Tumble Dryer EDV278EL
Owner’s Manual
SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE
IMPORTANT SAFETY INSTRUCTIONS
WARNING!
n The dryer is made and marked to facilitate
recycling. When it is no longer useful, contact
your local refuse collection service for advice
on how to properly dispose of the dryer for
purposes of recycling.
To reduce the risk of fire, electric shock, or injury
to persons when using your appliance, follow basic
precautions, including the following:
n Read all instructions before using the appliance.
n Do not wash or dry articles that have been
previously cleaned in, washed in, soaked in, or
spotted with gasoline, dry-cleaning solvents,
cooking oils, other flammable or explosive
substances as they give off vapors that could
ignite or explode.
WARNING!
This appliance must be properly grounded.
GROUNDING INSTRUCTIONS
A) Grounding instructions for a grounded,
cord-connected appliance
n Do not allow children to play on or in the
appliance. Children should be closely
supervised when near the appliance.
In the event of malfunction or breakdown,
grounding will reduce the risk of electric shock by
providing a path of least resistance for electric
current. This appliance is equipped with a cord
having an equipment-grounding conductor and a
grounding plug. The plug must be plugged into an
appropriate outlet that is properly installed and
grounded in accordance with all local codes and
ordinances.
n Before the appliance is removed from service or
discarded, remove the door to the drying
compartment.
n Do not reach into the appliance if the drum is
moving.
n Do not install or store this appliance where it
will be exposed to the weather.
n Do not tamper with controls.
To reduce the risk of fire, this appliance must be
exhausted outdoors or the equivalent. Do not
exhaust into a chimney, wall, ceiling or concealed
space in a building.
n Do not attempt to repair or replace any part of
the appliance or perform any servicing unless
specifically recommended in this guide.
n Do not use fabric softeners or dryer sheets unless
the manufacturer gives written assurance that the
product will not damage a tumble dryer.
WARNING!
Improper connection of the equipment-grounding
conductor can result in a risk of electric shock.
Check with a qualified electrician or service
representative or personnel if you are in doubt as
to whether the appliance is properly grounded.
n Do not heat-dry items containing:
n •vinyl, plastic, foam rubber or similarly
textured rubberlike materials
n •fiberglass
n •wool unless the label specifies “washable”
Do not modify the plug provided with the appliance.
If it will not fit the outlet, have a proper outlet
installed by a qualified electrician.
n Clean the lint filter before or after each load.
n Keep the area around the exhaust opening and
adjacent surrounding areas free from the
accumulation of lint, dust and dirt.
B) Grounding instructions for a permanently
connected appliance:
n The interior of the machine should be cleaned
periodically by an authorized Eurotech service
agent.
This appliance must be connected to a grounded
metal, permanent wiring system, or an equipment-
grounding terminal or lead on the appliance.
n Do not place items exposed to cooking oils in
your dryer. Items contaminated with cooking oils
may contribute to a chemical reaction that could
cause a load to catch fire.
NOTE: This manual does not cover every possible
condition and situation that may occur. Use
common sense and caution when
installing, operating, and maintaining any
appliance.
n Electrical installation, if required, must be done
by a licensed electrician.
n Do not operate appliance while away from the
home.
n Do not heat dry items that have been dry-
cleaned.
SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE
3
DESCRIPTION OF THE MACHINE
♦ The tumble dryer is constructed in sheet steel panels with a treated and painted finish that ensures its
aesthetic quality remains unaltered over time.
♦ The motor(s) and all moving parts are designed for minimum noise levels.
♦ The stainless steel drum is large and well mounted to ensure a better quality tumble dryer and a longer
life of clothing.
♦ The control panel lets you use all the drying programs with ease.
♦ The door has a wide opening to facilitate easy loading and unloading of the laundry.
Control panel
Door
Pull-out
lint filter
Adjustable
legs
TECHNICAL INFORMATION
DIMENSIONS
Height
Drying system
Drum Capacity
Voltage
External discharge
33-1/4” (84.45 cm)
23-3/8” (59.37 cm)
106 liters
Width
208/230 V, 60 Hz
3300 W
Depth w/door closed 23-1/4” (60.30 cm)
Depth w/door open 39” (99.10 cm)
Heater loading
Weight
Approx . 83 lbs. (38 kg)
For additional information, see the type plate located on the door facing.
4
INSTALLATION INSTRUCTIONS
Read these instructions carefully before you install the machine. The installation should be carried out by a
qualified person who is familiar with all local codes and ordinances for electrical connections. Incorrect
installation may cause damage and/or injury. If the integrity of the machine is in doubt, do not use it. Call
your dealer for qualified assistance.
The dryer can be installed in any room with a hard floor. Do not install it on carpeting with heavy pile.
There must be a ventilation outlet to the exterior for the exhaust duct.
WARNING!
This appliance should never be exhausted into a chimney, wall, ceiling, or concealed space of a
building. Only a metal ventilation grill should be used.
To install the tumble dryer, follow the steps below:
1. Remove the outer wrapping and the polystyrene base.
2. Move the machine into place.
3. Adjust the levelling legs by lifting the front of the dryer slightly and adjusting the feet to the correct height.
Be careful not to screw the feet down too far and do not use a screwdriver.
NOTE: A badly leveled machine may result in damage to the bearings and premature wear, so we
recommend that you use a spirit level.
4. Connect the exhaust duct to the ventilation outlet (see below).
CONNECTING THE EXHAUST DUCT
You will need a UL-CSA-approved, 4-inch ridged metal exhaust duct.
NOTE: Excessive duct and too many bends can impede drying performance. We recommend that you cut
off any excess exhaust duct and run the duct with as few bends as possible. Make any necessary
bends as gentle as possible.
To connect the exhaust duct, follow the steps below:
1. Connect the exhaust duct to the coupling nut supplied with the dryer. (See illustration below.)
2. Turn the coupling (together with the duct) counterclockwise in the air discharge outlet on the back of the
dryer.
3. Connect the other end of the exhaust duct to a ventilation exhaust fitting or to a discharge duct in the wall
and secure with a clamp.
4. It is best if the duct does not sag.
5. After you push the dryer into place, make sure there aren’t any kinks in the duct.
NOTE: Maximum duct length of 25 feet, using two 90° elbows is allowed. Subtract 4 feet of duct for each
additional elbow.
5
ELECTRICAL CONNECTIONS
The power supply cord must be grounded. If the machine is to be used in a wet area, the supply must be
protected by a residual current device. Connection to a permanently wired supply point must be made only
by a qualified electrician.
As supplied: Single-phase, 230 V, 60 Hz, 3300 Watt heater, 30 A fuse required
CONNECTING A 3-WIRE POWER CORD
WARNING! Before starting this procedure, be sure the power is turned off at the breaker/fuse box.
You will need a 3-wire power supply cord with three No. 10 copper wires and a matching 3-wire receptacle
of NEMA Type 10-30R, as illustrated below:
Ring
This blade connects
Spade terminals
terminals
to this conductor.
with upturned ends
Neutral/
Ground
3/4” UL-listed
strain relief
(white)
Neutral/Ground
Follow the steps below to connect a 3-wire power cord:
1. Turn the power off at the breaker/fuse box.
2. Remove terminal block cover.
The numbers in the
illustration below correlate
to the step numbers.
4
3. Use the strain relief attached below the terminal block opening.
4. Loosen or remove center terminal block screw.
5. Connect neutral/ground (white) wire of power supply cord to the center,
silver-colored terminal screw. Tighten screw.
5
6. Connect the other wires to outer screws.
7. Tighten the strain relief screws.
6
8. Replace terminal box cover on back of dryer.
9. Plug dryer into wall receptacle.
7
10. Turn power on at breaker/fuse box.
6
CONNECTING A 4-WIRE POWER CORD
WARNING! Before starting this procedure, be sure the power is turned off at the breaker/fuse box.
You will need a 4-wire power supply cord with four No. 10 copper wires and a matching 4-wire receptacle of
NEMA Type 14-30R, as illustrated below. The fourth wire must be identified with a green cover and the
neutral conductor by a white cover.
3/4” UL-listed
strain relief
Spade terminals
with upturned ends
Neutral
Ring
terminals
Neutral
(white)
Ground
prong
Ground
(green)
Follow the steps below to connect a 4-wire power cord:
1. Turn the power off at the breaker/fuse box.
2. Remove terminal block cover.
The numbers in the
illustration below correlate
to the step numbers.
3. Use the strain relief attached below the terminal block opening.
4. Remove center terminal block screw.
5
4
6
5. Remove ground wire (green with yellow stripes) from external ground connector
screw. Fasten under center, silver-colored terminal block screw.
6. Connect ground (green) wire of cord to external ground conductor screw.
7. Connect neutral (white) wire of cord under center screw of terminal block.
8. Connect the other wires to outer screws.
9. Tighten the strain relief screws.
7
8
9
10. Replace terminal box cover on back of dryer.
11. Plug dryer into wall receptacle.
12. Turn power on at breaker/fuse box.
7
INSTRUCTIONS FOR USING THE TUMBLE DRYER
1. Make sure the lint filter is free of lint (see page 12).
2. Before placing the items in the dryer, sort the laundry by type of fabric and care label instructions (see
page 9).
3. Make sure nothing is in the garment pockets that could damage the clothes or the machine.
4. Close zippers and hooks to prevent snagging.
5. Load the laundry into the dryer.
6. Close the door securely.
7. Press the On/Off button to turn on the power (see page 10). The indicator light will glow to indicate the
power is on.
8. Set the Normal/Delicate temperature button to the desired setting (see page 10).
9. Set the Program knob to the desired program (see page 10).
10. Wait for a short beep then press the Start button (see page 10).
Drying times will vary due to the amount of laundry in the machine, moisture content, type of fabric, air
temperature and humidity. The length of the vent duct can also affect drying times (see page 5).
PREPARING THE LAUNDRY
For best drying results, clothes should be sorted properly. Most importantly, you should follow the care label
instructions (see page 9). Below are some suggestions on how to best sort your laundry for drying:
n Permanent press items should be dried together. For the most wrinkle-free results when drying permanent
press items, you should fill the machine only half full. These items also should be removed promptly
from the dryer and hung up or folded right away.
n Dry heavy fabrics together and lightweight fabrics together.
n Dry fabrics that shed lint (chenille, terry cloth, etc.) separately from fabrics that collect lint (synthetics,
velveteen, corduroy, etc.).
n Separate non-colorfast fabrics from light-colored items.
n If the care label says "Wash Separately," the fabric is likely to lose color (excess dye) for the first few
washings. To minimize the possibility of the dye transferring to white or lighter colored items, dry new
colored garments with items of similar color or alone. Bright reds and oranges on cottons are the dyes
most likely to transfer colors.
NOTE: Refer to page 3 for a list of specific materials that should never be put in a tumble dryer.
IMPORTANT:
Metal items (coins, nails, etc.) left in pockets, sharp buckles or similar items could damage the
drum. Remove any items of this kind before loading the dryer.
FABRIC SOFTENER AND DRYER SHEETS
We recommend using a liquid fabric softener in the washer’s rinse cycle. We do not recommend using
fabric softener sheets in the dryer. Over time, the chemicals on these sheets can build up inside the lint filter
and clog the holes that circulate the air.
8
CARE LABEL INSTRUCTIONS
Most clothes and other washable items have permanent care labels. Read these labels carefully! Care label
instructions and warnings should be followed for the best cleaning results.
The table below defines the typical symbols used on fabric care labels. (Note: Some manufacturers may use
slightly different symbols.)
CARE LABEL SYMBOLS
9
THE CONTROL PANEL
The control panel on your Eurotech tumble dryer is easy to understand and simple to operate.
START
DELICATE
NORMAL
ON/OFF
ON/OFF BUTTON
This button turns the power to the machine on and off. The power must be on before you can start a
program.
DELICATE/NORMAL BUTTON
This button lets you select between a normal and low drying temperature.
NOTE: Always refer to the care label on the garment to determine if it can be tumble dried. (See page 9.)
Normal: The Normal temperature setting is for sturdy fabrics, such as cotton, linen, and denim. If this
button is not pressed in, the temperature setting is Normal.
Delicate: The Delicate temperature setting is for synthetics, such as cotton/polyester blend, rayon, acetate,
washable silk or nylon. If this button is pressed in, the temperature setting is Delicate.
PROGRAM KNOB
To select a program, turn on the power then turn the program knob to the desired program. Wait for a short
beep, then press Start. After a brief pause, the program will begin.
The programs on the right of the dial are for cottons and linens. The programs on the bottom are for
synthetics. You can also set a Timed Dry program (on top left of dial) for 60, 40 or 20 minutes.
NOTE: The dryer will not start unless the door is closed securely and there are no items caught between the
door and the rubber gasket.
START BUTTON
After you have select the desired program and temperature option and heard the beep, press this button to
start the machine. The power must be on before you can start a program.
INDICATOR LIGHT AND END-OF-PROGRAM TONE
When you press the On/Off button, the indicator light below the program knob comes on and stays on
during the program. At the end of the program, the light flashes and an end-of-program tone sounds to
indicate the program is complete. This continues until the door is opened or the program knob is turned to
the 12:00 position.
COOL-DOWN
Every program ends with a cool-down cycle that is designed to reduce wrinkling. This means the clothes
will be cool when you remove them from the dryer, rather than scorching hot. After the cool-down cycle
ends, the light flashes and an end-of-program tone sounds to indicate the program is complete .
10
ANTI-CREASE
12:00 position
At then end of a program, if the knob is not turned to the 12:00
position or the door is not opened, the Anti-crease function begins.
This means that the drum rotates the clothes once every minute
to prevent creases from setting in. The Anti-crease and end-of-
program tone continue until you turn the program knob to the 12:00
position or open the door to remove the laundry.
ADDING AN ITEM
If you wish to interrupt a program to add or remove an item from
the dryer, simply open the door. The dryer will stop and the heating
element will shut off. After you have inserted the additional item(s)
into the dryer, close the door, wait for the beep, then press Start.
CHANGING A PROGRAM
If you decide to change the program setting after you have started the machine, simply turn the program
knob to the 12:00 position and wait for abeep. After the beep, turn the program knob to the desired program.
After a second beep, press Start.
RECOMMENDED PROGRAMS
AND TEMPERATURE SETTINGS
The table below is intended to help you determine which program is best for each type of load.
Cottons/Linens
Temp
Setting
Normal
Normal
Load
Size
Full
Fabric Type
Heavy cottons and denims
Cottons and linens w/out elastic and/or decorative
trim, white and colorfast items
Program
Extra Dry
Normal
Full
Synthetics
Temp
Setting
Delicate
Delicate
Load
Size
Half
Fabric Type
Program
Normal
Iron Dry
White and colorfast perma press
White and colorfast items that require ironing
Half
Polyester/acrylic blends, rayon, acetate
Washable silk and nylon
Damp Dry
Damp Dry
Delicate
Delicate
Half
Third
Timed
Temp
Setting
Normal
Normal
Load
Size
Full
Fabric Type
Program
60'
Heavy cottons and denims
Cottons and linens w/out elastic and/or decorative
trim, white and colorfast items
40'
Full
White and colorfast perma press
White and colorfast items that require ironing
40'
20'
Delicate
Delicate
Half
Half
Polyester/acrylic blends, rayon, acetate
Washable silk and nylon
20'
20'
Delicate
Delicate
Half
Third
11
CARE AND MAINTENANCE INSTRUCTIONS
The tumble dryer does not require special care. To best ensure a long life, however, certain precautions are
recommended (see page 3).
CLEANING THE LINT FILTER
You should clean the lint from the lint filter before every load. To do this, follow the instructions below:
1. Remove the filter from its holder by pulling it upwards.
2. Open the filter and gently run your hand across it to
collect the lint. If you prefer, you can clean it with a
soft brush.
3. Replace the filter into its holder.
NOTE: If you use dryer sheets, the filter should be
washed periodically with a mild soap and water
to remove any small particles that may have col-
lected in the holes.
CLEANING THE CONTROL PANEL
WARNING!
Before performing the operations described below, make sure that the power is off and the unit
is unplugged.
To clean the control panel, use only a warm, damp cloth. To prevent penetration of liquid into the door lock
and electrical components, never spray water or cleaning solvents on the control panel.
Also, never use abrasive cleaners or scouring pads on the outer surfaces because they will scratch the
finish and could remove the writing on the control panel. Some paper towels may also scratch the finish.
CLEANING THE EXHAUST DUCT
About once a year you should remove the exhaust duct and clean it. At this time, you should also clean the
exhaust outlet on the machine and the ventilation duct.
Periodically, you should check the dryer exhaust outside to be sure the air flow is strong and nothing is
blocking the vent.
12
TROUBLESHOOTING
Before calling for technical assistance, check that the operations described below have been carried out
correctly. This will save both time and money.
The machine won’t start.
n Make sure the indicator light is on.
n Make sure the door is closed securely.
n Make sure you pressed the START button.
n Check that you set the program or time correctly.
n Check that the electric plug is securely in the socket.
n Check the house breaker/fuses.
The machine takes too long to dry my laundry.
n Check that the lint filter is clean.
n If you use dryer sheets, you may need to wash the lint filter with warm water and a soft brush to clean any
blocked holes.
n Be careful not to overload the dryer because the warm air needs sufficient room to circulate properly and
the clothes need room to tumble freely.
n The laundry should only be damp when it comes out of the washer. If it seems too wet, try using a faster
or longer spin cycle.
n Make sure the outside vent exhaust is not blocked.
My clothes are coming out wrinkled.
n You should remove the clothes as soon as the dryer signals the end of the cycle.
n Dry heavy fabrics together and light fabrics together.
n Dry only permanent press items together.
n Dry in smaller loads.
n Use slower spin speeds in the washer.
n Use fabric softener in the washer’s rinse program.
n You may be using the wrong wash temperature. Try using a lower wash temperature, especially for
permanent press and delicate items.
The motor is running but the drum isn’t turning.
n This usually means a belt is broken. Call a servicer.
If you think you have resolved the problem, try starting the machine again. If the problem persists, call for
technical assistance (see page 15).
BEFORE CALLING FOR SERVICE
Before calling for service or contacting AM Appliance Group regarding a warranty issue, be prepared to
explain:
1) Model number of the machine
2) Serial number of the machine (located on the inner door facing)
3) Specific problem
13
NOTES
14
PRODUCT WARRANTY
MODEL EDV278EL
Be sure to complete the Warranty Registration Card you received with your appliance and mail it to
AM Appliance Group to validate your appliance warranty.
Cosmetic damage must be reported to your dealer within five days from the date of purchase. After
unpacking the washer, thoroughly check the unit for cosmetic damage.
FOR RESIDENTIAL INSTALLATIONS ONLY
LENGTH OF WARRANTY
AM APPLIANCE GROUP WILL PAY FOR:
One-Year Full
From date of purchase.
Eurotech replacement parts and/or repair labor to correct defect in
materials or workmanship. Service must be provided by an authorized
Eurotech service agent.
Two-Year Limited
From date of purchase.
Eurotech replacement parts (labor costs not included) for all parts due
to defect in materials or wormkanship. Service must be provided by
an authorized Eurotech service agent.
Five-Year Limited
From date of purchase.
Eurotech replacement parts (labor costs not included) for any defective
solid-state controls, timers, motors, or pumps. Replacement of cabinets
that may have rusted through. Service must be provided by an
authorized Eurotech service agent.
Ninety-Nine Year Limited
Eurotech replacement parts (labor costs not included) for the stainless
steel inner or outer drum if either fails to hold water due to a
manufacturing defect, such as rusting or cracking. Service must be
provided by an authorized Eurotech service agent.
AM APPLIANCE GROUP WILL NOT PAY FOR:
A. Service calls to:
1. Correct the installation of the appliance.
2. Repair damage due to shipment, delivery, installation, misuse or abuse.
3. Instruct how to use the appliance.
4. Replace house fuses or correct house wiring.
5. Correct house plumbing, including drain problems related to improper installation.
6. Clean or service air device in drain line.
B. Repair and/or replacement parts for failure of product if appliance is used for other than home/
residential use.
C. Damage resulting from accident, fire, floods, acts of God, alteration, misuse, abuse, improper
installation, or installation not in accordance with local electrical or plumbing codes.
D. Any shipping costs for parts during the limited warranty period.
E. Replacement parts or repair labor costs for units operated outside the continental United States.
F. Pickup and delivery. Eurotech appliances are designed to be repaired in the home.
IN NO EVENT SHALL AM APPLIANCE GROUP BE RESPONSIBLE
FOR ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES.
Some states will not allow the exclusion or limitation of incidental or consequential damages, so this
exclusion or limitation may not apply to you. This warranty gives you specific legal rights and you may
also have other rights which vary from state to state.
For warranty service, contact the dealer from whom you purchased the unit or an authorized Eurotech
service agent. Service will be provided during normal business hours. Should you have a service problem
that cannot be resolved locally, contact AM Appliance Group at the numbers listed below. Before calling for
service or contacting AM Appliance Group regarding a warranty issue, make a note of the model, type
name, and serial number, which is located on the inner door facing.
Or call our
Customer Service Center at
800-898-1879 or 972-238-0794
Write to us at:
AM Appliance Group
P. O. Box 851805
Richardson, Texas 75085-1805
15
QUICK START REFERENCE
(Refer to pages 10 and 11 for detailed operating instructions.)
Start Button
Delicate/Normal Button
After you have selected a program and the
temperature option (Delicate/Normal), wait for a
beep then press this button to start the program.
This button lets you select between a normal and low
drying temperature. Press it in to select the Delicate
(low) temperature and release it to select Normal.
START
DELICATE
NORMAL
Indicator
Light
Glows during
a program.
ON/OFF
Program Knob
On/Off Button
This button turns
the power to the
machine on and
off.
To select a program, turn the program knob to the desired program. Wait for a short
beep then press Start. After a brief pause, the program will begin.
The programs on the right of the dial are for cottons and linens. The programs on the
bottom are for synthetics. You can also set a timed dry program (on top left of dial) for
60, 40 or 20 minutes.
RECOMMENDED PROGRAMS AND TEMPERATURE SETTINGS
The table below is intended to help you determine which program is best for each type of load.
Cottons/Linens
Temp
Setting
Normal
Normal
Load
Size
Full
Fabric Type
Heavy cottons and denims
Cottons and linens w/out elastic and/or
decorative trim, white and colorfast items
Program
Extra Dry
Normal
Full
Synthetics
Temp
Setting
Delicate
Delicate
Load
Size
Half
Fabric Type
White and colorfast perma press
White and colorfast items that require
ironing
Program
Normal
Iron Dry
Half
Polyester/acrylic blends, rayon, acetate
Washable silk and nylon
Damp Dry
Damp Dry
Delicate
Delicate
Half
Third
Timed
Temp
Setting
Normal
Normal
Load
Size
Full
Fabric Type
Program
60'
Heavy cottons and denims
Cottons and linens w/out elastic and/or
decorative trim, white and colorfast items
White and colorfast perma press
White and colorfast items that require
ironing
40'
Full
40'
20'
Delicate
Delicate
Half
Half
Polyester/acrylic blends, rayon, acetate
Washable silk and nylon
20'
20'
Delicate
Delicate
Half
Third
16
|