Electronics, Asia  
+800.7339.8766 +65.6383.4400  
FAX +65.6383.4664  
Extron Electronics, Europe  
+800.3987.6673 +31.33.453.4040  
FAX +31.33.453.4050  
03 08  
 

Compaq Mouse CPQ300iD User Manual
Cooper Lighting Computer Monitor 6109 User Manual
Craftsman Garage Door Opener 13918595 User Manual
Craftsman Saw 31528461 User Manual
Cuisinart Coffeemaker DGB 625 User Manual
Digicom Network Router SNT06 1 User Manual
Dixon Lawn Mower ZTR 3302 User Manual
Earthquake Sound Speaker IQ1500 User Manual
Edimax Technology Switch EK 08RO User Manual
Euro Pro Carpet Cleaner SE3318H User Manual