24v driven, FTP-607 Series
2” HiGH SPeed THerMaL PrinTer
FTP-627MCL053/054
n Overview
The FTP-627 MCL Series are 24V driven high-speed printers
with a 2-inch paper width equivalent.
The FTP-627 MCL Series can be used for a variety of
applications, such as CAT/EFT, POS, banking terminals, and
measurement and medical equipment.
n HiGHLiGHTS
• Ultra compact
Height ꢀ5.5 mm, width 83.5 mm, depth 35.7 mm
FTP-627MCL053/054
• High speed printing
It can print at ꢀ00 mm/s (800 dotlines/s) maximum by using
Fujitsu's unique head drive control.
• Two types of paper routes
Front or bottom feed.
• easy paper setting
Our unique platen release mechanism allows a
wide paper route even if the printer is ultra-compact, so
paper can be easily inserted. Conventional auto loading is
also available.
FTP-627DSL238
ꢀ
FTP-627MCL053/054
n SPeCiFiCaTiOnS
Specification
Item
FTP-628MCL053
FTP-628MCL054
Interface
Conforms to RS232C / Centronics
24 VDC average current, 1.5A (2.2A peak)
(print ratio: 25%, print speed: 100mm/sec. )
For print head
Power
For motor
24 VDC 5%, 1A maximum
5 VDC 5%, 0.1 A maximum
supply
For logic
Mechanism
Interface board
Mechanism
Interface board
83.5 x 35.7 x 15.5 mm
70 x 60 x 24mm
72.3 x 34.3 x 15.5 mm
Dimensions
(WxDxH)
Approximately 49g
Approximately 25g
Approximately 47g
Weight
Life
Pulse resistance: 50 million pulses/dot (under our standard
conditions); Abrasion resistance: paper traveling distance 50km
(print ratio: 25% or less)
Head
Operating temperature*
Operating humidity
Storage temperature
Storage humidity
0˚ C to 50˚ C
20 to 85% RH (no condensation)
-20˚ C to +60˚ C (paper not included)
5 to 95% RH (no condensation)
Operating
environment
Head temperature
detection
Detected by thermistor
Detection
function
Paper out/mark detection Detected by photo-interrupter
Platen release
Detected by sliding switch
High Sensitive Paper
Standard paper:
TF50KS-E4 (Nippon Paper)
TF60KS-E(Nippon Paper),
FTP-020PU001 (58mm), PD105R
(Oji Paper), FTP-020P0701 (58mm)
Medium Life Paper
Long Life Paper
TF60KS-F1, FTP-020P0102
(58mm), PD170R (Oji Paper),
P220VBB-1 Mitsubishi Paper)
Recommended thermal sensitive paper
PD160R-N (Oji Paper),
AFB-235 (Mitsubishi Paper),
TP50KJ-R (Nippon Paper),
HA220AA (Nippon Paper)
*+5˚C to +40˚C printing density assurance rance.
3
FTP-627MCL053/054
n FUnCTiOn OF inTerFaCe bOard
Item
Item
1.
2.
3.
4.
5.
6.
7.
Test print function
8.
9.
Motor power saving function
Mark detection function
Paper out detection
Paper near end detection
Platen open detection
10. MCU operation abnormality detection
11. Power ON/OFF sequence protection
12. Motor over-current protection
13. Hardware timer
Thermal head temperature abnormality detection
Blow-out fuse detection
Head voltage abnormality detection
n diMenSiOnS
1. Printer mechanism
FTP-627MCL053
FTP-627MCL054
Unit: mm
Note: 1. Dimensions are nominal value (tolerance ±5 unless otherwise specified).
2. Platen unit (lever, platen, etc) moves by approximately 0.7mm toward paper insertion direction when platen is
open.
4
FTP-627MCL053/054
2. interface board
41.0
30
1
CN3
CN8
CN5
CN1
CN2
CN7
CN6
1
6
3
1
8
1
17.5
35.5
51.0
3.3
63.5
3.3
70.0
Unit: mm
5
FTP-627MCL053/054
1. Connector (FPC) specification (CN3)
(ꢀ) Connector
Mechanical unit side:
Remote side (housing site):
FPC connector
526ꢀ0-3090 (made by Molex)
(2) Pin assignment on the mechanical side
Signal
PHK
I/O Contents
No
1
—
—
O
—
O
—
—
—
I
Photointerrupter (Cathode)
2
VSEN
PHE
SW
SW
VH
Ground power supply for paper sensor
Photointerrupter (Emittor)
Platen open switch
3
4
5
Platen open switch
6
7
VH
Power supply for thermal head
8
VH
9
DI
Print data in
Strobe 3
10 STB3
11 VDD
12 TH
I
—
O
—
—
—
—
—
—
I
Power for logic
Thermistor
13 GND
14 GND
15 GND
16 GND
17 GND
18 GND
19 STB1
20 STB2
21 LAT
22 CLK
23 NC
Ground power supply for thermal head
Strobe 1
I
Strobe 2
I
Print data latch
Clock
I
—
—
—
—
I
Not connected
24 VH
25 VH
Power supply for thermal head
Stepping motor excitation signal
26 VH
27 MT/A
28 MT/A
29 MT/B
30 MT/B
I
I
I
6
FTP-627MCL053/054
Sensor (Photo-
interruptor)
Platen unit
Thermal head
Motor
FPC
Connect terminal:
surface side
Connector No
30,29, .....................2,ꢀ
(FPC pin numbers)
Fujitsu Components International Headquarter Offices
Japan
europe
Fujitsu Component Limited
Gotanda-Chuo Building
3-5, Higashigotanda 2-chome, Shinagawa-ku
Tokyo ꢀ4ꢀ, Japan
Fujitsu Components Europe B.V.
Diamantlaan 25
2ꢀ32 WV Hoofddorp
Netherlands
Tel: (8ꢀ-3) 5449-70ꢀ0
Tel: (3ꢀ-23) 55609ꢀ0
Fax: (8ꢀ-3) 5449-2626
Fax: (3ꢀ-23) 5560950
Email: [email protected]
Email: [email protected]
north and South america
Asia Pacific
Fujitsu Components America, Inc.
250 E. Caribbean Drive
Sunnyvale, CA 94089 U.S.A.
Tel: (ꢀ-408) 745-4900
Fujitsu Components Asia Ltd.
ꢀ02E Pasir Panjang Road
#04-0ꢀ Citilink Warehouse Complex
Singapore ꢀꢀ8529
Fax: (ꢀ-408) 745-4970
Tel: (65) 6375-8560
Email: [email protected]
Fax: (65) 6273-302ꢀ
Email: [email protected]
©2006 Fujitsu Components America, Inc. All rights reserved. All trademarks or registered trademarks are the property off their respective
owners.
Fujitsu Components America does not warrant that the content of datasheet is error free. In a continuing effort to improve our products Fujitsu
Components America, Inc. reserves the right to change specifications/datasheets without prior notice. Rev. 01/26/2006.
7
|