Grizzly Spreader T10044 User Manual

MODEL T10044  
80 LB SEED/FERTILIZER  
SPREADER  
INSTRUCTION SHEET  
C
E
F
To reduce the risk of injury when using this  
equipment:  
• Do not allow anyone to operate the  
spreader without proper training.  
• Do not allow children to use spreader.  
• Always wear proper protective gear when  
using the spreader.  
• If an object becomes lodged in the hop-  
per, do not attempt to remove it while the  
impeller is moving.  
D
G
Figure 1. Inventory 1.  
• Keep all hardware tightened to be sure  
the spreader is in safe working order.  
H
Inventory (Figures 1, 2 & 3)  
A. Hopper Assembly (not shown)................... 1  
B. Catch Tray (not shown).............................. 1  
C. Left Wheel Frame....................................... 1  
D. Right Wheel Frame .................................... 1  
E. Handle Assembly ....................................... 1  
F. Support Leg................................................ 1  
G. Connecting Rod.......................................... 1  
H. Gear Box & Axle Assembly........................ 1  
I. Wheels ....................................................... 2  
J. Impeller....................................................... 1  
K. Hairpin Cotter Pin....................................... 1  
L. Lock Nut M5-.8........................................... 1  
M. Hex Bolt M5-.8 X 45................................... 1  
N. Phillips Head Screw M4-.7 X 20 ................ 1  
O. Hex Bolts M6-1 X 45.................................. 2  
P. Inner Axle Bushings ................................... 2  
Q. Hex Bolts M6-1 X 40.................................. 4  
R. Axle End Covers ........................................ 2  
S. Hex Bolts M6-1 X 65.................................. 4  
T. Lock Nuts M6-1.......................................... 8  
U. Flat Washers 6mm..................................... 4  
I
J
Figure 2. Inventory 2.  
L
M
K
N
P
O
R
Q
T
S
U
Figure 3. Inventory 3.  
COPYRIGHT © DECEMBER, 2007 BY GRIZZLY INDUSTRIAL, INC.  
WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE  
OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC.  
#JM10162 PRINTED IN CHINA  
-1-  
T10044 80 lb. Seed/Fertilizer Spreader  
 
5. Insert the hairpin cotter pin into the shaft  
Operation  
located inside the bottom of the hopper.  
The Model T10044 can be used for spreading  
fertilizers or seed. If the product has large clumps,  
place the catch tray on the inner lip of the hopper  
to separate out particles that could clog the impel-  
ler during operation.  
6. Attach the handle assembly to the support  
leg using the M6-1 X 40 hex bolts and the  
remaining M6-1 lock nuts.  
7. Insert the steel wire head of the control cable  
into the small hole located at the end of the  
lever assembly. To make sure that the holes  
in the bottom of the hopper align with the  
holes in the adjustable plate; fully push the  
lever down and check the inside of the hop-  
per to make sure that the adjustable plate is  
closed. Clamp the control cable into the press  
plates by removing and re-installing the two  
Phillips head screws and lock nuts, as shown  
in Figure 7.  
The impeller should move in a clockwise rotation.  
If it does not, disassemble and make sure that  
the hole in the gearbox axle is on the right hand  
side as stated in Step 2, and the protrusion on the  
gearbox is facing towards the back as stated in  
Step 3. To evenly distribute product, the spreader  
should be walked at a brisk pace.  
During operation, push the handle downwards to  
lessen the amount of product being distributed  
and pull up to increase. The wing nut on the lever  
assembly, as shown in Figure 7, can be adjusted  
to facilitate a maximum product distribution for the  
current spreading task.  
Wing Nut  
Maintenance  
To prevent unnecessary wear, the Model T10044  
should be regularly maintained. Thoroughly clean  
the inside of the hopper, adjustable plate and the  
impeller after every use. Product that is left over  
and not removed can impede the impeller during  
future uses. Clean with warm soapy water and  
rinse thoroughly.  
Press Plate  
Steel Wire  
Check the pressure level of the tires before use.  
The maximum pressure for the tires is 24 PSI.  
Figure 7. Control lever assembly.  
The gears in the gear box assembly were lubri-  
cated at the factory. Do not open the gear box or  
dirt may enter and clog the gears.  
-3-  
T10044 80 lb. Seed/Fertilizer Spreader  
 
T10044 Parts Breakdown  
 
 
 
�  
�  
��  
�  
�  
�  
�  
�  
�  
�  
��  
�  
�  
�  
�  
 
�  
�  
�  
�  
�  
�  
�  
�  
�  
�  
�  
�  
�  
 
�  
�  
�  
�  
�  
��  
�  
�  
�  
�  
�  
�  
��  
�  
 
T10044 Parts List  
REF PART #  
DESCRIPTION  
REF PART #  
DESCRIPTION  
1
2
3
4
5
6
7
8
9
PCB27M  
CARRIAGE BOLT M6-1 X 25  
EXT TOOTH WASHER 6MM  
27 PT10044027 RIGHT WHEEL ASSEMBLY FRAME  
28 PT10044028 SPECIAL DISC  
PTLW05M  
PT10044003 SCALE PLATE  
29 PT10044029 RIGHT WHEEL  
PT10044004 ADJUSTMENT LEVER  
PT10044005 RIGHT HALF HANDLE  
PT10044006 LEFT HALF HANDLE  
31 PT10044031 AXLE END COVER  
32 PT10044032 INNER AXLE BUSHING  
33 PT10044033 OUTER AXLE BUSHING  
34 PT10044034 GEAR BOX AND AXLE ASSEMBLY  
PS01M  
PHLP HD SCR M4-.7 X 18  
PT10044008 HANDLE GRIP  
PT10044009 SPACER  
35 PS52M  
36 PB172M  
PHLP HD SCR M4-.7 20  
HEX BOLT M5-.8 X 45  
10 PWN01M  
WING NUT M6-1.0  
37 PT10044037 TOP LINE CLAMP PLATE  
38 PT10044038 CONTROL CABLE  
11 PT10044011 HOPPER  
12 PT10044012 HAIRPIN COTTER PIN  
13 PT10044013 CENTER COVER  
39 PS09M  
40 PT10044040 SPECIAL WASHER  
41 PW03M FLAT WASHER 6MM  
PHLP HD SCR M5-.8 X 10  
14 PB171M  
HEX BOLT M6-1 X 65  
15 PT10044015 ADJUSTABLE PLATE  
42 PT10044042 HANDLE  
16 PW05M  
17 PS02M  
FLAT WASHER 4MM  
43 PT10044043 HOPPER LINE CLAMP  
PHLP HD SCR M4-.7 X 12  
44 PS20M  
PHLP HD SCR M5-.8 X 15  
18 PT10044018 LEFT WHEEL ASSEMBLY FRAME  
19 PT10044019 IMPELLER  
45 PT10044045 LARGE END CAP  
46 PT10044046 SMALL END CAP  
47 PT10044047 CONNECTING ROD  
20 PB52M  
HEX BOLT M6-1 X 35  
LOCK NUT M5-.8  
21 PLN02M  
48 PB71M  
HEX BOLT M6-1 X 45  
22 PT10044022 BOTTOM LINE CLAMP PLATE  
23 PT10044023 TUBE END CAP  
49 PT10044049 LEFT WHEEL  
50 PT10044050 GRIZZLY.COM LABEL  
24 PB47M  
HEX BOLT M6-1 X 40  
LOCK NUT M6-1  
51 PW05M  
FLAT WASHER 4MM  
25 PLN03M  
52 PT10044052 CATCH TRAY  
26 PT10044026 SUPPORT LEG  
 
����  
�  
��  
 
���  
�  
�  
��  
��  
��  
 

Graco Car Seat PD238744A User Manual
Graco Heat Pump 312877C User Manual
Graham Field Wheelchair 565G User Manual
Grizzly Bread Maker H8067 User Manual
Grizzly Lathe G0765 User Manual
Grundig CRT Television LCD 38 605 BS User Manual
Honeywell Smoke Alarm IPGSM DP User Manual
Humminbird Fish Finder LCR 3004 User Manual
Husqvarna Brush Cutter 968999239 User Manual
Igloo Water Dispenser MWC529 User Manual