27" Outdoor Cooking Center
Grill Cart
®
GE Monogram
Model ZX27CTYSS
Assembly Instructions
Before you Begin – Read these instructions completely and carefully.
Note To Installer: Be sure to leave these instructions with the Consumer.
Note to Consumer: Keep these instructions with your Use and Care Book for future reference.
Assembly of this grill cart requires basic mechanical
skills. Proper assembly is the responsibility of the
installer.
If you have questions concerning the installation of
this product, call the GE Answer Center® Consumer
Information Service at 800.626.2000, 24 hours a day,
7 days a week.
NOTE:
This cart must be completely assembled before any
gas connections are made.
If you received a damaged Grill Cart, you should
contact your dealer.
Open the box and remove the contents.
Remove packaging and protective film from
all parts.
Step 1:
Remove
Shelf Handle
Packaging
Shelf
Back Brace
Front Panel
Axle
Wheels
Bottom/Base Panel
Caster
Front Brace
Side Braces
Right Side Panel
Left Side Panel
Caster with Lock
Locate the hardware accessory package and check contents.
Self-tapping Screws
#10 Washers
Count 12
1/4 Washers
Count 40
Count 2
1/4-20 x 3/4 Bolts
Count 2
1/4-20 x 1/2 Bolts
Count 36
Phillips Head Screws
Count 10
8 required, 4 extra
32 required, 8 extra
no extra
32 required, 4 extra
8 required, 2 extra
Black Plastic
Grommet
Count 1
Wheel Caps
Count 2
1/4-20 Nuts
Count 36
32 required, 4 extra
10-24 Nuts
Count 10
8 required, 2 extra
Black Plastic
Bezels
Count 2
Installation
27" Grill Cart Assembly
•Flatten the carton to use as a pad.
•Stand the assembled base on end.
•Secure left and right side panels to the
bottom panel with 4 bolts, washers and nuts
(2 on each side). Note: Right side panel has
a hole near the center.
•Install bolt and washer from the bottom and
into the base, secure with nuts inside. Do not
tighten.
Step 3:
Install Side
Panels
to Base
Bottom Panel
Right Side Panel
USE
4
EACH
1/4-20 x 1/2
Bolts
1/4 Washer
1/4-20 Nuts
Step 4:
Install
Front Panel
to Base
Front Panel
Front Panel
Side Panel
Bottom Panel
USE
4
EACH
1/4-20 x 1/2
Bolts
1/4 Washer
1/4-20 Nuts
•Stand the assembly up and bolt the front
panel to the side panels with bolts, washers
and nuts as shown. (2 on each side).
USE
2
EACH
1/4-20 x 1/2
1/4 Washer
1/4-20 Nuts
Bolts
•Place the front panel on the assembly. Install
bolt with washer from the bottom into the
base and secure with nuts. Do not tighten.
3
Installation
27" Grill Cart Assembly
•Bolt back brace to side panels by installing
bolt with washer from the outside and
secured with nut on the inside. (2 bolts on
each side).
Step 5
Install
Back
Side Panel
Brace
Back Brace
USE
4
EACH
1/4-20 x 1/2
Bolts
1/4-20 Nuts
1/4 Washer
•Check to be sure all panels and holes in the
bottom right corner of the front panel are
correctly aligned.
•Tighten bolts by holding a 7/16" wrench on
bolt and turning nuts below with another
7/16" wrench.
Step 6
Check Panel
Alignment,
Tighten
•Snap grommet into the hole on the outside
of the right side panel.
Assembly
•Place wheel cap onto axle and tap in place
with a mallot.
•Slide a wheel onto the axle with the flat side
against the cap and the spacer side (the
protruding side) towards the inside of the
cart.
Step 7
Install
Wheels
•Slide the axle through the holes in the cart.
•Place second wheel onto the axle, with
spacer side against the cart, and tap wheel
cap with mallet to secure.
USE2
WHEELCAPS
4
Installation
27" Grill Cart Assembly
CAUTION: Lock front caster on the cart to
prevent movement.
Step 8
Mount Grill
to Assembled
Cart
See installation instructions packed with the
grill. Remove packaging, drip tray, burner
grates and parts box.
CAUTION: The grill is extremely heavy. 2
people are required to lift and place the grill
onto the cart.
•Lower the grill onto the cart.
•Check to be sure the grill rests securely and
fits square on the cart.
•Secure the grill to the cart with 2 bolts,
washer and nuts on each side. The bolts may
be accessed from the back of the cart.
USE
4
1/4-20 x 1/2
EACH
1/4 Washer
1/4-20 Nuts
Bolts
The shelf should be installed after the grill
has been secured to the cart.
•Place black plastic bezels onto the ends of
the handle.
•Hold the handle against the shelf and
secure with two 1/4-20 x 3/4" bolts as
shown.
Step 9
Install
Handle
on Shelf
USE
2
Use 2
Black Bezels
1/4-20x3/4
Bolts
•Hold the assembled shelf against the grill,
aligning screw holes.
•Install bolts and washer through the inside
of the grill, into the top of the shelf and
secure with nuts.
•Drive 2 self-tapping screws with washers into
the lower holes of the shelf and into the
grill.
Step 10
Mount Side
Shelf to
Grill
Self Tapping Screws
USE
2
EACH
Flat Washer
1/4-20 x 1/2
Bolts
Self-Tapping
Screws
1/4-20 Nuts
5
Notes
27" Grill Cart Assembly
6
Notes
27" Grill Cart Assembly
7
To obtain specific information concerning any
Monogram product or service, call GE Answer Center®
consumer information service at 800.626.2000—any
time, day or night.
For Monogram local service in your area, call
1-800-444-1845.
NOTE: Product improvement is a continuing endeavor at General
Electric. Therefore, materials, appearance and specifications are
subject to change without notice.
Pub. No. 49-8840
Dwg. No. 164D3333P080
1997 GE Appliances
(N.D. 723) 4/97
®
Monogram.
10744
General Electric Company
Louisville, KY 40225
|