Fujitsu Printer FTP 628 Series User Manual

BATTERY DRIVE, 2” HIGH SPEED THERMAL PRINTER  
FTP-628 Series  
OVERVIEW  
The FTP-628 MCL Series is ultra compact high speed, battery  
driven thermal printer, printing on 2-inch wide paper (58mm).  
Paper can be easily set by an original platen release mecha-  
nism.  
The FTP-628 MCL series can be used for a variety of  
applications, such as portable terminals, POS, ticket issuing  
terminals, label printers, banking terminals, and measurement  
and medical equipment.  
HIGHLIGHTS  
• Ultra compact  
Height 15.5 mm, width 69.9 mm, depth 35.7 mm  
• High speed printing  
It can print at 60 mm/s (480 dotlines/s) maximum by using  
Fujitsu's unique head drive control.  
• High resolution printing / Kanji supported  
8 dots/mm of resolution printing is possible.  
• Easy paper setting  
Our unique platen release mechanism allows a  
wide paper route even if the printer is ultra-compact, so  
paper can be easily inserted. Auto loading is also available  
on the MCL001 and MCL003 models.  
• Two types of paper routes  
Front and bottom paper feed.  
• Easy mounting  
Head, motor, sensor and other component wiring are unified  
to one flexible cable, and the mechanism can be secured by  
one hook and two screws at two locations, making mounting  
easy.  
1
 
FTP-628MCL Series  
SPECIFICATIONS  
Item  
Specification  
Interface  
Conforms to RS232C / Centronics  
4.2 - 8.5 VDC average current, 0.79 (1.3) A (print ratio:  
12.5%, print speed: 60mm/sec.) ( ) is the peak value  
For print head  
Power  
For printer and cutter motor 4.2 - 8.5 VDC, 1A maximum  
supply  
For logic  
5 VDC ± 5%, 0.5 A maximum  
69.6 x 34.3 x 15.5 mm (WxDxH) head down  
131 x 99 x 24 mm  
Printer mechanism  
Interface board  
Dimensions  
Weight (Mechanism)  
Head life  
Approximately 53g (without knob)  
Pulse resistance: 100 million pulses/dot (under our  
standard conditions)  
Abrasion resistance: paper traveling distance 50km  
(print ratio: 25% or less)  
+5˚ C to +40˚ C (printing density assurance range,  
operation is possible at 0˚ C to +40˚ C)  
Operating temperature  
Operating  
environment  
Operating humidity  
Storage temperature  
Storage humidity  
20 to 85% RH (no condensation)  
-20˚ C to +60˚ C (paper not included)  
5-95% RH (no condensation)  
Head temperature  
detection  
Detected by thermistor  
Detection  
function  
Paper out/mark detection  
Head up detection  
Detected by photo-interrupter (all models)  
Detected by micro-switch (003, 004 only)  
High sensitive paper: TF50KS-E4 (Nippon Paper)  
Standard paper:  
TF60KS-E (Nippon Paper) -  
FTP-020PU001/ FTP-020P0104  
PD150R (Oji Paper) -  
FTP-020P0701  
Medium life storage paper:  
TF60KS-F1 (Nippon Paper) -  
Recommended thermal sensitive paper  
FTP-020P0102  
PD170R (Oji Paper)  
P220VBB-1 (Mitsubishi Paper)  
PH65BC-3H (Oji Paper)  
Long life storage paper:  
PD160R-N (Oji Paper)  
AFP-235 (Mitsubishi Paper)  
3
 
FTP-628MCL Series  
FUNCTION  
Item  
Item  
1.  
2.  
3.  
4.  
Test print function  
8.  
9.  
Cutter abnormality detection  
Motor power saving function  
Paper out detection  
Paper near end detection  
Head up detection  
10. Mark detection function  
11. MCU operation abnormality detection  
Thermal head temperature abnormality  
detection  
5.  
12. Power ON/OFF sequence protection  
6.  
7.  
Blow-out fuse detection  
13. Motor over-current protection  
14. Hardware timer  
Head voltage abnormality detection  
DIMENSIONS  
1. Printer mechanism  
Platen Open  
Platen Close  
Paper Insertions  
Platen Open  
Center of Paper  
Platen Close  
Paper Insertion  
Center of Paper  
15.5  
Note: 1. Dimensions are nominal value (tolerance ±5 unless otherwise specified).  
2. Platen unit (lever, platen, etc) moves by approximately 0.7mm toward paper insertion direction when platen is  
open.  
4
 
FTP-628MCL Series  
2. Interface board  
130.8  
83.8  
55.9  
6.4  
4 - ø 3.6±0.1  
CN1  
CN6*  
CN3  
5.1  
CN2  
30.5  
CN7  
CN8**  
91.4  
5.1  
120.7  
Part mounting side  
Part solder side  
* CN6 not used  
** CN8 used for paper near end detection  
Unit: mm  
5
 
FTP-628MCL Series  
PRINTER CONNECTOR (FLEXIBLE PT BOARD) PIN ARRAYS  
Control circuit side connector: 52030-3010 Molex or equivalent product (Reference CN3)  
No.  
1
Signal  
PHK  
I/O  
Contents  
Photo interrupter (cathode)  
Photo interrupter (emitter)  
Head driving power supply  
Ground for head  
Data latch  
No.  
2
Signal  
VSEN  
I/O  
Contents  
Power supply for paper sensor  
Head driving power supply  
Ground for head  
Data input  
O
I
I
I
3
PHE  
VH  
4
VH  
5
6
GNC  
DIN  
I
7
GND  
LAT  
I
8
9
10  
12  
14  
16  
18  
20  
22  
24  
26  
28  
CLK  
STB5  
VDD  
STB 2  
TH  
I
Clock  
11  
13  
15  
17  
19  
21  
23  
25  
27  
STB6  
STB4  
STB3  
STB1  
TH  
I
Enable 6  
I
Enable 5  
I
Enable 4  
I
Logic Power supply  
Enable 2  
I
Enable 3  
I
I
Enable 1  
O
I
Thermistor  
O
I
Thermistor  
GND  
VH  
Ground for head  
Head driving power supply  
Open terminal  
GND  
VH  
Ground for head  
Head driving power supply  
Head open switch*  
N.C.  
SW2  
MT/B  
O
I
SW1  
MT/B  
I
Head open switch*  
I
Stepping motor coil  
excitation signal B  
Stepping motor coil  
excitation signal B  
29  
MT/A  
I
Stepping motor coil  
excitation signal A  
30  
MT/A  
I
Stepping motor coil  
excitation signal A  
* on MCL003 and MCL004 models  
6
 
FTP-628MCL Series  
INTERFACE  
1. Centronics interface  
(1) Connector (CN2)  
Connector part number  
: FCN-605Q030-G/M (Fujitsu Components) or equivalent  
Mating connector part number : FCN-607B030-G/B (Fujitsu Components) or equivalent  
(2) Connector pin assignment  
No.  
1
Signal  
PRSTB  
I/O  
Contents  
Data strobe  
No.  
2
Signal  
I/O  
I
Contents  
I
I
PRSTB-RET  
PRDT0-RET  
PRDT1-RET  
PRDT2-RET  
PRDT3-RET  
PRDT4-RET  
PRDT5-RET  
PRDT6-RET  
PRDT7-RET  
ACKNLG-RET  
BUSY-RET  
INPRM-RET  
INPRM  
Connected to logic GND  
Connected to logic GND  
Connected to logic GND  
Connected to logic GND  
Connected to logic GND  
Connected to logic GND  
Connected to logic GND  
Connected to logic GND  
Connected to logic GND  
Connected to logic GND  
Connected to logic GND  
Connected to logic GND  
Reset  
3
PRDT0  
PRDT1  
PRDT2  
PRDT3  
PRDT4  
PRDT5  
PRDT6  
PRDT7  
ACKNLG  
BUSY  
Data 0  
4
5
I
Data 1  
6
7
I
Data 2  
8
9
I
Data 3  
10  
12  
14  
16  
18  
20  
22  
24  
26  
28  
30  
11  
13  
15  
17  
19  
21  
23  
25  
I
Data 4  
I
Data 5  
I
Data 6  
I
Data 7  
O
O
O
I
Data input acknowledge  
Busy  
RINF2  
SLCTIN  
RINF1  
ATF  
Printer status 2  
Printer select  
Printer status 1  
Paper feed request  
27  
29  
O
I
RINF3  
O
Printer status 3  
GND  
Logic GND  
Notes:  
• Symbol ” means a negative logic signal.  
• “–RET” signal is a return signal of the twisted pair cable.  
• “I” or “O” means a signal direction from the interface board side.  
(3) Connector pin number  
(4) Data input signal timing  
FCN-605Q030-G/M (Fujitsu Components)  
PRDT0~7  
t1  
t3  
PRSTB  
BUSY  
t2  
No.1  
t4  
ACKNLG  
t5  
No.30  
No.2  
Data set time  
PRSTB pulse width  
Data hold time  
PRSTB to BUSY= “H”  
ACKNLG pulse time  
:t10.5 µsec  
:t20.5 µsec  
:t30.5 µsec  
:t40.5 µsec  
:t55.0 µsec  
7
 
FTP-628MCL Series  
(5) Printer status signals  
Error status  
RINF1  
Low  
RINF2  
High  
High  
Low  
RINF3  
Low  
1. Paper out  
2. Paper near end  
High  
High  
High  
Low  
Low  
3. Head up  
Low  
4. Head temperature abnormality  
5. Head voltage abnormality  
6. Hardware abnormality  
7. Mark detection abnormality  
8. Normal  
Low  
High  
High  
High  
Low  
High  
High  
Low  
High  
Low  
Low  
Low  
High  
2. RS-232C  
(1) Connector (CN7)  
Connector part number  
: B10B-PH-K-S (J.S.T.) or equivalent  
Mating connector part number : PHR-10 (J.S.T.) or equivalent  
(2) Connector pin assignment  
No.  
1
Signal  
FG  
I/O  
-
Contents No.  
Frame ground  
No.  
2
Signal  
RD  
I/O  
Contents No.  
I
O
I
Receive data  
3
TD  
O
-
Transmission data  
Signal ground  
4
DTR  
DSR  
Data terminal ready  
Data set ready  
5
GND  
6
7
9
SLCTIN  
ATF  
I
I
Printer select  
8
INPRM  
I
I
Reset  
Power down cancellation  
signal  
Paper feed request  
10 PWD  
Notes:  
• Symbol ” means a negative logic signal.  
• “I” or “O” means a signal direction from the interface board side.  
8
 
FTP-628MCL Series  
CONNECTOR PIN ASSIGNMENT  
1. Connector for power supply (CN1)  
Part number  
: B6P-VH (J.S.T) or equivalent (board side)  
Mating Connector  
: VHR-6N  
No.  
Signal  
+V5  
I/O  
Contents No.  
No.  
2
Signal  
GND  
I/O  
Contents No.  
1
3
5
-
-
-
Power supply for logic  
Ground  
-
-
-
Ground  
Ground  
GND  
+VH  
4
GND  
+VH  
Power supply for head motor  
6
Power supply for head motor  
2. Connector for printer mechanism connection (CN3)  
Part number  
: 52030-3010 (made by Molex) or equivalent (board side)  
No.  
Signal  
PHK  
I/O  
I
Contents  
Photo interrupter (cathode)  
Photo interrupter (emitter)  
Head driving power supply  
Ground for head  
Data latch  
No.  
2
Signal  
VSEN  
I/O  
O
O
O
O
O
O
O
I
Contents  
Power supply for paper senor  
Head driving power supply  
Ground for head  
Data input  
1
3
PHE  
VH  
4
VH  
5
O
O
O
O
O
O
I
6
GNC  
DIN  
7
GND  
LAT  
8
9
10  
12  
14  
16  
18  
20  
22  
24  
26  
28  
CLK  
STB5  
VDD  
STB 2  
TH  
Clock  
11  
13  
15  
17  
19  
21  
23  
25  
27  
STB6  
STB4  
STB3  
STB1  
TH  
Enable 6  
Enable 5  
Enable 4  
Logic Power supply  
Enable 2  
Enable 3  
Enable 1  
Thermistor  
Thermistor  
GND  
VH  
O
I
Ground for head  
Head driving power supply  
Open terminal  
GND  
VH  
O
O
O
Ground for head  
Head driving power supply  
Head open switch*  
N.C.  
SW2  
MT/B  
SW1  
MT/B  
Head open switch*  
Stepping motor coil  
excitation signal B  
O
Stepping motor coil  
excitation signal B  
29  
MT/A  
O
Stepping motor coil  
excitation signal A  
30  
MT/A  
O
Stepping motor coil  
excitation signal A  
* on MCL003 and MCL004 models  
9
 
FTP-628MCL Series  
OPTIONS  
Name  
Part Number  
Length (mm)  
500  
Interface Cable  
(between board and  
equipment)  
For Centronics (CN2) FTP-441Y201  
For RS232C (CN7)  
FTP-628Y301  
FTP-622Y401  
500  
300  
Power supply cable (CN1)  
Near end paper sensor (CN8) if required  
10  
 
FTP-628MCL Series  
COMMANDS  
Command  
Contents  
Moves print position to the next tab.  
Line feed.  
HT  
LF  
FF  
Feeds forms (new page).  
Power down.  
DC 2  
ECS RS  
Sets reverse printing.  
Resets reverse printing.  
Sets print mode.  
ESC US  
ESC ! + n  
ESC %+n  
ESC &+y+c1+c2+x+d1~dN  
ESC *+m+n1+n2+d1~dN  
ESC ?+n  
ESC 2  
Download character set specification//cancellation.  
Download character definition.  
Sets bit image mode.  
External registration character deletion.  
Sets 1/6 inch line feed length.  
Sets the line feed length.  
ESC 3+n  
ESC @  
Printer initialization.  
ESC A+n  
ESC C+n  
ESC D+d1~dN+NUL  
ESC J+n  
ESC K+n  
ESC R+n  
ESC c+1+n  
ESC d+n  
ESC e+n  
ECS s+n  
ECS t+n  
ESC {+n  
FS !+n  
Sets the space between the line.  
Sets the page length by character line.  
Sets the tab position.  
Feeds paper in forward direction and prints.  
Reverse paper feed.  
Selects international character.  
Sets internal processing (including auto paper loading).  
Printing and n-line feeding.  
Prints and reverse feeds n-lines.  
Sets printing speed.  
Character code table selection.  
Sets/resets upside down printing.  
Kanji printing mode collective specification.  
Kanji printing mode specification.  
Kanji printing mode cancellation.  
Sets the detection functions.  
FS &  
FS .  
FS 9+n  
11  
 
FTP-628MCL Series  
Commands continued  
Command  
Contents  
FS C+n  
Kanji code system selection.  
FS W+n  
Kanji double height and width mode specification/cancellation.  
Line feeds to the next mark.  
GS <  
GS A+m+n  
GS E+n  
Sets the line feed length after mark detection.  
Sets print quality.  
GS V+n+m  
GS e+n+m  
GS h+n  
Paper cutting (for pending cutter models only).  
Sets bar code width.  
Sets bar code height.  
GS k+m+n+d1~dN  
GS w+n  
Selects bar code type and prints.  
Sets bar code width magnification.  
FS *+m+n1+n2+d1~dN  
GS &+m+x+y1+y2+d1~dN  
GS '+m+n  
FS E+n  
High speed collective image printing specified.  
Registration of image data.  
Prints registered image data.  
Correction of impressed energy.  
ESC V+n  
Right Rotation 90° specification / cancellation.  
Sets and cancels status transmission. (Serial Mode)  
Parameter transmission. (Serial Mode)  
Setting the amount of the feeding at automatic paper load.  
Setting the turning time of the motor excitation.  
Deletes recorded contents in flash memory.  
GS a+n  
FS r+n  
ESC EM+n  
ECS X+n+m  
ESC DEL+n  
Europe  
Japan  
Fujitsu Components Europe B.V.  
Diamantlaan 25  
2132 WV Hoofddorp  
Netherlands  
Fujitsu Component Limited  
Gotanda-Chuo Building  
3-5, Higashigotanda 2-chome, Shinagawa-ku  
Tokyo 141, Japan  
Fujitsu Components  
International  
Headquarter  
Offices  
Tel: (31-23) 5560910  
Fax: (31-23) 5560950  
Tel: (81-3) 5449-7010  
Fax: (81-3) 5449-2626  
Asia Pacific  
North and South America  
Fujitsu Components America, Inc.  
250 E. Caribbean Drive  
Sunnyvale, CA 94089 U.S.A.  
Tel: (1-408) 745-4900  
Fujitsu Components Asia Ltd.  
102E Pasir Panjang Road  
#04-01 Citilink Warehouse Complex  
Singapore 118529  
Tel: (65) 6375-8560  
Fax: (1-408) 745-4970  
Fax: (65) 6273-3021  
© 2003 Fujitsu Components America, Inc. All company and product names are trademarks or registered  
trademarks of their respective owners. Rev. 04/03/2003  
12  
 

EverFocus Car Stereo System EDR410H User Manual
Fisher Price Baby Toy B9760 User Manual
Fostex Musical Instrument VF160EX User Manual
Frigidaire Ice Maker 242292000 User Manual
Fujitsu Server TX200FT S2 User Manual
FUNAI CRT Television EC520E User Manual
Gas Fired Products Electric Heater PTS User Manual
GE Conference Phone 28128 User Manual
GE Thermostat CC SCSTAT User Manual
Goodman Mfg Air Cleaner GDMHEPA User Manual