Graco Water Dispenser Model 214623 User Manual

Instructions–Parts List  
HIGH PRESSURE  
Surge Tanks and  
307296T  
Fluid Filters  
EN  
For fluid surge reduction and for filtering of finishing materials.  
Important Safety Instructions  
Read all warnings and instructions in this manual.  
Save these instructions.  
Fluid Filters  
5000 psi (350 bar, 35 MPa) Maximum Working Pressure  
Model 238620, Series A  
Fluid Filter,  
Fluid Filter,  
Cover  
Exposed Mounting  
Exposed  
Mounting  
Mounting  
Model 214724, Series E  
Cover Mounting  
1008  
1009  
Model 289310, Series A  
Cover Mounting  
Fluid Filter  
7252 psi (500 bar, 50 MPa) Maximum Working Pressure  
Model 237069, Series A  
Exposed Mounting  
Surge Tanks (with filter)  
5000 psi (350 bar, 35 MPa) Maximum Working Pressure  
Model 214624, Series C  
Exposed Mounting  
Model 238623, Series A  
Exposed Mounting  
Model 214726, Series E  
Cover Mounting  
Mastic Surge Tanks (without filter)  
5000 psi (350 bar, 35 MPa) Maximum Working Pressure  
Surge Tank,  
Exposed  
Mounting  
Surge Tank,  
Cover  
Mounting  
Model 214623, Series A  
Exposed Mounting; for use with high viscosity fluids  
Model 214725, Series C  
Covered Mounting; for use with low to medium viscosity fluids  
1008  
1005  
 
Installation  
The top of the surge tank must always be supported.  
Typical Mountings  
See Accessories on page 13 for mounting clamps.  
See Fig. 1 for typical mountings. See page 14 for the  
mounting hole layout.  
Surge tanks must always be mounted upright, as  
shown in Fig. 1, not horizontally.  
Install the surge tank or filter near the pump outlet.  
Position the surge tank so the labels face away from  
the pump and so the setscrews, near the top and  
bottom of the tank, face toward the pump.  
Exposed Mountings  
Detail A: With Riser Tube  
Detail B: No Riser Tube  
05910  
Drum Cover Mountings  
Detail D: Separate Riser Tube  
Detail C: Integral Riser Tube  
05912  
Fig. 1  
307296  
3
 
Surge Tank Conversion Kits  
Connect the surge tank to the fluid outlet (F) of the  
displacement pump and install the clamp in the option-  
al outlet (E) at the base of the air motor. See Fig. 2.  
Surge Tank Conversion Kits 238634 and  
237704  
Use Conversion Kits 238634 or 237704 to add a surge  
tank to a pump. Kit 238634 includes surge tank  
238623 (A) and clamp 238630 (B). Kit 237704 includes  
surge tank 214624 (A), clamp 238630 (B), and attach-  
ing hardware (C).  
1
2
These parts are included with Conversion Kit 237704 only.  
Model 238623 Surge Tank shown.  
E
B
C
1
A
2
F
05927  
Fig. 2  
4
307296  
 
Operation  
Before operating the equipment, be sure the drain  
valve is closed.  
Be sure the drain valve is fully closed when spraying  
and fully open when draining or circulating fluid to get  
the best results and reduce wear on the valve.  
Flush the equipment with a compatible solvent to  
remove oil used for factory testing and rust prevention.  
If you notice excessive surging at the spray gun, shut  
off the pump, trigger the gun to relieve fluid pressure,  
and open the drain valve (D) at the bottom of the surge  
tank. See Fig. 3. After the tank is drained, close the  
drain valve and resume operation.  
1
Open drain valve to relieve pressure.  
1
D
1
D
05911  
05913  
Fig. 3  
307296  
5
 
Service  
Pressure Relief Procedure  
Service Notes  
Clean all parts thoroughly when disassembling. Check  
parts carefully for damage or wear, replace as needed.  
WARNING  
SKIN INJECTION HAZARD  
Numbers in parentheses in the text refer to the parts  
drawings.  
The system pressure must be manually  
relieved to prevent the system from  
starting or spraying accidentally. Fluid  
Check periodically for leakage from the small holes  
near the top and bottom of the surge tanks. If you find  
leakage at the holes or anywhere else, replace the  
seals promptly.  
under high pressure can be injected through the  
skin and cause serious injury. To reduce the risk of  
an injury from injection, splashing fluid, or moving  
parts, follow the Pressure Relief Procedure  
whenever you:  
Before removing the end plug and adapter from the  
surge tank, loosen the setscrews (5) near the bottom  
of the tank (6). See the parts drawings on pages 7  
through 12.  
D are instructed to relieve the pressure,  
D stop spraying,  
D check or service any of the system equipment,  
D or install or clean the spray tips.  
Inspect the sealing surfaces for nicks or scratches that  
might cause leakage. Do not damage the sealing  
surfaces.  
1. Lock the gun trigger safety.  
When reassembling filters after cleaning or servicing,  
be sure to install the filter support as shown in the  
parts drawings. Do not install it upside down.  
2. Turn off the power to the pump.  
3. Close any master bleed-type air valves.  
4. Unlock the gun trigger safety.  
WARNING  
Tighten all threaded connections securely. High  
pressure fluid can dislodge a loose connection or  
allow high pressure fluid to be emitted from the  
connection and cause serious injury.  
5. Hold a metal part of the gun firmly to the side of a  
grounded metal pail, and trigger the gun to relieve  
pressure.  
6. Lock the gun trigger safety.  
7. Place a pail under the drain valve, and open the  
drain valve to be sure all fluid pressure is relieved.  
Keep hands away from the end of the drain valve  
when opening it.  
8. Leave the drain valve open until you are ready to  
spray again.  
If you suspect that the spray tip or hose is completely  
clogged, or that pressure has not been fully relieved  
after following the steps above, very slowly loosen the  
tip guard retaining nut or hose end coupling and relieve  
pressure gradually, then loosen completely. Now clear  
the tip or hose.  
6
307296  
 
Parts  
Model 214724, Series E  
See Accessories for other available screens.  
Replace filter support if ridges are worn down.  
1
2
1
Model 289310, Series A  
Includes items 1–25  
2
3
4
Lubricate.  
Do not damage PTFE o-ring (7). Lubricate and  
bend into kidney shape, then push into groove.  
3
4
1
5
6
24  
23  
10  
2
14  
12  
11  
25  
7
4
3
18  
15  
19  
20  
21  
12  
16  
13  
17  
22  
1007  
Ref  
No.  
Ref  
No.  
Part No.  
Description  
Qty  
Part No.  
Description  
Qty  
1
2
3n  
4
5
174058  
104813  
174056  
171941  
167025  
167024  
186075  
104804  
104839  
102291  
164900  
175043  
103337  
RING, lock  
PLUG, pipe, 3/8 npt  
BOWL, filter  
SPRING, conical compression  
STRAINER, 60 mesh (Model 214724) 1  
STRAINER, 30 mesh (Model 289310) 1  
1
1
1
1
15  
16  
17  
18  
19  
20  
21  
22  
23  
24  
25  
166697  
165964  
102310  
172094  
165273  
206481  
103648  
165274  
104663  
174080  
101754  
STEM, valve  
NUT, packing  
NUT, acorn, no. 10–32  
SEAT, ball  
BALL, valve  
SEAT, valve  
PACKING, o-ring, fluoroelastomer  
NIPPLE, adapter  
PLUG, pipe, 3/4 npt  
MANIFOLD  
1
1
1
1
1
1
1
1
1
1
1
6
SUPPORT, filter  
1
1
1
2
2
1
1
7n  
10  
11  
12  
13  
14  
PACKING, o-ring, PTFE  
PLUG, pipe, 1/2 npt  
PIN, drive  
WASHER, flat  
LEVER  
PLUG, pipe, 3/8 npt  
n Keep these spare parts on hand to reduce down time.  
PACKING, o-ring, fluoroelastomer  
307296  
7
 
Parts  
Model 238620, Series A  
1
2
Includes items 1–28  
8
2
10  
2
See Accessories for other available screens.  
Replace filter support if ridges are worn down.  
1
2
3
3
4
Lubricate.  
Do not damage PTFE o-ring (7). Lubricate and  
bend into kidney shape, then push into groove.  
26  
4
5
9
1
27  
2
6
7
28  
4
3
05908  
Ref  
No.  
Ref  
No.  
Part No.  
Description  
Qty  
Part No.  
Description  
Qty  
1
2
3n  
4
5
6
7n  
8
174058  
104813  
174056  
171941  
167025  
186075  
104804  
24C497  
RING, lock  
PLUG, pipe, 3/8 npt  
BOWL, filter  
SPRING, conical compression  
STRAINER, 60 mesh  
SUPPORT, filter  
PACKING, o-ring, PTFE  
MANIFOLD, paint filter  
1
3
1
1
1
1
1
1
9
223960  
104839  
155665  
205448  
186447  
BALL VALVE, see 306861 for parts  
PLUG, pipe, 1/2 npt  
UNION, adapter  
COUPLING, swivel; 3/8 npsm(f)  
TUBE, drain; nylon;  
1/4 in. (0.6 mm) ID; 5 in. (127 mm)  
1
1
1
1
10  
26  
27  
28  
1
n Keep these spare parts on hand to reduce down time.  
8
307296  
 
Parts  
Model 237069  
1
2
Includes items 1–26  
See Accessories for other available screens.  
Replace filter support if ridges are worn down.  
1
2
3
4
Lubricate.  
Do not damage PTFE o-ring (7). Lubricate and  
bend into kidney shape, then push into groove.  
3
4
5 1  
8
10  
2
2
6 2  
26  
9
7
4
3
05909  
Ref  
No.  
Ref  
No.  
Part No.  
Description  
Qty  
Part No.  
Description  
Qty  
1
2
3n  
4
5
174058  
104813  
174056  
171941  
167025  
186075  
104804  
RING, lock  
PLUG, pipe, 3/8 npt  
BOWL, filter  
SPRING, conical compression  
STRAINER, 60 mesh  
SUPPORT, filter  
1
3
1
1
1
1
1
8
9
10  
26  
24C497  
224774  
100737  
156296  
MANIFOLD, paint filter  
DRAIN VALVE  
PLUG, pipe, 1/2 npt  
NIPPLE; 3/8 npt x 1/8 npt  
1
1
1
1
6
7n  
PACKING, o-ring, PTFE  
n Keep these spare parts on hand to reduce down time.  
307296  
9
 
Parts  
See Accessories for other  
available screens.  
Model 214624, Series C  
Includes items 1–16, 31, 33, 34  
1
5
1
Replace filter support if  
ridges are worn down.  
3
3
2
3
2
3
Model 214726, Series E  
Includes items 1–13, 17–32, 34  
Lubricate.  
Do not damage PTFE o-ring (13).  
Lubricate and bend into kidney  
shape, then push into groove.  
4
5
6
6
Torque to 150 ft–lb (200 N.m).  
Torque to 40 in–lb (4.5 N.m).  
5
6
11  
11  
34  
3
3
3
3
2
3
3
2
6
5
7
12 5  
8
9
12  
5
4
13  
3
4
1
13  
15  
14  
3
31  
30  
23  
31  
19  
15  
17  
18  
32  
33  
16  
24  
25  
26  
27  
28  
10  
2
20  
17  
21  
29  
22  
1004  
Ref  
No.  
Ref  
No.  
Part No.  
Description  
Qty  
Part No.  
Description  
Qty  
1
174064  
104805  
166612  
111463  
none  
PLUG, end  
RING, backup, PTFE  
PACKING, o-ring, PTFE  
SETSCREW,1/4–20 x 3/8”  
TANK, accumulator not sold separately 1  
ADAPTER, filter  
SPRING, conical compression  
STRAINER, 60 mesh  
SUPPORT, filter  
1
2
2
2
21  
22  
23  
24  
25  
26  
27  
28  
29  
30  
31  
32  
33  
165964  
102310  
174080  
101754  
172094  
165273  
206481  
103648  
165274  
104663  
104839  
102291  
155665  
169579  
NUT, packing  
NUT, acorn, No. 10–32  
MANIFOLD  
PLUG, pipe, 3/8 npt  
SEAT, ball  
BALL, valve  
SEAT, valve  
PACKING, o-ring, fluoroelastomer  
NIPPLE, adapter  
PLUG, pipe, 3/4 npt  
PLUG, 1/2 npt  
1
1
1
1
1
1
1
1
1
1
1
2
1
1
2n  
3n  
5
6
7
174059  
171941  
167025  
186075  
174058  
174068  
104804  
24C497  
104813  
210658  
164900  
175043  
103337  
166697  
1
1
1
1
1
1
1
1
2
1
2
1
1
1
8
9
10  
11  
12n  
13n  
14  
15  
16  
17  
18  
RING, lock  
ADAPTER, accumulator  
PACKING, o-ring, PTFE  
MANIFOLD, paint filter  
PLUG, pipe, 3/8 npt  
BALL VALVE, see 306861 for parts  
WASHER, flat  
PIN, drive  
UNION, adapter  
LABEL, warning  
34Y  
n Keep these spare parts on hand to reduce down time.  
LEVER  
19  
20  
PACKING, o-ring, fluoroelastomer  
STEM, valve  
Y Replacement Danger and Warning labels, tags and cards  
are available at no cost.  
10 307296  
 
Parts  
Model 238623, Series A  
1
5
Includes items 1–36  
3
3
2
3
11  
See Accessories for other  
available screens.  
1
Replace filter support if  
ridges are worn down.  
2
3
5
6
3
2
3
3
6
Lubricate.  
Do not damage PTFE o-ring (13).  
Lubricate and bend into kidney  
shape, then push into groove.  
4
Torque to 150 ft–lb (200 N.m).  
Torque to 40 in–lb (4.5 N.m).  
5
6
5
12  
13  
4
3
34  
15  
14  
31  
15  
6
1
5
7
8
9
33  
16  
35  
36  
10  
2
05907  
Ref  
No.  
Ref  
No.  
Part No.  
Description  
Qty  
Part No.  
Description  
Qty  
1
174064  
104805  
166612  
111463  
none  
174059  
171941  
167025  
186075  
174058  
174068  
104804  
24C497  
PLUG, end  
RING, backup, PTFE  
PACKING, o-ring, PTFE  
SETSCREW,1/4–20 x 3/8”  
TANK, accumulator not sold separately 1  
ADAPTER, filter  
SPRING, conical compression  
STRAINER, 60 mesh  
SUPPORT, filter  
1
2
2
2
15  
16  
31  
33  
34Y  
35  
36  
104813  
238612  
104839  
155665  
169579  
205448  
186447  
PLUG, pipe, 3/8 npt  
BALL VALVE, see 306861 for parts  
PLUG, 1/2 npt  
UNION, adapter  
LABEL, warning  
COUPLING, swivel; 3/8 npsm(f)  
TUBE, drain; nylon;  
1/4 in. (0.6 mm) ID; 5 in. (127 mm)  
2
1
1
1
1
1
2n  
3n  
5
6
7
1
1
1
1
1
1
1
1
8
9
1
10  
11  
12n  
13n  
14  
RING, lock  
n Keep these spare parts on hand to reduce down time.  
ADAPTER, accumulator  
PACKING, o-ring, PTFE  
MANIFOLD, paint filter  
Y Replacement Danger and Warning labels, tags and cards  
are available at no cost.  
307296 11  
 
Parts  
Model 214623, Series A  
5
3
4
1
Lubricate.  
Includes items 1–12, 29  
Do not damage PTFE o-ring (9).  
Lubricate and bend into kidney  
shape, then push into groove.  
Model 214725, Series C  
Includes items 1–9, 11, 13–29  
2
3
3
3
Torque to 150 ft–lb (200 N.m).  
Torque to 40 in–lb (4.5 N.m).  
5
6
5
6
6
29  
6
5
7
3
3
3
2
14  
19  
11  
10  
12  
15  
5
27  
28  
8
20  
21  
11  
16  
22  
23  
24  
28  
17  
13  
9
3
4
18  
25  
1006  
Ref  
Ref  
No.  
Part No.  
Description  
Qty  
No.  
Part No.  
Description  
Qty  
1
174064  
104805  
166612  
111463  
none  
174058  
174068  
104804  
174060  
104663  
210658  
175043  
104839  
103337  
166697  
165964  
PLUG, end  
RING, backup, PTFE  
PACKING, o-ring, PTFE  
SETSCREW, 1/4–20 x 3/8”  
TANK, accumulator not sold separately 1  
RING, lock  
ADAPTER, accumulator  
PACKING, o-ring, PTFE  
MANIFOLD, accumulator  
PLUG, pipe, 3/4 npt  
BALL VALVE, see 306861 for parts  
LEVER  
PLUG, 1/2 npt  
PACKING, o-ring, fluoroelastomer  
STEM, valve  
1
2
2
2
18  
19  
20  
21  
22  
23  
24  
25  
27  
28  
29Y  
102310  
174080  
101754  
172094  
165273  
206481  
103648  
165274  
102291  
164900  
169579  
NUT, acorn, No. 10–32  
MANIFOLD  
PLUG, pipe, 3/8 npt  
SEAT, ball  
BALL, valve  
SEAT, valve  
PACKING, o-ring, fluoroelastomer  
NIPPLE, adapter  
PIN, drive  
WASHER, flat  
LABEL, warning  
1
1
1
1
1
1
1
1
2
2
1
2n  
3n  
5
6
7
1
1
1
1
1
1
1
1
1
1
1
8
9n  
10  
11  
12  
13  
14  
15  
16  
17  
n Keep these spare parts on hand to reduce down time.  
Y Replacement Danger and Warning labels, tags and cards  
NUT, packing  
are available at no cost.  
12 307296  
 
Accessories  
Use Only Genuine Graco Parts and Accessories  
SURGE TANK CLAMPS  
PTFE SEALS  
238630  
For ball valves and drain valves.  
For surge tanks mounted in the fluid outlet of the  
displacement pump. Install the clamp in the optional  
outlet at the base of the air motor. Requires 100902  
screw, 100016 lockwasher and 100015 nut.  
104892  
104893  
to replace 103648 fluoroelastomer seal  
to replace 103337 fluoroelastomer seal  
STAINLESS STEEL SCREENS  
167024  
167025  
167026  
167027  
595 micron (30 mesh)  
250 micron (60 mesh)  
149 micron (100 mesh)  
75 micron (200 mesh)  
100902  
100015  
100016  
172865  
For surge tanks mounted in the optional fluid outlet of  
Bulldog or King pumps when used with a riser tube.  
Attach the clamp to the top of the air motor shield.  
Requires 100902 screw, 100016 lockwasher, 100015  
nut, and two 100270 screws.  
100270  
172865  
100902  
100016  
100015  
307296 13  
 
Technical Data  
Mounting Hole  
Layout  
For mounting square base surge tanks and filters on a  
drum cover or other support.  
Category  
Data  
Maximum  
Working  
Pressure  
Model 237069: 7252 psi (500 bar, 50  
MPa)  
All Other Models: 5000 psi (350 bar,  
35 MPa)  
Weight  
Model 214623: 30 lb (13 kg)  
Model 214624: 31.5 lb (14 kg)  
Model 214724: 13 lb (6 kg)  
Model 214725: 34 lb (15 kg)  
Model 214726: 34 lb (15 kg)  
Model 237069: 10.5 lb (4.5 kg)  
Model 238620: 10.5 lb (4.5 kg)  
Model 238623: 31.5 lb (14 kg)  
Model 289310: 13 lb (6 kg)  
2.38”  
(60 mm) dia.  
1.06”  
(27 mm)  
Surge Tank  
Volume  
15 oz. (450 ml)  
2
2)  
Filter Area  
18 in (120 cm  
Wetted Parts Stainless steel, zinc-plated steel,  
nylon, PTFE, fluoroelastomer  
0.312”  
(8.12 mm) dia.  
1.06” (27 mm)  
14 307296  
 
Dimensions  
* For models 238620 and 238623, add approximately 6 in. (152 mm) to  
the “A” dimension to account for the drain tube and fitting.  
A*  
C
C
B
B
A*  
D
J
K
D
K
F
H
F
J
E
E
L
L
1005  
G
1008  
Filters  
Paint Surge Tanks  
Mastic Surge Tanks  
214724 &  
289310  
214624 &  
238623  
Dimensions  
238620  
237069  
214726  
214623  
214725  
A
11.63 in.  
(295 mm)  
11.50 in.  
(292 mm)  
10.38 in.  
(265 mm)  
23.00 in.  
(585 mm)  
21.75 in.  
(550 mm)  
22.75 in.  
(578 mm)  
21.75 in.  
(550 mm)  
(see * note  
above)  
B
C
D
E
8.75 in.  
(222 mm)  
8.75 in.  
(222 mm)  
9.62 in.  
(245 mm)  
20.12 in.  
(510 mm)  
21.00 in.  
(535 mm)  
19.88 in.  
(510 mm)  
21.00 in.  
(535 mm)  
2.06 in.  
(52 mm) dia.  
2.06 in.  
(52 mm) dia.  
2.06 in.  
3.00 in.  
3.00 in.  
3.00 in.  
3.00 in.  
(52 mm) dia. (76 mm) dia. (76 mm) dia. (76 mm) dia. (76 mm) dia.  
3.12 in.  
(79 mm) dia.  
3.12 in.  
(79 mm) dia.  
3.12 in. 3.12 in. 3.12 in. 3.12 in. 3.12 in.  
(79 mm) dia. (79 mm) dia. (79 mm) dia. (79 mm) dia. (79 mm) dia.  
3.00 in. 3.00 in. 3.00 in. 3.00 in. 3.00 in.  
3.00 in.  
(76 mm) dia.  
3.00 in.  
(76 mm) dia.  
(76 mm) dia. (76 mm) dia. (76 mm) dia. (76 mm) dia. (76 mm) dia.  
Inlets  
F
3/4 npt(f)  
3/4 npt(f)  
3/4 npt(f)  
3/8 npt(f)  
3/4 npt(f)  
3/4 npt(f)  
3/8 npt(f)  
3/4 npt(f)  
3/4 npt(f)  
3/8 npt(f)  
G
Outlets  
H
3/8 npt(f)  
1/2 npt(f)  
3/8 npt(f)  
3/8 npt(f)  
1/2 npt(f)  
3/8 npt(f)  
3/8 npt(f)  
1/2 npt(f)  
3/8 npt(f)  
3/4 npt(f)  
3/4 npt(f)  
J
K
1/2 npt(f)  
3/4 npt(f)  
1/2 npt(f)  
3/4 npt(f)  
1/2 npt(f)  
3/4 npt(f)  
Drain  
L
3/8 npt(m)  
1/8 npt(f)  
1/4 npt(m)  
3/8 npt(f)  
1/4 npt(m)  
3/8 npt(f)  
1/4 npt(m)  
Mtg. Holes  
M(2)  
1/4–20  
1/4–20  
1/4–20  
307296 15  
 
The Graco Standard Warranty  
Graco warrants all equipment manufactured by Graco and bearing its name to be free from defects in material and workmanship on the  
date of sale to the original purchaser for use. With the exception of any special, extended, or limited warranty published by Graco,  
Graco will, for a period of twelve months from the date of sale, repair or replace any part of the equipment determined by Graco to be  
defective. This warranty applies only when the equipment is installed, operated and maintained in accordance with Graco’s written  
recommendations.  
This warranty does not cover, and Graco shall not be liable for general wear and tear, or any malfunction, damage or wear caused by  
faulty installation, misapplication, abrasion, corrosion, inadequate or improper maintenance, negligence, accident, tampering, or sub-  
stitution of non–Graco component parts. Nor shall Graco be liable for malfunction, damage or wear caused by the incompatibility of  
Graco equipment with structures, accessories, equipment or materials not supplied by Graco, or the improper design, manufacture,  
installation, operation or maintenance of structures, accessories, equipment or materials not supplied by Graco.  
This warranty is conditioned upon the prepaid return of the equipment claimed to be defective to an authorized Graco distributor for  
verification of the claimed defect. If the claimed defect is verified, Graco will repair or replace free of charge any defective parts. The  
equipment will be returned to the original purchaser transportation prepaid. If inspection of the equipment does not disclose any defect  
in material or workmanship, repairs will be made at a reasonable charge, which charges may include the costs of parts, labor, and  
transportation.  
THIS WARRANTY IS EXCLUSIVE, AND IS IN LIEU OF ANY OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING BUT  
NOT LIMITED TO WARRANTY OF MERCHANTABILITY OR WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE.  
Graco’s sole obligation and buyer’s sole remedy for any breach of warranty shall be as set forth above. The buyer agrees that no other  
remedy (including, but not limited to, incidental or consequential damages for lost profits, lost sales, injury to person or property, or any  
other incidental or consequential loss) shall be available. Any action for breach of warranty must be brought within two (2) years of the  
date of sale.  
Graco makes no warranty, and disclaims all implied warranties of merchantability and fitness for a particular purpose in connection  
with accessories, equipment, materials or components sold but not manufactured by Graco. These items sold, but not manufactured  
by Graco (such as electric motors, switches, hose, etc.), are subject to the warranty, if any, of their manufacturer. Graco will provide  
purchaser with reasonable assistance in making any claim for breach of these warranties.  
In no event will Graco be liable for indirect, incidental, special or consequential damages resulting from Graco supplying equipment  
hereunder, or the furnishing, performance, or use of any products or other goods sold hereto, whether due to a breach of contract,  
breach of warranty, the negligence of Graco, or otherwise.  
FOR GRACO CANADA CUSTOMERS  
The parties acknowledge that they have required that the present document, as well as all documents, notices and legal proceedings  
entered into, given or instituted pursuant hereto or relating directly or indirectly hereto, be drawn up in English. Les parties reconnais-  
sent avoir convenu que la rédaction du présente document sera en Anglais, ainsi que tous documents, avis et procédures judiciaires  
exécutés, donnés ou intentés à la suite de ou en rapport, directement ou indirectement, avec les procedures concernées.  
Graco Information  
TO PLACE AN ORDER, contact your Graco distributor, or call one of the following numbers  
to identify the distributor closest to you:  
1–800–328–0211 Toll Free  
612–623–6921  
612–378–3505 Fax  
All written and visual data contained in this document reflects the latest product information available at the time of publication.  
Graco reserves the right to make changes at any time without notice.  
Original instructions. This manual contains English. MM 307296  
Graco Headquarters: Minneapolis  
International Offices: Belgium, China, Japan, Korea  
GRACO INC. AND SUBSIDIARIES S P.O. BOX 1441 S MINNEAPOLIS MN 55440–1441 S USA  
Copyright 1978, Graco Inc. All Graco manufacturing locations are registered to ISO 9001.  
Revised April 2013  
16 307296  
 

Graco Computer Monitor Sound Sleep User Manual
GTI Indoor Furnishings GLE M4 32 User Manual
HP Hewlett Packard Digital Camera HPD3000 User Manual
HP Hewlett Packard Laptop XU016UT User Manual
HP Hewlett Packard Personal Computer D8C26UTABA User Manual
HP Hewlett Packard Photo Printer Photosmart Printer User Manual
Hunter Fan Air Cleaner 30835 User Manual
Husqvarna Chainsaw 1151470 95 User Manual
Husqvarna Lawn Mower 13 User Manual
Ice O Matic Ice Maker GEM 0650 User Manual