24V DRIVE, ULTRA HIGH SPEED LINE THERMAL PRINTER
3” MECHANISM, WITH CUTTER
FTP-632MCL301/302
■ OVERVIEW
FTP-632MCL/FTP-622DCL/DSL Series is an ultra high speed
line thermal printer driven by 24 VDC, printing on 3-inch wide
paper (80 mm/85 mm).
This printer is compact and light weight, and the design allows
easy head maintenance, head cleaning and head replacement.
This printer is suitable for a variety of applications, such as POS
terminals, ticket machines, coupon machines, label printers,
medical instruments, etc. A printer with a specially designed
cutter is also available.
FTP-632MCL301
■ HIGHLIGHTS
• Ultra high speed printing
It can print at 80 mm/s (640 dotlines/s) maximum by using
Fujitsu Components' unique head drive control.
• Compact and lightweight
This printer has a low profile of only 20 mm, and a light
weight of approximately 94 g.
• Low power consumption
The peak current for head driving is approximately 2.9 A (at
80 mm/s printing speed, 50% printing ratio).
FTP-622CU101
• Easy head access
It is designed for easy head cleaning and head replacement.
• Paper auto loading function
Thermal paper can be loaded without head-up lever
operation.
• ESC/POSTM*1 Commands
The commands conform to ESC/POSTM.
• Auto Cutter
Printer with auto cutter (full cut/partial cut) is also available.
• UL Recognized
File No.E171434
*1 ESC/POSTM is a registered trademark of SEIKO EPSON Corp.
FTP-622DCL011
FTP-632MCL301/302
(Continued)
Item
Specifications
Part number
Interface
FTP-632MCL301/302
Centronics (ESC/POSTM), RS232C
24 VDC ± 5%, Voltage
2
Current : average*
(
): Peak
For head
1.11 (1.45) A (at 80 mm/s printing speed, 25% printing ratio)
0.81 (1.45) A (at 50 mm/s printing speed, 25% printing ratio)
0.75 (0.87) A (at 30 mm/s printing speed, 25% printing ratio)
Power supply
For motor
24 VDC ± 5%, 1.0 A maximum
24VDC ± 5%, 1.0 A maximum
5 VDC ± 5%, 0.5 A maximum
123 (W) × 70 (D) × 42 (H) mm (w/cutter)
131 (W) × 89 (D) × 24 (H) mm
approximately 380 g (w/cutter)
For cutter
For logic
Mechanism (cutter)
Interface board
Dimensions
Weight (Mechanism+Cutter)
Mechanism
Pulse durability : 1 × 108 pulse/dot (using Fujitsu's standard
driving method)
Wear resistance : 50 km (at 25% printing ratio)
Expected life
Cutter
3 × 105 cuts
3
Operating temperature 0 to +50°C*
Environmental
conditions
Operating humidity
Storage temperature
Storage humidity
Head temperature
Paper out/Mark detect
Head-up
20 to 85% RH (no condensation)
–20 to +60°C (excluding paper)
5 to 95% RH (no condensation)
By thermistor (applied energy control, abnormal temperature detection)
By photointerrupter
Detection
By microswitch
For front insertion use (80 mm width)
For rear insertion use (85 mm width)
*Recommended papers
· Oji Paper
· NIPPON Paper
· MITSUBISHI Paper Mills
: FTP-030PU001, FTP-030P0701
: FTP-030P0020, FTP-030P0702
Recommended thermal sensitive paper
: PD150R, PD160R, PD170R
: TF50KS-E,TF60KS-E,TF60KJ-R
: P220VBB-1, AFP-235
*1: There may be exceptions.
*2: 24 VDC, minimum head resistance.
*3: Guarantee: +5°C ~+40°C.
3
FTP-632MCL301/302
Mechanism with cutter
3—M 3(FIXING HOLE FROM UPPER SIDE)
MCL301
MCL302
15
±
300
2—M 3 burring (FIXING HOLE FROM BOTTOM SIDE)
63.4
76.8(POSITIONING H0LE)
58.2
117.5
57±1
(60.5)
(78.6)
Note: all dimensions are nominal value.
Unit: mm
4
FTP-632MCL301/302
Interface board
130.8
120.7
116.8
87.6
19.1
5.1
5.1
CN2**
CN5
CN3
4—ø3.6
CN10
CN11*
CN13
5.1
5.1
43.2
86.4
105.4
120.7
*CN11 on FTP-622DCL011/111 & 622DSL011/012/112 only
**CN2 on FTP- 622DSL only
Unit: mm
■ FUNCTION
ITEM
ITEM
1.
2.
3.
4.
5.
6.
7.
Test printing
Paper-out detection
8.
9.
Cutter trouble detection
Motor power save
Paper near end detection
Head-up detection
10.
11.
12.
13.
14.
Mark detection
MCU trouble detection
Power on/off sequence protection
Motor protection
Abnormal temperature detection of thermal head
Blown fuse detection
Abnormal voltage detection of head
Hardware timer
■ INTERFACE, COMMAND, OPTIONS
Please refer to the FTP-622DCL DATA SHEET and the FTP-622DSL DATA SHEET for Interface, Command, and
Options.
5
FTP-632MCL301/302
Europe
Japan
Fujitsu Components Europe B.V.
Diamantlaan 25
2132 WV Hoofddorp
Netherlands
Fujitsu Component Limited
Gotanda-Chuo Building
3-5, Higashigotanda 2-chome, Shinagawa-ku
Tokyo 141, Japan
Fujitsu Components
International
Headquarter
Offices
Tel: (31-23) 5560910
Fax: (31-23) 5560950
Email: [email protected]
Tel: (81-3) 5449-7010
Fax: (81-3) 5449-2626
Email: [email protected]
Asia Pacific
North and South America
Fujitsu Components America, Inc.
250 E. Caribbean Drive
Sunnyvale, CA 94089 U.S.A.
Tel: (1-408) 745-4900
Fujitsu Components Asia Ltd.
102E Pasir Panjang Road
#04-01 Citilink Warehouse Complex
Singapore 118529
Tel: (65) 375-8560
Fax: (1-408) 745-4970
Fax: (65) 273-3021
Email: [email protected]
Email: [email protected]
© 2001 Fujitsu Components America, Inc. All company and product names are trademarks or registered
trademarks of their respective owners. Rev. 09/2001
6
|