Grizzly Nail Gun H2911 User Manual

18 GAUGE BRAD NAILER  
MODEL H2911  
INSTRUCTION MANUAL  
COPYRIGHT © JANUARY, 2002 BY GRIZZLY INDUSTRIAL, INC.  
1821 VALENCIA ST., BELLINGHAM, WA 98227  
WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE  
OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC.  
PRINTED IN TAIWAN  
 
Safety Instructions For Power Tools  
10. USE PROPER EXTENSION CORD  
15. MAINTAIN TOOLS WITH CARE.  
Keep tools sharp and clean for best  
and safest performance. Follow  
instructions for lubricating and  
changing accessories.  
for the tool. Make sure your extension  
cord is in good condition. Conductor  
size should be in accordance with the  
chart below. The amperage rating  
should be listed on the motor or tool  
nameplate. An undersized cord will  
cause a drop in line voltage resulting  
in loss of power and overheating.  
Your extension cord must also con-  
tain a ground wire and plug pin.  
Always repair or replace extension  
cords if they become damaged.  
16. DISCONNECT TOOLS before ser-  
vicing and changing accessories.  
17. REDUCE THE RISK OF UNINTEN-  
TIONAL STARTING. Make sure  
switch is in off position before plug-  
ging in.  
18. USE  
THE  
RECOMMENDED  
Consult the  
ACCESSORIES.  
owner’s manual for recommended  
accessories. The use of improper  
accessories may cause risk of injury.  
Minimum Gauge for Extension Cords  
AMP  
RATING  
0-6  
LENGTH  
50ft  
16  
25ft  
18  
18  
16  
14  
12  
10  
100ft  
16  
14  
14  
12  
19. CHECK DAMAGED PARTS. Before  
further use of the tool, a guard or  
other part that is damaged should be  
carefully checked to determine that it  
will operate properly and perform its  
intended function. Check for align-  
ment of moving parts, binding of  
moving parts, breakage of parts,  
mounting, and any other conditions  
that may affect its operation. A guard  
or other part that is damaged should  
be properly repaired or replaced.  
7-10  
16  
16  
12  
12  
11-12  
13-16  
17-20  
21-30  
10  
No  
10  
11. WEAR PROPER APPAREL. Do not  
wear loose clothing, gloves, neckties,  
rings, bracelets, or other jewelry  
which may get caught in moving  
parts. Non-slip footwear is recom-  
mended. Wear protective hair cover-  
ing to contain long hair.  
20. NEVER LEAVE TOOL RUNNING  
UNATTENDED. Turn the power off,  
and do not leave tool until it comes to  
a complete stop.  
12. ALWAYS USE SAFETY GLASSES.  
Also use face or dust mask if cutting  
operation is dusty. Everyday eye-  
glasses only have impact resistant  
lenses, they are NOT safety glasses.  
21. NEVER ALLOW UNTRAINED  
USERS TO RUN THIS TOOL  
WHILE UNSUPERVISED.  
13. SECURE WORK. Use clamps or a  
vise to hold work when practical. it is  
safer than using your hand and frees  
both hands to operate tool.  
22. IF YOU ARE UNSURE OF THE  
INTENDED OPERATION, STOP  
USING THE TOOL. Seek formal  
training or research books or maga-  
zines that specialize in power tools.  
14. DO NOT OVERREACH. Keep proper  
footing and balance at all times.  
H2911 18 Gauge Brad Nailer  
-2-  
 
Basic Nailer Safety  
In addition to the rules stated in the previ-  
ous section, and those in the warning  
boxes throughout this manual, please  
observe the following safety tips for your  
new nailer:  
1. READ THIS ENTIRE MANUAL  
BEFORE OPERATING THE NAIL-  
ER.  
2. ALWAYS DISCONNECT AIR FROM  
THE NAILER WHENEVER SERVIC-  
ING OR INSTALLING NAILS. During  
maintenance, a nailer connected to  
air may fire accidentally, causing seri-  
ous personal injury.  
3. DO NOT PLACE HANDS NEAR  
NAIL POINT OF ENTRY. Nail can  
deflect and tear through the surface  
of the workpiece, puncturing your  
hand or fingers.  
Operating this nailer can propel  
objects into the air, causing immedi-  
ate eye damage. To protect yourself,  
always wear American National  
Standards Institute (ANSI) approved  
safety glasses or goggles when oper-  
ating this equipment. In addition, this  
nailer discharges at 85-90 decibels.  
To protect your hearing, always wear  
ANSI approved ear protection when  
operating this nailer.  
4. NEVER CONNECT THE NAILER TO  
PRESSURIZED  
OXYGEN  
OR  
OTHER COMBUSTIBLE GASES AS  
A POWER SOURCE. Only use fil-  
tered, lubricated, and regulated com-  
pressed air.  
5. NEVER USE GASOLINE OR  
OTHER FLAMMABLE LIQUIDS TO  
CLEAN THE NAILER. Vapors in the  
tool will ignite by a spark and cause  
the tool to explode.  
6. DO NOT CARRY THE NAILER BY  
ANY OTHER PART THAN THE  
HANDLE, and do not carry the nailer  
by the air hose.  
7. DO NOT KEEP THE TRIGGER  
PULLED ON THE SAFETY YOKE  
MECHANISM WHEN CARRYING  
OR HOLDING THE TOOL.  
Never point this nailer at yourself or  
another person! Always pay attention  
to the direction this nailer is pointed.  
Use this tool with respect and caution  
to lessen the possibility of operator or  
bystander injury. Ignoring this warn-  
ing may result in serious personal  
injury.  
8. DO NOT USE A CHECK VALVE OR  
ANY OTHER FITTING THAT  
ALLOWS AIR TO REMAIN IN THE  
TOOL.  
-3-  
H2911 18 Gauge Brad Nailer  
 
INTRODUCTION  
Most importantly, we stand behind our  
Commentary  
tools. If you have any service questions or  
parts requests, please call or write us at  
the location listed below.  
We are proud to offer the Grizzly Model  
H2911 18 Gauge Brad Nailer. This model  
is part of a growing Grizzly family of fine  
power tools. When used according to the  
guidelines set forth in this manual, you can  
expect years of trouble-free, enjoyable  
operation and proof of Grizzly’s commit-  
ment to customer satisfaction.  
Grizzly Industrial, Inc.  
1203 Lycoming Mall Circle  
Muncy, PA 17756  
Phone: (570) 546-9663  
Fax: (800) 438-5901  
This model features 360˚ adjustable  
exhaust, a convenient side-loading maga-  
zine, a safety trigger and a durable plastic  
carrying case.  
We are pleased to provide this manual  
with the Model H2911. It was written to  
encourage safety considerations and  
guide you through general operating pro-  
cedures and maintenance. This manual  
represents our effort to produce the best  
documentation possible.  
The specifications, details, and pho-  
tographs in this manual represent the  
Model H2911 as supplied when the manu-  
al was prepared. However, owing to  
Grizzly’s policy of continuous improve-  
ment, changes may be made at any time  
with no obligation on the part of Grizzly. If  
you have any comments regarding this  
manual, please write to us at the address  
below:  
Read the manual before assembly  
and operation. Become familiar with  
this tool, its safety instructions, and  
its operation before beginning any  
work. Serious personal injury may  
result if safety or operational infor-  
mation is not understood or followed.  
Grizzly Industrial, Inc.  
Technical Documentation  
P.O. Box 2069  
C
/O  
Bellingham, WA 98227-2069  
H2911 18 Gauge Brad Nailer  
 
-4-  
Compressed Air System  
Safety Yoke Mechanism  
The Model H2911 is designed to be oper-  
ated at 70-110 psi.  
A safety yoke mechanism (bump fire) on  
the nose of the nailer acts as a secondary  
safety device. When the trigger is pressed,  
the nailer will not fire until the safety yoke  
mechanism is depressed.  
Do not exceed the maximum operating  
pressure for your model!  
Before using your new nailer, install the  
included ⁄8" quick connect fitting. Install a  
female 38" fitting on the air hose. Regulate  
the air pressure on your air compressor to  
barely over the minimum psi for your  
model.  
Before you use your nailer for the first time,  
check the safety yoke mechanism to  
ensure proper function. To do this:  
3
1. Make sure the nailer is disconnect-  
ed from the air supply!  
2. Make sure the magazine is empty and  
contains no nails.  
3. Make sure the trigger and the safety  
yoke mechanism move up and down  
without sticking.  
4. Connect the nailer to the air supply.  
5. Without pressing the trigger,  
depress the safety yoke mechanism  
against a scrap piece of wood that is  
clean and free of any knots, nails, or  
other foreign objects. If the nailer  
does not fire, then the safety yoke  
mechanism is working correctly. If the  
nailer does fire when you do this,  
immediately disconnect the nailer  
from the air supply and call our cus-  
tomer service for help.  
Many pneumatic tools benefit from an in-  
line filter/lubricator/regulator unit. This  
attachment is connected by hoses  
between the air compressor and the nailer.  
Using this unit protects your tool from dam-  
aging water build-up, allows you to adjust  
and maintain constant air pressure to your  
tool, and saves you the inconvenience of  
having to manually lubricate your tool  
every time you use it. Check the current  
Grizzly catalog for availability of this unit. If  
you plan on installing a filter/lubricator/reg-  
ulator unit in your compressed air system,  
always follow the connection instructions  
that come with the unit.  
Similarly if the nailer fires when the trigger  
is pulled, without the safety yoke mech-  
anism being depressed, then the nailer is  
not working properly.  
If either of these two conditions develop  
after you have used your nailer for a peri-  
od of time, check the lubrication of these  
mechanisms.  
Exceeding the maximum permissible  
operating pressure may cause the  
nailer to explode, blowing metal frag-  
ments in all directions. To protect  
yourself from serious personal injury,  
DO NOT allow your air compressor to  
exceed the recommended pressure  
when connected to this nailer!  
The safety yoke is  
a
mechanical  
device that can fail. Never rely on the  
safety yoke mechanism as an excuse  
to point the nailer at yourself or any  
bystanders. Serious injury may occur.  
-5-  
H2911 18 Gauge Brad Nailer  
 
OPERATION  
Operating Nailer  
Loading Nailer  
To load your nailer:  
If you have not read the safety instruc-  
tions in this manual, do not operate the  
nailer.  
1. Disconnect the air supply from the  
nailer!  
2. Push the magazine latch in the direc-  
tion shown in Figure 1.  
Before you operate your nailer, place one  
drop of the included oil into the quick con-  
nect fitting where the nailer connects to the  
air supply. Fire the EMPTY nailer 3-4 times  
before beginning, so oil does not come out  
onto the project during regular operation.  
To operate your nailer:  
1. Connect the air supply to the quick  
connect fitting.  
2. Test the loaded nailer for proper brad  
penetration. Hold the nailer perpen-  
dicular to the surface of a piece of  
clean scrap wood that is thick enough  
for the length of brad nails you have  
loaded. Depress the safety yoke  
mechanism on your workpiece.  
3. Before pressing the trigger, make  
sure your free hand is positioned out  
of the way of a potential path of a brad  
nail in case of deflection. (Deflection  
is caused when grain irregularities,  
knots or foreign objects inside the  
wood cause the nail to change its  
path, resulting in the nail puncturing  
the surface of the workpiece as  
shown in Figure 3.)  
Figure 1. Releasing magazine latch.  
3. Pull back the magazine cover until it  
stops.  
4. Point the nailer down and insert a  
stick of brad nails into the magazine  
as shown in Figure 2. Make sure that  
the pointed ends of the nails rest in  
the slot at the bottom of the magazine.  
Figure 2. Loading brad nails into nailer.  
5. Push the magazine cover forward  
until the magazine latch locks in  
place.  
Figure 3. Example of brad nail deflection.  
H2911 18 Gauge Brad Nailer  
-6-  
 
Besides damaging your workpiece,  
deflection can cause injury if your free  
hand is securing the workpiece in the  
location that the nail deflects.  
Cleaning Nailer  
4. Press the trigger. If the brad nail drove  
into the wood far enough, continue  
with your intended operations. If the  
brad nail either went too far or not far  
enough, then adjust the air pressure.  
More air pressure will make the brad  
nail go deeper and less air pressure  
will decrease the brad nail penetra-  
tion.  
Oiling Nailer  
Never use use gasoline or other flam-  
mable liquids to clean this tool.  
Vapors in the tool may ignite, causing  
the tool to explode. Ignoring this  
warning may lead to serious personal  
injury or even death!  
Special oil has been included with your  
new Grizzly nailer to help maintain its use-  
ful life. Place one drop of oil in the nailer air  
inlet (as shown in Figure 4) before every  
use. Wipe off any excess oil near the nail-  
er exhaust to avoid dust build-up. When  
the oil that was included with the nailer has  
been completely used, replace with Grizzly  
Model G2820 pneumatic tool oil.  
Use a good solvent to clean the nose  
assembly of the nailer. Always be sure that  
the nailer is dry before using it again.  
Do not allow dust, chips, sand, etc. into the  
air connectors or into the body of the nail-  
er; this may result in leaks and damage to  
the nailer and the air couplings.  
Another option to manual oiling would be  
to install a lubricator in your air compressor  
line. If your air compressor line already has  
a lubricator, then regular lubrication of your  
nailer will not be necessary. Just make  
sure there is always oil in the lubricator.  
As mentioned before, the best option is to  
install a filter/lubricator/regulator unit such  
as the Grizzly Model H2333 in your air line.  
Figure 4. Lubricating nailer via air inlet.  
-7-  
H2911 18 Gauge Brad Nailer  
 
4. The jammed nail should now be visi-  
ble; remove it with needle nose pliers.  
5. Install the guide cover and check the  
safety yoke mechanism for proper  
operation (following the same instruc-  
tions as mentioned in the Safety sec-  
tion).  
Clearing Jammed Nails  
The most frequent situation with any type  
of nailer is a nail jam. A jammed nail must  
be cleared before using the nailer again.  
The two places where a nail can get  
jammed are the magazine and the dis-  
charge area.  
Guide Cover  
Cap Screws  
Figure 5. Removing guide cover.  
Always disconnect air from nailer  
whenever clearing a jammed nail!  
Depth Adjustment  
1. Rotate the depth adjustment wheel  
(shown in Figure 6) clockwise to  
increase the nail depth.  
To clear a jammed nail from the magazine:  
1. Disconnect the nailer from the air  
supply!  
2. Rotate the finger wheel counter-clock-  
wise to decrease the nail depth.  
2. Open the magazine cover and pull the  
magazine all the way back.  
3. Locate and remove the jammed brad  
nail with a pair of needle nose pliers.  
Close the magazine cover so it latch-  
es.  
To clear a jammed nail from the discharge  
area on the Model H2911:  
1. Disconnect the nailer from the air  
supply! Remove all brad nails from  
the magazine.  
Figure 6. Depth adjustment wheel.  
2. Remove the plastic cover from the  
nose of the nailer.  
3. Loosen the 2 cap screws that secure  
the driver guide cover to the driver  
guide on the nose assembly. Remove  
the driver guide cover. See Figure 5  
to identify these parts.  
H2911 18 Gauge Brad Nailer  
-8-  
 
Replacing Pistons/O-Rings  
If you use your nailer day in and day out,  
Grizzly offers repair pistons as cheap  
insurance against wasted down time and  
lost profits in the event that a piston or pis-  
ton shaft becomes worn out. To replace a  
piston:  
Figure 7. Removing rear cap.  
6. Remove the guide cover from the  
nose assembly by loosening the 2 cap  
screws.  
7. Watch the nose assembly and push  
the top of the piston with your finger.  
You will see the piston shaft slide  
along the guide.  
8. Push the piston shaft back inside the  
nailer until you can grip the piston  
head and remove it from the cylinder.  
9. Place a new O-ring on the new piston  
and apply a thin film of the proper  
lubricating oil on the O-ring.  
10. Insert the new piston in the cylinder.  
Make sure that the grooves on the  
piston shaft line up with those on the  
guide. The new piston should easily  
slide into the cylinder. Do not force  
the piston into the cylinder! If the  
piston is not easily inserted, double-  
check the alignment of the piston  
shaft with the grooves on the guide.  
11. After the piston is inserted correctly,  
replace the guide cover and tighten  
the 2 cap screws. Replace the rear  
cap assembly and tighten the 4 cap  
screws.  
Always disconnect air from nailer  
whenever servicing! During mainte-  
nance, a nailer connected to air may  
fire accidentally, causing serious  
personal injury!  
1. Disconnect the nailer from the air  
supply!  
2. Remove all nails from the magazine  
cartridge.  
3. Remove the 4 cap screws on the back  
of the nailer, near the exhaust port.  
4. Remove the rear cap as shown in  
Figure 7.  
5. The top of the piston should now be  
visible inside the cylinder, which is  
housed in the back of the nailer.  
12. For more assistance, or to install a  
complete O-ring set, refer to the  
appropriate breakdown diagram in the  
back of this manual.  
-9-  
H2911 18 Gauge Brad Nailer  
 
H2911 PART BREAKDOWN  
H2911 18 Gauge Brad Nailer  
 
-10-  
REF PART #  
DESCRIPTION  
REF PART #  
DESCRIPTION  
01 PH2911001 UM HD BOLT  
02 PH2911002 CAP COVER  
03 PH2911003 SEAL  
29 PH2911029 LOCK NUT  
30 PH2911030 POSITIONING PLATE  
31 PH2911031 ADJUSTMENT NUT  
32 PH2911032 GUIDE PLATE  
35A PH2911035A SWITCH  
04 PH2911004 CAP SCREW  
05 PH2911005 SETSCREW  
06 PH2911006 CAP  
36 PH2911036 SET SHAFT  
37 PH2911037 SAFETY LEVER  
38 PH2911038 LOCK WASHER  
39 PH2911039 CAP SCREW  
40 PH2911040 NOSE COVER  
41 PH2911041 CAP SCREW  
42 PH2911042 DRIVER GUIDE CVR  
43 PH2911043 CAP SCREW  
44 PH2911044 CAP SCREW  
45 PH2911045 NOSE  
07 PH2911007 PISTON STOPPER  
08 PH2911008 O-RING  
09 PH2911009 COLLAR  
10 PH2911010 O-RING  
11 PH2911011 SPRING  
12 PH2911012 PISTON HEAD VALVE  
13 PH2911013 O-RING  
14 PH2911014 O-RING  
15 PH2911015 O-RING  
16A PH2911016A PISTON ASSEMBLY  
17 PH2911017 CYLINDER  
18 PH2911018 O-RING  
46 PH2911046 CAP SCREW  
47 PH2911047 BRACKET  
48 PH2911048 CAP SCREW  
49 PH2911049 MAGAZINE  
50 PH2911050 NAIL GUIDE LINER  
51 PH2911051 SPRING  
19 PH2911019 BUMPER  
20 PH2911020 GASKET  
21 PH2911021 O-RING  
22 PH2911022 BODY  
52 PH2911052 PUSHER  
23 PH2911023 CAP SCREW  
24 PH2911024 AIR PLUG  
25 PH2911025 JOINT GUIDE  
26 PH2911026 STEPPED PIN  
27 PH2911027 SPRING  
53 PH2911053 SETSCREW  
54 PH2911054 MAGAZINE COVER  
55 PH2911055 ROLLED PIN  
56 PH2911056 STOPPER  
57 PH2911057 MAGAZINE COVER  
59 PH2911059 SPRING  
28 PH2911028 SAFETY LEVER  
-11-  
H2911 18 Gauge Brad Nailer  
 
TROUBLESHOOTING  
CAUSE  
PROBLEM  
ACTION  
1. O-rings in trigger valve  
housing are damaged.  
1. O-rings must be replaced  
Air leaking at trigger valve  
area.  
&
operation of safety  
yoke must be checked.  
1. Loose screws in housing.  
2. Damaged O-ring.  
3. Damaged bumper.  
1. Tighten screws.  
2. Replace O-ring.  
3. Replace bumper.  
Air leaking between hous-  
ing and hose.  
1. Damaged seal.  
1. Air leaks.  
1. Replace damaged seals.  
Air leaking between hous-  
ing and cap assembly.  
1. Tighten screws and fit-  
tings.  
Tool skips nails while dis-  
charging.  
2. Dirt in nose.  
2. Clean nose.  
3. Dirt or damage prevents  
nails from moving freely in  
magazine.  
3. Clean magazine and  
inspect/repair damage.  
4. Inadequate air flow to tool.  
4. Check fitting, air hose,  
and air compressor.  
5. Replace piston O-ring.  
Lubricate.  
5. Worn O-ring on piston or  
lack of lubrication.  
6. Damaged O-rings on trigger  
valve.  
6. Replace trigger valve O-  
rings.  
7. Worn bumper.  
8. Cap seal leaking.  
7. Replace bumper.  
8. Replace cap seal.  
1. Nailer is not sufficiently lubri-  
cated.  
2. Broken spring in cap  
assembly.  
1. Lubricate nailer.  
2. Replace spring.  
Tool runs slowly or has a  
loss of power.  
3. Exhaust port in cap is  
blocked.  
3. Replace damaged inter-  
nal parts.  
1. Nails are the wrong size.  
2. Nails are bent.  
3. Magazine or nose screws  
are loose.  
1. Use correct nails.  
2. Use undamaged nails.  
3. Tighten magazine and  
nose screws.  
Fasteners frequently jam  
the nailer.  
4. Driver or driver guide are  
worn or damaged.  
4. Replace worn or dam-  
aged parts.  
1. Nail is jammed in maga-  
zine or discharge area.  
1. Clear nailer magazine or  
discharge area.  
Nailer does not fire.  
2. Piston shaft is damaged.  
3. Air pressure too low.  
2. Replace piston shaft.  
3. Check/increase air pres-  
sure.  
H2911 18 Gauge Brad Nailer  
-12-  
 
WARRANTY AND RETURNS  
Grizzly Industrial, Inc. warrants every product it sells for a period of 1 year to the original  
purchaser from the date of purchase. This warranty does not apply to defects due directly  
or indirectly to misuse, abuse, negligence, accidents, repairs or alterations or lack of main-  
tenance. This is Grizzly’s sole written warranty and any and all warranties that may be  
implied by law, including any merchantability or fitness, for any particular purpose, are here-  
by limited to the duration of this written warranty. We do not warrant or represent that the  
merchandise complies with the provisions of any law or acts unless the manufacturer so  
warrants. In no event shall Grizzly’s liability under this warranty exceed the purchase price  
paid for the product and any legal actions brought against Grizzly shall be tried in the State  
of Washington, County of Whatcom.  
We shall in no event be liable for death, injuries to persons or property or for incidental, con-  
tingent, special, or consequential damages arising from the use of our products.  
To take advantage of this warranty, contact us by mail or phone and give us all the details.  
We will then issue you a “Return Number,” which must be clearly posted on the outside as  
well as the inside of the carton. We will not accept any item back without this number. Proof  
of purchase must accompany the merchandise.  
The manufacturers reserve the right to change specifications at any time because they con-  
stantly strive to achieve better quality equipment. We make every effort to ensure that our  
products meet high quality and durability standards and we hope you never need to use this  
warranty.  
Please feel free to write or call us if you have any questions about the machine or the man-  
ual.  
Grizzly Industrial, Inc.  
1203 Lycoming Mall Circle  
Muncy, PA 17756  
Phone: (570) 546-9663  
Fax: (800) 438-5901  
E-Mail:  
Thank you again for your business and continued support. We hope to serve you again  
soon!  
-13-  
H2911 18 Gauge Brad Nailer  
 
WARRANTY CARD  
Name__________________________________________________________  
Street__________________________________________________________  
City____________________State________Zip_________  
Phone Number____________E-Mail___________________FAX____________  
Model #___________________________ Order #_______________________  
The following information is given on a voluntary basis. It will be used for marketing purposes to help  
us develop better products and services. Of course, all information is strictly confidential.  
9. How many of the machines checked above are  
Grizzly? ____________  
1. How did you learn about us?  
___Advertisement  
___Friend  
___Catalog  
___World Wide Web  
___Other__________________________  
___Card Deck  
10. Which portable/hand held power tools do you own?  
Check all that apply.  
___Belt Sander  
___Biscuit Joiner  
___Circular Saw  
___Detail Sander  
___Drill/Driver  
___Orbital Sander  
___Palm Sander  
___Portable Planer  
___Saber Saw  
___Reciprocating Saw  
___Router  
2. What is your annual household income?  
___$20,000-$29,999  
___$30,000-$39,999  
___$40,000-$49,999  
___$50,000-$59,999  
___$60,000-$69,999  
___$70,000-$79,999  
___$80,000-$89,999  
___$90,000 +  
___Miter Saw  
___Other_________________________________  
3. What is your age group?  
___20-29  
11. What machines/supplies would you like Grizzly  
Industrial to carry?  
___50-59  
___60-69  
___70 +  
___30-39  
___40-49  
________________________________________  
________________________________________  
________________________________________  
________________________________________  
4. How long have you been a woodworker?  
___0 - 2 Years  
___2 - 8 Years  
___8 - 20 Years  
___20+ Years  
12. What new accessories would you like Grizzly  
Industrial to carry?  
5. How would you rank your woodworking skills?  
________________________________________  
________________________________________  
________________________________________  
________________________________________  
___Simple  
___Advanced  
___Intermediate  
___Master Craftsman  
6. What stationary woodworking tools do you own?  
Check all that apply.  
13. What other companies do you purchase your tools  
and supplies from?  
___Air Compressor  
___Band Saw  
___Panel Saw  
___Planer  
_________________________________________  
_________________________________________  
_________________________________________  
___Drill Press  
___Power Feeder  
___Radial Arm Saw  
___Shaper  
___Jointer  
___Lathe  
___Drum Sander  
___Dust Collector  
___Spindle Sander  
___Table Saw  
14. Do you think your purchase represents good value?  
___Yes  
___No  
___Mortiser  
___Wide Belt Sander  
___Horiz.Boring Machine  
___Vacuum Veneer Press  
___Other______________________________  
15. Would you recommend Grizzly to a friend?  
___Yes ___No  
16. Would you allow us to use your name as a refer-  
ence for Grizzly customers in your area? Note: We  
never use names more than three times.  
7. How many of your woodworking machines are  
Grizzly? _____________  
___Yes  
___No  
8. Which benchtop tools do you own? Check all  
that apply.  
17.Comments:________________________________  
_________________________________________  
_________________________________________  
_________________________________________  
___1"x42" Belt Sander ___6" - 8" Grinder  
___5" - 8" Drill Press ___Mini Lathe  
___8" Table Saw  
___Scroll Saw  
___8" - 10" Bandsaw  
___Disc/Belt Sander  
___Spindle/Belt Sander ___Mini Jointer  
___10"-12"Thickness Planer  
___Other______________________________  
 
Send a Grizzly Catalog to a friend:  
Name________________________________  
Street________________________________  
City______________State______Zip_______  
FOLD ALONG DOTTED LINE  
Place  
Stamp  
Here  
GRIZZLY INDUSTRIAL, INC.  
P.O. BOX 2069  
BELLINGHAM, WA 98227-2069  
TAPE ALONG EDGES--PLEASE DO NOT STAPLE  
 

Graco Baby Playpen Baby Playpen User Manual
Haier Dishwasher DW12 EFM S User Manual
Harman Kardon Stereo System MAS 101 User Manual
Healthrider Home Gym HRE59020 User Manual
Hotpoint Clothes Dryer NBXR453EVAA User Manual
Hotpoint Washer AQXGF 149 PM User Manual
HP Hewlett Packard Laptop Docking Station Laptop Docking Station User Manual
Husqvarna Chainsaw 345e User Manual
Ice O Matic Refrigerator ICE250 through ICE2100 SERIES User Manual
Impex Home Gym MWB 558 User Manual