MODEL H8092
31/2 Ton Double Pump
Garage Jack
Specifications
Release
Valve Gear
Maximum Lifting Capacity .....................7000 lbs.
Lifting Range .......................................51⁄4"–193⁄4
"
Weight .......................................................84 lbs.
Jack Handle
Foot
Machine
Label
Pedal
Foot
Pedal
Saddle
Figure 2. Pump pedal and release valve gear.
Figure 1. Model H8092 Identification.
Failure to follow these instructions could
result in serious personal injury or death:
Operation
1. DO NOT overload this jack beyond its
rated capacity. Overloading can cause
the jack to collapse and drop the load.
2. ALWAYS support the vehicle with
appropriately rated support stands
before working under it.
To raise the saddle with the jack handle:
Turn the handle clockwise as far as it will turn
and pump the handle up and down. Turning the
handle clockwise will close the release valve (see
Figure 2).
3. DO NOT attempt to move the vehicle
while the jack is in use.
4. Use only on hard level surfaces like
concrete or asphalt. Other surfaces are
potentially unstable.
5. Center the load on the jack to maintain
proper balance and stability.
6. DO NOT use jack if it begins leaking
fluid or if it sinks when placed under
load. These are indications that the jack
needs to be immediately serviced.
To raise the saddle with the foot pedal:
With the jack handle turned fully clockwise, push
the foot pedal down and release it slowly. Each
pump of the pedal will raise the saddle approxi-
mately two inches.
To lower the saddle:
Slowly turn the jack handle counterclockwise.
If you need help with the Model H8092, call our
Technical Support line at: (570) 546-9663.
COPYRIGHT © DECEMBER, 2006 BY GRIZZLY INDUSTRIAL, INC.
WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE
OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC.
#JC8823 PRINTED IN CHINA
H8092 Main Parts Breakdown
��
��
��
��
�
��
��
�
�
��
��
�
��
�
��
��
��
�
��
��
��
��
��
��
��
��
��
��
��
��
��
��
��
��
��
��
��
��
�
�
�
�
��
�
��
��
��
��
��
��
��
REF PART #
DESCRIPTION
REF PART #
PH8092025
DESCRIPTION
1
PR09M
PW13M
EXT RETAINING RING 20MM
FLAT WASHER 20MM
FRONT WHEEL
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
CYLINDER ASSEMBLY
RELEASE VALVE GEAR
PULL SPRING
2
PH8092026
PH8092027
PH8092028
PB25M
3
PH8092003
PH8092004
PH8092005
PH8092006
PH8092007
PH8092008
PR11M
4
SADDLE
COTTER PIN 4 X 47MM
HEX BOLT M12-1.75 X 25
LOCK WASHER 12MM
PEDAL BASE
5
SADDLE BASE
6
LIFTING ARM
PLW05M
7
SIDE FRAME
PH8092031
PH8092032
PB04M
8
LINKING BLOCK
FOOT PEDAL
9
EXT RETAINING RING 25MM
LINKING BOLT
HEX BOLT M6-1 X 10
HANDLE SOCKET
HANDLE SOCKET SCREW
UPPER HANDLE
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
PH8092010
PLW10M
PH8092034
PH8092035
PH8092036
PH8092037
PB52M
LOCK WASHER 16MM
HEX NUT M16-1.75
LIFTING ARM AXIS
HANDLE SOCKET BOLT
PUMP CORE PIN
PH8092012
PH8092013
PH8092014
PH8092015
PN03M
LOWER HANDLE
HEX BOLT M6-1 X 35
RATCHET AXLE
PH8092039
PW08M
HEX NUT M8-1.25
FLAT WASHER 8MM
LINKING SHAFT
FLAT WASHER 16MM
GEAR
PW01M
PH8092041
PH8092042
PH8092043
PH8092044
PR06M
PH8092018
PH8092019
PLW12M
LOCK WASHER 10M
HEX NUT M10- 1.5
COTTER PIN 2MM X 12MM
EXT RETAINING RING 16MM
LOCK WASHER 8MM
MACHINE LABEL
TORSION SPRING
LOCK WASHER 18MM
HANDLE LINKING BOLT
REAR WHEEL ASSEMBLY
LOCK WASHER 12MM
HEX NUT M12-1.75
PH8092021
PH8092022
PLW05M
PH8092046
PH8092047
PN09M
The machine label warns about hazards and ways to prevent injury. The owner of the jack MUST maintain
the original location and readability of the label. If the label is removed or becomes unreadable, contact
H8092 Hydraulic Pump Parts Breakdown
���
���
���
���
���
���
���
���
���
���
���
���
���
���
���
���
���
���
���
���
���
���
���
���
���
���
���
���
���
���
���
���
���
���
���
���
���
REF PART #
PH8092101
DESCRIPTION
BASE
REF PART #
DESCRIPTION
O-RING
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
PH8092118
PH8092119
PH8092120
PH8092121
PH8092122
PH8092123
PH8092124
PH8092125
PH8092126
PH8092127
PH8092128
PH8092129
PH8092130
PH8092131
PH8092132
PH8092133
PH8092134
PH8092102
PH8092103
PH8092104
PH8092105
PH8092106
PH8092107
PH8092108
PH8092109
PH8092110
PH8092111
PH8092112
PH8092113
PH8092114
PH8092115
PH8092116
PH8092117
STEEL BALL
BALL HEAD
SNAP RING
PUMP CORE
CYLINDER WASHER
RECTANGLE RING
CYLINDER
ADJUSTABLE SPRING
ADJUSTING SCREW
O-RING
SAFETY VALVE SCREW
STEEL BALL
O-RING
RETAINING RING
LEAD WASHER
O-RING
PISTON ROD ASSEMBLY
O-RING
PULL ROD
FILL PLUG
O-RING
OIL TANK
RELEASE VALVE SHAFT
RELEASE VALVE BASE
STEEL BALL
RETAINING RING
O-RING
TOP CAP
SEAL WASHER
SPECIAL HEX SCREW
COTTER PIN
BLOCK LINKAGE
|