Grizzly Automobile Parts T10877 User Manual

MODEL T10877  
CANISTER FILTER  
FOR G0710/G0710P  
INSTRUCTIONS  
For questions or help with this product contact Tech Support at (570) 546-9663 or [email protected]  
Introduction  
Inventory  
This kit includes everything you need to upgrade  
your G0710 or G0710P dust collector with a  
1-micron canister filter and plastic collection bag.  
Description  
Qty  
A. Canister Filter ............................................. 1  
B. Collection Flange........................................ 1  
C. Connection Collar....................................... 1  
D. Bag Clamp.................................................. 1  
E. Collection Bag............................................ 1  
F. Clean-Out Crank Handle Assembly........... 1  
G. Adhesive Foam Strips (Not Shown)  
The canister filter is equipped with an internal  
cleaning system that is operated by the external  
crank handle. Rotating this handle 5 or 6 times  
will knock loose any built-up dust inside the filter,  
thereby improving airflow. The plastic collection  
bag is replaceable, so it can be tied off and dis-  
posed of—without increasing your exposure to  
fine dust.  
Short (For Flange)...................................... 1  
Long (For Filter).......................................... 1  
H. Hardware Bag (Not Shown)  
Flange Screw 14"-20 x 34"........................... 6  
Flat Washer 516" ......................................... 4  
Hex Nut 516"-18 ........................................... 2  
Hex Bolt 516"-18 x 2"................................... 2  
Open-End Wrench 10 x 12mm................... 1  
B
C
A
D
Properly seal all connection points when  
installing filter kit to reduce potential expo-  
sure to fine dust from leaks.  
F
E
Installing Canister Filter  
1. DISCONNECT MACHINE FROM POWER!  
2. Remove bag clamp and filter bag from G0710/  
Figure 1. Model T10877.  
G0710P collector body.  
COPYRIGHT © APRIL, 2015 BY GRIZZLY INDUSTRIAL, INC.  
NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE  
OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC.  
(FOR MODELS MFD. SINCE 03/15) #WK17321 PRINTED IN TAIWAN  
V1.04.15  
 
5
5
7. Install (2) 16"-18 x 2" hex bolts, (4) 16" flat  
8. Attach canister filter to flange with (6) 14"-20 x  
5
3
washers, and (2) 16"-18 hex nuts into con-  
4" flange screws (see Figure 7).  
nection collar, then tighten, making sure  
ridges in collar mate with ridges in flange and  
collector body outlet (see Figure 6).  
9. Attach long foam strip to groove around bot-  
tom of canister filter (see Figure 7).  
Note: Tug flange by hand to make sure it is  
secure before proceeding.  
10. Place collection bag over bottom of canister  
filter and secure with bag clamp, making sure  
clamp is seated in groove over foam strip  
(see Figure 7).  
Bag  
Clamp  
Collector  
Body  
Flange  
Screws  
Canister  
Filter  
Collection  
Bag  
Long Foam  
Strip  
Figure 6. Connection collar secured firmly in  
place around collection flange and outlet.  
Figure 7. T10877 final assembly on dust  
collector.  
 
T10877 Parts Breakdown and List  
27  
10  
26  
25  
26  
31  
4
8
2
11  
12  
15  
24  
9
15  
12  
34  
11  
28  
16  
4
3
6
5
1
6
14  
30  
21  
17  
7
28  
13  
20  
8
29  
19  
17  
12  
15  
18  
32  
23  
22  
33  
REF PART #  
DESCRIPTION  
REF PART #  
DESCRIPTION  
1
PT10877001  
CANISTER FILTER 15" x 16-3/16"  
MAIN SPINDLE  
18  
19  
20  
21  
22  
23  
24  
25  
26  
27  
28  
29  
30  
31  
32  
33  
34  
PT10877018  
PT10877019  
PT10877020  
PT10877021  
PT10877022  
PT10877023  
PT10877024  
PT10877025  
PT10877026  
PT10877027  
PT10877028  
PT10877029  
PT10877030  
PT10877031  
PT10877032  
PT10877033  
PT10877034  
CLEAN-OUT CRANK HANDLE  
HEX BOLT M6-1 X 16  
2
PT10877002  
PT10877003  
PT10877004  
PT10877005  
PT10877006  
PT10877007  
PT10877008  
PT10877009  
PT10877010  
PT10877011  
PT10877012  
PT10877013  
PT10877014  
PT10877015  
PT10877016  
PT10877017  
3
CRANK SPINDLE  
CRANK HANDLE M10-1.5 X 14, 98L  
LOCK NUT M10-1.5  
4
BEVEL GEAR  
5
BEARING PLATE  
COLLECTION BAG 22-3/4" X 30"  
BAG CLAMP  
6
BUSHING  
7
PHLP HD SCR M5-.8 X 10  
SET SCREW 1/4-20 X 5/16  
COLLECTION FLANGE  
CONNECTION COLLAR  
CLEANOUT FLAPPER  
FLAT WASHER 1/4  
SPINDLE BRACKET  
BEARING PLATE  
FLANGE SCREW 1/4-20 X 3/4  
HEX BOLT 5/16-18 X 2  
FLAT WASHER 5/16  
8
9
10  
11  
12  
13  
14  
15  
16  
17  
HEX NUT 5/16-18  
HEX NUT M5-.8  
GASKET (RUBBER)  
PHLP HD SCR M5-.8 X 8  
FLANGE SEAL (FOAM)  
FILTER SEAL (FOAM)  
WRENCH 10 X 12MM OPEN-ENDS  
FLANGE GASKET (FOAM)  
PHLP HD SCR M6-1 X 12  
MOUNTING PLATE  
PHLP HD SCR M5-.8 X 10  
Please Note: We do our best to stock replacement parts whenever possible, but we cannot guarantee that all parts shown here  
are available for purchase. Call (800) 523-4777 or visit our online parts store at www.grizzly.com to check for availability.  
-4-  
Model T10877 (Mfd. 03/15)  
 

Graco Baby Accessories ISPS040AB User Manual
Grundig Car Satellite TV System ST 55 2502 5 TOP User Manual
Hamilton Beach Frozen Dessert Maker 68320 User Manual
Hans Grohe Plumbing Product 92646000 User Manual
Harbor Freight Tools Drill 38142 User Manual
Heath Zenith Door 598 1112 04 User Manual
HTC Lawn Mower Accessory 110163 CZ38 User Manual
Hunter Fan Thermostat 40351 User Manual
Husqvarna Trimmer 327R User Manual
Husqvarna Trimmer 335LS User Manual