Instructions–Parts List
1:1 RATIO
TRITONR 308
309303V
ENG
Diaphragm Pump
Used to pump waterborne and solvent–based paints and catalysts. For
professional use only.
115 psi (0.8 MPa, 8 bar) Maximum Fluid Working Pressure
115 psi (0.8 MPa, 8 bar) Maximum Air Input Pressure
Part No. 233500 Aluminum Pump, Series D, npt threads
Part No. 233501 Stainless Steel Pump, Series C, npt threads
Part No. 233776 Aluminum Pump, Series C, BSPP threads
Part No. 233777 Stainless Steel, Series C, BSPP threads
U.S. and Foreign Patents Pending
Important Safety Instructions
Read all warnings and instructions in this manual.
Save these instructions.
ti1029a
Part No. 233501 Shown
WARNING
EQUIPMENT MISUSE HAZARD
Equipment misuse can cause the equipment to rupture, malfunction, or start unexpectedly and result
in a serious injury.
INSTRUCTIONS
D
T
h
i
s
e
q
u
i
p
m
e
n
t
i
s
f
o
r
p
r
o
f
e
s
s
i
o
n
a
l
u
s
e
o
n
l
y
.
D Read all instruction manuals, tags, and labels before operating the equipment.
D Use the equipment only for its intended purpose. If you are not sure, call your Graco distributor.
D Do not alter or modify this equipment. Use only genuine Graco parts and accessories.
D Check equipment daily. Repair or replace worn or damaged parts immediately.
D Do not exceed the maximum working pressure of the lowest rated component in your system. This
equipment has a 115 psi (0.8 MPa, 8 bar) maximum working pressure at 115 psi (0.8 MPa, 8
bar) maximum incoming air pressure.
D Use fluids and solvents which are compatible with the equipment wetted parts. Refer to the Tech-
nical Data section of all equipment manuals. Read the fluid and solvent manufacturer’s warnings.
D Aluminum pumps only: Never use 1.1.1–trichloroethane, methylene chloride, other halogenated
hydrocarbon solvents or fluids containing such solvents in pressurized aluminum equipment. Such
use could result in a chemical reaction, with the possibility of explosion.
D
D
o
n
o
t
u
s
e
h
o
s
e
s
t
o
p
u
l
l
e
q
u
i
p
m
e
n
t
.
D Route hoses away from traffic areas, sharp edges, moving parts, and hot surfaces. Do not expose
Graco hoses to temperatures above 180_ F (82_ C) or below –40_ F (–40_ C).
D
W
e
a
r
h
e
a
r
i
n
g
p
r
o
t
e
c
t
i
o
n
w
h
e
n
o
p
e
r
a
t
i
n
g
t
h
i
s
e
q
u
i
p
m
e
n
t
.
D
C
o
m
p
l
y
w
i
t
h
a
l
l
a
p
p
l
i
c
a
b
l
e
l
o
c
a
l
,
s
t
a
t
e
,
a
n
d
n
a
t
i
o
n
a
l
f
i
r
e
,
e
l
e
c
t
r
i
c
a
l
,
a
n
d
s
a
f
e
t
y
r
e
g
u
l
a
t
i
o
n
s
.
309303
3
WARNING
FIRE AND EXPLOSION HAZARD
Improper grounding, poor air ventilation, open flames, or sparks can cause a hazardous condition and
result in fire or explosion and serious injury.
D
G
r
o
u
n
d
t
h
e
e
q
u
i
p
m
e
n
t
.
R
e
f
e
r
t
o
G
r
o
u
n
d
i
n
g
o
n
p
a
g
e
7
.
D If there is any static sparking or you feel an electric shock while using this equipment, stop pump-
ing immediately. Do not use the equipment until you identify and correct the problem.
D
P
r
o
v
i
d
e
f
r
e
s
h
a
i
r
v
e
n
t
i
l
a
t
i
o
n
t
o
a
v
o
i
d
t
h
e
b
u
i
l
d
u
p
o
f
f
l
a
m
m
a
b
l
e
f
u
m
e
s
f
r
o
m
s
o
l
v
e
n
t
s
o
r
t
h
e
f
l
u
i
d
being pumped.
D Keep the work area free of debris, including solvent, rags, and gasoline.
D Electrically disconnect all equipment in the work area.
D Extinguish all open flames or pilot lights in the work area.
D Do not smoke in the work area.
D Do not turn on or off any light switch in the work area while operating or if fumes are present.
D Do not operate a gasoline engine in the work area.
4
309303
WARNING
PRESSURIZED FLUID HAZARD
Spray from the gun, hose leaks, or ruptured components can splash fluid in the eyes or on the skin
and cause serious injury.
D
D
o
n
o
t
s
t
o
p
o
r
d
e
f
l
e
c
t
f
l
u
i
d
l
e
a
k
s
w
i
t
h
y
o
u
r
h
a
n
d
,
g
l
o
v
e
,
o
r
r
a
g
.
D
F
o
l
l
o
w
t
h
e
P
r
e
s
s
u
r
e
R
e
l
i
e
f
P
r
o
c
e
d
u
r
e
o
n
p
a
g
e
1
1
b
e
f
o
r
e
c
l
e
a
n
i
n
g
,
c
h
e
c
k
i
n
g
,
o
r
s
e
r
v
i
c
i
n
g
t
h
e
equipment.
D
T
i
g
h
t
e
n
a
l
l
f
l
u
i
d
c
o
n
n
e
c
t
i
o
n
s
b
e
f
o
r
e
e
a
c
h
u
s
e
.
D
C
h
e
c
k
t
h
e
h
o
s
e
s
,
t
u
b
e
s
,
a
n
d
c
o
u
p
l
i
n
g
s
d
a
i
l
y
.
R
e
p
l
a
c
e
p
a
r
t
s
i
m
m
e
d
i
a
t
e
l
y
i
f
w
o
r
n
,
d
a
m
a
g
e
d
,
o
r
loose. Permanently coupled hoses cannot be repaired.
TOXIC FLUID HAZARD
Hazardous fluids or toxic fumes can cause a serious injury or death if splashed in the eyes or on the
skin, swallowed, or inhaled.
D
K
n
o
w
t
h
e
s
p
e
c
i
f
i
c
h
a
z
a
r
d
s
o
f
t
h
e
f
l
u
i
d
y
o
u
a
r
e
u
s
i
n
g
.
R
e
a
d
t
h
e
f
l
u
i
d
m
a
n
u
f
a
c
t
u
r
e
r
’
s
w
a
r
n
i
n
g
s
.
D
S
t
o
r
e
h
a
z
a
r
d
o
u
s
f
l
u
i
d
i
n
a
n
a
p
p
r
o
v
e
d
c
o
n
t
a
i
n
e
r
.
D
i
s
p
o
s
e
o
f
t
h
e
h
a
z
a
r
d
o
u
s
f
l
u
i
d
a
c
c
o
r
d
i
n
g
t
o
a
l
l
local, state, and national guidelines.
D Wear appropriate protective clothing, gloves, eyewear, and respirator.
D If the diaphragm fails, the fluid is exhausted along with the air.
309303
5
Installation
General Information
WARNING
D Fig. 2 shows a wall mounted HVLP spray applica-
tion. It is only a guide for selecting and installing
system components. Contact your Graco distributor
for assistance in planning a system to suit your
needs.
FIRE AND EXPLOSION HAZARD
To prevent hazardous concentrations of
toxic and/or flammable vapors, spray
only in a properly ventilated spray booth.
Never operate the spray gun unless
ventilation fans are operating.
D Always use Genuine Graco Parts and Accessories,
available from your Graco distributor. If you supply
your own accessories, be sure they are adequately
sized and pressure rated for your system.
Check and follow all of the national,
state, and local codes regarding air
exhaust velocity requirements.
D Use a compatible, liquid thread sealant on all male
threads. Tighten all connections firmly to avoid air
or fluid leaks.
WARNING
TOXIC FLUID HAZARD
NOTE: On all npt threads, tighten to 2–3 turns past
finger tight.
Hazardous fluid or toxic fumes can
cause serious injury or death if splashed
in the eyes or on the skin, inhaled, or
swallowed.
D Reference numbers and letters in parentheses refer
to the callouts in the figures and the parts lists on
pages 23–22.
1. Read TOXIC FLUID HAZARD on page 5.
2. Use fluids and solvents which are compatible
with the equipment wetted parts. Refer to the
Technical Data section of all equipment manu-
als. Read the fluid and solvent manufacturer’s
warnings.
D
I
n
a
s
p
r
a
y
s
y
s
t
e
m
,
v
e
n
t
i
l
a
t
e
t
h
e
s
p
r
a
y
b
o
o
t
h
.
Tightening Threaded Fasteners Before
First Use
Mounting the Pump
NOTE: Before using pump, loosen fluid cover screws
(38) 1–2 turns and then retorque to 13.6 NSm
(10 ft–lb).
D Mount the pump in a well-ventilated area, with
sufficient clearance on all sides for operator access
and servicing.
See the Service section for torque specifications.
D Be sure the mounting can support the weight of the
pump, hoses, and accessories, as well as the
stress caused during operation.
D After unpacking the pump, and before using it for
the first time, check and retorque all external fas-
teners.
D
T
h
e
p
u
m
p
m
a
y
b
e
m
o
u
n
t
e
d
v
e
r
t
i
c
a
l
l
y
o
r
h
o
r
i
z
o
n
t
a
l
-
ly. Be sure the pump is level in all directions.
D
After the first day of operation, retorque the fasten-
ers.
D Wall, pail, stand, or portable cart mounting kits are
available from Graco. For other mountings, be sure
the pump is adequately secured. The pump has
two mounting holes for 0.35 in. (9 mm) screws. See
the Dimension drawing on page 25.
D
A
s
a
g
e
n
e
r
a
l
g
u
i
d
e
l
i
n
e
,
r
e
t
o
r
q
u
e
f
a
s
t
e
n
e
r
s
e
v
e
r
y
two months.
6
309303
Installation
Grounding
35
Y
WARNING
FIRE AND EXPLOSION HAZARD
This pump must be grounded. Before
operating the pump, ground the system
as explained below. Also read the sec-
tion FIRE AND EXPLOSION HAZARD
on page 4.
ti1030b
To reduce the risk of static sparking, ground the pump
and all other equipment used or located in the pumping
area. Check your local electrical code for detailed
grounding instructions for your area and type of equip-
ment.
Fig. 1
D
A
i
r
a
n
d
f
l
u
i
d
h
o
s
e
s
:
U
s
e
o
n
l
y
e
l
e
c
t
r
i
c
a
l
l
y
c
o
n
d
u
c
t
i
v
e
hoses.
D
A
i
r
c
o
m
p
r
e
s
s
o
r
:
F
o
l
l
o
w
t
h
e
m
a
n
u
f
a
c
t
u
r
e
r
’
s
r
e
c
o
m
-
mendations.
Ground all of this equipment:
D Solvent pails used when flushing: Follow your local
code. Use only metal pails, which are conductive.
Do not place the pail on a non-conductive surface,
such as paper or cardboard, which interrupts the
grounding continuity.
D Pump: Attach a ground wire (Y) to the pump’s
grounding screw (35) and secure with the screw, as
shown in Fig. 1. Connect the clamp end of the
ground wire to a true earth ground. Order Part No.
238909 Ground Wire and Clamp.
D
F
l
u
i
d
s
u
p
p
l
y
c
o
n
t
a
i
n
e
r
:
F
o
l
l
o
w
y
o
u
r
l
o
c
a
l
c
o
d
e
.
309303
7
Installation
b. Locate a bleed-type master air valve (B) close
Air Line
to the pump, to relieve trapped air. See the
WARNING at left. Locate another air valve (E)
upstream from all air line accessories, to
isolate them during cleaning and repair.
WARNING
A bleed-type master air valve (B) is required in your
system to relieve air trapped between this valve
and the pump. See Fig. 2. Trapped air can cause
the pump to cycle unexpectedly, which could result
in serious injury, including splashing in the eyes or
on the skin, injury from moving parts, or contamina-
tion from hazardous fluids.
c. Install an air line filter (D) to remove harmful
contaminants such as dirt, moisture, and oil
from the compressed air supply.
2. The air valve does not require lubrication.
1. Install the air line accessories as shown in Fig. 2.
Mount these accessories on the wall or on a
bracket. Be sure the air line supplying the acces-
sories is electrically conductive.
3. Install an electrically conductive, flexible air hose
(C) between the accessories and the pump air inlet
(T). Use a minimum 1/4” (6.3 mm) ID air hose.
Screw an air line quick disconnect coupler (V) onto
the end of the air hose and screw the mating fitting
into the pump air inlet snugly. Do not connect the
coupler to the fitting yet.
a. The fluid pressure can be controlled in two
ways, either by controlling the air into the
pump with the air regulator (F) or the fluid out
of the pump with the fluid regulator (H).
8
309303
Installation
Wall Mount HVLP Spray Installation Shown
KEY
A
B
TRITON 308 Pump
Bleed-type master air valve
(required for pump)
C
D
E
F
Air supply line
Air line filter
Air line shutoff valve
Pump air regulator
G
H
Gun air regulator (used in spray system only)
Fluid pressure regulator (used in spray
system only)
S
J
K
L
M
N
P
Drain/circulation valve
Drain tube
Suction tube
Pump fluid inlet
Pump fluid outlet
H
J
Y
R
E
D
Fluid hose (shown connected to gun in spray
system)
R
S
T
Gun air hose (used in spray system only)
Spray gun (used in spray system only)
Pump air inlet
U
V
Y
Agitator (used in spray system only)
Air line quick disconnect
Ground wire
P
B
V
C
L
U
Y
K
J
H
N
K
ti1020a
G
T
F
A
M
L
B
ti1007a
Fig. 2
309303
9
Installation
Fluid Suction Line
CAUTION
Some systems may require installation of a pressure
relief valve at the pump outlet to prevent overpres-
surization and rupture of the pump or hose.
D Screw the suction line (L) into the pump inlet (M)
snugly. Use a compatible liquid thread sealant on
connections to prevent air from getting into the fluid
line.
Thermal expansion of fluid in the outlet line can
cause overpressurization. This can occur when using
long fluid lines exposed to sunlight or ambient heat,
or when pumping from a cool to a warm area (for
example, from an underground tank).
D
D
o
n
o
t
p
r
e
s
s
u
r
e
f
e
e
d
t
h
i
s
p
u
m
p
.
D
S
e
e
t
h
e
T
e
c
h
n
i
c
a
l
D
a
t
a
o
n
p
a
g
e
2
4
f
o
r
m
a
x
i
m
u
m
suction lift.
Overpressurization can also occur if the pump is
being used to feed fluid to a piston pump, and the
intake valve of the piston pump does not close,
causing fluid to back up in the outlet line.
D Use an agitator (U) to prevent fluid from settling
out. Part No. 245081 Agitator Kit (accessory) is
available.
D
U
s
e
e
l
e
c
t
r
i
c
a
l
l
y
c
o
n
d
u
c
t
i
v
e
f
l
u
i
d
h
o
s
e
s
(
P
)
.
S
c
r
e
w
the fluid fitting into the pump outlet (N) snugly.
Fluid Outlet Line
D Install a fluid regulator (H) at the pump fluid outlet
to control fluid pressure, if desired. See Air Line,
step 1a, for another method of controlling pressure.
WARNING
A fluid drain valve (J) is required in your system to
relieve pressure in the hose if it is plugged. See
Fig. 2. The drain valve reduces the risk of serious
injury, including splashing in the eyes or on the
skin, or contamination from hazardous fluids when
relieving pressure. Install the valve close to the
pump fluid outlet. To use the valve as a circulation
valve, connect a tube (K) between the valve and
pail.
D Install a fluid drain valve (J) near the fluid outlet.
See the WARNING at left.
Flush the Pump Before First Use
The pump was tested in lightweight oil. If the oil could
contaminate the fluid you are pumping, flush the pump
thoroughly with a compatible solvent. Follow the steps
under Starting and Adjusting the Pump on page 11.
10
309303
Operation
4. Check all fittings to be sure they are tight. Use a
Pressure Relief Procedure
compatible liquid thread sealant on all male
threads. Tighten the fluid inlet and outlet fittings
snugly. Do not overtighten the fittings.
WARNING
NOTE: Before using he pump, re–torque fluid
cover screws (38) to 10 ft–lb (13.6 NSm).
The system remains pressurized until pressure is
manually relieved. To reduce the risk of serious
injury from pressurized fluid, accidental spray from
the gun, or splashing of any fluid, follow this proce-
dure whenever you
5. Place the suction tube (L, if used) in the fluid to be
pumped.
D
S
t
o
p
s
p
r
a
y
i
n
g
6. Place the fluid hose (P) in a container.
7. Close the drain/circulation valve (J).
D Are instructed to relieve pressure
D Check or service any system equipment
D Install, clean, or change spray nozzles
8. Close the pump air regulator (F). Open all bleed-
type master air valves (B, E).
1. Shut off the bleed-type air valve (B).
2. In a spray system, hold the gun (S) firmly against a
grounded metal pail and trigger the gun to relieve
the fluid pressure.
9. If the fluid hose has a dispensing device, hold it
open while continuing with the following step.
Slowly open the air regulator (F) until the pump
starts to cycle. Allow the pump to cycle slowly until
all air is pushed out of the lines and the pump is
primed.
3. Place the drain tube (K) in a waste pail. Open the
drain/circulation valve (J) to relieve any fluid pres-
sure trapped in the system.
If you are flushing, run the pump long enough to
thoroughly clean the pump and hoses. Close the
air regulator. Remove the suction tube from the
solvent and place it in the fluid to be pumped.
Starting and Adjusting the Pump
Read Toxic Fluid Hazard
1.
on page 5.
Pump Shutdown
If lifting the pump, follow the Pres-
sure Relief Procedure above.
2.
WARNING
To reduce the risk of serious injury whenever you
are instructed to relieve pressure, always follow the
Pressure Relief Procedure at left.
Be sure the pump is
properly grounded.
Read Fire and
3.
Explosion Hazard
on page 4.
At the end of the work shift, flush the pump and relieve
pressure.
309303
11
Maintenance
Tightening Threaded Connections
Storage
Before each use, check all hoses for wear or damage.
Replace as necessary. Check that all threaded con-
nections are tight and leak-free.
Before storing the pump, always flush it and relieve
pressure.
NOTE: Periodically, re–torque fluid cover screws (38)
to 10 ft–lb (13.6 NSm).
Preventive Maintenance Schedule
Establish a preventive maintenance schedule, based
on the pump’s service history. This is especially impor-
tant for prevention of spills or leakage due to dia-
phragm failure.
Cleaning
Clean the outside of the equipment daily, using a soft
cloth and compatible solvent.
Clean the suction tube (L) and inlet strainer daily, using
a compatible solvent.
Clean the air filter (D) in your main air line at least
once a week.
Troubleshooting
1. Relieve the pressure before checking or servicing
WARNING
the equipment.
To reduce the risk of serious injury whenever you
are instructed to relieve pressure, always follow the
Pressure Relief Procedure on page 11.
2. Check all possible problems and causes before
disassembling the pump.
PROBLEM
Pump will not run.
CAUSE
Closed air line valve.
SOLUTION
Open valve.
Inadequate air supply, or clogged/
restricted air line.
Increase air supply. Do not exceed
maximum air inlet pressure.
Open or clear air line.
Clean air filter.
Clogged pump, fluid line, or spray
gun.
Clear, service. Flush regularly. Do
not allow fluid to set up in the pump
and lines.
Stuck or damaged pump air valve.
Disassemble and clean air valve.
Replace worn parts. See page 18.
Use filtered air.
Ruptured diaphragm.
Replace diaphragms. See page 17.
Air valve plate installed incorrectly.
Align plate with center housing. See
page 19.
12
309303
Troubleshooting
PROBLEM
Pump runs sluggishly.
Pump runs erratically.
CAUSE
SOLUTION
Worn or damaged carriage o-rings. Service air valve. See page 18.
Clogged suction line or inlet strainer. Clear.
Sticking or leaking ball check
valves.
Disassemble and clean ball checks.
Replace worn parts. See page 16.
Pump runs too fast.
Exhausted fluid supply.
Worn ball check valves.
Worn air valve cup or plate.
Refill fluid supply and prime pump.
Pump cycles at stall or fails to hold
pressure at stall.
Disassemble and clean ball checks.
Replace worn parts. See page 16.
Audible air leak.
Service air valve. See page 18.
Air exhausting from the mounting
holes.
Fluid covers are installed incorrectly. Align mounting holes in fluid covers
with holes in center housing. See
page 14.
Fluid in the exhaust air.
Air bubbles in fluid.
Ruptured diaphragm.
Loose suction line.
Replace diaphragms. See page 17.
Tighten. Use a compatible liquid
thread sealant on connections.
Ruptured diaphragm.
Replace diaphragms. See page 17.
Poor finish or irregular spray pat-
tern.
Incorrect fluid or air pressure at gun. See gun manual; read fluid
manufacturer’s recommendations.
Use fluid regulator.
Fluid is too thin or too thick.
Adjust fluid viscosity; read fluid
manufacturer’s recommendations.
Dirty, worn, or damaged spray gun. Service gun.
Fluid is settling out. Use agitator. Order Part No. 245081
Agitator Kit.
309303
13
Service
3. Remove the pump from its mounting.
Remove the Fluid and Side Covers
Tools Required
CAUTION
D
T
o
r
q
u
e
w
r
e
n
c
h
Be careful that the ball checks do not fall out when
you remove the fluid covers (32).
D 2.5 mm allen wrench
D 6 mm allen wrench
D Adjustable wrench
4. Remove the six screws (38) and top cover (32)
from the center housing (1). Remove the ball
check seals (24). Remove the bottom cover and
seals.
Disassembly
WARNING
To reduce the risk of serious injury whenever you
are instructed to relieve pressure, always follow the
Pressure Relief Procedure on page 11.
NOTE: Always replace the ball check seals (24) when-
ever the fluid covers (32) are removed. These seals
are included in the four repair kits.
NOTE: Perform step 5 only if you are servicing the air
valve or the diaphragm shaft.
1. Relieve the pressure.
5. Remove the two screws (39) and take off the side
cover (31) and felt dampener (29).
2. Disconnect the hoses and ground wire.
14
309303
Service
Remove the Fluid and Side Covers
(continued)
1
Align
3
4
10 ft-lb (13.6 NSm)
2
28 in-lb (3.1 NSm)
Replace seals whenever
cover (32) is removed.
Reassembly
38
3
1. Clean all parts and inspect for wear or damage.
Replace parts as needed.
2. If necessary, reinstall the felt dampener (29) and
side cover (31). Torque the screws (39) to 28 in-lb
(3.1 NSm).
32
H
1
3. Install new ball check seals (24).
24 4
4. Place the fluid covers (32) on the housing (1).
Align the mounting holes (H) in the fluid covers
with the holes in the housing. Install the screws
(38) loosely, then torque oppositely and evenly to
10 ft-lb (13.6 NSm).
1
H
1
24
4
39
2
31, 29
5. Reinstall the pump on its mounting.
6. Reconnect the ground wire and hoses.
H 1
32
38
ti1031a
3
Fig. 3
309303
15
Service
Reassembly
Ball Check Repair
1. Reinstall the inlet and outlet ball checks on one
side of the pump. The inlet and outlet checks are
assembled differently. Install the parts exactly as
shown in Fig. 4.
Tools Required
D O-ring pick
Disassembly
NOTE: Ball Check Repair Kit 245067 is available.
Parts included in the kit are marked with a double
dagger, for example (21}). Use all the parts in the kit
for the best results.
2. Install one cover (32) loosely, to prevent the ball
checks from falling out. See page 14.
3. Turn the pump over and install the ball checks on
the opposite side, exactly as shown.
1. Remove the fluid covers. See page 14.
2. Remove the inlet and outlet ball checks. Note that
the orientation of the inlet check parts is different
from the outlet check parts. See Fig. 4.
4. Reinstall the fluid covers. See page 14.
NOTE: If the inlet seats (26) are difficult to remove,
drive them out from the opposite side using a brass
rod and hammer.
3. Clean all parts and inspect for wear or damage.
Replace parts as needed.
1
24
}
}
10 ft-lb (13.6 NSm)
27
1
32
21
}
}
Align
2
}24
}23
26
25}
z
}21
}27
2
Inlet Ball Checks
Outlet Ball Checks
}
2
2
25}
26
}
}
}27
}21
}23
}24
21
27
}
}
24
1
ti1032a
Fig. 4
16
309303
Service
3. Thread an M8 hexnut (A) onto an M8 bolt. Screw
Diaphragm Repair
the bolt into the shaft (5) until it bottoms out.
Thread the nut down to the shaft to lock it.
Tools Required
D M8 bolt
D
M
8
h
e
x
n
u
t
4. Hold the nut with a wrench or vise to keep the
shaft from turning. Unscrew the other diaphragm
(6) by hand.
D
A
d
j
u
s
t
a
b
l
e
w
r
e
n
c
h
,
o
r
v
i
s
e
NOTE: Diaphragm Repair Kit 245065 is available.
Parts included in the kit are marked with an asterisk,
for example (6*). Always replace both diaphragms for
the best results.
NOTE: If you cannot remove the second diaphragm,
refer to Shaft Repair Disassembly on page 20.
1. Remove the fluid covers. See page 14.
Reassembly
1. Screw the new diaphragms (6*) into the shaft (5)
handtight.
WARNING
Wear gloves when removing the diaphragms to
reduce the risk of cuts.
2. Replace the ball check seals (24*) with the new
seals in the kit.
2. Unscrew one diaphragm (6) from the shaft (5) by
hand. See Fig. 5.
3. Reinstall the fluid covers. See page 14.
2
10 ft-lb (13.6 NSm)
38
32
1
1
Align
2
3
2
Use M8 bolt and nut to keep shaft from turning.
6*
2
5
24*
A 3
*24
2
1
*24
24*
*6
32
38
1
ti1033a
Fig. 5
309303
17
Service
5. Remove the retaining rings (11) and plug (9) from
Air Valve Repair
both sides, and slide the carriage (7) from the
center housing (1). Remove the o-rings (8, 10)
from the carriage and the plug.
Tools Required
D 3 mm allen wrench
D Needlenose pliers
D Retaining ring removal tool
D O-ring pick
6. Clean all parts and inspect for wear or damage.
Replace parts as needed.
Orient “POM” marking on air
valve plate as shown in
1
Disassembly
relation to fluid outlet arrow.
NOTE: Air Valve Repair Kit 245066 is available. Parts
included in the kit are marked with a dagger, for exam-
ple (8{). Use all the parts in the kit for the best results.
1
1. Remove the side cover (31) and felt dampener
(29).
“POM”
marking
2. Remove the four screws (36), air valve cover (17),
and gasket (16). See Fig. 7.
3. See Fig. 6. Note the orientation of the air valve
plate (13) relative to the fluid outlet arrow, with
“POM” marking up. Pull the plate out of the center
housing (1). Remove the three o-rings (14, 15) and
the two o–rings (43) from the plate. See Fig. 7.
fluid outlet
arrow
1
13{
ti15226a
4. Remove the air valve cup (12) from the center
housing (1).
Fig. 6
18
309303
Service
5. Lubricate the large o-ring (15{) and the two small
Air Valve Repair (continued)
o-rings (14{) and install them on the air valve plate
(13{). Align the point on the plate with the arrow
on the center housing (1) as shown in Fig. 6.
Install the plate in the housing.
Reassembly
1. Lubricate the o-rings (8{) and install them on the
carriage (7). Slide the carriage into the center
housing (1) so the notch faces out, as shown in
Fig. 7.
6. Install the gasket (16{). Note the orientation.
2. Lubricate each o-ring (10{) and install them on the
plugs (9). Insert a plug in each side to secure the
carriage (7). Install the retaining rings (11) to hold
these parts in place.
7. Reinstall the air valve cover (17) and screws (36).
Torque the screws to 28 in-lb (3.1 NSm).
8. Replace the ball check seals (24{) with the new
3. Install the air valve cup (12{) in the notch of the
seals in the kit.
carriage (7) so the open side faces out.
4. Install two o–rings (43) in the counterbore of the air
motor.
9. Reinstall the felt dampener (29) and side cover
(31). See page 14.
Lubricate
2
10{ 2
28 in-lb (3.1 NSm)
4
5
9
11
Align. See Fig. 6.
1
7
12{
{
8
14{
2
2
15{
2
13{ 5
{
8
2
16{
29
17
31
4
36
4
39
10{ 2
43
9
11
ti1044d
Fig. 7
309303
19
Service
7. If you could not remove one diaphragm from the
Shaft Repair
shaft, place the shaft in a vise with soft jaws.
Unscrew the remaining diaphragm (6) from the
shaft (5) by hand.
Tools Required
D Needlenose pliers
D O-ring pick
8. Clean all parts and inspect for wear or damage.
Replace parts as needed.
D Retaining ring removal tool
D Vise with soft jaws
Disassembly
Reassembly
NOTE: Shaft Repair Kit 24A155 is available. Parts
included in the kit are marked with a star, for example
(5l ). Use all the parts in the kit for the best results.
1. Screw one diaphragm (6) into the shaft (5l )
handtight.
NOTE: Shaft and Bearing Repair Kit is available. Parts
included in the kit are marked with a symbol, for exam-
ple (44l ). Use all the parts in the kit for the best
results.
2. Lubricate the o–rings (45, 46) and install on the
bearings (44). Install the bearings in the center
housing (1) and secure with the retaining rings
(47).
1. Remove the fluid covers. See page 14. Remove
the side cover (31) and felt dampener (29).
3. Place the valve carriage (3) in the center housing
(1). Grease the shaft (5l ) and slide it through the
center housing and valve carriage.
2. Disassemble the air valve. See page 18.
3. Remove the diaphragms (6). See page 17.
4. Install the retaining rings (4l ) on the shaft (5l ).
4. Remove the retaining rings (4l ) from the shaft (5).
See Fig. 8.
5. Screw the second diaphragm (6) into the shaft
(5l ) handtight.
5. Slide the shaft (5) out of the center housing (1).
Remove the valve carriage (3) from the housing.
6. Reassemble the air valve and carriage (see page
18), using the new o-rings (8l , 10l , 14l , 15l )
and gasket (16l ) included in the shaft repair kit.
6. Remove the retaining rings (47) and bearings (44).
Remove the o–rings (45, 46) from the bearings.
7. Replace the ball check seals (24l ) with the new
CAUTION
seals in the kit.
Do not grip the shaft with tools that can scratch or
damage the shaft, such as wrenches or pliers.
8. Reinstall the fluid covers. See page 14.
20
309303
Service
Shaft Repair (continued)
38
32
1
3
10 ft-lb (13.6 NSm).
1
Lubricate.
2
3
4
6
Align.
28 in-lb (3.1 NSm).
g
l
4
7
44g
l
Align. See Fig. 6.
5
g
l
4
6
2
45g
l
2
l
5
2
24{
l
{
l
2
4
3
1
3
l
8
2
4l
l
8
7
12{
2
l 10
9
14{
2
2
15{
2
13
5
45g
l
4
36
16{
g
l
4
6
2
17
2
11
l
2
4
29
24{
l
44g
l
31
39
g
l
4
7
43
4
6
3
32
38
1
ti1035E
Fig. 8
309303
21
Parts
Part No. 233500 Aluminum Pump, Series D, npt threads
Part No. 233501 Stainless Steel Pump, Series C, npt threads (Shown)
Part No. 233776 Aluminum Pump, Series C, BSPP threads
Part No. 233777 Stainless Steel Pump, Series C, BSPP threads
38
32
Detail of Grounding Screw
*6
24*{
}
l
30
33
40Y
27}
35
37
20
19
21
}
5
l
g
l
4
7
26
}
44g
l
25}
z
46g l
ti1030b
g
l
4
5
1
18
3
28
4l
7
12{
14
{
l
{
l
8
15
{
l
{
l
1
0
13{
45
g
l
9
16{
l
g
l
4
6
11
44g
l
17
g
l
4
7
36
}22
}27
43{
l
}21
}23
29
31
*{
}
l
2
4
6*
32
39
ti1036F
22
309303
Parts
NOTE: Purchase items 36–39 locally.
Ref.
No.
Ref.
No.
Part No. Description
Qty.
Part No. Description
Qty.
1
15J732
198894
HOUSING, center;
for Part No. 233500; aluminum
HOUSING, center;
for Part No. 233501;
stainless steel
HOUSING, center;
for Part No. 233776; aluminum
HOUSING, center;
for Part No. 233777;
stainless steel
CARRIAGE, valve
RING, retaining, shaft
SHAFT, diaphragm
DIAPHRAGM; PTFE
composite
32
197674
COVER, housing;
for Part Nos. 233500 and 233776;
aluminum
COVER, housing;
for Part Nos. 233501 and 233777;
stainless steel
FITTING, air inlet; for Part Nos.
233500 and 233501
FITTING, air inlet; for Part Nos.
233776 and 233777
SCREW, grounding; M5 x 10
SCREW, cap, socket-hd;
M4 x 20
SCREW, cap, socket-hd;
M4 x 12
SCREW, cap, socket-hd;
M8 x 18; for Part Nos.
233500 and 233776
SCREW, same as above; for
Part Nos. 233501 and 233777 12
SCREW, button-hd; M4 x 12
LABEL, warning
O–RING
1
2
197680
1
1
198892
197679
2
33
198832
198831
1
1
1
2
1
1
1
3
197645
197646
n/a
35
36
116343
116474
4l
5l
4
2
6*
7
197648
37
38
116475
117367
2
1
2
2
2
2
1
1
2
1
1
1
1
1
1
4
2
197649
197650
197651
197652
197653
197654
197655
197656
197657
197658
197659
197660
197661
197662
197663
197664
197665
CARRIAGE
O-RING, carriage
PLUG, carriage
O-RING, plug
RING, retaining, carriage
CUP, valve, air
8{
l
9
12
10
11
12
13
14
15
16
17
18
19
20
21
22
23
{
l
15D128
{
{
{
{
{
39
116595
188621
157628
n/a
n/a
n/a
2
1
2
2
2
2
2
PLATE, valve, air
O-RING, valve, air
O-RING, valve, air
GASKET, valve, air
COVER, valve, air
VALVE, safety, air
PLATE, dampener; neoprene
DAMPENER; steel
BALL; acetal
SEAL, valve, outlet; acetal
SEAT, valve, outlet;
stainless steel
SEAL, ball check; nylon
O-RING, valve, inlet;
fluoroelastomer
40
43
44
45
46
47
Y
{
l
l
l
l
l
l
l
l
BEARING
O–RING, nitrile
O–RING, nitrile
RING, retaining
n/a
*
These parts are only available by purchasing Dia-
phragm Repair Kit 245065.
}
}
}
{
T
h
e
s
e
p
a
r
t
s
a
r
e
o
n
l
y
a
v
a
i
l
a
b
l
e
b
y
p
u
r
c
h
a
s
i
n
g
A
i
r
Valve Repair Kit 245066.
2
4
24*
25
{
}
l
1
9
7
6
6
6
}
T
h
e
s
e
p
a
r
t
s
a
r
e
o
n
l
y
a
v
a
i
l
a
b
l
e
b
y
p
u
r
c
h
a
s
i
n
g
B
a
l
l
}
z
197667
Check Repair Kit 245067.
2
l
T
h
e
s
e
p
a
r
t
s
a
r
e
o
n
l
y
a
v
a
i
l
a
b
l
e
b
y
p
u
r
c
h
a
s
i
n
g
S
h
a
f
t
26
}
}
197668
SEAT, valve, inlet;
stainless steel
and Bearing Repair Kit 24A155.
2
4
1
1
1
1
27
28
29
30
31
197669
197670
197671
16A659
16A661
GUIDE, ball; acetal
DAMPENER, felt, air inlet side
DAMPENER, felt, side
COVER, air inlet side
COVER, side
Y
R
e
p
l
a
c
e
m
e
n
t
D
a
n
g
e
r
a
n
d
W
a
r
n
i
n
g
l
a
b
e
l
s
,
t
a
g
s
a
n
d
cards are available at no cost.
z
T
h
i
s
p
a
r
t
a
v
a
i
l
a
b
l
e
i
n
1
0
–
p
a
c
k
k
i
t
1
5
D
5
6
4
o
r
i
n
B
a
l
l
Check Repair kit 245067
309303
23
Technical Data
Category
Data
Maximum fluid working
pressure
115 psi (0.8 MPa, 8.0 bar)
Air pressure operating range
Ratio
12 to 115 psi (.08 to 0.8 MPa, 0.8 to 8.0 bar)
1:1
Maximum free flow delivery
8.5 gal./min (32 l/min)
Operating fluid temperature
range
50 to 176_ C (10 to 80_ C)
Maximum suction lift
Weight
16 ft (4.8 m) dry; 22 ft (6.5 m) wet
Part Nos. 233500, 233776: 9 lb (4 kg)
Part Nos. 233501, 233777: 14 lb (6.4 kg)
Wetted parts
Part Nos. 233500, 233776: Aluminum, Stainless Steel, Acetal, Nylon, PTFE,
fluoroelastomer
Part Nos. 233501, 233777: Stainless Steel, Acetal, Nylon, PTFE, fluoroelastomer
Sound Pressure Levels in dB(A)*
(measured at 1 m from unit)
Sound Power Levels in dB(A)*
(tested in accordance with ISO 3744)
Input Air Pressures
40 psi (0.28 MPa, 2.8 bar)
60 psi (0.42 MPa, 4.2 bar)
Sound Pressure
Input Air Pressures
40 psi (0.28 MPa, 2.8 bar)
60 psi (0.42 MPa, 4.2 bar)
Sound Power
69.1
72.1
80.8
83.7
Performance Chart
To find Fluid Outlet Pressure (psi/MPa/bar) at a specific fluid flow
(lpm/gpm) and operating air pressure (psi/MPa/bar):
To find Pump Air Consumption (l/min or scfm) at a specific fluid flow
(lpm/gpm) and air pressure (psi/MPa/bar):
1. Locate desired flow along bottom of chart.
1. Locate desired flow along bottom of chart.
2. Follow vertical line up to intersection with selected fluid outlet
pressure curve (black). Follow left to scale to read fluid outlet
pressure.
2. Read vertical line up to intersection with selected air consumption
curve (dashes). Follow left to scale to read air consumption.
A
B
C
D
115 psi (0.8 MPa, 8 bar) air pressure
90 psi (0.6 MPa, 6 bar) air pressure
60 psi (0.4 MPa, 4 bar) air pressure
30 psi (0.2 MPa, 2 bar) air pressure
Test Fluid: No. 10 Weight Oil
Fluid Outlet Pressure
Air Consumption
psi
scfm
cycles per minute
cycles per minute
47 71 94 118 141 165 188
MPa, bar
l/min
24
47 71
94 118 141 165 188
24
8
7
6
5
4
3
2
1
0
120
224
196
168
140
112
84
A
B
0.8, 8.0
A
B
C
100
0.7, 7.0
80
0.6, 6.0
60
C
D
0.4, 4.0
40
0.3, 3.0
20
56
D
28
0.14, 1.4
0
0
1
2
3
4
5
6
7
8
0
1
2
3
4
5
6
7
8
gpm
l/min
gpm
l/min
3.8 7.6 11.4 15.2 19.0 22.8 26.6 30.4
3.8 7.6 11.4 15.2 19.0 22.8 26.6 30.4
24
309303
Dimensions
BOTTOM VIEW
4.53 in.
(115 mm)
3/8 npt or 3/8 BSPP Fluid Outlet
Two 0.35 in. (9 mm) diameter
holes, for mounting pump
1/4 npt or 1/4 BSPP Air Inlet
3/4 npt or M26 x 1.5
Fluid Inlet
4.1 in.
(104 mm)
SIDE VIEW
Aluminum
SIDE VIEW
SST
4.88 in.
(124 mm)
9.1 in.
(231.5 mm)
8.2 in.
(208 mm)
ti1037a
TI3265A
309303
25
Graco Standard Warranty
Graco warrants all equipment manufactured by Graco and bearing its name to be free from defects in material and workmanship on the
date of sale to the original purchaser for use. With the exception of any special, extended, or limited warranty published by Graco,
Graco will, for a period of twelve months from the date of sale, repair or replace any part of the equipment determined by Graco to be
defective. This warranty applies only when the equipment is installed, operated and maintained in accordance with Graco’s written
recommendations.
This warranty does not cover, and Graco shall not be liable for general wear and tear, or any malfunction, damage or wear caused by
faulty installation, misapplication, abrasion, corrosion, inadequate or improper maintenance, negligence, accident, tampering, or sub-
stitution of non–Graco component parts. Nor shall Graco be liable for malfunction, damage or wear caused by the incompatibility of
Graco equipment with structures, accessories, equipment or materials not supplied by Graco, or the improper design, manufacture,
installation, operation or maintenance of structures, accessories, equipment or materials not supplied by Graco.
This warranty is conditioned upon the prepaid return of the equipment claimed to be defective to an authorized Graco distributor for
verification of the claimed defect. If the claimed defect is verified, Graco will repair or replace free of charge any defective parts. The
equipment will be returned to the original purchaser transportation prepaid. If inspection of the equipment does not disclose any defect
in material or workmanship, repairs will be made at a reasonable charge, which charges may include the costs of parts, labor, and
transportation.
THIS WARRANTY IS EXCLUSIVE, AND IS IN LIEU OF ANY OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING BUT
NOT LIMITED TO WARRANTY OF MERCHANTABILITY OR WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE.
Graco’s sole obligation and buyer’s sole remedy for any breach of warranty shall be as set forth above. The buyer agrees that no other
remedy (including, but not limited to, incidental or consequential damages for lost profits, lost sales, injury to person or property, or any
other incidental or consequential loss) shall be available. Any action for breach of warranty must be brought within two (2) years of the
date of sale.
Graco makes no warranty, and disclaims all implied warranties of merchantability and fitness for a particular purpose in connection
with accessories, equipment, materials or components sold but not manufactured by Graco. These items sold, but not manufactured
by Graco (such as electric motors, switches, hose, etc.), are subject to the warranty, if any, of their manufacturer. Graco will provide
purchaser with reasonable assistance in making any claim for breach of these warranties.
In no event will Graco be liable for indirect, incidental, special or consequential damages resulting from Graco supplying equipment
hereunder, or the furnishing, performance, or use of any products or other goods sold hereto, whether due to a breach of contract,
breach of warranty, the negligence of Graco, or otherwise.
FOR GRACO CANADA CUSTOMERS
The parties acknowledge that they have required that the present document, as well as all documents, notices and legal proceedings
entered into, given or instituted pursuant hereto or relating directly or indirectly hereto, be drawn up in English. Les parties reconnais-
sent avoir convenu que la rédaction du présente document sera en Anglais, ainsi que tous documents, avis et procédures judiciaires
exécutés, donnés ou intentés à la suite de ou en rapport, directement ou indirectement, avec les procedures concernées.
Graco Information
TO PLACE AN ORDER, contact your Graco distributor, or call one of these numbers
to identify the distributor closest to you:
1–800–328–0211 Toll Free
612–623–6921
612–378–3505 Fax
All written and visual data contained in this document reflects the latest product information available at the time of publication.
Graco reserves the right to make changes at any time without notice.
Original instructions. This manual contains English. MM 309303
Graco Headquarters: Minneapolis
International Offices: Belgium, China, Japan, Korea
GRACO INC. P.O. BOX 1441 MINNEAPOLIS, MN 55440–1441
Copyright 2001, Graco Inc. is registered to ISO 9001
Revised 02/2011
26
309303
|