Use & Care Manual
Single-Door
Refrigerator
Welcome & Congratulations 2
Safety Instructions
Installation
2-3
3-4
Features at a Glance
Temperature Controls
Looking Inside
4
4
5-6
6
Food Storage
& Energy Saving Tips
Care & Cleaning
Warranty
7
8
BeforeYou Call
9-10
P/N 297081600 (Jan 06)
READ AND SAVE THESE INSTRUCTIONS
SAFETY INSTRUCTIONS
INSTALLATION
This Owner’s Guide provides specific operating instructions for
your model. Use the refrigerator only as instructed in this
Owner’s Guide. Before starting the refrigerator, follow these
important first steps.
WARNING
ELECTRICAL INFORMATION
These guidelines must be followed to ensure that safety
mechanisms in the design of this refrigerator will operate
properly.
INSTALLATION
•
Choose a place that is near a grounded electrical outlet. Do
Not use an extension cord or an adapter plug.
•
Refer to the serial plate for correct electrical rating.
The power cord of the appliance is equipped with a
three-prong grounding plug for your protection against
shock hazards. It must be plugged directly into a
properly grounded three-prong receptacle. The power
supply circuit must be installed in accordance with
current edition of the National Electrical Code (NFPA
70) and local codes and ordinances. Consult a qualified
electrician. Receptacles protected by Ground Fault
Circuit Interrupters (GFIC) are NOT RECOMMENDED.
Do not use an extension cord or adapter plug.
If voltage varies by 10% or more, refrigerator performance
may be affected. Operating refrigerator with insufficient
power can damage the motor. Such damage is not
covered under the warranty. If you suspect your house
voltage is high or low, consult your power company for
testing.
•
For the most efficient operation, the refrigerator should be
located where surrounding temperatures will not drop
below 40° F (5° C) or exceed 110° F (43° C).
•
Allow the following clearances for ease of installation,
proper air circulation, and electrical connections:
Sides
Back & Top
3/8” minimum
1” minimum
•
Do Not block the toe grille on the lower front of your
refrigerator. Sufficient air circulation is essential for the
proper operation of your refrigerator.
•
Refrigerator
•
•
To prevent the refrigerator from being turned off
accidentically, do not plug unit into an outlet controlled
by a wall switch or pull cord.
Do not pinch, knot, or bend the cord in any manner.
OTHER PRECAUTIONS
•
•
To defrost refrigerator, always unplug unit first.
Never unplug the refrigerator by pulling on the cord. Always
grip the plug firmly, and pull straight out from the receptacle.
Freezer
NOTE
Turning the temperature control to OFF turns off the
compressor, but does not disconnect the power to the light
bulb or other electrical components.
Installation
NOTE
The exterior walls of the refrigerator may become quite warm
as the compressor works to transfer heat from the inside.
Temperatures as much as 30° F warmer than room
temperature can be expected.
WARNING
Avoid fire hazard or
electric shock. Do not use
an extension cord or an
adapter plug. Do not
remove any prong from
the power cord.
DOOR OPENING
NOTE
If your refrigerator is placed with the door hinge side against a
wall, you may have to allow additional space so the door can
be opened wider.
3
LEVELING
DOOR REMOVAL
If door must be removed :
The refrigerator must have all bottom corners resting firmly on a
solid floor. The floor must be strong enough to support a fully
loaded refrigerator . NOTE: It is Very Important for your
refrigerator to be level in order to function properly. If the
1. Gently lay refrigerator on its back, on a rug or blanket.
2. Remove two base screws and base panel.
3. Remove bottom hinge screws.
refrigerator is not leveled
during installation, the
door may be misaligned
and not close or seal
properly, causing
Unpacking and Leveling
4. Remove plastic top hinge cover.
5. Remove screws from top hinge.
6. Remove top hinge from cabinet.
7. Remove door and bottom hinge from cabinet.
8. To replace door, reverse the above order and securely
tighten all screws to prevent hinge slippage.
Turn
Left To
Raise
Turn
Right To
Lower
cooling, frost, or moisture
problems.
Plastic
Leveling Feet
To Level Refrigerator:
Crating
Screw
FEATURES AT A GLANCE
After discarding crating
screws and wood base,
use a carpenter’s level to
level the refrigerator from
front-to-back. Adjust the
plastic leveling feet in
front, ½ bubble higher, so
that the door closes
Discard The (4) Crating Screws
And (2) Wood Bases
easily when left halfway
open.
Unpacking and Leveling
Leveling Instructions for all Refrigerator/Freezer Pair:
•
Remove two leg levelers provided in literature bag. While
unit is lying on its back for wood skid removal, install both
leg levelers in rear of unit.
•
•
•
Level door of first unit using all four levelers and slide unit
into place. Recheck for levelness and adjust if necessary.
Measure distance from floor to bottom of door on first unit.
Adjust and level second unit so door height matches.
Leg Level Adjustments
•
•
One full turn of all four leg levelers will raise door 5/32”.
One full turn of both front leg levelers will raise door
3/16” and tilt top of door back 7/16”.
•
•
One full turn of both rear leg levelers will lower door
1/32” and tilt top of door forward 7/16”.
One full turn of both side leg levelers will raise door
3/16” and tilt top of door 3/8”.
TEMPERATURE CONTROLS
COOL DOWN PERIOD
•
•
Slide second unit into place leaving a minimum gap of 3/16”
between units for door swing clearance.
This last step may require at least one extraction of the
second unit to properly align units in a “built-in” application.
For safe food storage, allow 4 hours for the refrigerator to
cool down completely. The refrigerator will run continuously
for the first several hours.
TEMPERATURE CONTROL
The temperature control is located inside the refrigerator
compartment. The temperature is factory
preset to provide satisfactory food storage
temperatures. However, the temperature
control is adjustable to provide a range of
temperatures for your personal satisfaction.
If a colder temperature is desired, turn the
temperature control knob toward COLDEST
and allow several hours for temperatures to
CAUTION
To allow door to close and seal properly, do not let food
packages extend past the front of the shelves
stabilize between adjustments.
Cold Control
Shelf Front
4
TO ADJUST CANTILEVER SHELVES
LOOKING INSIDE
NOTE
INTERIOR LIGHTING
Cantilever shelves are supported at the back of the
refrigerator.
The lights come on automatically when the door is opened. To
replace the light bulb, turn the temperature control to OFF and
unplug the electrical cord. Replace the old bulb with a bulb of
the same wattage.
1
2
Lift front edge up.
Pull shelf out.
MID LEVEL LIGHTING
Replace the shelf by
The light comes on automatically when the door is opened. To
replace the light bulb, turn the temperature control to OFF and
unplug the electrical cord. Remove the lens from the lamp
housing by unsnapping it from the lamp housing using your
fingers or a screwdriver. Be careful not to break the locking tabs
on the lamp housing. Replace the old bulb with a bulb of the
same type and wattage. To replace the lens, snap one side of
the lens opening to the tab on the lamp housing. Then carefully
attach the other side.
inserting the hooks at rear of
the shelf into the wall
bracket. Lower the shelf into
the desired slots and lock
into position.
DOOR STORAGE
Door bins, shelves, and racks are provided for convenient
storage of jars, bottles, and cans. Frequently used items can be
quickly selected.
Some models have door racks or bins that can accommodate
gallon-sized plastic drink containers and economy-sized jars
and containers.
The dairy compartment, which is warmer than the general food
storage section, is intended for short term storage of cheese,
spreads, or butter.
ADJUSTABLE DOOR BINS
Some models have adjustable door
bins that can be moved to suit
individual needs.
To move door bins
1. Lift bin straight up.
2. Remove bin.
3. Place bin in desired position.
4. Lower bin onto supports
until locked in place.
Adjustable Door Bin
DELI DRAWER
CAUTION
(SOME MODELS)
To avoid personal injury or property damage, handle
tempered glass shelves carefully. Shelves may break
suddenly if nicked, scratched, or exposed to sudden
temperature change.
Some models are equipped
with a Deli Drawer for storage
of luncheon meats, spreads,
cheeses, and other deli items.
Deli Drawer
ADJUSTABLE INTERIOR
SHELVES
CRISPERS
(SOME MODELS)
The crispers, located under
the bottom refrigerator shelf,
are designed for storing fruits,
vegetables, and other fresh
produce. Wash items in clear
water and remove excess
water before placing them in
the crispers. Items with strong
odors or high moisture content
Multi-position adjustable interior
shelves can be moved to any
position for larger or smaller
packages. The shipping spacers
that stabilize the shelves for
shipping may be removed and
discarded.
should be wrapped before
storing.
Crisper Drawer
5
HUMIDITY CONTROL (SOME MODELS)
VACATION AND MOVINGTIPS
ShortVacations:
The Humidity Control, present on some models with crisper
drawers, allows you to adjust the humidity within the crisper. This
can extend the life of fresh vegetables that keep best in high
humidity.
Leave the refrigerator operating during vacations of less
than three weeks.
Long Vacations:
If the refrigerator will not be used for several months:
NOTE
Leafy vegetables keep best
when stored with the
Humidity Control set on
High Humidity, or in a
drawer without a Humidity
Control. This keeps
incoming air to a minimum
and maintains maximum
moisture content.
•
•
•
Remove all food and unplug the power cord.
Clean and dry the interior thoroughly.
Leave the refrigerator door open slightly, blocking it open if
necessary, to prevent odor and mold growth.
Crisper
Humidity Control
Moving: When moving the refrigerator, follow these
guidelines to prevent damage:
•
•
•
Disconnect the power cord plug from the wall outlet.
Remove foods, then defrost, and clean the refrigerator.
Secure all loose items such as base panel, baskets, and
shelves by taping them securely in place to prevent
damage.
In the moving vehicle, secure refrigerator in an upright
position to prevent movement. Also protect outside of
refrigerator with a blanket, or similar item.
FOOD STORAGE AND
ENERGY SAVING TIPS
•
FOOD STORAGE IDEAS
Fresh Food Storage
•
•
The fresh food compartment should be kept between 34° F
and 40° F with an optimum temperature of 37° F.
Avoid overcrowding the refrigerator shelves. This reduces
the circulation of air around the food and results in uneven
cooling.
Fruits andVegetables
•
Storage in the crisper drawers traps moisture to help
preserve the fruit and vegetable quality for longer time
periods.
Meat
•
Raw meat and poultry should be wrapped securely so
leakage and contamination of other foods or surfaces does
not occur.
ENERGY SAVING IDEAS
•
Locate the refrigerator in the coolest
part of the room, out of direct
sunlight, and away from heating ducts
or registers. Do not place the
refrigerator next to heat-producing
appliances such as a range, oven, or
dishwasher. If this is not possible, a
section of cabinetry or an added layer
of insulation between the two appliances will help the
refrigerator operate more efficiently.
•
•
Level the refrigerator so that the door closes tightly.
Refer to the “SETTINGTHETEMPERATURE CONTROL”
section for the suggested temperature control settings.
Do not overcrowd the refrigerator or block cold air vents.
Doing so causes the refrigerator to run longer and use
more energy.
Cover foods and wipe containers dry before placing them
in the refrigerator. This cuts down on moisture build-up
inside the unit.
•
•
•
Organize the refrigerator to reduce door openings. Remove
as many items as needed at one time and close the door
as soon as possible.
6
CARE AND CLEANING
Keep your refrigerator clean to prevent odor build-up. Wipe up
NOTE
any spills immediately and clean at least twice a year. Never
use metallic scouring pads, brushes, abrasive cleaners or
strong alkaline solutions on any surface. Do not wash any
removable parts in a dishwasher. Always unplug the electrical
power cord from the wall outlet before cleaning.
•
Turning the refrigerator temperature control to “OFF” turns
off the compressor, but does not disconnect electrical
power to the light bulb or other electrical components. To
turn off power to your refrigerator, you must unplug the
power cord from the wall outlet.
•
Do not use razor blades or other sharp instruments which
can scratch the appliance surface when removing
adhesive labels. Any glue left from tape or labels can be
removed with a mixture of warm water and mild
detergent, or, touch the glue residue with the sticky side of
tape you have already removed. Do not remove the
serial plate.
CAUTION
•
•
When moving the refrigerator, pull straight out. Do not
shift the refrigerator from side to side as this may tear
or gouge the floor covering.
Damp objects stick to cold metal surfaces. Do not
touch interior metal surfaces with wet or damp hands.
Care & Cleaning Chart
Tips and Precautions
Part
What To Use
Interior/Door
Liner
Use 2 tablespoons of baking soda in 1 quart of warm water. Be sure to wring
excess water out of sponge or cloth before cleaning around controls,
light bulb or any electrical part.
•
•
Soap and water
Baking soda and water
Wipe gaskets with a clean soft cloth.
Door Gaskets
Drawers/Bins
Glass Shelves
•
•
Soap and water
Soap and water
Do not wash any removable items (bins, drawers, etc.) in dishwasher.
Allow glass to warm to room temperature before immersing in warm water.
•
•
•
•
•
Soap and water
Glass cleaner
Mild liquid sprays
Soap and water
Non Abrasive Glass
Cleaner
Do not use commercial household cleaners, ammonia, or alcohol to clean
handles. Use a soft cloth to clean smooth handles. Do Not use a dry cloth to
clean smooth doors.
Exterior and
Handles
Clean stainless steel front and handles with non-abrasive soapy water and a
dishcloth. Rinse with clean water and a soft cloth. Wipe stubborn spots with an
ammonia-soaked paper towel, and rinse. Use a non-abrasive stainless steel
cleaner. These cleaners can be purchased at most home improvement or
major department stores. Always follow manufacturer's instructions.
NOTE: Always clean, wipe and dry with the grain to prevent cross-grain
scratching. Wash the rest of the cabinet with warm water and mild liquid
detergent. Rinse well, and wipe dry with a clean soft cloth.
•
•
•
Soap and water
Ammonia
Stainless Steel Cleaners
Exterior and
Handles
(Stainless Steel
Models Only)
7
Major Appliance Warranty Information
Your appliance is covered by a one year limited warranty. For one year from your original date of
purchase, Electrolux will pay all costs for repairing or replacing any parts of this appliance that prove to
be defective in materials or workmanship when such appliance is installed, used and maintained in
accordance with the provided instructions.
Exclusions
This warranty does not cover the following:
1. Products with original serial numbers that have been removed, altered or cannot be readily determined.
2. Product that has been transferred from its original owner to another party or removed outside the USA or
Canada.
3. Rust on the interior or exterior of the unit.
4. Products purchased "as-is" are not covered by this warranty.
5. Food loss due to any refrigerator or freezer failures.
6. Products used in a commercial setting.
7. Service calls which do not involve malfunction or defects in materials or workmanship, or for appliances
not in ordinary household use or used other than in accordance with the provided instructions.
8. Service calls to correct the installation of your appliance or to instruct you how to use your appliance.
9. Expenses for making the appliance accessible for servicing, such as removal of trim, cupboards, shelves,
etc.,which are not a part of the appliance when it is shipped from the factory.
10. Service calls to repair or replace appliance light bulbs, air filters, water filters, other consumables, or
knobs, handles, or other cosmetic parts.
11. Surcharges including, but not limited to, any after hour, weekend, or holiday service calls, tolls, ferry trip
charges, or mileage expense for service calls to remote areas, including the state of Alaska.
12. Damages to the finish of appliance or home incurred during installation, including but not limited to floors,
cabinets, walls, etc.
13. Damages caused by: services performed by unauthorized service companies; use of parts other than
genuine Electrolux parts or parts obtained from persons other than authorized service companies; or
external causes such as abuse, misuse, inadequate power supply, accidents, fires, or acts of God.
DISCLAIMER OF IMPLIED WARRANTIES; LIMITATION OF REMEDIES
CUSTOMER’S SOLE AND EXCLUSIVE REMEDY UNDER THIS LIMITED WARRANTY SHALL BE PRODUCT
REPAIR OR REPLACEMENT AS PROVIDED HEREIN. CLAIMS BASED ON IMPLIED WARRANTIES,
INCLUDING WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, ARE
LIMITED TO ONE YEAR OR THE SHORTEST PERIOD ALLOWED BY LAW, BUT NOT LESS THAN ONE YEAR.
ELECTROLUX SHALL NOT BE LIABLE FOR CONSEQUENTIAL OR INCIDENTAL DAMAGES SUCH AS
PROPERTY DAMAGE AND INCIDENTAL EXPENSES RESULTING FROM ANY BREACH OF THIS WRITTEN
LIMITED WARRANTY OR ANY IMPLIED WARRANTY. SOME STATES AND PROVINCES DO NOT ALLOW THE
EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, OR LIMITATIONS ON THE
DURATION OF IMPLIED WARRANTIES, SO THESE LIMITATIONS OR EXCLUSIONS MAY NOT APPLY TO
YOU. THIS WRITTEN WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS. YOU MAY ALSO HAVE OTHER
RIGHTS THAT VARY FROM STATE TO STATE.
If You Need
Service
Keep your receipt, delivery slip, or some other appropriate payment record to establish the warranty period
should service be required. If service is performed, it is in your best interest to obtain and keep all receipts.
Service under this warranty must be obtained by contacting Electrolux at the addresses or phone
numbers below.
This warranty only applies in the USA and Canada. In the USA, your appliance is warranted by Electrolux Major Appliances
North America, a division of Electrolux Home Products, Inc. In Canada, your appliance is warranted by Electrolux Canada
Corp. Electrolux authorizes no person to change or add to any obligations under this warranty. Obligations for service and
parts under this warranty must be performed by Electrolux or an authorized service company. Product features or
specifications as described or illustrated are subject to change without notice.
USA
Canada
1.800.944.9044
Electrolux Major Appliances
North America
1.800.668.4606
Electrolux Canada Corp.
5855 Terry Fox Way
P.O. Box 212378
Augusta, GA 30907
Mississauga, Ontario, Canada
L5V 3E4
8
BEFORE YOU CALL
Before calling for service, review this list. It may save you time and expense. This list includes
common occurences that are not the result of defective workmanship or materials in this appliance.
TROUBLESHOOTING
GUIDE
PROBLEM
CAUSE
CORRECTION
REFRIGERATOR OPERATION
Refrigerator does not run.
• Refrigerator is plugged into a
circuit that has a ground fault
interrupt.
• Use another circuit. If you are unsure about the outlet,have
it checked by a certified technician.
• Temperature control is in the
OFF position.
• See Setting the Temperature Control Section.
• Refrigerator may not be plugged
in, or plug may be loose.
• House fuse blown or tripped
circuit breaker.
• Ensure plug is tightly pushed into outlet.
• Check/replace fuse with a 15 amp time-delay fuse. Reset
circuit breaker.
• Power outage.
• Check house lights. Call local Electric Company.
• Room or outside weather is hot.
• It's normal for the refrigerator to work harder under these
conditions.
Refrigerator runs too much or
too long.
• Refrigerator has recently been
disconnected for a period of
time.
• It takes 4 hours for the refrigerator to cool down
completely.
• Large amounts of warm or hot
food have been stored recently.
• Doors are opened too frequently
or too long.
• Warm food will cause refrigerator to run more until the
desired temperature is reached.
• Warm air entering the refrigerator causes it to run more.
Open doors less often.
• Refrigerator door may be slightly
open.
• See "DOOR PROBLEMS" Section.
• Temperature Control is set too
low.
• Turn control knob to a warmer setting. Allow several hours
for the temperature to stabilize.
• Refrigerator gasket is dirty,
worn, cracked, or poorly fitted.
• Clean or change gasket. Leaks in the door seal will cause
refrigerator to run longer in order to maintain desired
temperature.
• Temperature Control is set too
low.
• Turn the control to a warmer setting. Allow several hours
for the temperature to stabilize.
Interior refrigerator temperature
is too cold.
• Temperature Control is set too
warm.
• Turn control to a colder setting. Allow several hours for the
temperature to stabilize.
Interior refrigerator temperature
is too warm.
• Door is kept open too long or is
opened too frequently.
• Door may not be sealing
properly.
• Warm air enters the refrigerator every time the door is
opened. Open the door less often.
• See "DOOR PROBLEMS" Section.
• Large amounts of warm or hot
food may have been stored
recently.
• Wait until the refrigerator has had a chance to reach its
selected temperature.
• Refrigerator has recently been
disconnected for a period of
time.
• Refrigerator requires 4 hours to cool down completely.
• The external refrigerator walls
can be as much as 30°F warmer
than room temperature.
• This is normal while the compressor works to transfer
heat from inside the refrigerator cabinet.
Refrigerator external surface
temperature is warm.
SOUND AND NOISE
• Modern refrigerators have
increased storage capacity and
more stable temperatures. They
require a high efficiency
compressor.
• This is normal. When the surrounding noise level is low,
you might hear the compressor running while it cools the
interior.
Louder sound levels whenever
refrigerator is on.
• Refrigerator operates at higher
pressures during the start of the
ON cycle.
• This is normal. Sound will level off or disappear as
refrigerator continues to run.
Longer sound levels when
compressor comes on.
9
BEFORE YOU CALL
PROBLEM
CAUSE
CORRECTION
SOUND AND NOISE (Cont.)
• Metal parts undergo expansion
and contraction, as in hot water
pipes.
• This is normal. Sound will level off or disappear as
refrigerator continues to run.
Popping or cracking sound
when compressor comes on.
• Refrigerant (used to cool
refrigerator) is circulating
throughout the system.
• This is normal.
Bubbling or gurgling sound,
like water boiling.
• Refrigerator is not level. It rocks
on the floor when it is moved
slightly.
• Level the unit. Refer to "Leveling" in the First Steps
Section.
Vibrating or rattling noise.
• Refrigerator is touching the wall.
• Relevel the refrigerator or move refrigerator slightly. Refer
to "Leveling" in the First Steps Section.
• Cold Control turning the
refrigerator on and off.
• This is normal.
Snapping Sound.
WATER/MOISTURE/FROST INSIDE REFRIGERATOR
• Weather is hot and humid.
• Door may not be sealing
properly.
• This is normal.
• See "DOOR PROBLEMS" Section.
Moisture forms on inside of
refrigerator walls.
• Door is kept open too long, or is
opened too frequently.
• Open the door less often.
WATER/MOISTURE/FROST OUTSIDE REFRIGERATOR
• Door may not be sealing
properly, causing the cold air
from inside the refrigerator to
meet warm moist air from
outside.
• See "DOOR PROBLEMS" Section.
Moisture forms on outside of
refrigerator.
ODOR IN REFRIGERATOR
Odors in refrigerator.
• Interior needs to be cleaned.
• Foods with strong odors are in
the refrigerator.
• Clean interior with sponge, warm water, and baking soda.
• Cover the food tightly.
DOOR PROBLEMS
Door will not close.
• Refrigerator is not level. It rocks
on the floor when it is moved
slightly.
• This condition can force the cabinet out of square and
misalign the door. Refer to "Leveling" in the First Steps
Section.
LIGHT BULB IS NOT ON
Light bulb is not on.
• Light bulb is burned out.
• Follow directions under "Interior Light"or "Mid Level Light"
in the Refrigerator Features Section.
• No electric current is reaching
the refrigerator.
• See "REFRIGERATOR OPERATION" Section.
10
|