®
GARDENA
HB 40
Art. 4005
MulchCut HB 40 Art. 4010
D
Gebrauchsanweisung
Hattrick
GB Operating Instructions
Hattrick
F
Mode d’emploi
Tondeuse Hattrick
NL Gebruiksaanwijzing
Hattrick
S
I
Bruksanvisning
Hattrick Gräsklippare
Istruzioni per l’uso
Hattrick
E
P
Manual de instrucciones
Hattrick
Instruções de utilização
Hattrick
35
G
GARDENA Hattrick HB 40
1. Technical data
HB 40 / MulchCut HB 40
Motor
Power
Capacity
petrol engine Briggs & Stratton (Quattro 40)
2.1 kW
158 cm3
Spark plug
Gap
Fuel tank capacity
Fuel
Champion RC-J-8 / Champion RJ-9LM
0.75 mm
1.0 l
Two-star petrol
Oil capacity
Casing
Cutting width
Cutting height
Weight
approx. 0.6 l (SAE 30 or 10W30)
plastic
40 cm
30-80 mm
31 kg
Grass catcher capacity
Wheels
Side force
55 l
ball bearing
50 N
Return force
Operational safety/gradients
50 N
15°
Working area related emission
1)
characteristic value LpA
81 dB(A)
2)
Noise level LWA
95 dB(A) / 94 dB(A)
Measuring method according to
Vibrations at handle avhw
2.4 ms-2
EN 836
directive 2000/14/EC
1)
2)
1)
2. Information concerning the instructions
Read these instructions carefully
and observe the information
contained in them. Acquaint your- of 16 as well as people, who
self with the use of the unit, the
adjustments, its proper use and
observe the safety instructions.
For safety reasons,
children under the age
Warning! For environ-
mental and transport
safety reasons the petrol
Hattrick lawn mower is supplied
without motor oil. Therefore,
the crankcase of the engine
must be filled with motor oil
(see 5.1) prior to use, otherwise
the engine will be damaged.
A
A
are not acquainted with the
instructions should not use
this Hattrick.
Keep these instructions in
a safe place.
3. Proper use
The GARDENA petrol Hattrick
lawn mower has been designed
for cutting lawn and grass areas
of private houses.
It is absolutely necessary to
be used for trimming bushes,
hedges or shrubs, for cutting
and pruning of climbers or
grass on roof or balcony gar-
dens. Additionally, the Hattrick
must not be used for chopping
up branches and twigs and
for levelling irregularities in the
soil surface.
observe the manufacturer’s oper-
ating instructions to ensure the
unit’s proper functioning. These
instructions also contain hints on
service, maintenance and repair.
This appliance is for private use
only and is not designed for use in
public places, parks, sport arenas,
street-scapes, in agriculture or
forestry.
Attention! For health and
safety reasons the petrol
Hattrick lawn mower should not
A
15
G
G
5.2 Starting the Hattrick
lawn mower (Fig. F)
Place your petrol Hattrick lawn
mower on an even area of the
lawn.
After that, the starter handle/cord Do not let the engine run in
4. Assembly (Fig. A-D)
closed spaces. There is danger
of carbon monoxide poisoning.
(13) must be allowed to return
slowly.
4.1 Contents
The packaging should include
the following parts:
petrol and brake bowden cables
(4/5). Insert the enclosed bolt (8)
from the outside through the
bore hole of the top of the guide
handle (A2).
4.5 Fixing the bowden cables
The motor speed can be reduced
by pushing the throttle (3) towards
(Fig. C)
Never start up on a solid sur-
faced area (e.g. drives, tarred
surfaces etc.) with the aerator
roller switched on and a cutting
height of less than 55 mm as
the aerator springs can have
contact with the ground at this
setting.
Insert both petrol and brake
bowden cables into the provided
bowden cable clip (16) and press
them onto the bottom part of
the guide handle (A1).
.Hattrick HB 40
the symbol
(turtle).
If the engine is cold, press the
primer (23) several times before
starting. If the engine is hot there
is no need to use the primer (23).
.Grass Catcher (disassembled)
.Top of guide handle
.Fastening parts for
guide handle and throttle
.Bowden cable clip
.Spark plug spanner
.Operating instructions
.TORX®-wrench
Release brake lever (10) to switch
off the engine.
The bolt (8) is located firmly by
the square bolt head, into the
guide handle.
Make sure that the blades
and aerator roller (see 6.3)
can run freely before starting
the mower. Tilt the mower on
the rear wheels by pressing on
the guide handle.
Press brake lever (10) down to
the top of the guide handle (A2).
4.6 Assembly of the
A
Lift the brake lever (10) and insert grass catcher (Fig. A/D)
the brake bowden cable (11)
from the outside into the corre-
Attention! Be aware that the
cutting blades take a while
to stop after turning off the
engine.
The grass catcher is supplied
loose (3 component parts).
sponding bore hole (12). The cas- The carrying handle (17) is under
ing of the throttle (9) is now insert- the protective cover (27).
Push the throttle (3) to the symbol
(hare) and pull the starter
handle/cord (13) slightly until the
ratchet engages. Start the engine
by quickly pulling out the starter
handle/cord (13).
for changing blades
4.2 Assembly of the
guide handle (Fig. A)
ed onto the bolt (8) on the top of
Unfold the grass catcher (18) and
the guide handle (A2).
insert the supporting frame (19)
Insert washer (7) before fastening
through the opening of the grass
the nut (6) (as illustrated).
Swivel the folded bottom part
of the guide handle (A1) into the
working position and allow it to
engage. Tighten well with the
lower linkage locking handles (2).
Put the top of the guide handle
(A2) onto the bottom part of the
guide handle (A1) and secure
using the fastening parts (thread-
ed bolt; plastic wing nut) (1).
catcher (18) so that the plastic
6. Information concerning correct mowing and aerating
base is at the bottom.
4.4 How to attach the starter
Then open the fastening clamps
handle onto the top of the
6.1 General remarks
on the care of lawns
To keep your lawn well-groomed
we recommend cutting it regularly no uncut strips are left behind.
mower in rows as straight as pos- 6.3 Mowing with the
(20) by hand and fix them onto
guide handle (Fig. C)
sible. Ensure that the rows over-
lap by a few centimetres so that
aerator cylinder (Fig. H)
the supporting frame (19).
By pushing the brake lever (10)
Fasten the carrying handle (17)
down, the brake is released from
by pressing onto the supporting
the engine. The starter handle
frame (19).
Switching the aerator cylinder
on/off
Switch off the engine before
switching the aerator cylinder
on or off.
To switch on the aerator cylinder
set the rotary switch (26) to
position “I”.
once a week. Depending on the
Guide the Hattrick in walking
growth of moss and weeds,
pace only.
(13) with starter cord (14) can now
be pulled out of its resting position Note:
on the petrol motor. Now thread
switch on the aerator cylinder as
4.3 Assembly of the throttle
(Fig. B)
The throttle (3) is already con-
nected in working order to the
The supporting frame (19) is
the starter cord (14) into the guide shaped to locate the carrying
required.
Adjusting the cutting height
(Fig. G)
With frequent mowing and aerat-
ing the lawn becomes healthy
and strong.
rings (15) on the top of the guide
handle (A2).
handle (17) in the correct
position.
The petrol Hattrick lawn mower
has a central cutting height ad-
justment knob (24). In front of
the knob (24) the cutting height
is displayed (25) increments
of 5 mm.
To switch it off set the rotary
switch (26) to position “0”.
Short clippings (up to a length
of about 1 cm) can be left on the
lawn. Longer clippings must be
removed to prevent the lawn
becoming yellow or matted.
5. Initial operation (Fig. E/F)
Remarks on mowing with the
aerator cylinder switched on
Cutting height range 30 - 80 mm The aerator cylinder can be used
5.1 Preparation for initial
operation (Fig. E)
integrated in the oil sealing cap
(21). The oil level must be bet-
ween the ADD and FULL mark.
removed and no petrol may be
added if the engine is running
or is hot. If petrol is spilled dur-
ing filling, the engine must not
be started until the spilled
petrol has been wiped up and
the mower has been removed
from the area where the fuel
was spilled. No attempt must
be made to switch on the igni-
tion until the petrol vapours
have dispersed.
for creating drainage, removing
matting and moss in the lawn
as well as for cutting flat-rooting
weeds.
Cut and aerate the lawn for the
first time in spring when the grass When working on slopes, al-
begins to grow and can be walked ways mow at right angles to
Note:
For environmental and
transport safety reasons
A
Always check the oil level
before mowing.
the petrol Hattrick lawn mower
is supplied without motor oil.
Therefore, the crankcase of
the engine must be filled with
0.6 l motor oil (SAE 30 or
10W30).
on. If the grass has grown too
long, first cut it lengthwise with
a high cutting setting (without
switching on the aerator cylinder)
and then cut at right angles with
the desired cutting setting, with
the aerator cylinder (optional)
switched on.
the slope. To prevent the petrol
Hattrick lawn mower from slid-
ing way, point it slightly uphill.
The recommended fuel is
unleaded two-stroke petrol.
If the grass is particularly long
due to infrequent lawn care (e.g.
after holidays), disengage the
aerator cylinder, and pre-cut with
the maximum cutting height
to prevent overload of the lawn
mower.
Take extra care when changing
direction on slopes.
Warning! Fuel is highly
inflammable. Fuel must
be stored only in containers
A
Unscrew the oil sealing cap (21)
and fill with 0.6 l of SAE 30 quality authorised for the purpose.
oil.
The oil level can be checked
(when engine is switched off)
by means of the oil dip stick (22)
For safety reasons, slopes
with a gradient of more than
15° must not be mowed.
To safeguard against fire,
keep grass, leaves, grease and
oil away from engine and ex-
haust.
The fuel must be filled only
outdoors; do not smoke during
filling. Fill with petrol prior to
use; the petrol cap must not be
At the end of the cutting row
or for turning around, tilt the
mower on the rear wheels by
pressing on the guide handle.
This way you can turn it easily
with the aerator cylinder run-
6.2 Mowing (Fig. G-I)
Always keep the under side of
the mower casing clean and
remove grass deposits. De-
posits complicate the start-up
procedure and affect the cut-
Cut only with sharp blades so
that the grass does not fray and
the lawn does not turn yellow.
To obtain a clean cutting result
guide the petrol Hattrick lawn
ting result as well as discharge ning free.
of grass clippings.
16
17
G
G
After having aerated heavily
moss-covered areas, it is re-
commended to resow the lawn.
This will help the affected lawn
to recover quickly.
The aerator cylinder use is
optional depending on the needs
and condition of the lawn.
The table below provides infor-
mation on the use of the aerator
cylinder.
Follow the manufacturer’s
instructions when replacing
the blades, blade bar and for
aerator cylinder.
4. Reverse the blades (30) or
mount new blades (30) and
secure tightly (torque 25 Nm).
(During installation make sure
that the ratchet toothed locking
washers (31) are fitted under
the nuts (28) and that the nuts
(28) are on the top of the blade
bar (32).)
tank lid is properly closed.
Tilt the lawn mower to the
tank-located side; keep spark
plugs and sound absorber of
the motor upwards.
7.2 How to replace the blades,
blade bar and the aerator
cylinder (Fig. K-M)
Please use only the Original
GARDENA Spare Blades:
3. Release screws (39) with
an appropriate Phillips head
screwdriver.
4. Remove the bearing sheet
steel (40).
5. Remove aerator cylinder (38)
together with end plate (41)
of the drive shaft (42) (square)
by tilting and pulling out.
6. Place new aerator cylinder (38)
onto drive shaft (42) (square);
stick on end plate (41) and
tighten with the bearing sheet
steel (40) in the casing.
Use of the aerator cylinder
Cutting height setting
Function of the aerator cylinder
Deep aeration of the soil
30 - 35 mm
The aerator springs penetrate up to 7 mm
deep depending on the type of soil.
Replacing the blade bar
(Fig. L)
Triangular blades
(HB 40)
Aeration of the soil surface
35 - 40 mm
The aerator springs remove moss,
matting, and weeds rooting near the
surface.
Art. No. 4098 Damaged blade bars must be
Rectangular Blades
(MulchCut HB 40) Art. No. 4099
Aerator cylinder Art. No. 4097
replaced to prevent imbalance.
1. Remove the spark plug in
order to avoid risk of injury
if the engine accidentally
is started.
Combing the lawn
40 - 45 mm
40 - 55 mm
The aerator springs remove residues from
the lawn.
You can order these spare parts
from your GARDENA dealer
or directly from the GARDENA
customer service.
Gathering grass clippings etc.
The aerator springs remove even wet or
trodden-in grass clippings etc. from the
lawn.
2.
Empty the tank or run
the mower until the
tank is empty! Make sure the 7.3 Engine maintenance
A
Never use spare parts or ac-
cessories which have not been
designed by the manufacturer!
tank lid is properly closed.
Changing oil (Fig.E)
Tilt the lawn mower to the
Always change the oil when
tank-located side; keep spark
the engine is hot and the tank
plugs and sound absorber of
is empty and closed.
6.4 Mowing with the
grass catcher (Fig. I)
As soon as there are grass clip-
pings left on the lawn during
mowing and aerating, the grass
catcher should be emptied.
be difficult to start. Pull the petrol
Hattrick lawn mower back about
1 m so that the grass clippings
drop out easily.
Afterwards, the grass catcher
should be emptied.
the carrying handle (17) and in-
sert into the the discharge open-
ing from above.
Replacing the blades (Fig. K)
the motor upwards.
Note:
Note:
3. Release the hexagon head
bolt (33) with an appropriate
wrench (SW 13) and remove
the blade bar (32) from the
drive shaft.
4. Insert new blade bar and
tightly screw with the following
washers (in the same order):
a) fibre washer (34)
Carry out the first motor oil
If properly seated the protec-
tive cover (27) fits snugly to
the grass catcher (18).
The blade has two cutting
edges. If one edge has become
blunt the blade can be re-
versed. Broken blades must be
replaced immediately as it can
cause an imbalance problem.
change after 5 hours of operation,
then every 50 hours of operation
or once a year at the end of the
mowing season, depending on
which comes first.
In order to do this, open oil seal-
ing cap (21), tilt the mower so
that the old oil can flow into an
oil-trough. Dispose of waste oil
according to local regulations.
To remove the grass catcher (18)
lift the protective cover (27) on
your petrol Hattrick lawn mower
with one hand. With the other
hand hold the grass catcher (18)
by the carrying handle (17) and
remove the grass catcher (18)
upwards.
Note:
To ensure good collection, re-
gularly clean the grass catcher
inside and outside.
Mowing without
the grass catcher
The protective cover (27) is
mounted in such a way that the
petrol Hattrick lawn mower can
be used without the grass catcher
with the protective cover (27)
closed. The clippings are ejected
onto the lawn below the protec-
tive cover (27).
Do not regrind the blades, it
will cause imbalance.
Attaching the grass catcher
Attach the grass catcher
b) strain washer (35)
The blades must always be
replaced or reversed in pairs.
c) small steel washer (36)
and with the hexagon head
bolt (33) (Torque: 40 Nm).
A
only with the engine
switched off and the cutting
blade at a stand still.
If the protective cover (27) is re-
leased, it automatically shuts and
covers the discharge opening.
Position the mower on a level
surface again and fill it with motor
oil (0.6 l SAE 30 or 10W30)
(see 5.1).
When replacing the blades
always use the new nuts and
bolts supplied with the spare
blades.
Be sure that strain washer (35)
has been installed in the cor-
rect position (see fig. L1).
Lift the protective cover (27) with
one hand. With the other hand
hold the grass catcher (18) by
If grass clippings stick in the dis-
charge opening, the mower may
Checking and cleaning
1. Remove the spark plug in
order to avoid risk of injury
if the engine is accidentally
started.
Replacing the aerator cylinder
(Fig. M)
The aerator cylinder is subject
to natural wear and tear. If the
springs (37) are worn it will not
function correctly.
the spark plug
Clean a contaminated spark plug
with a brass wire brush and rag.
Check the electrode gap (setting:
0.75 mm gap). Replace a badly
worn or damaged plug.
7. Maintenance, service, storage
2.
Empty the tank or run
the mower until the
tank is empty! Make sure the The aerator cylinder (38) must
tank lid is properly closed.
Tilt the lawn mower to the
tank-located side; keep spark
plugs and sound absorber of
the motor upwards.
7.1 Maintenance
Repairs may only be carried
For security reasons, replace
the tank lid if damaged.
A
Maintenance includes all jobs
which keep your petrol Hattrick
lawn mower in perfect working
order. By regularly checking the
unit (firm seating of screw con-
nections, cracks, damage) and
replacing defective or worn parts
you can prevent accidents and
failure.
out by GARDENA service
centres or dealers authorised
by GARDENA.
Cleaning the air filter (Fig. N)
Cleaning the air filter is ne-
cessary every 3 months or after
25 hours of operation. In ex-
treme dusty conditions do so
more frequently.
Never clean your petrol Hattrick
lawn mower with running water,
in particular with water under
high pressure.
be replaced.
1. Remove the spark plug in
order to avoid risk of injury
if the engine is accidentally
started.
Attention: Always detach
the spark plug before
working on your petrol Hattrick Store your petrol Hattrick lawn
lawn mower (for checking and
maintenance) to prevent risk
of injury!
A
3. Hold the locking nuts (28) at
the back and unscrew the bolts
(29), using the TORX®-wrench
provided.
mower in a dry place where
it is protected from frost. The
lawn mower should be stored
out of the reach of children.
2.
Empty the tank or run
the mower until the
tank is empty! Make sure the
Remove screw (43).
Fully remove air filter by pulling
sideways and/or from the front.
A
18
19
G
G
Make sure that no foreign
substances fall into the car-
burettor. Afterwards pull
cover (44) upwards. Completely
disassemble the air filter (45)
and clean all parts.
Hattrick lawn mower on its side
opposite the tank and clean it
with a brush or rag.
Unscrew the spark plug and
Problem
Possible cause
Remedy
pour 1 tablespoon of motor oil
into the cylinder. Turn the motor
by slowly pulling on the starter
handle/cord so that the oil is
distributed. Screw in the spark
plug again.
Uneven running.
Strong vibration of the unit.
Blade bar or blades damaged
(imbalance).
Blade bar fastening on motor
shaft is loose.
Replace damaged parts.
Tighten the blade or blade bar
bolts.
7.5 Storage (Fig. A)
Let the engine cool down be-
fore storing the petrol Hattrick
lawn mower in a closed room.
Cleaning the foam element.
Clean foam element in liquid
detergent and water. The foam
element should be replaced if
it is extremely dirty or damaged.
Engine does not start.
Primer has not been operated
before starting.
Press primer several times
(see 5.2).
After having thoroughly removed
dirt and remaining grass we re-
commend you to clean the petrol
Never store the petrol Hattrick
lawn mower with fuel in the
Spark plug defective or
tank empty.
Clean and replace spark plug,
fill fuel tank.
tank where petrol vapour could Hattrick lawn mower with mainte-
come into contact with an
open flame or could be ignited.
nance spray.
After cleaning press dry the
foam element with a clean rag.
Re-moisten the foam element
with oil.
Engine runs for a short time
but then suddenly stops
with a loud bang.
No motor oil in crankcase.
Piston and crankshaft bearings
have jammed.
Engine overhaul by a Service
Centre.
If you have any problem with
your petrol Hattrick lawn mower,
please contact our Customer
Service or return the defective
Always store your petrol Hattrick
lawn mower in a closed dry place.
Aerator cylinder does not run.
Rotary switch is in “0” position.
V-belt defective.
Set rotary switch to “I” position.
Re-assemble all parts in reverse
order and secure with screw (43)
onto carburettor.
To save space the handle can
be folded down. Loosen the lower unit together with a short descrip-
locking handles (2) and pull the
bars sideways out of the mount.
Loosen plastic wing nut (1) at the
joint. Fold guide handle down in
a Z-shape.
Replace V-belt. Contact
GARDENA service station.
tion of the problem and, in case
of guarantee, with a copy of the
receipt to one of the GARDENA
service centres listed on the rear
page.
Cleaning the cooling air
passages
Clean grass from cooling fins
and air passages.
Lawn turns to yellow.
Not a clean cut.
Blades are too blunt.
Replace or reverse the blades.
Correct cutting height.
Cutting height is too low.
We expressly point out that,
in accordance with the product
liability law, we are not liable
for any damage caused by our
units if it is due to improper
repair or if parts exchanged are
not original GARDENA parts
or parts approved by us, and
if the repairs were not carried
out by a GARDENA Service
Centre or an authorised spe-
cialist. The same applies to
spare parts and accessories.
If any other faults occur, please contact GARDENA Service.
Service interval
When folding down the
bars make sure that the
gas and brake bowden cables
are not jammed or damaged.
In order to achieve trouble-free
operation of the engine, this lawn
mower should be checked every
2 to 3 years by a GARDENA
Service Centre or a dealer
authorised by GARDENA.
A
9. Advice for proper use / safety instructions
Checks before each
operation
You are responsible for the
safety of the working area.
If, in spite of care, there is an
obstruction when cutting, turn
off the petrol Hattrick lawn
mower and remove it. Check
the unit for damage and have
it repaired if necessary.
Wintering
A
If the engine is shut down for
more than 30 days, firstly empty
the tank. Afterwards, let the
engine run until it runs out of
petrol.
Inspect the unit before each
use. Do not use the petrol
Hattrick lawn mower if safety
devices (safety handle; safety
cover) and/or the blade bar
or the blades are damaged or
worn. Never operate the unit
with the safety devices by-
passed or missing.
Only use the petrol Hattrick
lawn mower for the purposes
specified in these instructions.
7.4 Service
Residual dirt and grass can be
most easily removed immediately
after mowing. Place the petrol
Only work when visibility is
good.
A
Interruption to work
Familiarise yourself with the
surroundings of your working
area. Check for possible risks
Never leave the petrol Hattrick
lawn mower to run unattended.
8. Trouble-shooting
which might be not audible due If your work is interrupted,
The following table contains the
problems most frequently occur-
ring and shows how to remedy
them.
For safety, please contact
one of the GARDENA service
centres or an authorised
specialist for any other pro-
blem.
Inspect the area to be cut
before beginning work.
Remove any foreign objects
(e.g. stones) from the area.
Check the working area for
foreign objects (e.g. stones)
while working.
to the noise of the machine.
store the unit in a safe place.
Remove the spark plug!
Wear non-slip shoes and long
trousers to protect your legs.
When changing to another
working area, switch off the
petrol Hattrick lawn mower.
Keep fingers and feet away
from the cutting blades and
the aerator cylinder.
Problem
Possible cause
Remedy
The blade bar and the blades
must be checked regularly
for damage and properly re-
paired if necessary.
A
Check local regulations
Abnormal noise.
Clattering in the unit.
Motor fixing screws or
mower casing loose.
Tighten screws.
Make sure that there are no
other people (especially chil-
dren) or animals anywhere
near the working area.
Never use the unit when it is
raining or in damp or wet areas.
Whistling noise.
Foreign body blocking
aerator cylinder.
Switch off aerator cylinder,
remove the spark plug, remove
foreign body.
Do not use the petrol Hattrick
lawn mower in or near swim-
ming pools or ponds.
Proper use /
Ensure that you have a secure
foothold when working.
Attention! Take extra care
when walking backwards.
You may stumble!
A
responsibility
V-belt slipping.
Contact GARDENA Service
Centre.
Lawn mowers can cause
serious injuries!
Please observe the local re-
gulations regarding quiet times.
20
21
G
EU Certificate of Conformity
The undersigned
GARDENA Kress + Kastner GmbH · Hans-Lorenser-Str. 40 · D-89079 Ulm
hereby certifies that, when leaving our factory, the units indicated below are in accordance with the
harmonised EU guidelines, EU standards of safety and product specific standards.
This certificate becomes void if the units are modified without our approval.
Description of the units:
Hattrick
Harmonised European
standards:
EN 292-1
EN 292-2
EN 836
Ulm, 08.02.2002
Types:
HB 40 / MulchCut HB 40
Thomas Heinl
Technical Director
Art. No.:
4005 / 4010
Noise level:
measured / guaranteed
95 / 96 dB(A)
EU directives:
HB 40
Machinery Directive 98/37/EC
Electromagnetic Compatibility
89/336/EC
Directive 93/68/EC
Directive 2000/14/EC
MulchCut HB 40 94 / 96 dB(A)
Year of CE marking:
1996 (HB 40)
1998 (MulchCut HB 40)
22
the unit or repair it free of charge
if the following conditions apply:
.The unit must have been
handled properly and in keep-
ing with the requirements of
the operating instructions.
.Neither the purchaser or a
non-authorised third party have
attempted to repair the unit.
Une intervention sous garantie
ne prolonge pas la durée initiale
de la garantie contractuelle.
D
Garantie
GARDENA gewährt für dieses
Produkt die gesetzliche Garantie
(ab Kaufdatum). Abweichend
davon werden für das Kunststoff-
gehäuse 10 Jahre Garantie ge-
währt. Diese Garantieleistung
bezieht sich auf alle wesentlichen
Mängel des Gerätes, die nach-
weislich auf Material- oder Fabri-
kationsfehler zurückzuführen
sind. Sie erfolgt durch die Ersatz-
lieferung eines einwandfreien
Gerätes oder durch die kosten-
lose Reparatur des eingesandten
Gerätes nach unserer Wahl,
wenn folgende Voraussetzungen
gewährleistet sind:
Toutes les revendications dé-
passant le contenu de ce texte
ne sont pas couvertes par la
garantie, quel que soit le motif
de droit.
Pendant la période de garantie,
le Service Après-Vente et les
Centres SAV agréés effectue-
ront, à titre payant, les répara-
tions nécessaires par suite de
manipulations erronées.
The triangular blades (Hattrick)/
rectangular blades (MulchCut)
and the aerator cylinder are wear-
ing parts and are not covered
by the guarantee.
This manufacturer’s guarantee
does not affect the user’s exist-
ing warranty claims against the
dealer/seller.
En cas de réclamation, veuillez
envoyer le produit en port payé
avec le bon d’achat et une de-
scription du problème, à l’adresse
du Service Après-Vente figurant
In case of claim, please return
the faulty unit together with a copy au verso.
of the receipt and a description
of the fault, with postage paid to
one of the GARDENA Service
Centres listed on the back of
these operating instructions.
.Das Gerät wurde sachgemäß
und laut den Empfehlungen
in der Gebrauchsanweisung
behandelt.
.Es wurde weder vom Käufer
noch von einem Dritten ver-
sucht, das Gerät zu reparieren.
N
Garantie
GARDENA geeft op dit product
de wettelijke garantie (vanaf de
aankoopdatum). Op het kunststof
maaihuis is echter een garantie
van 10 jaar van toepassing. Deze
garantie heeft betrekking op alle
wezenlijke defecten aan het toe-
stel, die aanwijsbaar op mate-
riaal- of fabricagefouten berusten.
Garantie vindt plaats door de le-
vering van een vervangend appa-
raat of door de gratis reparatie
van het ingestuurde apparaat,
naar onze keuze, indien aan de
volgende voorwaarden is voldaan:
.Het apparaat werd vakkundig
en volgens de adviezen in de
gebruiksaanwijzing behandeld.
.Noch de koper, noch een
Die Verschleißteile Dreieckmes-
ser (Hattrick) / Rechteckmesser
(MulchCut) und Lüfterwalze sind
von der Garantie ausgeschlossen.
F
Garantie
GARDENA accorde pour cet ap-
pareil la garantie légale à comp-
ter du jour de l’achat. Le carter
en polypropylène est, lui, garanti
10 ans. La garantie est assurée
par le remplacement gratuit des
pièces défectueuses ou de l’ap-
pareil. Le choix en étant laissé
à la libre initiative de GARDENA.
En tout état de cause s’applique
la garantie légale couvrant toutes
les conséquences des défauts
ou vices cachés (article 1641 et
suivants du Code Civil).
Diese Hersteller-Garantie berührt
die gegenüber dem Händler/
Verkäufer bestehenden Gewähr-
leistungsansprüche nicht.
Im Reklamationsfall schicken Sie
bitte das defekte Gerät zusam-
men mit einer Kopie des Kauf-
belegs und einer Fehlerbeschrei-
bung frankiert an die auf der
Rückseite angegebene Service-
adresse.
Pour que ces garanties soient
valables, les conditions suivantes
doivent être remplies :
.L’appareil a été manipulé de
manière adéquate, suivant les
instructions du mode d’emploi.
.Il n’y a eu aucun essai de
réparation, ni par le client, ni
par un tiers.
derde persoon heeft getracht
het apparaat te repareren.
G
Guarantee
De aan slijtage onderhevige
driehoeksmessen (Hattrick) /
rechthoeksmessen (Hattrick-
mulchmaaier) en de verticuteer-
rol vallen niet onder de garantie.
GARDENA honours the guaran-
tee legally required for this pro-
duct (starting from the date of
purchase). As an exception, we
guarantee the plastic casing for
10 years. This guarantee covers
all serious defects of the unit
that can be proved to be material
or manufacturing faults. Under
warranty we will either replace
Deze garantie van de producent
heeft geen betrekking op de ten
aanzien van de handelaar/ver-
koper bestaande aansprakelijk-
heid.
Les lames triangulaires (Hattrick)
/ lames rectangulaires (MulchCut)
et le rouleau d’aération sont des
pièces d’usure et sont par con-
séquent exclues de la garantie.
71
Deutschland
GARDENA Kress + Kastner GmbH
GARDENA Service
Hans-Lorenser-Straße 40
D-89079 Ulm
Produktfragen: (0731) 490-123
Reparaturen: (0731) 490-290
Finland
Norway
Habitec Oy
GARDENA Norge A/S
Postboks 214
2013 Skjetten
Martinkyläntie 52
01720 Vantaa
France
Poland
GARDENA France
Service Après-Vente
BP 50080
GARDENA Polska Sp. z o.o.
Szymanów 9 d
Argentina
05-532 Baniocha
Argensem S.A.
95948 ROISSY CDG Cedex
Portugal
Venezuela 1075
Great Britain
MARKT (Portugal), Lda.
Recta da Granja do Marquês
Edif. GARDENA
(1618) El Talar - Buenos Aires
GARDENA UK Ltd.
27-28 Brenkley Way
Blezard Business Park
Seaton Burn
Australia
NYLEX Corporation Ltd.
25-29 Nepean Highway
P.O. Box 68
Algueirão
2725-596 Mem Martins
Newcastle upon Tyne
NE13 6DS
Russia / Россия
АО АМИДА ТТЦ
Mentone, Victoria 3194
Austria
Greece
ул. Моcфилмовcкая 66
117330 Моcква
GARDENA Österreich Ges. m.b.H.
Stettnerweg 11-15
2100 Korneuburg
Agrokip G. Psomadopoulos & Co.
20, Lykourgou str.
Kallithea - Athens
Singapore
Variware
Holland Road Shopping Centre
227-A 1st Fl., Unit 29
Holland Avenue
Singapore 1027
Belgium
Hungary
MARKT (Belgium) NV/SA
Sterrebeekstraat 163
1930 Zaventem
GARDENA Magyarország Kft.
Késmárk utca 22
1158 Budapest
Brazil
Iceland
Heimilistaeki hf
Saetun 8
P.O. Box 5340
125 Reykjavik
Slowenia / Croatia
Silk d.o.o. Trgovina
Brodišče 15
M. Cassab
Av. das Nações Unidas, 20.882
Santo Amaro, CEP 04795-000
São Paulo - S.P.
1236 Trzin
South Africa
Bulgaria / България
ДЕНЕКС ООД
бул. „Черни връх“ 43
София 1407
Republic of Ireland
Michael McLoughlin & Sons
Hardware Limited
Long Mile Road
GARDENA South Africa (Pty.) Ltd.
P.O. Box 11534
Vorna Valley 1686
Spain
Dublin 12
Canada
ANMI Andreu y Miriam S.A.
Calle Pere IV, 111
08018 Barcelona
GARDENA Canada Ltd.
100, Summerlea Road
Brampton, Ontario
Canada L6T 4X3
Italy
GARDENA Italia S.r.l.
Via Donizetti 22
20020 Lainate (Mi)
Sweden
GARDENA Svenska AB
Box 9003
Chile
Japan
Antonio Martinic Y CIA. LTDA.
Gilberto Fuenzalida 185 Loc.
Las Condes - Santiago de Chile
KAKUDAI Mfg. Co. Ltd.
1-4-4, Itachibori Nishi-ku
Osaka 550
20039 Malmö
Switzerland
GARDENA Kress + Kastner AG
Bitziberg 1
Costa Rica
Luxembourg
Magasins Jules Neuberg
Grand Rue 30
Case Postale No. 12
Luxembourg 2010
Compania Exim
Euroiberoamericana S.A.
350 Sur del Automercado
Los Yoses
8184 Bachenbülach
Ukraine / Украина
АОЗТ АЛЬЦЕСТ
ул. Гайдара 50
г. Киев 01033
San Pedro
Netherlands
Cyprus
GARDENA Nederland B.V.
Postbus 50176
Turkey
FARMOKIPIKI LTD
P.O. Box 7098
74, Digeni Akrita Ave.
1641 Nicosia
Dost Diþ Ticaret Mümessillik A.Þ.
Yeþilbaðlar Mah. Baþkent
Cad. No. 26
Pendik - Ýstanbul
USA
GARDENA
1305 AD ALMERE
Neth. Antilles
Jonka Enterprises N.V.
Sta. Rosa Weg 196
P.O. Box 8200
Czech Republic
GARDENA spol. s.r.o.
Řípská 20
Curaçao
3085 Shawnee Drive
Winchester, VA 22604
62700 Brno
New Zealand
NYLEX New Zealand Limited
Private Bag 94001
South Auckland Mail Centre
10 Offenhauser Drive
East Tamaki, Manukau
Denmark
GARDENA Danmark A/S
Naverland 8
4005-20.960.07/0021
GARDENA Kress + Kastner GmbH
Postfach 27 47, D-89070 Ulm
http://www.gardena.com
2600 Glostrup
76
|