Gifts that Bloom Video Game Console PM0070 0C User Manual

O WNER’S MANUAL  
FOR TECHNICAL ASSISTANCE  
CONTACT:  
Merit Industries, Inc. Customer Service Department  
USA and Canada call toll-free:  
1-800-445-9353  
Outside the USA and Canada call: (215) 639-4700  
FAX: (215) 639-5346  
2525 State Rd., P.O. Box 5004, Bensalem, PA 19020-8529  
merit industries, inc.  
PM0070-0C  
 
COPYRIGHT 1996 MERIT INDUSTRIES, INC.  
Once the second circle is touched, a crosshair will  
Monitor Colors Adjustment  
Procedure  
appear on the screen. To test the calibration of the  
screen, touch the crosshair with your finger and  
slowly drag your finger around the screen. The  
crosshair should follow your movement.  
For adjusting the colors on any of our monitor types, we  
suggest following the procedures described below.  
Touch the EXIT TESTicon.  
For all monitor types, the visual cues used to adjust the  
monitors are white cards and gray boxes (e.g. the  
speed bonus box); you will adjust the monitor controls  
until the cards are white and the boxes are gray.  
Degaussing your Monitor  
If your monitor is displaying purity problems,(a  
display with purity problems will have parts of an all-  
white screen affected by blotches of color) the monitor  
needs to be degaussed using a degaussing coil.A  
degaussing coil is a circular electromagnet, used to  
cancel out any stray magnetic fields that may build up  
on a metal object.  
Ducksan Monitors  
1. Set the game to the Run 21 hi-score screen.  
2. Reduce the brightness from the monitor control  
panel and adjust the RGB CUTOFF controls (as  
needed) until the background is black.  
3. Enter the Run 21 game screen. Reduce the  
brightness and adjust the RB DRIVE controls until  
the speed bonus box is light gray and the cards are  
white (there is no Green DRIVE control, so adjust  
the Green CUTOFF control if there is too much, or  
too little, green).  
All of our monitors have built-in degaussing coils that  
are automatically activated on power-up. If your game  
is experiencing minor purity problems, try powering  
down the game for 5 minutes and then reapplying  
power to activate the degaussing coil. If the problem is  
not corrected, you will have to use a manual  
degaussing coil.  
Wells-Gardner and Telco Monitors  
1. Set the game to the Run 21 hi-score screen.  
Follow the instructions below for degaussing a monitor.  
1. Plug in your degaussing coil.  
2. Reduce the brightness from the monitor control  
panel and adjust the RGB CUTOFF controls (as  
needed) until the background is black.  
2. Hold the coil about three feet from the monitor,  
press the trigger to activate the magnetic field (for  
circular-shaped coils, orient the coil so you see the  
monitor through the hole in the middle; for wand-  
shaped coils, point the wand towards the screen).  
3. Enter the Run 21 game screen and adjust the RGB  
DRIVE controls until the playing cards are white  
and the speed bonus box is gray.  
To adjust vertical and horizontal control:  
3. Move the coil in a circular motion around the face  
of the monitor and slowly approach the game.  
Press TEST SCREENon the Megatouch Setup”  
screen.  
4. Continuing to move the coil in a circular motion,  
slowly back away from the monitor.  
A crosshair will appear on the screen. Change the  
DIP switch settings until the horizontal and vertical  
lines of the crosshair meet in the middle.  
5a. CIRCULAR-SHAPED COILS: When you are about  
three feet away, quickly turn the coil perpendicular  
to the monitor and release the trigger.  
5b. WAND-SHAPED COILS: When you are about  
three feet away, point the wand away from the  
monitor and release the trigger.  
2
MEGATOUCH SUPER IV MANUAL  
PM0070-0C  
 
COPYRIGHT 1996 MERIT INDUSTRIES, INC.  
Maintenance  
Troubleshooting  
Cleaning the Cabinet  
Security Key Error Messages  
The cabinet should be cleaned with a damp cloth  
and mild detergent.  
KEY NOT VALIDmessage means the security key  
is missing  
KEY QUESTION SET ERRORmessage means the  
security key does not match the  
chip set.  
Cleaning the Touchscreen Monitor  
The touchscreen monitor should be cleaned with a  
damp cloth and mild detergent.  
Coin Jam  
To gain access to the entire surface of the monitor  
screen on the upright model, you will have to release the  
monitor door latches. To do so, open the coin mech  
door. Located inside, above and to the right and left of  
the coin mech, are two monitor door latches. Unsnap the  
monitor door latches and lift the door upwards. See  
Figure 9.  
The game also has coin jam and stringing detection  
software. Should a coin become jammed in the mech  
or someone tries to string the mech, a continuous tone  
will be emitted by the game.  
If the game emits the coin jam indicator sound when  
powered up, this may indicate that the NORMALLY  
CLOSED contacts of the coin mechanism are being  
used. The NORMALLY OPEN contacts must be used.  
To gain access to the entire surface of the monitor  
screen on the cabaret model, you will have to release  
the monitor door latches. To do so, open the coin mech  
door. Located inside, above and to the right and left of  
the coin mech, are two monitor door slide-latches.  
Loosen the thumb nuts securing the latch and slide the  
latch open. Pull up on the bottom of the bezel to  
remove it (NOTE: TO FULLY REMOVE THE BEZEL,  
YOU MUST DISCONNECT THE GROUND BRAID).  
See Figure 6.  
To gain access to the entire surface of the monitor  
screen on the countertop model, you will have to  
remove the top of the machine. To remove the top of  
the machine, unlock and open the rear door. Locate the  
thumb nuts holding the lock brackets on each side of  
the monitor shelf. Unscrew and remove the thumb nuts  
and push the top forward. Pull upwards on the top to  
remove it from the machine. See Figure 5 for lock  
bracket locations.  
NOTE: DO NOT USE ANY ABRASIVE SOLVENTS, ACID OR  
VINEGAR-BASED CLEANSERS ON THE MONITOR OR  
SIDE DECALS. SUCH CLEANSERS COULD HARM THE  
TOUCHSCREEN AND ERASE THE DECALS OVER  
TIME. BE CAREFUL NOT TO USE COMMERCIAL  
CLEANERS CONTAINING ANY OF THESE  
SUBSTANCES.  
PM0070-0C  
MEGATOUCH SUPER IV MANUAL  
3
 
COPYRIGHT 1996 MERIT INDUSTRIES, INC.  
DIP Switch Settings  
Custom Program Versions  
Standard Program Settings  
Some of the options or features in the standard game  
may not be offered in certain jurisdictions. Depending  
upon the program version being used, the settings may  
differ slightly.  
The game contains one DIP switch. The DIP switch  
comes factory set. It determines which size monitor is  
being used, whether the machine displays quartersor  
creditsand controls video sync adjustment. These  
settings should not need to be changed.  
PROGRAM  
VERSION  
STANDARD  
VERSION  
MINNESOTA  
VERSION  
PROGRAM  
DIFFERENCES  
INCLUDES ALL OPTIONS  
NO RESTRICTIONS  
EXCLUDES CASINO  
GAMES  
PROGRAM #  
9255-41-01  
9255-41-02  
DIP SWITCH  
OFF  
ON  
19”  
EXCLUDES POKER  
DOUBLE-UP FEATURE &  
NO FREE GAME IN  
SOLITAIRE  
13“  
CALIFORNIA  
VERSION  
Position 1  
Position 2  
9255-41-06  
Touchscreen Touchscreen  
Quarters  
Credits  
NEW JERSEY  
VERSION  
INCLUDES 2-COIN LIMIT  
WITH LOCKOUT COIL  
SAME AS STANDARD  
VERSION, WITHOUT  
WORD/CASINO GAMES  
SAME AS STANDARD  
VERSION, WITHOUT  
WORD GAMES  
SAME AS STANDARD  
VERSION, WITHOUT  
WORD/CASINO GAMES  
SAME AS STANDARD  
VERSION, WITH NO FREE  
CREDIT  
SAME AS STANDARD  
VERSION W/SPECIAL  
QUESTION SET  
SAME AS STANDARD  
VERSION W/SPECIAL  
QUESTION SET  
9255-41-07  
9255-41-50  
Horizontal  
Horizontal  
Positions 5 & 6  
BI-LINGUAL  
ENG/GER  
Adjustment  
Vertical  
Adjustment  
Vertical  
Positions 7 & 8  
INTER-  
NATIONAL  
Adjustment  
Adjustment  
9255-41-57  
9255-41-60  
9255-41-62  
9255-41-70  
9255-41-72  
This adjusts the vertical and horizontal alignment of the picture. It is  
not an adjustment for touchscreen calibration.  
BI-LINGUAL  
ENG/FRE  
NO FREE  
CREDIT  
AUSTRALIA  
S. AFRICA  
4
MEGATOUCH SUPER IV MANUAL  
PM0070-0C  
 
COPYRIGHT 1996 MERIT INDUSTRIES, INC.  
To Enter This Screen, Press The SetupButton In The Coin Mech Section  
MEGATOUCH SETUP  
COIN-IN  
MENU  
GAME  
MENU  
DISPLAY  
BOOKS  
TEST  
SCREEN  
MORE  
OPTIONS  
CLEAR  
HI-SCORES  
DEFAULT  
YES  
YES  
ON  
2
NO  
NO  
SOLITAIRE BUY-IN  
FREE  
CREDIT  
SEX TOPICS IN WORD GAMES  
OFF BONUS GAME IN SOLITAIRE  
3
ROUNDS IN TRIVIA TWISTER  
BALLS IN BREAKIN BRICKS  
SIX STARS ENABLED  
3
3
4
NO  
NO  
NO  
NO  
NO  
YES  
YES  
YES  
YES  
YES  
CLEAR  
CREDIT  
PLAYER SELECTABLE LANGUAGE  
LANGUAGE ENGLISH/OTHER  
POWER SOL - SPLIT COLUMN  
SHOW ANSWERS IN TRIVIA  
TRIVIA ROUNDS/BONUS  
EXIT  
SETUP  
5/1M  
4/300k  
9255-41-01 12-11-1996 12:00:00  
Figure 1 - Megatouch Setup Screen  
Setup Screen Functions*  
More Options:  
Displays second pageof soft DIP switch settings (DIPs shown below dotted line are found on  
page 2 by touching More Options).  
Coin-In Menu:  
Game Menu:  
Display Books:  
Enters the coin/credit setup screen.  
Enters the game menu selection screen.  
Enters the bookkeeping statistics screen. (PC Dumplocated on the Books screen. PC Dump  
allows the books information to be downloadeed to a PC. Software for the PC is required for it  
to operate. Contact Merit Customer Service for information.  
Enters the touchscreen calibration test.  
Clears all game high scores.  
Adds credit without using coin switch. Free credits are listed separately in the books screen.  
All credits on the machine are erased.  
Test Screen:  
Clear Hi- Scores:  
Free Credit:  
Clear Credit:  
Exit Setup:  
Return to the attract mode.  
Six Stars Enabled  
This feature allows the high scores (for all active games) to be cleared, without opening the game. When the game  
is in attract mode and the screen is touched, the message Youve Got the Touch - Deposit Coins Nowwill appear  
on the screen; if the six stars enabledswitch is set to yes,six stars will appear at the top of this screen. Touch  
the stars in sequence to access the clear the high scores. To set the sequence in which the stars must be touched,  
go to the Clear Hi-Scoresscreen and follow the instructions. (Six Starswill not clear any tournament  
information.)  
*To save any changes, you must exit the Setup Screen before turning off the power. If the power is turned off before  
exiting this screen, the settings may be lost.  
PM0070-0C  
MEGATOUCH SUPER IV MANUAL  
5
 
COPYRIGHT 1996 MERIT INDUSTRIES, INC.  
To Enter This Screen, Press Game MenuIn The Setup Screen  
1 SOLITAIRE  
3 TRIVIA WHIZ  
5 TRI-TOWERS  
7 MEM-O-REE  
.25  
.25  
.25  
.25  
2 RUN 21  
.25  
.25  
.25  
4 MATCHEM UP  
6 FOURPLAY  
8 MORE GAMES…  
SOLITAIRE  
HORSES  
ROLL THE DICE  
PHRAZE CRAZE  
MATCHEM UP  
FOURPLAY  
11-UP  
RUN 21  
ROYAL FLASH  
TRIVIA TWISTER  
MEM-O-REE  
TRI-TOWERS  
POWER SOLITAIRE  
TRIVIA WHIZ  
DRAW POKER  
SUPER 7 STUD  
QUIKMATCH  
BREAKINBRICKS  
CONQUEST  
CLEAR  
ALL  
CLEAR  
1
FORMAT  
MENU 1  
EXIT  
DEFAULT  
Figure 2 - Game Menu Screen  
The game list and prices are programmed using this screen. Up to 21 games may be made  
available for the players to choose. The top of the screen shows the game positions available,  
with the price for each game. The lower section shows all games included in the program.  
Touching the icons on the bottom of the screen will clear the entire menu, clear a selected  
menu item, format the Game Menu to eliminate blanks, display Game Menus 2 and 3, reset  
the default game menu and pricing and exit the Game Menu screen.  
To program the Game Menu, select the menu position you want the game to occupy, by  
touching that position. Then touch the game name from the game list on the lower portion of  
the screen. That game will now appear in the menu. To adjust the price, touch the price in the  
game menu. Each touch will rotate the price from 25¢ (1CR), to 50¢ (2CR), to 75¢ (3CR), to  
$1 (4CR) and back to 25¢ (1CR). Touch EXITwhen done.  
6
MEGATOUCH SUPER IV MANUAL  
PM0070-0C  
 
COPYRIGHT 1996 MERIT INDUSTRIES, INC.  
To Enter This Screen, Press Coin-In MenuIn The Setup Screen  
COIN/CREDIT SETUP  
METER  
PULSES  
COIN  
INPUT  
COINS  
=
CREDITS  
&
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1E  
2E  
3E  
4E  
1M  
2M  
DEFAULT  
EXIT  
Figure 3 - Coin-In Menu Screen  
The coin/credit ratios of the game may be adjusted to meet any application. The CPU board supports up to six coin  
inputs: two mechanical mech inputs (1M and 2M) and four electronic mech inputs (1E, 2E, 3E and 4E). (Electronic coin  
mechs are typically used when more than one type of coin needs to be accepted. If you would like to convert your game  
from a mechanical mech to an electronic mech, please contact your distributor or Merit Technical Support for wiring  
details.)  
The coin/credit ratios can be adjusted by touching the screen at the location you want to change. The meter pulse can  
also be adjusted so that the coin meter can show the actual cash value of the coins in the cashbox, not just the total  
number of coins .  
Example: Lets say that in the country of Atlantis the currency is called units. Atlantis, however, has a 1 unit coin, a 2  
unit coin and a 5 unit coin. You decide that 1 credit on the game should cost 1 unit. However, to encourage more play  
you want to give 6 credits for a 5 unit coin. The coin setup screen would be programmed as follows:  
COIN  
INPUT  
1E  
2E  
3E  
METER  
PULSES  
COINS  
=
CREDITS  
&
1
1
1
1
2
6
1
2
5
For every 1 unit coin, the game would give 1 credit and count 1 pulse on the mechanical coin counter. For every 2 unit  
coin, the game would give 2 credits and count 2 pulses on the mechanical meter. For every 5 unit coin, the game would  
give 6 credits and pulse the mechanical meter 5 times. The mechanical meter will now display the total number of  
unitsin the cashbox, not total coins or credits. Press DEFAULTto return to the factory settings. Press EXITto  
return to the GAME SETUP menu.  
PM0070-0C  
MEGATOUCH SUPER IV MANUAL  
7
 
COPYRIGHT 1996 MERIT INDUSTRIES, INC.  
FIGURE 4 - 13COUNTERTOP (FRONT VIEW)  
FIGURE 5 - 13COUNTERTOP (REAR VIEW)  
8
MEGATOUCH SUPER IV MANUAL  
PM0070-0C  
 
COPYRIGHT 1996 MERIT INDUSTRIES, INC.  
FIGURE 6 - 19CABARET (FRONT VIEW)  
FIGURE 7 - 19CABARET (REAR VIEW)  
PM0070-0C  
MEGATOUCH SUPER IV MANUAL  
9
 
COPYRIGHT 1996 MERIT INDUSTRIES, INC.  
FIGURE 8 - 19UPRIGHT (FRONT VIEW)  
FIGURE 9 - 19UPRIGHT (REAR VIEW)  
10  
MEGATOUCH SUPER IV MANUAL  
PM0070-0C  
 
COPYRIGHT 1996 MERIT INDUSTRIES, INC.  
MEGATOUCH IV PARTS LISTS  
COUNTERTOP  
REF #  
X
QUANTITY  
PART NO.  
EC2001  
DESCRIPTION  
1
1
2
1
1
2
1
1
1
1
1
1
1
2
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
2
POWER CORD, 120V  
X
EC2002  
POWER CORD, 240V  
X
GL3000-XX  
MW5165-01  
MW5167-01  
MW5151-01  
MW5150-01  
HW8018-01  
HW8993-02  
HW9001  
DECAL, MEGATOUCH, (-01=RT;-02=LT)  
MONITOR FILLER PLATE  
LOCK BRACKET, REAR DOOR  
MONITOR SUPPORT  
1
2
3
4
MAIN CHASSIS  
5
RUBBER ANTI-SKID PAD  
LAZY SUSAN, 12DIAMETER, 15 DEG STOPS  
PLASTIC TUBING  
6
7
8
SA5151-01  
EC9359  
TOUCHSCREEN/CRT ASSEMBLY  
CRT, COLOR, 14CGA, WITH FRAME  
TOUCHSCREEN OVERLAY  
LID, RETAINING BRACKET  
LID, LOCK BRACKET, RIGHT  
LID, LOCK BRACKET, LEFT  
REAR DOOR  
9
10  
11  
12  
13  
14  
16  
17  
18  
19  
20  
21  
22  
23  
24  
25  
26  
27  
28  
30  
31, 32  
33  
34  
35  
36  
EC9824  
MW5155-01  
MW5159-01  
MW5159-02  
MW5161-01  
MW5164-01  
HW8713  
HINGE, REAR DOOR  
FLAT LOCK #564 (REAR DOOR)  
CABINET SIDE, RIGHT  
WD5171-01  
WD5171-02  
EC9154  
CABINET SIDE, LEFT  
COUNTER, 12V, FROG EYE MOUNTING  
AC POWER HARNESS  
SA5123-01  
SA5131-01  
HW8953  
MAIN HARNESS  
BEZEL, 13T/S  
SA4084  
4SPEAKER ASSEMBLY  
POWER SUPPLY, SW, 11 AMP  
RETAINING BRACKET, COIN BOX  
PCA, CPU, VID, 260 TESTED  
SMT-3 TOUCHSCREEN CONTROLLER  
CIRCULAR LOCK (COIN MECH)  
CONNECTOR COIN BOX ASSEMBLY  
COIN BOX ASSEMBLY  
EC7526-02  
MW5156-01  
TA10004-02  
EC9840  
HW8741  
SA5156-01  
SA5153-01  
HW8727  
LOCK, COIN BOX  
MW5153-01  
HW4498  
LID, COIN BOX  
THUMB SCREWS, BRASS  
POWER ENTRY (POWER ENTRY TYPE DETERMINED BY  
LINE CORD REQUIREMENTS)  
37  
1
SA5152-XX  
38  
39  
1
1
SB0004-02*  
HW0001-01  
ASSY, MOV/ARRESTOR (*240V GAMES ONLY)  
SAFETY COVER, POWER SUPPLY  
PM0070-0C  
MEGATOUCH SUPER IV MANUAL  
11  
 
COPYRIGHT 1996 MERIT INDUSTRIES, INC.  
19” CABARET  
REF#  
QUANTITY  
PART NO.  
DESCRIPTION  
X
X
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
2
1
1
1
1
1
1
1
1
1
1
1
1
1
1
EC2001  
EC2002  
POWER CORD, 120V  
POWER CORD, 240V  
1
WD5060-01  
MW1672-01  
MW1673-01  
MW1671-01  
HW8951-01  
SA3266-02  
SA3263-01  
SA3270-01  
SA4084  
WOOD CABINET, URTS, 19CABARET  
CONTROL PANEL, 19CABARET  
COVER SCREEN, 19CABARET  
BRKT, GLASS, UPPER, 19CABARET  
BEZEL, MONITOR, 19CABARET  
CRT ASSY, 19CABARET  
2
3
4
5
6
7
POWER ENTRY, URTS, 120V  
POWER ENTRY, URTS, 240V  
SPEAKER ASSY, 4”  
7
8
9
SA3209-01  
SA3281-01  
TA10004-02  
SA3282-01  
EC7526-02  
WD5052-01  
SA3264-01  
SB1523-02  
EC6052-04  
GL2401-03  
GL2411-03  
GL2999-01  
MW1674-01  
MW1674-02  
HW8979  
BRKT ASSY, METER/TEST SW  
MAIN HARNESS, 19CABARET  
PCA, CPU, VID, 260  
10  
11  
12  
13  
14  
15  
16  
17  
18  
19  
20  
21  
22  
23  
24  
25  
26  
27  
30  
31  
32  
33  
28  
29  
30  
POWER HARNESS, 19CABARET  
POWER SUPPLY  
PC SHELF, CABARET  
SWITCH ASSY, URTS  
FLUORESCENT LAMP ASSY, 120V, 22”  
FLUOR, 15, 120V-60Hz, W/10CABLE  
VINYL, MARQ, MEGATOUCH 19CABARET  
PLEXI, CLR, 19CABARET SIGN  
DECAL, MEGATOUCH, URTS, CABARET  
MONITOR SUPPORT, LEFT, 19CAB  
MONITOR SUPPORT, RIGHT, 19CAB  
SLIDE LATCH, DART MATRIX SW  
COVER, SPEAKER HOLE, 19CABARET  
MOUNTING POST, KNURLED  
LAMP, FLUOR, 15: F15T8CW  
HW1677-01  
HW6366  
LB2100  
EC9840  
SMT-3 TOUCHSCREEN CONTROL MODULE  
SPEAKER, MTG BRKT, 19CAB  
CRT, COLR, 20, CGA, DC COUPLED  
OVRLY, T/S 19W/58CABLE  
SHELF, MONITOR 19CAB  
MW1670-01  
EC9374  
EC9839  
WD5061-01  
MW0006-01*  
SB0004-02*  
HW0001-01  
COVER, PCA (*240V GAMES ONLY)  
ASSY, MOV/ARRESTOR (*240V GAMES ONLY)  
SAFETY COVER, POWER SUPPLY  
12  
MEGATOUCH SUPER IV MANUAL  
PM0070-0C  
 
COPYRIGHT 1996 MERIT INDUSTRIES, INC.  
19UPRIGHT  
REF#  
QUANTITY  
PART NO.  
DESCRIPTION  
X
X
1
1
1
1
4
2
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
EC2001  
EC2002  
POWER CORD, 120V  
POWER CORD, 240V  
1
HW8711  
ANCHOR PLATE FOR CAM LOCK  
FLAT LOCK, #564  
2
HW8716  
3
HW8960  
LEG LEVELER  
4
MW0044-01  
SA3230-01  
MW5006-01  
SA0015-01  
SA3216-01  
EC7526-02  
TA10004-02  
SA3202-04  
WD2014-01  
SA3210-02  
EC9374  
DOOR LOCK PLATE, URTB  
5
BEZEL ASSEMBLY  
6
SPEAKER COVER  
7
HARNESS, MAIN, UNIVERSAL, 19CAB/URTS  
AC POWER HARNESS  
8
9
POWER SUPPLY  
10  
11  
12  
13  
14  
15  
16  
17  
18  
19  
19  
20  
21  
23  
24  
25  
26  
27  
PCA, CPU, VID, 260  
SHELF ASSEMBLY, TOUCHSCREEN/CRT, 120V  
PCB MOUNTING SHELF  
TOUCHSCREEN/CRT ASSEMBLY  
CRT, COLOR, 19CGA  
EC9823  
TOUCHSCREEN OVERLAY, 19”  
CRT MOUNTING SHELF  
WD2013-01  
MW5003-01  
MW5003-02  
SA3206-01  
SA3170-01  
SA4084  
CRT ADJUST, BRACKET, LEFT  
CRT ADJUST, BRACKET, RIGHT  
POWER ENTRY, UR 19, T/S, 120V  
POWER ENTRY, UR 19, T/S, 240V  
SPEAKER ASSEMBLY  
WD2012-01  
SA3209-01  
EC9840  
CABINET, 19UPRIGHT TOUCHSCREEN  
METER/TEST SWITCH BRACKET ASSEMBLY  
SMT-3 TOUCHSCREEN CONTROL MODULE  
COVER, PCA, 19URTS/CAB (*240V GAMES ONLY)  
ASSY, MOV/ARRESTOR (*240V GAMES ONLY)  
SAFETY COVER, POWER SUPPLY  
MW0006-01*  
SB0004-02*  
HW0001-01  
PM0070-0C  
MEGATOUCH SUPER IV MANUAL  
13  
 
COPYRIGHT 1996 MERIT INDUSTRIES, INC.  
Merit Video  
Limited Warranty  
Merit Industries, Inc. warrants its video countertop and  
upright machines to be free from defects in material  
and workmanship for a period of six months from the  
date of delivery or seven months from the date of  
shipment from its facilities, whichever occurs first. The  
warranty covers all electrical components (except fuses  
and light bulbs) and printed circuit boards. Other items  
are covered by warranty periods offered by the original  
equipment manufacturers (power supplies - 90 days;  
video monitors - 90 days).  
In certain instances, due to geographical or other  
considerations, Merit may offer PCB warranty service  
on an extended time basis as follows:  
(a) User notifies Merit in writing (or FAX) of PCB  
failure, providing dates of failure, serial numbers  
and a brief description of failure symptoms.  
(b) Failed PCBs are accumulated for a time  
period or quantity accumulation, as designated  
by Merit and sent in one shipment to save  
shipping expenses.  
Failure due to misuse, vandalism, excessive or  
intentional abuse, operation outside specified  
conditions (including, but not limited to, improper  
electrical power source), fire, water damage, acts of  
God, acts of war and civil unrest are specifically  
excluded.  
(c) Merit honors warranty as per dates of failure  
notification.  
The above terms and conditions constitute the sole  
obligation, written or implied, of Merit Industries under  
its warranty coverage.  
Merit products are carefully inspected and thoroughly  
tested prior to packing and shipment. Any damage  
discovered upon receipt of goods, whether obvious or  
concealed, must be reported immediately to the  
delivering carrier and claims made directly to them.  
Merit assumes no responsibility for damages once the  
product has left its facilities and any disputes regarding  
transportation damage must be resolved with the  
shipping company(s).  
PROPRIETARY  
Merit will repair or replace, at its option, any  
THE INFORMATION CONTAINED HEREIN IS THE  
EXCLUSIVE PROPERTY OF MERIT INDUSTRIES,  
INCORPORATED AND SHALL NOT BE USED,  
DISTRIBUTED OR REPRODUCED IN WHOLE, OR IN  
PART, WITHOUT THE EXPRESS WRITTEN  
PERMISSION OF MERIT INDUSTRIES,  
component, part or assembly that fails under warranty,  
provided that the failed item is returned, shipping  
charges prepaid, to Merits repair facility and Merit is  
notified of the failure within the warranty period. Merit  
reserves the right to request the serial numbers of the  
item and/or game which has failed , and copies of sales  
invoices, bills of lading or other documents as required  
to determine the validity of the warranty coverage. Merit  
will return or replace warranty items, as specified  
above, shipping charges prepaid, by ground  
transportation.  
INCORPORATED.  
FCC WARNING  
Merits obligation shall be limited to repair or  
replacement as stated above, and shall specifically  
exclude any liability for consequential damages or loss  
of earnings.  
THIS EQUIPMENT COMPLIES WITH THE  
REQUIREMENTS IN PART 15 OF FCC RULES FOR  
A CLASS ACOMPUTING DEVICE. OPERATION IN  
A RESIDENTIAL AREA MAY CAUSE  
INTERFERENCE TO RADIO AND TV RECEPTION  
REQUIRING THE OPERATOR TO TAKE WHATEVER  
STEPS ARE NECESSARY TO CORRECT THE  
INTERFERENCE.  
Merit may, at its discretion, provide replacement parts  
under warranty prior to receiving defective items  
without incurring any ongoing obligation to extend such  
accommodations.  
14  
MEGATOUCH SUPER IV MANUAL  
PM0070-0C  
 

EdgeStar Dishwasher DWP45E User Manual
EdgeStar Ice Maker IB1000SS User Manual
Eiki Projector EIP 3000NA User Manual
Faber Indoor Fireplace CADRA NOVA User Manual
Fender Guitar American Deluxe Jazz Bass User Manual
Fisher Price Baby Toy X6172 User Manual
Gateway Computer Monitor FPD1785 User Manual
GBC Binding Machine 15 User Manual
GBC Photo Printer H 950 User Manual
Global Machinery Company Drill MX1G100 User Manual