Cool-Down Cycle
TROUBLESHOOTING
This shredder is protected with a special safety feature which
prevents the motor from overheating with extensive use. When
shredding is attempted beyond the machine's maximum
running time, the shredder will automatically shut off its
motor until it has cooled to an acceptable operating level.
This is normal and the shredder will return to operation after
the cool-down or “off” period. See Product Usage Guide (page
2) for maximum running time and related cooling “off” time.
Shredder will not
operate.
a. Shredder is not plugged in.
PAPER SHREDDER
b. Power switch is in the OFF position.
Move switch to AUTO position.
Personal Series
c. Shredder is jammed. See Clearing a
Jam.
d. Shredder has exceeded the
maximum run time and requires a
"cool-down" time. SeeProduct
Usage Guide.
Clearing a Jam
If the shredder sheet capacity is exceeded or paper is not put
in straight, a jam may result. See Product Usage Guide (page
2) for maximum sheet capacity for your shredder.
e. Shredder is not assembled properly.
SeeAssembly.
f. Safety tab may be broken. Turn
shredder head around and lower
back onto basket to use back-up
safety tab on other side of basket.
SeeAssembly.
To clear a jam:
1. Move the power switch to the REVERSE position. (NOTE:
If waste basket is full, empty it before clearing jam.) The
shredder will reverse the paper to clear the jam.
2. If the shredder jams in reverse, move the power switch to
AUTO and shredder will run for about two seconds. If jam
does not clear, move power switch to REVERSE again and
allow to run for about three seconds. Repeat this
procedure until the jam is cleared. If necessary, grasp the
paper carefully and pull out to clear the jam.
3. Once the jam is cleared, move the power switch to A U TO
for continued shredding or OFF if shredding is complete.
a. Shredder has exceeded the
maximum run time and requires a
"cool-down" time. SeeProduct
Usage Guide.
Shredder suddenly
stops while
shredding.
b. Shredder is jammed. See Clearing a
Jam.
Shredder operates
only in REVERSE.
A small piece of paper may be
blocking the auto-start sensor. Move
the power switch to the OFF position
and unplug the shredder. Turn
shredder over and use a toothpick
(from the underside of the unit) to
clear the paper blockage at the auto-
start sensor (center) location.
LIMITED WARRANTY
Fellowes, Inc. warrants the machine to be free from defects in
material and workmanship for 1 year from the date of
purchase by the original consumer. If any part is found to be
defective during the warranty period, your sole and exclusive
remedy will be repair or replacement, at Fellowes’ option and
expense, of the defective part.
Shredder runs
continuously when
in AUTO.
A small piece of paper may be causing
the auto-start feature to run
continuously. Move the power switch
to the OFF position and unplug the
shredder.Use a toothpick (from the
top of the unit) to clear the paper
blockage at the auto-start sensor
(center) location.
This warranty does not apply in cases of abuse, mishandling
or unauthorized repair. ANY IMPLIEDWARRANTY,
INCLUDING T H AT OF MERCHANTABILITY OR FITNESS
FOR A PA RTICULAR PURPOSE, IS HEREBY LIMITED IN
DURATION TO THE APPROPRIATE WARRANTY PERIOD
SET F O RTH ABOVE. IN NO EVENT SHALL FELLOWES BE
LIABLE FOR ANY CONSEQUENTIAL OR INCIDENTAL
DAMAGES ATTRIBUTABLE TO THIS PRODUCT. This
warranty gives you specific legal rights. You may have other
legal rights that vary from this warranty. The duration, terms
and conditions of this warranty are valid worldwide, except
where different limitations, restrictions or conditions may be
required by local law. For more details or to obtain service
under this warranty, please contact us or your dealer.
Shredder runs for a
few seconds after
the paper has
This is normal. The shredder runs a
few seconds longer than the paper in
order to keep the cutters clear of
paper particles and reduce the
chances of a jam.
cleared the cutters.
USE AND CARE MANUAL
PLEASE READ AND SAVE THIS MANUAL WITH YOUR ORIGINAL RECEIPT
Customer Service: 1-800-955-0959
© 2007 Fellowes, Inc. Form No. 402316 Rev C
|