Mobile Lubrication Library
Telehandler Loadall
Suggested automated lubrication system layout for Telehandler
Loadall
Kit No.: 24R378, G3, USP, 21PT
Maximum System Working Pressure: 3000 psi (206 bar, 20.7 MPa)
Important Safety Information
Read all warnings and instructions in all
Fluid leaks from incorrectly installed or ruptured compo-
related manuals. Save all instructions.
nents, and/or failure to verify the components are prop-
erly installed and tested, can result in serious injury such
as fluid spraying in the eyes or on skin and fluid injection,
Related Manuals
Manual No. Manual Title
or equipment damage.
To prevent injury or equipment damage, installation must
be done by a professional and tested prior to use. Con-
sult Parker literature for specific hose assembly instruc-
tions. These instructions are available from your Parker
3A0414
3A0525
3A0528
3A0860
G3 Pump
Pressure Relief Valve
Remote Manual Run
USP Valves
The information contained in this document is only a recommendation for an automatic lubrication system and is not intended to
replace the installation and maintenance instructions provided by the original equipment manufacturer.
Mobile Lubrication Library
LUBE POINT INFORMATION
USP Volume
Dispense
Single
Single
Single
Single
Single
Single
Single
Single
Single
Single
Single
Single
Double
Single
Single
Single
Single
Single
Single
Single
Single
Lube Point USP Outlet
Bearing Description
USP Block
1
2
5
6
1
2
3
4
5
6
7
8
1
2
King pin upper right
King pin lower right
King pin upper left
SB#2
SB#2
SB#2
SB#2
SB#2
SB#2
SB#3
SB#3
SB#3
SB#3
SB#3
SB#3
SB#3
SB#4
SB#4
SB#4
SB#4
SB#4
SB#4
SB#4
SB#4
3
4
King pin lower left
5
Steering arm left
6
Steering arm right
7
Boom pivot left
8
Telescope ram rear
Upper compensating ram
Main lift boom cylinder upper
Boom pivot right
9
10
11
12
13
14
15
16
17
18
19
20
21
Main lift boom cylinder lower
3 and 4 Lower compressing ram
5
6
7
8
1
2
King pin upper right
King pin lower right
Steering arm right
Trunion right
King pin upper left
King pin lower left
Steering arm left
Trunion left
3
4
Mobile Lubrication Library
24R378: Recommended Kit Parts List
Part
Number
Qty
Description
1
1
96G099
571036
571028
24E406
24E407
571032
24N007
16U586
556773
556763
555749
557393
556402
557349
16U587
15K783
127009
16U982
16U933
24F467
557944
127012
563178
127013
PUMP, G3-G-12MX-4L0L00-UDMVA1R2 (see manual 3A0414)
KIT, accessory, cover
1
KIT, accessory, pressure relief (see manual 3A0525)
KIT, valve, USP, 6 outlet (see manual 3A0860)
KIT, valve, USP, 8 outlet (see manual 3A0860)
KIT, remote manual run, 12V, w/ cable (see manual 3A0528)
KIT, accessory, mounting, USP, 6-8
KIT, accessory, hose, 100 ft
2
2
1
4
1
8
HOSE, end female swivel SAE 4 JIC
FITTING, 4 JIC 1/8 pm
25
30
21
1
CONNECTOR, 4 JIC 1/8 pm
COUPLING, 1/8 fp x 1/8 mp x 1-1/4 HEX
FITTING, 1/4 x 1/8 nptf hex
4
PLUG, dryseal 1/8 nptf
1
KIT, accessory, guard, scuff, 75 ft
FITTING, elbow, street, 1/8
5
4
TIE, cable, 14.75’ x .31” black
1
KIT, accessory, hose, 200 ft
1
KIT, accessory, guard, scuff, 160 ft
PLUG, USP, doubling plug
4
20
20
4
CLAMP, 7/16, tube 4TS6-14002
CLAMP, hose, .375 OD hose
COUPLING, extension 1/8 female to 1/8 male
FITTING, swivel, JIC 37D size #4
42
USP VALVES* AND ACCESSORIES
Part Number
Description
24E408
KIT, valve, USP, 10 outlet
24E409
KIT, valve, USP, 12 outlet
24E410
KIT, valve, USP, 14 outlet
24E411
KIT, valve, USP, 16 outlet
24N008
KIT, mounting bracket, 10-12 outlets
KIT, mounting bracket, 14-16 outlets
24N009
*see manual 3A0860
Mobile Lubrication Library
Typical Pump Installation
Manual Run
Button
Pressure Relief
To Fuse/Power
To Lube Points
G3
Pump
USP
Valve
Mobile Lubrication Library
Graco Information
TO PLACE AN ORDER, contact your Graco distributor or call to identify the nearest distributor.
Phone: 612-623-6928 or Toll Free: 1-800-533-9655, Fax: 612-378-3590
All written and visual data contained in this document reflects the latest product information available at the time of publication.
Graco reserves the right to make changes at any time without notice.
Original information. This manual contains English. MM 333504
Graco Headquarters: Minneapolis
International Offices: Belgium, China, Japan, Korea
GRACO INC. AND SUBSIDIARIES • P.O. BOX 1441 • MINNEAPOLIS MN 55440-1441 • USA
Copyright 2013, Graco Inc. All Graco manufacturing locations are registered to ISO 9001.
August 2013, revised January 2014
|