INSTALLATION, MAINTENANCE AND USE
INSTRUCTIONS FOR
FREE-STANDING COOKERS
60x60 cm (type M6)
READ THE INSTRUCTION BOOKLET BEFORE INSTALLING AND USING
THE APPLIANCE.
The manufacturer will not be responsible for any damage to property or to persons
caused by incorrect installation or improper use of the appliance.
The manufacturer is not responsible for any inaccuracies, due to printing or transcription
errors, contained in this booklet. In addition, the appearance of the figures reported is also
purely indicative.
The manufacturer reserves the right to make changes to its products when considered
necessary and useful, without affecting the essential safety and operating characteristics.
BACKGUARD INSTALLATION INSTRUCTION
1) Remove n°2 screws fixing worktop as shown in fig.4
2) Place front part of the backguard and attach it from bottom side with the two removed screws (point 2) as shown in
fig .5
3) Fix the front part of the backguard with the screws supplied with the backguard kit (fig.6)
4) Assemble back part with front part of the backguard and fix them with a screws supplied with the backguard kit
(fig.7)
APPLIANCE ELECTRIC CONNECTION:
The electric connection must comply with the current legal standards and regulations.
Before making the connection, check that:
- The system electrical rating and the current outlets are adequate for the maximum power output of the appliance (see
the label applied to the bottom of the casing).
- The outlet or the system is equipped with an efficient ground connection in accordance with the current legal standards
and regulations. The company will not be responsible for the non-compliance with these instructions.
When the connection to the power supply network is made using an outlet:
- If the power cord is supplied without a plug, apply a standard plug that is suitable for the load indicated on the label.
Connect the wires according to the diagram shown in FIG.8 and check that:
letter L (phase) = brown wire;
letter N (neutral) = blue wire;
ground symbol
= green-yellow wire;
- The power cord must be positioned so that an overtemperature of 75 K will not be reached at any point.
- Do not use reductions, adapters or splitters since they might cause false contacts and lead to dangerous overheating.
When the connection is made directly to the electric network:
- Use a device that ensures disconnection from the mains in which the contacts are opened to a distance that permits
complete disconnection according to the conditions for over-voltage category III.
- Remember that the ground wire must not be interrupted by the circuit-breaker.
- As an alternative, the electric connection can also be protected by a high-sensitivity residual current circuit-breaker.
- It is highly recommended to attach the special green-yellow ground wire to an efficient ground system.
WARNING: If the power cord is replaced, the ground wire (yellow-green) connected to the terminal, should be
longer than the other wires by about 2 cm.
TYPES OF POWER CORDS
The appliance is equipped with a terminal for the electric connection placed behind, which is accessible removing the
posterior casing (Fig.9)
The cable of alimentation can be :
Operation at 220-240V~ : use a H05BB-F three-wire cable (cable 3x4 mm²)
Operation at 380-415V2N~ : use a H05RR-F o H07RN-F four-wire cable (cable 4x4 mm²)
Operation at 380-415V3N~ : use a H05RR-F o H07RN-F five-wire cable (cable 5x1,5 mm²)
Fig.10
The power supply cable is suitable for appliance operating on 220-240 V~
ATTENTION: The appliance conforms with the regulations of directives 2009/142/CE(ex 90/396/EC) (Gas
Directive) regarding gas appliances for domestic use and the like, 2006/95/CE (Low Voltage Directive) regarding
electrical safety and 2004/108/CE, (EMC Directive) regarding electromagnetic compatibility.
Electrical requirements
220-240V~ - 10000W( induction 7100W) (45 A max)
380-415V2N~ 10000W( induction 7100W) (32 A max/phase).
380-415V3N~ 10000W( induction 7100W) (16 A max/phase).
3
APPLIANCE MAINTENANCE
ATTENTION: IMPORTANT WARNINGS
For cookers resting on a base
ATTENTION: If the cooker rests on a base, take the measures necessary to prevent the cooker from sliding along the
support base.
For cookers with glass covers
ATTENTION: Before opening the appliance’s glass cover, carefully remove all liquid residues from the top of it.
ATTENTION: Before closing the appliance’s glass cover, make sure that the work surface has cooled.
For cookers with electric ovens
The unit becomes hot during use. Do not touch the heating elements inside the oven.
For cookers with electric ovens
ATTENTION: The accessible parts can become hot during use. Keep children away from the appliance.
For the food warmer compartment (or drop leaf in our case)
ATTENTION: The internal parts of the food warmer can become hot during use.
For glass doors
Do not use abrasive cleaning products or metal spatulas with sharp edges to clean the oven door’s glass since this could
scratch the surface and the glass could break.
Do not use steam cleaners to clean the appliance.
REPLACING PARTS
Before performing any maintenance operation, disconnect the appliance from the gas supply and electricity
network.
To replace parts such as knobs and burners, just remove them from the seats without disassembling any part of the
cooker.
To replace parts such as nozzle supports, valves and electric components follow the procedure described in the burner
adjustment paragraph. To replace the valve or the gas thermostat, it is also necessary to disassemble the two rear gas
train brackets, loosening the 4 screws (2 per bracket) that attach it to the rest of the cooker and, unscrew the nuts that
attach the front burner valves to the control support, after removing all the knobs. To replace the gas or electric
thermostat, also disassemble the rear cooker guard, loosening the relative screws, to be able to pull out and reposition
the thermostat bulb.
To replace the oven bulb, just unscrew the protection cap that projects out inside the oven. (Fig.11)
WARNING: Before replacing the bulb, disconnect the appliance from the electric power supply.
WARNING: The power cord supplied with the appliance is connected to that appliance with an X type connection (in
compliance with standards EN 60335-1, EN 60335-2-6 and subsequent amendments) for which it can be installed
without the use of special tools, with the same type of cord as the one installed.
If the power cord becomes worn or damaged, replace it based on the information reported in table 3 .
WARNING: If the power cord is replaced, the installer shall ensure that the ground cable is longer than the
phase cables and also shall comply with the warnings regarding the electric connection.
To replace the power cable, lift the terminal board’s cover and replace the cable. To access the terminal board in cookers
with a 3x2.5mm² cable, the back panel on the rear of the appliance must be removed.
USE AND MAINTENANCE MANUAL
CONTROL PANEL DESCRIPTION
On the control panel, small symbols show the function of each knob or key. Here as follows are the several controls that
a cooker can have:
the symbol
shows the disposition of induction zone on the worktop, the full dot identifies the zone in object (in
this case the central zone).
the symbol
shows the running of any left oven ( 9 positions switch)
shows the electric thermostat for electric left oven
the symbol
4
USING THE INDUCTION HOB
HOB CONTROL KNOB
These knobs provide control of the ceramic hob's cooking zones.
The zone it controls is shown above eachknob. Turn the knob to the right to set the zone's operating power; the settings
range from a minimum of 1 to a maximum of 9. (fig.12)
The working power is shown by a display on the hob.
Heating accelerator
Each cooking zone is equipped with a heating accelerator.
This system allows the zone to be operated at peak power for a time proportional to the heating power selected.
To start the heating accelerator, turn the knob to the left, select setting "A" and then release. The letter "A" will appear on
the display on the hob.
You now have 3 seconds to select the heating setting of your choice. Once a setting between 1 and 9 has been selected,
"A" and the chosen setting will flash in alternation on the display. '
While the heating accelerator is in operation, the heating level can be increased at any time. The "full power" time will be
modified accordingly. If the power is reduced by turning the knob anticlockwise, option "A" is automatically deactivated.
Power Function
The power function allows the user to operate each heating zone continuously at the maximum power for a time of no
more than 10 minutes. This function can be used, for example, to bring a large amount of water to the boil in a hurry, or
to turn up the heat under meat.
Turn the knob clockwise and set heating level 9, then use the knob to set the "P" position and release il. "P" appears on
the corresponding zone display.
After 10 minutes, the power is reduced automatically, the knob returns to the 9 setting and the "P" disappears.
However, the power function can be turned ott at any time by reducing the heating level. .
When the power function is selected for one heating zone (e.g. the left front zone), the power absorbed by the second
zone (Ieft rear zone) might be reduced to supply the maximum available energy to the first zone.
Consequently, the power function takes priority over the heating accelerator.
If a pan is removed from the cooking zone while the power function is on, the function is switched off.
Holding Function
The holding function keeps the temperature of the bottoms of pans at about 42°C or 70°C . This allows foods to be kept
hot with optimal energy consumption and to be heated gently. The holding function can be kept in operation for up to 2
hours.
The holding function is
and is indicated by the relevant symbols on the cooking zones.
Bridge Function
This function allows to use the 2 cooking zones at the right at same time with the same features as a single cooking
zone. Booster function isn’t allowed.
1 – rotate both knobs, rear right and front right, at the same time in the P position and keep the knobs in that position.
2 – we see that the ∏ symbol blinks in the display, then after a few seconds the ∏ symbol appears on the rear right
display and the front right display shows the power level.
3 – to control the bridge power level use the knob 4 (front right zone). If you turn the knob 3 (rear right zone) the display
shows a horizontal segment and the bridge function ends.
HOB
ATTENTION:
Metal items such as cutlery or lids must never be placed on the surface of the hob since they may become hot.
Cooking zones (fig.13)
The appliance is equipped with 4 cooking zones having different diameters and powers. Their positions are clearly
marked by rings, while the heating power is only released in the area shown on the ceramic hob. The 4 cooking zones
are of HIGH-LlGHT type and start to heat up a few seconds after they are switched on. The heat level of each zone can
be regulated from the minimum to the maximum setting using the knobs on the front panel.
Underneath each cooking zone there is a coil called an inductor, supplied with power by an electronic system, which
generates a variable magnetic field. When a pan is placed inside this magnetic field, the highfrequency currents
concentrate directly on the bottom of the pan and produce the heat needed to cook the foods.
The 4 lights between the cooking zones come on when the temperature of one or more cooking zones exceeds 60° C..
The lights go out when the temperature drops to below about 60° C.
5
Zone number:
Zone diameter:
Power absorption
Normal operation:
With power function:
3700W
1
2
3
4
210 mm
180 mm
180 mm
180 mm
2300W
1850W
1850W
1850W
3000W
3000W
3000W
When the hob is used for the first time, it should be heated to its maximum temperature for long enough to bum off
any oily residues left by the manufacturing process, which might contaminate foods with unpleasant smells.
TYPES OF PANS
This type of appliance can only operate with pans of special kinds.
The bottom of the pan must be iron or steel/iron to generate the magnetic field necessary for the heating processo
Vessels made from the following materials are not suitable:
glass;
porcelain;
pottery;
steel, aluminium or copper without magnetic bottom;
To check that a pan is suitable, simply piace a magnet close to its bottom:
if the magnet is attracted, the pan is suitable for induction cooking. If no magnet is to hand, put a little water in the pan,
piace it on a cooking zone and switch it on. If the symbol appears on the display instead of the power, the pan is not
suitable.
The pans used for cooking must have certain minimum diameters to ensure satisfactory operation.
Pans larger than the cooking zones can also be used, but it is important to ensure that the bottom of the pan does not
touch other cooking zones, and that it is always centred over the perimeter of the cooking zone.(fig.14-15)
Zone number
Pan minimum diameter
90 mm
1
2
3
4
5
140 mm
110 mm
140 mm
90 mm
Use only vessels specially designed for induction cooking, with thick, completely flat bottom; if these are not available,
the pans used must not have crowned (concave or convex) bottom. (fig.16)
Pan present device
Each cooking zone is equipped with a "pan present" device, which ensures that cooking cannot start unless a suitable
pan is present on the cooking zone and properly positioned.
If the user attempts to switch on the cooking zone with the pan not positioned properly or with a pan which is not of
suitable material, a few seconds after the zone is switched on the
has been made.
symbol will appear to warn the user that an error
Residual heat
Each cooking zone is equipped with a device which warns of residual heat. After any cooking zone is switched off, a
flashing ‘H’ may appear on the display. This warns that the cooking zone concerned is stili very hot. Cooking can be
restarted while the ‘H’ is flashing; proceed as described in point "3".
Locking-out the hob
When not in use, the hob can be "locked out" to prevent children from accidentally switching it on.
With the cooking zones off, turn the knobs of zones 1 and 2 to the left simultaneously until ‘’L’’ appear on the power
display and then release the knobs.
To deactivate it, repeat the same procedure: the cooking zone displays will stop displaying the ‘’L’’, indicating that the
cooking zone lock-out function has been deactivated.
Attention:
Take care not to spill sugar or sweet mixtures onto the hob during cooking, or to piace materials or substances which
might melt (plastic or aluminium foil) on it; if this should occur, to avoid damage to the surface, tum the heating off
immediately and clean with the scraper supplied while the cooking zone is stili warm. If the ceramic hob is not cleaned
immediately, residues may form which cannot be removed once the hob has cooled.
Important!
Keep a close eye on children because they are unlikely to see the residual heat waming lights. The cooking zones are
stili very hot for some time after use, even if they are switched off. Make sure that children never touch them.
6
WARNING: Under no circumstance use aluminium foil or plastic containers to hold the food while cooking on a glass-
ceramic hob.
WARNING: Do not touch the cooking area as long as the light indicating residual heat on the glass-ceramic hob, is “on”;
this indicates that the temperature in the relative area is still high.
WARNING: Never place pan with bottoms which are not perfectly flat and smooth on the hob
WARNING: If you notice a crack in the ceramic hob, disconnect the appliance from the elettricity supply and contact a
service centre
WARNING: Your glass-ceramic hob is thermal shock resistant and resistant to both heat and cold.
If you drop a heavy pot on your hob it will not break.
On the contrary, if a hard object, such as the salt shaker or the spice bottle strikes the edge or the corner of the hob, the
hob may break.
WARNING: never use the glass-ceramic hob as support surface.
USING THE ELECTRIC THERMOSTAT
The thermostat supplied with the relative models maintains a constant temperature inside the oven at a specific
temperature setting ranging from 50°C to 250°C.(fig.17)
Turn the knob clockwise and align the selected temperature indicated on the ring with the index etched on the control
panel. Thermostat operation is indicated by an orange light which will turn off when the temperature inside the oven is
10°C greater than the temperature setting, and will turn on when the oven is 10°C less than the temperature setting. The
thermostat can control the oven elements only if the relative switch is in one of the possible oven element operating
modes: if the switch is in position 0, the thermostat has not effect on the oven elements, which remain off.
USING THE 9 + 0 SWITCH
The 9 + 0 switch installed in the multifunction oven models is used, along with the thermostat, to control the electric fan
and the oven elements since they can be turned on by turning the 9 + 0 switch knob and the thermostat knob. Turning
just one of the two knobs will not have any effect on the oven except to turn on the oven light or the electric fan when
inserted. The electric oven is heated by 4 elements: one on the bottom, two on the top or one circular; turning the switch
knob (fig.18) turns on the element relative to the symbol indicated on the ring but to be activated the thermostat knob
must be turned until the orange light turns on indicating that the element has been turned on. Placing the switch knob on
any of the nine operating modes turns on the oven light, together with the relative element. Once the temperature and
the elements to be used have been set, the oven elements are turned on and off by the thermostat; therefore, it is normal
for the orange light to turn on and off while the oven is working.
To turn off the electric oven set the switch knob to position 0 to prevent the thermostat from controlling the elements.
Setting the thermostat knob to position 0 turns off the elements but it is still possible, using the switch, to turn on the
electric fan and the oven light.
The switch has 9 different fixed positions corresponding to 9 different types of oven operation:
- the symbol
indicates that only the oven light is turned on;
- the symbol
on;
indicates that the bottom element (1300W) and the top external element (900W) have been turned
- the symbol
indicates that only the top external element (900W) has been turned on;
- the symbol
- the symbol
- the symbol
indicates the only the bottom element (1300W) has been turned on;
indicates that only the grill element (2000W) has been turned on;
indicates that the top external element (900W) and the grill element (2000W) have been turned on;
indicates that the top external element (900W), the grill element (2000W) and the electric fan have
- the symbol
been turned on;
- the symbol
indicates that the circular element (2400W) and the electric fan have been turned on;
indicates that only the electric fan has been turned on.
- the symbol
When the knob is set to one of these nine positions, the oven light is always on, thus indicating that the oven is being
energised.
7
USING THE NATURAL CONVENTIONAL ELECTRIC OVEN
When using the oven for the first time it should be operated for a maximum of 30 minutes at a temperature of about 250°
to eliminate any odours generated by the internal insulation. During normal oven use, select the desired cooking
temperature using the thermostat knob and wait until the orange light turns off before putting in any food. The oven is
equipped with 4 guides at different heights (fig.19) which can be used to insert shelves or the tray. To keep the oven as
clean as possible it is recommended to cook meat on the tray or on the shelf that has been inserted inside the tray. Table
below lists the cooking times and the position of the tray for different types of foods. Personal experience will help to
determine any variations in the values reported in the table. In any case, it is recommended to follow the instructions of
the specific recipe being used.
NATURAL CONVENTIONAL ELECTRIC OVEN COOKING TABLE
TEMP °C
HEIGHT
MINUTES
MEAT
PORK ROAST
BEEF ROAST (YOUNG STEER)
BEEF ROAST
VEAL ROAST
LAMB ROAST
225
225
250
225
225
230
250
250
250
225
250
250
3/4
3/4
3/4
3/4
3
3/4
3/4
3
3
3
3/4
3/4
60-80
60-80
50-60
60-80
40-50
50-60
40-50
60-80
50-60
60-70
45-60
40-45
ROAST BEEF
ROAST HARE
ROAST RABBIT
ROAST TURKEY
ROAST GOOSE
ROAST DUCK
ROAST CHICKEN
FISH
200-225
2
15-25
PASTRY
FRUIT PIE
TEA CAKE
BRIOCHES
SPONGE CAKE
RING CAKE
SWEET PUFF PASTRIES
RAISIN LOAF
STRUDEL
SAVOIA COOKIES
APPLE FRITTERS
SAZOIARDI SANDWICH
TOAST SANDWICH
BREAD
225
175-200
175-200
220-250
180-200
200-220
250
2
2
2
2
2
2
2
2
2
2
2
3
3
2
35-40
50-55
25-30
20-30
30-40
15-20
25-35
20-30
40-50
15-20
20-30
5
180
180-200
200-220
200-220
250
220
220
30
20
PIZZA
USING THE VENTILATED ELECTRIC OVEN
When using the oven for the first time it should be operated for a maximum of 30 minutes at a temperature of about 250°
to eliminate any odours generated by the internal insulation.
Before cooking, allow the oven to reach the desired temperature setting waiting for the orange light to turn off. This type
of oven is equipped with a circular element around which a fan has been installed that creates forced-air circulation in the
horizontal direction. Thanks to this type of operation, the ventilated oven can be used for different types of cooking at the
same time, without changing the taste of each food. Only some models are equipped with a removable metallic filter
applied to the rear screen which collects the fat while a roast is cooking. Therefore, it is recommended to remove this fat
periodically, washing the screen with soapy water and rinsing thoroughly. To remove the metallic filter just apply slight
pressure toward the top on the tab indicated by the arrow. Hot-air circulation guarantees a uniform distribution of heat.
Pre-heating the oven is not necessary, but for very delicate pastries, it is recommended to heat the oven before inserting
the trays.
The ventilated conventional system partially changes the various notions about traditional cooking. Meat no longer needs
to be turned while it is cooking and the rotisserie is no longer needed to cook a roast on the spit. Just put the meat
directly on the shelf.
8
VENTILATED ELECTRIC OVEN COOKING TABLE
TEMP °C
HEIGHT
MINUTES
MEAT
PORK ROAST
BEEF ROAST (YOUNG STEER)
BEEF ROAST
VEAL ROAST
LAMB ROAST
160-170
170-180
170-190
160-180
140-160
180-190
170-180
160-170
160-170
160-180
170-180
180
2
2
2
2
2
2
2
3
3
3
2
2
70-100
65-90
40-60
65-90
100-130
40-45
ROAST BEEF
ROAST HARE
30-50
ROAST RABBIT
ROAST TURKEY
ROAST GOOSE
ROAST DUCK
ROAST CHICKEN
80-100
160-240
120-160
100-160
70-90
FISH
160-180
2-3
PASTRY
FRUIT PIE
TEA CAKE
BRIOCHES
SPONGE CAKE
RING CAKE
SWEET PUFF PASTRIES
RAISIN LOAF
STRUDEL
SAVOIA COOKIES
APPLE FRITTERS
SAZOIARDI SANDWICH
TOAST SANDWICH
BREAD
180-200
200-220
170-180
200-230
160-180
180-200
230-250
160
150-180
180-200
170-180
230-250
200-220
200-220
2
2
2
2
2
2
2
2
2
2
2
3
3
2
40-50
40-45
40-60
25-35
35-45
20-30
30-40
25-35
50-60
18-25
30-40
7
40
20
PIZZA
USING THE CONVENTIONAL ELECTRIC GRILL
The electric grill can also be combined with the gas oven or electric oven.
In both cases, the grill is controlled using the oven’s temperature knob (see also, Using the gas or electric oven). Like
the gas grill, the electric grill can be used for grilling on the oven’s grill. The static electric grill must be used with the door
closed. The temperature set on the thermostat (when present) must not exceed 150°C.
Grilling on the shelf: In this case, the shelf supplied is placed on level 1 or 2 and the foods to be grilled are placed on
top, while the tray is inserted on the lower levels to collect the cooking juices. Then turn on the grill element switching the
thermostat to the relative position (electric oven version).
WARNING: the accessible parts may become very hot while grilling. Keep children away from the appliance
while cooking.
USING THE VENTILATED ELECTRIC GRILL
The ventilated electric grill is a special function equipped only on the multifunction oven. Set the 9 + 0 switch to the
relative position to activate the grill element and the electric fan. Generally, to ensure excellent grilling, place the oven
shelf in the middle position while the oven tray should be inserted at the bottom.
IMPORTANT: When using the ventilated electric grill, set the thermostat knob no higher than 175 °C, which is
between the 150 °C and 200 °C setting, to avoid overheating the front of the appliance. In fact, ventilated grilling
must be carried out with the door closed.
Note:
The cooker is equipped with the cooling fan that starts operation each time the oven knob is on a position different from 0
(zero). The fan circulates the air between the control panel and the oven door and also allows the control panel and the
oven door stay at a warm temperature during the appliance operation in any condition.
USING THE SELF-CLEANING OVEN
In the cookers where this feature is foreseen , the self-cleaning oven differs from the standard one for the fact that its
internal surfaces are enamelled with a special microporous material which absorbs and eliminates the greasy particles
during the cooking. In case of spillage of greasy liquids, the self-cleaning action becomes not efficient, therefore it will be
necessary to clean the oven properly. Proceed in the following way: (a) wipe a humid sponge on the grease stains; (b)
heat up the oven to the maximum temperature; (c) wait 5 minutes and then switch off the oven; (d) wait until the oven
gets cool again; (e) wipe again the humid sponge on all the surface. Do not use detergent in any case.
9
CLEANING THE APPLIANCE
Before cleaning the appliance, it should be disconnected from the power supply and turn off the main gas
feeder valve.
Cleaning the work surface:
Periodically clean the burner heads, the enamelled steel grids, the enamelled covers and the flame caps using warm
soapy water. Then those parts should be rinsed and thoroughly dried.
Any liquid that overflows from pots must always be removed using a rag.
If it becomes difficult to open or close a valve, do not force it, but immediately request the assistance of the
technical service personnel.
Cleaning the ceramic hob:
Sefore carrying out any operations, disconnect the appliance from the electricity supply.
The ceramic hob must be cleaned regularly, preferably atter each use, when the residual heat waming lights have gone
out.
Any marks left by the use of pans with aluminium bottoms can be wiped off with a cloth dipped in vinegar.
If burnt residues are left after cooking, remove them with the scraper provided, rinse with water and dry thoroughly with a
clean cloth. Regular use of the scraper considerably reduces the use of chemicals for daily cleaning of the hob.
In any case, abrasive or corrosive cleaners (e.g. powder products, ovencleaner sprays, stain removers and metal
scouring pads) must never be used.
Cleaning the enamelled parts:
To maintain the original features of the enamelled parts they should be cleaned frequently with soapy water. Never use
abrasive powders. Do not leave acidic or alkaline substances on the enamelled parts (vinegar, lemon juice, salt, tomato
sauce, etc.) and do not wash the enamelled parts while they are still hot.
Cleaning the STAINLESS steel parts:
Clean the parts with soapy water and then dry them with a soft cloth. The shine is maintained by periodically using
special products that generally are found in the market. Never use abrasive powders.
Cleaning the burner flame caps:
Since the flame caps are resting on the burner, to clean them just remove them from their seat and wash them with
soapy water. After they have been thoroughly dried and having checked that the holes are not clogged, they can be
replaced in their proper position.
Cleaning the inner glass door: Clean the glass with warm soapy water using a sponge. A spatula can be used to
remove burner fat if used gently.
ATTENTION: while cleaning the door make sure to avoid any spillage in the venting holes on the top part of the door. To
clean inside the door it is necessary to disassemble the door through a service engineer.
ATTENTION: for further details about cleaning of the appliance, please contact your applliance retailer.
AFTER-SALES TECHNICAL SERVICE AND SPARE PARTS
Before leaving the factory, this appliance was tested and calibrated by skilled and qualified personnel.
Any repairs or calibration that may become necessary after leaving the factory should be performed by skilled personnel.
For this reason we advise the customer to contact the Dealer that sold the appliance or the nearest Service Centre,
providing them with information about the type of appliance and the type of problem that has occurred. If defective parts
must be replaced, it is recommended to replace them with original spare parts that are available only in our technical
Service Centres and authorised dealers.
10
Fig. 1
Fig. 4
Fig. 5
11
Fig. 6
Fig. 7
Fig. 8
Fig.9
Fig.10
12
Fig.11
Fig.12
Fig.13
Fig.14
Fig.15
13
Fig.16
Fig.17
Fig.18
Fig.19
14
15
310692
16
|