HP Hewlett Packard Cassette Player HP DDS 3 User Manual

HP DDS-3 Tape Drive  
User’s Guide  
R
Workstation Systems Group  
Order No. A1658–90702  
Edition E1296  
Printed in U.S.A.  
 
Contents  
Preface  
Audience . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . vii  
Safety and Regulatory Statements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . viii  
Installation Notice . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ix  
Related Manuals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  
Revision History . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  
x
x
Questions, Suggestions, or Problems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . xi  
Documentation Conventions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . xi  
Chapter 1  
Introduction  
General Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1–2  
DDS-3 Drive Environmental Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1–3  
DDS-3 Drive Physical Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1–5  
Preparing to Install the DDS-3 Drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1–6  
Tools Required . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1–6  
Verifying Kit Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1–6  
Operating System Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1–6  
Setting the SCSI-2 Address . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1–7  
Address Jumpers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1–8  
Preparing the System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1–11  
SCSI-2 Connection and Termination . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1–12  
Powering Off the Workstation and Any Peripherals . . . . . . . . . . . . . . . . . . . . . . . . . . 1–13  
Adding or Removing the DDS-3 Drive Bezels or Expansion Brackets . . . . . . . . . . . . 1–14  
iii  
 
Contents  
Chapter 2  
Using the DDS-DC Drive  
Your DDS-3 Drive Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2–2  
Controls and Features of the DDS-3 Drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2–2  
LEDs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2–3  
Data Cassettes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2–3  
Media Life . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2–3  
Cleaning the Tape Heads . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2–4  
Media Restrictions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2–4  
Setting the Write-Protect Tab on a Data Cassette . . . . . . . . . . . . . . . . . . . . . . . 2–4  
Using the DDS-3 Drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2–6  
Loading and Unloading a Data Cassette . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2–6  
Verifying the DDS-3 Tape Drive Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2–7  
Media Interchangeability Restrictions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2–7  
Ordering Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2–9  
Chapter 3  
Troubleshooting and Removal/Replacement Procedures  
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3–1  
Checking the Address Settings for Single-Ended Drives . . . . . . . . . . . . . . . . . . . . 3–2  
Checking the Hardware Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3–3  
Rechecking the Address Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3–5  
Verifying the System Operation Using the Support Tools Manager . . . . . . . . . . . . 3–5  
Removal/Replacement Procedures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3–8  
Field Replaceable Units . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3–8  
Powering Off the System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3–8  
Removing and Replacing the DDS-3 Drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3–9  
Adding or Removing the DDS-3 Drive Bezels and Expansion Brackets . . . . . . . . 3–9  
Appendix  
A
SCSI Connector Pinouts  
iv  
 
Contents  
Figures  
1–1. HP DDS-3 Drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1–2  
1–2. HP DDS-3 Drive Physical Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1–5  
1–3. Rear View of DDS-3 Drive and SCSI Address/Jumper Settings . . . . . . . . . . . . . 1–9  
1–4. Switch Settings for Data Compression Mode . . . . . . . . . . . . . . . . . . . . . . . . . . 1–10  
1–5. Adding a Bezel to the DDS-3 Drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1–14  
1–6. Removing a Bezel from the DDS-3 Drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1–15  
1–7 Adding or Removing Expansion Brackets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1–15  
2–1. DDS-3 Drive Controls and Indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2–2  
2–2. Setting the Write-Protect Tab on a DDS Tape . . . . . . . . . . . . . . . . . . . . . . . . . . . 2–5  
2–3. Loading a Data Cassette . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2–6  
3–1. Adding a Bezel to the DDS-D3 Drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3–10  
3–2. Removing a Bezel from the DDS-D3 Drive . . . . . . . . . . . . . . . . . . . . . . . . . . . 3–10  
3–3. Adding or Removing Expansion Brackets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3–11  
Tables  
2–1. LED Display Codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2–3  
2–2. HP DDS Drive Compatibility . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2–8  
A–1. SCSI Connector Pinouts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A–1  
v
 
Preface  
The HP DDS-3 Tape Drive User  
DDS-3 drive.  
s Guide describes how to install, configure, and use the  
We’ve organized this guide as follows:  
Chapter 1  
Chapter 2  
Chapter 3  
Provides a general description of the DDS-3 drive and the procedures for  
installing it into a system.  
Describes the DDS-3 drive configurations, its controls and features, and  
provides directions for using it.  
Provides information on caring for DDS tapes, troubleshooting  
information, and removal/replacement procedures for the DDS-3 drive.  
Appendix A Lists the pinouts for the SCSI connector on the DDS-3 drive.  
Audience  
This guide is intended for use by anyone familiar with the the HP workstations who  
wants to install and configure the DDS drive.  
vii  
 
Preface  
Safety and Regulatory Statements  
See the Owner’s Guide that came with your system for safety informtion.  
Federal Communications Commission (FCC)  
This equipment has been tested and found to comply with the limits for a Class B digital  
device, pursuant to part 15 of the FCC Rules and the Canadian Department of  
Communications. These limits are designed to provide reasonable protection against  
harmful interference in a residential installation. This equipment generates, uses, and can  
radiate radio frequency energy and, if not installed and used in accordance with the  
instructions may cause harmful interference to radio communications. However, there is  
no guarantee that interference will not occur in a particular installation.  
Hewlett-Packard’s system certification tests were conducted with HP-supported  
peripheral devices and HP shielded cables, such as those you receive with your computer.  
Changes or modifications not expressly approved by Hewlett-Packard could void the  
user’s authority to operate the equipment.  
Operation of this device is subject to the following conditions:  
This device may not cause harmful interference.  
This device must accept interference received, including interference that may cause  
undesired operation.  
Cables used with this device must be properly shielded to comply with the  
requirements of the FCC.  
Canadian Department of Communications (CDC)  
This digital apparatus does not exceed the Class A limits for radio noise emissions from  
digital apparatus as set out in the Radio Interference Requirements of the Canadian  
Department of Communications.  
viii  
 
Preface  
Emissions Regulations Compliance  
Any third-party I/O device installed in HP system(s) must be in accordance with the  
requirements set forth in the preceding Emissions Regulations statements. In the event  
that a third-party noncompliant I/O device is installed, the customer assumes all  
responsibility and liability arising therefrom.  
Electrostatic Discharge (ESD) Precautions  
Electrostatic charges can damage the integrated circuits on printed circuit boards. To  
prevent such damage from occurring, observe the following precautions during board  
unpacking and installation:  
Stand on a static-free mat.  
Wear a static strap to ensure that any accumulated electrostatic charge is  
discharged from your body to ground.  
Connect all equipment together, including the static-free mat, static strap, routing  
nodes, and peripheral units.  
Keep uninstalled printed circuit boards in their protective antistatic bags.  
Handle printed circuit boards by their edges, once you have removed them from their  
protective antistatic bags.  
ix  
 
Preface  
Installation Notice  
Products designated in the applicable Hewlett-Packard price list as customer-installable  
can be installed by computer-knowledgeable customers who carefully read and follow the  
instructions provided. Customers who elect to have the product installed by our field  
personnel are charged the applicable field installation charge, as covered under the  
standard terms and conditions. For more information, please contact your local sales  
representative.  
Related Manuals  
For more information, refer to the following documents:  
The Owner’s Guide that came with your system  
HP-UX Installing Peripherals: HP 9000 Series 700 (B2355–90006)  
Using Your HP Workstation (A2615–90003)  
HP Visual User Environment Users Guide (B1171–90061)  
System Administration Tasks HP 9000 Series 700 Computers (B2355–90040)  
Using HP-UX (B2910–90001)  
Documents specific to HP DDS drives:  
Users Manual, Vol 1 of HP DDS Technical Manual (C1534–90911)  
Integration Guide, Vol 2 of HP DDS Technical Manual (C1534–90912)  
The SCSI Interface, Vol 3 of HP DDS Technical Manual (C1534–90913)  
Background to DDS Products, Vol 4 of HP DDS Technical Manual (C1534–90914)  
HP DDS Configuration Guide, Vol 5 of HP DDS Technical Manual (C1534–90915)  
Contact your HP supplier for copies.  
x
 
Preface  
Questions, Suggestions, or Problems  
If you have any questions, suggestions, or problems with our hardware, software, or  
documentation, please call 1–888–301–5932 (U.S. and Canada), or contact the HP  
Response Center for your country.  
Documentation Conventions  
Unless otherwise noted in the text, this guide uses the following symbolic conventions:  
literal values  
Bold words or characters in formats and command descriptions  
represent commands that you must use literally. Pathnames are  
also in bold.  
user-supplied  
values  
Italic words or characters in formats and command descriptions  
represent values that you must supply. Italics are also used in  
text for emphasis.  
screen display  
Information that the system displays appears in this typeface.  
Return  
A rectangle with rounded corners and a key label denotes a key on  
your keyboard. (In this manual we refer to the Return key. On  
your keyboard the key may be labeled either Return or Enter.)  
This symbol indicates the end of a chapter or appendix.  
xi  
 
Chapter 1  
Introduction  
This document describes the HP DDS-3 drive (HP model number C1537A), its  
installation, operation, troubleshooting, and removal/replacement procedures.  
This chapter introduces the DDS-3 drive and contains the following information:  
General description of the drive  
Preparing to install the drive  
Preparing the system  
Powering off the workstation and any peripherals  
Adding or removing the DDS-3 drive bezels or expansion brackets  
1–1  
 
Introduction  
General Description  
The HP DDS-format drives have been developed by Hewlett Packard for data storage  
drives that build on DAT technology. The DDS-3 drive has 12-GB native capacity and  
24–GB compressed capacity. The DDS–3 drive is compatible with all DDS–1 and  
DDS–2 drive formats. Figure 1–1 shows the DDS-3 drive.  
Figure 1–1. HP DDS-3 Drive  
1–2  
 
Introduction  
DDS-3 Drive Environmental Requirements  
The DDS-3 drive has the following environmental requirements:  
Ambient Temperature  
Operating  
5_ C to 40_ C  
(41_ F to 104_ F)  
–40_ C to 70_ C  
(–40_ F to 158_ F)  
Non-Operating  
Humidity  
Operating  
Non-Operating  
20% to 80%RH (non-condensing)  
5% to 95%RH  
Maximum wet bulb temperature = 26_ C  
Vibration  
Operating (3 axes for drives, 1 axis for autoloaders)  
Swept Sine  
Random  
0.3 g peak, 5–500 Hz @ 1 octave/min  
5–350 Hz @ 0.00053 g2/Hz  
HP C1534A/  
36A/53A  
Random  
350–500 Hz @ –6 dB/octave  
500 Hz @ 0.000271 g2/Hz (0.5 g rms)  
5–350 Hz @ 0.0002 g2/Hz  
HP C1533A/  
HP C1537A  
350–500 Hz @ –6 dB/octave  
500 Hz @ 0.0001 g2/Hz (0.3 g rms)  
Non-Operating  
Swept Sine  
Random  
0.75 g peak, 5–500 Hz @ 1 octave/min  
5–100 Hz @ 0.020 g2/Hz  
100–137 Hz @ –6 dB/octave  
137–350 Hz @ 0.0107 g2/Hz  
350–500 Hz @ –6 dB/octave  
500 Hz @ 0.0052 g2/Hz (2.41 g rms)  
1–3  
 
Introduction  
Shock  
Operating (3 axes for drives)  
no performance change  
Operating (3 axes for drives)  
no data loss  
5.0 g peak for 3 ms: half sine  
8.0 g peak for 11 ms: half sine  
0 km to 15.2 km (0 to 50,000 ft)  
Non-Operating (3 axes)  
no damage  
Altitude  
Operating  
Non-Operating  
0 km to 4.6 km (0 to 15,000 ft)  
0 km to 15.2 km (0 to 50,000 ft)  
Transportation  
Vibration Type 1 package (3 axes)  
Swept Sine  
0.5 g peak, 5–200–5 Hz @ 1 octave/min  
5 min dwell at peak resonance  
5–100 Hz @ 0.015 g2/Hz  
Random  
100–200 Hz @ –6 dB/octave  
200 Hz @ 0.0038 g2/Hz(1.47 g rms)  
(30 min/axis)  
Impact Type 1 package  
10 vertical impacts (6 faces and 4 bottom package corners from  
910 mm height)  
Suspended Particles  
Operating and Non–Operating  
Suspended particle environment,  
particles <200 microgram/cubic meter  
Acoustic Noise Emissions  
<5.0 bel soundpower  
1–4  
 
Introduction  
DDS-3 Drive Physical Specifications  
Figure 1–2 describes the physical specifications of the DDS-3 drive.  
41.3 mm  
(1.61 in.)  
+
+
+
60 mm  
(2.34 in.)  
4 mm  
(0.15 in.)  
21 mm  
5 mm  
(0.20 in.)  
(0.82 in.)  
90 mm  
(3.51 in.)  
41.3 mm  
(1.61 in.)  
101.6 mm (3.96 in.)  
150 mm (5.85 in.)  
+
+
101.6 mm  
(3.96 in.)  
94 mm  
(3.66 in.)  
+
+
70 mm  
(2.73 in.)  
30.9 mm  
(1.20 in.)  
3.8 mm  
(.15 in.)  
Figure 1–2. HP DDS-3 Drive Physical Specifications  
1–5  
 
Introduction  
Preparing to Install a New DDS-3 Drive  
The following information describes how to prepare the DDS-3 drive for installation.  
Tools Required  
The following tools are needed to install the DDS-3 drive:  
#2 Phillips screwdriver  
Small needlenose pliers  
T10 torx wrench  
Verifying Kit Contents  
Verify that the kit contains one of each of the following:  
DDS-3 drive (part number 0950–2650) and bezel.  
Set of 4 screws (M4x6)  
Power adapter cable  
Set of two expansion brackets and four screws (M3x6 T10) (not included in all kits)  
SCSI I/O cable  
Static strap  
HP DDS-3 Tape Drive User s Guide (A1658–90702)  
NOTICE: If any contents of your kit are missing, contact your sales  
representative.  
Operating System Support  
The HP DDS-3 drive supports HP-UX 10.01 and later. This drive requires patches  
PHSS_7894 (or equivalent replacement) for support of the Support Tools Manager, and  
patch PHSS_7583 (or equivalent replacement) for offline SCSI testing..  
1–6  
 
Introduction  
Setting the SCSI-2 Address  
The DDS-3 drive must have a unique SCSI-2 target address. The DDS-3 drive jumpers  
are set at the factory to the SCSI-2 default address of 3, as shown in Figure 1–3. We  
recommend that you keep the default address, if possible.  
You must also ensure that the Operation Mode jumpers are set for correct drive operation,  
as shown in Figure 1–4. We ship the drive with the Operation Mode jumpers set to  
operate correctly with your system.  
CAUTION: SCSI tape drives are susceptible to mechanical and electrostatic  
shock. When handling a DDS-3 drive, always wear the static-  
grounding wrist strap that comes in the DDS-3 drive kit, and al-  
ways handle the drive carefully.  
Electrostatic charges can damage drives. To prevent such damage  
from occurring, observe the following precautions during unpack-  
ing and installation:  
D Stand on a static-free mat.  
D Wear a static strap to ensure that any accumulated electrostatic  
charge discharges from your body to ground.  
D Connect all equipment together, including the static-free mat,  
static strap, routing nodes, and peripheral units.  
D Keep uninstalled DDS-3 drives in their protective antistatic  
bags.  
If you need to change the DDS-3 drive address or operation mode, follow these  
instructions, referring to Figures 1–3 and 1–4:  
1. Locate the jumpers at the back of the DDS-3 drive.  
2. To change the jumper settings, use needlenose pliers to set the drive’s SCSI ID to an  
address that is not used by another SCSI device. Check that the other jumpers are set  
correctly.  
1–7  
 
Introduction  
3. If you need to change the Operation Mode switches, locate the switches on the un-  
derside of the DDS-3 tape drive. Switches 1 and 2 are used to configure the data  
compression operation mode. Switches 3 through 8 are used to specify drive connec-  
tivity and functionality according to host or customer requirements. The default set-  
ting is all switches ON.  
Address Jumpers  
To set the drive’s address, use the SCSI-2 address jumpers, and perform the following  
steps:  
1. Attach the static-grounding wrist strap by following the instructions on the package.  
Attach one end of the strap to the system chassis.  
2. Locate the address jumpers on the rear of the DDS-3 drive. Figure 1–3 shows the  
rear of the DDS-3 drive with the significant bits identified.  
3. Set the drive’s SCSI-2 target address to an address that’s not used by another SCSI-2  
device. Using Figure 1–3 as a guide, use needlenose pliers to set the jumpers. When  
finished, refer to “Preparing the System,” later in this chapter, for information on  
verifying the jumpers have been set correctly and your system sees the drive.  
NOTICE: Do not use SCSI-2 address 7 because the system’s SCSI-2  
controller uses address 7 by default. We advise that you do not use  
SCSI-2 address 6 because the root disk drive uses it.  
1–8  
 
Introduction  
Bit 0  
Bit1  
Bit 2  
Term  
PWR  
SCSI Connector  
Power Connector  
SCSI Term  
SCSI Term  
ID  
PWR*  
ID  
PWR*  
Bit  
2
Bit 1  
Bit 0  
Bit 2  
Bit 1  
Bit 0  
0
4
1
2
5
6
3
(Default)  
*Term PWR is not used in HP workstation configurations.  
Figure 1–3. Rear View of DDS-3 Drive and SCSI Address/Jumper Settings  
1–9  
 
Introduction  
Operation Mode  
Switches  
ON  
1
ON  
1
2 3 4 5 6 7 8  
2 3 4 5 6 7 8  
Compression Disabled,  
No Host Control  
Compression Enabled,  
No Host Control  
ON  
ON  
1
2 3 4 5 6 7 8  
1
2 3 4 5 6 7 8  
Compression Disabled, Host  
Can Control Compression  
Compression Enabled,  
With Host Control  
Default Setting  
Figure 1–4. Switch Settings for Data Compression Operation Mode  
1–10  
 
Introduction  
Preparing the System  
Perform the following steps to prepare the system for the DDS-3 drive installation:  
1. Determine the existing SCSI-2 address settings currently in use on your system by  
completing the following steps.  
2. Enter the following at the prompt:  
RETURN  
/usr/sbin/ioscan  
After a few moments the ioscan utility lists all of the SCSI I/O devices it could find.  
The list appears similar to the following:  
H/W Path  
Class  
Description  
============================================  
bc  
8
bc  
I/O Adapter  
8/0  
ext_bus  
target  
GSC built-in Fast/Wide SCSI Interface  
8/0.0  
8/0.0.0  
8/0.5  
disk  
target  
disk  
QUANTUM LPS1080WD  
8/0.5.0  
8/0.6  
DEC  
DEC  
DSP3210SW  
target  
disk  
8/0.6.0  
8/12  
DSP3210SW  
ba  
Core I/O Adapter  
Built-in SCSI  
8/12/5  
8/12/5.3  
8/12/5.3.0  
8/12/5.4  
8/12/5.4.0  
8/12/5.6  
ext_bus  
target  
tape.  
HP C1537A  
target  
disk.  
SEAGATE ST3600N  
target  
1–11  
 
Introduction  
8/12/5.6.0  
disk  
ext_bus  
MICROP 2112  
10  
bc  
I/O Adapter  
10/12  
GSC add-on Fast/Wide SCSI Interface  
10/12.4  
10/12.4.0  
target  
disk  
SEAGATE ST31200W  
3. Shut down the system.  
If you are running HP-UX under HP VUE, shut down your system according to the  
shutdown procedure described in the owner’s guide that came with your worksta-  
tion.  
If you are running HP-UX without HP VUE, shut down your system by typing the  
following command:  
RETURN  
#/etc/shutdown -h  
You must have superuser privileges to use the /etc/shutdown command. If you do  
not have superuser privileges, contact your system administrator.  
If your workstation is part of a cluster, refer to Managing Clusters of HP 9000 Com-  
puters for instructions on shutting down.  
SCSI-2 Connection and Termination  
Only single-ended SCSI-2 configuration is supported.  
Only unshielded connectors can be used.  
The DDS-3 drive does not support termination on the device itself. Normally, drives such  
as this are not required to be at the end of a bus, but if this is unavoidable, HP  
recommends using a feed-through SCSI terminator that plugs directly into the rear of the  
drive.  
1–12  
 
Introduction  
If you do not already have a SCSI terminator, you must order either terminator K2291  
(bale-lock style) or terminator C2904A (thumbscrew style).  
NOTICE: Use care when inserting and removing feed-through terminators to  
avoid damaging the end walls of the terminator and the drive.  
Powering Off the Workstation and Any Peripherals  
To power off the workstation and any peripherals, perform the following steps:  
1. Power off the workstation, using the power switch on the front of the workstation.  
CAUTION: Do not power off your workstation without first shutting down  
HP-UX. Powering off with HP-UX still running could damage the  
data on the disks associated with your workstation.  
If you are already at the boot-administration level (the level used to check the SCSI-2  
IDs), you do not need to shut down before powering off.  
If you accidentally rebooted HP-UX while determining the address settings, see  
“Preparing the System,” earlier in this chapter, for instructions on shutting down HP-UX.  
2. Disconnect the power cord from the rear of the workstation and the wall outlet.  
3. Power off any external peripherals attached to your workstation, and unplug their  
power cables from the wall outlet.  
1–13  
 
Introduction  
Adding or Removing the DDS-3 Drive Bezels or Expansion Brackets  
Depending on the size of the drive opening in your system, you may need to add or  
remove a bezel or expansion brackets to ensure that your DDS-3 drive fits in your  
system.  
Part numbers for the HP bezels are as follows:  
C1533–60104 – 3 1/2 inch Dove Grey  
C1533–60204 – 5 1/4 inch Dove Grey  
C1533–60105 – 3 1/2 inch Flint Grey  
C1533–60205 – 5 1/4 inch Flint Grey  
NOTICE: Before performing any of these changes, make sure there is not a  
cassette in the drive.  
To add a bezel (it can be a 3.5-inch bezel, or a 5.25-inch bezel) to your drive, push the  
bezel onto the drive, making sure the tabs click into place. Refer to Figure 1–5.  
Figure 1–5. Adding a Bezel to the DDS-3 Drive  
1–14  
 
Introduction  
To remove a bezel from a drive, use a straight blade screwdriver to lift the bezel tabs  
from the top of the drive, and push in the tabs at the sides of the drive. Refer to Figure  
1–6.  
Figure 1–6. Removing a Bezel from the DDS-3 Drive  
To add expansion brackets to the drive or to remove them, use a T10 torx wrench to  
either tighten or remove the four torx screws that hold each expansion bracket to the  
drive. Refer to Figure 1–7.  
1–15  
 
Introduction  
Figure 1–7. Adding or Removing Expansion Brackets  
You are now ready to begin the hardware installation of your DDS-3 drive. The  
step-by-step instructions for installing the drive are found in the owner’s guide that came  
with your workstation.  
1–16  
 
Chapter 2  
Using the DDS-3 Drive  
This chapter provides the following information on using your DDS-3 drive:  
DDS-3 drive configuration  
Controls and features of the DDS-3 drive  
Using the DDS-3 drive  
To verify HP-UX system operation, see the owner’s guide that came with your  
workstation.  
For more information on checking or reconfiguring the kernel for a device driver or file,  
see System Administration Tasks Manual: HP 9000 Series 700 Computers.  
2–1  
 
Using Your DDS Drive  
Your DDS-3 Drive Configuration  
Your HP-UX operating system comes with preconfigured device files and drivers. If you  
use these preconfigured device files and drivers, you won’t need to configure your  
DDS-3 drive with the operating system.  
To find out more about creating and using device files, see the owner’s guide that came  
with your system.  
Controls and Features of the DDS-3 Drive  
Your DDS-3 tape drive is either a 3 1/2-inch form factor, or a 5 1/4-inch form factor  
DDS-3 tape drive with data compression and a SCSI interface. It conforms to the DDS-3  
format standard for storing computer data. It’s a high-capacity, high transfer-rate device  
for data storage on tape.  
Figure 2–1 shows the LEDs and eject button of the DDS-3 drive.  
Tape Light Clean/Attention Light  
Eject Button  
Figure 2–1. DDS-3 Drive Controls and Indicators  
2–2  
 
Using Your DDS Drive  
LEDs  
The front panel has two colored LEDs: the Tape Light and the Clean/Attention Light. The  
Tape Light flashes green to show activity (loading, unloading, reading, and writing).  
Steady green means a cartridge is loaded.  
The Clean/Attention Light flashes amber to indicate head cleaning is needed or a  
cartridge is near the end of its life. Steady amber means a hard fault.  
Table 2–1. LED Display Codes  
Tape  
Light  
Clean/  
Attention  
Meaning  
Key  
OFF  
Activity – load or unload  
Activity – read or write  
Cartridge loaded  
Cleaning needed  
Fault  
Steady Green  
Steady Amber  
Flashing Green  
1/2 sec on, 1/2 sec of  
f
f
f
Any  
Any  
Flashing Amber  
1/2 sec on, 1/2 sec of  
Fast Flash Green  
1/4 sec on, 1/4 sec of  
Data Cassettes  
Media Life  
HP DDS data cassettes are currently specified to 2000 passes over any part of the tape  
under optimal environmental conditions (50% relative humidity, 22 degrees C). During a  
tape operation, any one area of the tape may have multiple passes over the heads. This  
translates into approximately 200 to 300 backups or restores.  
Under certain conditions, the life of your data cassette is less than 200 to 300 backups or  
restores. Replace your data cassettes after 100 backups or restores if your operating  
conditions meet any of the following criteria:  
2–3  
 
Using Your DDS Drive  
The relative humidity in your operating environment is consistently less than  
50%.  
You know that the backup software you are using makes multiple passes over  
sections of the tape during backups or restores.  
You notice that when you do backups and restores the tape stops and starts fre-  
quently.  
Cleaning the Tape Heads  
Clean the heads of your tape drive after every 25 hours of tape drive use or if the Media  
Wear (Caution) signal is displayed on the LED.  
NOTICE: Only use HP Cleaning Cassettes (HP92283K) to clean the tape  
heads. Do not use swabs or other means of cleaning the tape heads.  
Follow this procedure to clean the tape heads:  
1. Insert the cleaning cassette into the drive. The tape automatically loads the cassette  
and cleans the heads. At the end of the cleaning cycle, the drive ejects the cassette.  
2. Write the current date on the cleaning cassette label so that you know how many  
times you have used it. Discard the cleaning cassette after you have used it 50 times.  
Media Restrictions  
If you interchange media between other HP workstation DDS tape drives, note that data  
cassettes with compressed data can only be read by tape drives that have data  
compression capabilities. This includes data cassettes that contain both compressed and  
noncompressed data.  
Setting the Write-Protect Tab on a Data Cassette  
You can only store or change information on a data cassette when the write-protect tab is  
in the write position. So, before trying to write to the data cassette, make sure that the  
write-protect tab is in the write position, as shown in Figure 2–2.  
2–4  
 
Using Your DDS Drive  
Push tab right  
for write.  
Push tab  
left for  
writeĆprotect.  
Figure 2–2. Setting the Write-Protect Tab on a DDS Tape  
To protect information on a data cassette from being overwritten, set the write-protect tab  
to the write-protect position, as shown in Figure 2–2.  
NOTICE: The write-protect tab should always be in the write position for  
transferring data to a cassette.  
2–5  
 
Using Your DDS Drive  
Using the DDS-3 Drive  
This section describes how to perform tasks with your DDS-3 tape drive.  
Loading and Unloading a Data Cassette  
Follow these steps to load and unload a data cassette from the DDS-3 tape drive:  
1. Insert the data cassette into the drive, as shown in Figure 2–3.  
Eject Button  
Figure 2–3. Loading a Data Cassette  
2–6  
 
Using Your DDS Drive  
2. Push the data cassette about three quarters of an inch into the drive. The drive  
automatically pulls the data cassette the rest of the way in. When the Tape LED on  
the left front of the drive stops flashing, the drive has loaded the data cassette.  
3. To remove the data cassette, press and release the eject button on the front of the  
drive, as shown in Figure 2–3. The Tape LED on the drive flashes on and off. Ten to  
twenty seconds later, the data cassette slides partway out of the drive. Remove the  
cassette from the drive.  
Verifying the DDS-3 Tape Drive Operation  
To verify that your workstation can communicate with the DDS-3 tape drive, type the  
following:  
Return  
/usr/sbin/ioscan -d stape  
After a few moments the ioscan utility returns a message similar to the following:  
H/W Path  
Class  
Description  
============================================  
bc  
8
bc  
I/O Adapter  
8/12  
ba  
Core I/O Adapter  
Built-in SCSI  
8/12/5  
8/12/5.3  
8/12/5.3.0  
ext_bus  
target  
tape  
HP  
HPC1537A  
If your DDS-3 drive is not listed, go to Chapter 3, “Troubleshooting and Removal/  
Replacement Procedures.”  
For information on using device files or archiving data to or from the DDS-3 drive, see  
the owner’s guide that came with your workstation.  
Media Interchangeability Restrictions  
If you interchange media between DDS-format tape drives, note that data cassettes with  
compressed data can only be read by tape drives that have data compression capabilities.  
2–7  
 
Using Your DDS Drive  
Refer to Tables 2–2 and 2–3 for information on which tapes you can use with each of  
HP’s DDS drives.  
Table 2–2. HP DDS Tape Drive Capability Without Data Compression  
Full Height 5 1/4 DDS-DC DDS-2 DDS-3  
Tape Length  
inch DDS Tape  
Drive  
Tape Drives  
Tape Drives  
Tape Drives  
60 meter  
90 meter  
120 meter  
125 meter  
1.3 GB  
1.3 GB  
2.0 GB  
1.3 GB  
2.0 GB  
1.3 GB  
2.0 GB  
4.0 GB  
12.0 GB  
Not Supported  
Not Supported  
Not Supported  
Not Supported  
Not Supported  
4.0 GB  
Not Supported  
Table 2–3. HP DDS Tape Drive Capability With Data Compression  
Tape Length  
Full Height 5 1/4  
inch DDS Tape  
Drive  
DDS-DC  
DDS-2  
ape Drives  
DDS-3  
ape Drives  
Tape Drives  
T
T
60 meter  
90 meter  
120 meter  
125 meter  
2.6 GB  
2.6 GB  
4.0 GB  
2.6 GB  
4.0 GB  
2.6 GB  
4.0 GB  
8.0 GB  
24.0 GB  
Not Supported  
Not Supported  
Not Supported  
Not Supported  
Not Supported  
8.0 GB  
Not Supported  
2–8  
 
Using Your DDS Drive  
Ordering Information  
To order Hewlett-Packard data cassettes and cleaning cassettes for use in your DDS-3  
tape drive, use the following order numbers:  
HP92283A  
HP92283B  
HP92300A  
HPC1517A  
HP92283K  
HP92283L  
Box of five 60-meter DDS data cassettes  
Box of five 90-meter DDS data cassettes  
Box of five 120-meter DDS data cassettes  
Box of five 125-meter DDS data cassettes  
Package of two head-cleaning cassettes  
Lockable storage box for 12 cassettes  
CAUTION: Use only data cassettes labeled as DDS (Digital Data Storage) cas-  
settes. Never use audio cassettes labeled DAT (Digital Audio Tape)  
in your DDS-format drive. Using DAT cassettes could damage  
your drive.  
2–9  
 
Chapter 3  
Troubleshooting and Removal/Replacement Procedures  
This chapter provides the following information on troubleshooting and  
removal/replacement procedures for your DDS-3 drive:  
Checking the address settings  
Checking the hardware installation  
Verifying system operation  
Field Replaceable Units  
Powering off the system  
Removing and replacing the DDS-3 drive  
Adding or removing DDS-3 drive bezels and expansion brackets  
3–1  
 
Troubleshooting and Removal/Replacement Procedures  
Troubleshooting  
If you have trouble with any of these procedures, see the owner’s guide that came with  
your system.  
This chapter explains what to do if you experience problems during the configuration  
process. It also explains how to run the Support Tools Manager or the Extended Self Test  
to verify your system.  
If you are experiencing difficulty booting the system, reconfiguring HP-UX, or using the  
DDS-3 drive, complete each of the following tasks, in the order they are presented, until  
you discover and correct the problem:  
Check the address settings of any single-ended SCSI-2 devices.  
Check that you have installed the hardware correctly.  
Recheck the device list.  
Run verification tests.  
NOTICE: To run xstm on HP–UX 10.01, you need to install patch  
PHSS_7894.  
Checking the Address Settings for Single-Ended Drives  
Check the address settings of each single-ended SCSI-2 device on the bus. Make sure  
that no device has the same address setting as another. If you find two devices with the  
same address, change one of the devices to a different, unused address setting. To check  
the address settings for each single-ended SCSI-2 device, type the following in a terminal  
window or HP-UX command line:  
RETURN  
/usr/sbin/ioscan  
After a few moments the ioscan utility lists all of the SCSI I/O devices it could find. The  
list appears similar to the following:  
3–2  
 
Troubleshooting and Removal/Replacement Procedures  
H/W Path  
Class  
Description  
============================================  
bc  
8
bc  
I/O Adapter  
8/0  
ext_bus  
target  
disk  
target  
disk  
target  
disk  
GSC built-in Fast/Wide SCSI Interface  
8/0.0  
8/0.0.0  
8/0.5  
QUANTUM LPS1080WD  
8/0.5.0  
8/0.6  
DEC  
DEC  
DSP3210SW  
DSP3210SW  
8/0.6.0  
8/12  
ba  
Core I/O Adapter  
Built-in SCSI  
8/12/5  
8/12/5.3  
8/12/5.3.0  
8/12/5.4  
8/12/5.4.0  
8/12/5.6  
8/12/5.6.0  
10  
ext_bus  
target  
tape  
HP C1537A  
target  
disk  
SEAGATE ST3600N  
target  
disk  
MICROP 2112  
bc  
I/O Adapter  
10/12  
ext_bus  
target  
disk  
GSC add-on Fast/Wide SCSI Interface  
10/12.4  
10/12.4.0  
SEAGATE ST31200W  
Checking the Hardware Installation  
Perform the following steps to check the hardware installation:  
CAUTION: The DDS-3 drive is susceptible to mechanical and electrostatic  
shock. When handling the drive, always wear the static strap that  
came in the DDS-3 drive kit. Always handle the drive carefully.  
1. Check that the SCSI-2 terminator is connected to the single-ended SCSI-2 port on  
the rear I/O panel of the system unit (if there are no external SCSI-2 devices), or  
that the last external single-ended SCSI-2 device is terminated.  
3–3  
 
Troubleshooting and Removal/Replacement Procedures  
2. Attach the static-grounding wrist strap by following the instructions on the package  
that contains the strap.  
3. Shut down HP-UX.  
NOTICE: If you are already at the boot administration level, you do not need  
to shut down; skip this step and go on to Step 4.  
If you are running HP-UX under HP VUE, shut down your system by performing  
the shutdown procedure described in the owner’s guide that came with your work-  
station.  
If you are running HP-UX without HP VUE, shut down your system by typing the  
following command:  
RETURN  
#/etc/shutdown -h  
You must have superuser privileges to use the /etc/shutdown command. If you do  
not have superuser privileges, contact your system administrator.  
If your workstation is part of a cluster, refer to Managing Clusters of HP 9000 Com-  
puters for instructions on shutting down.  
4. Power off the workstation, using the power switch on the front of the workstation.  
CAUTION: Do not power off your workstation without first shutting down  
HP-UX. Powering off with HP-UX still running could damage  
the data on the disks associated with your workstation.  
5. Remove the drive and check the jumpers, as described in “Removal/Replacement  
Procedures” at the end of this chapter.  
6. Replace the drive.  
7. Check the cable connections of your DDS-3 drive. Make sure that the connectors are  
aligned and seated correctly.  
3–4  
 
Troubleshooting and Removal/Replacement Procedures  
8. Recheck the device list (see “Rechecking the Address Settings” below).  
Rechecking the Address Settings  
Check the address settings again to see if the drive is now listed (see “Checking the  
Address Settings for Single-Ended Drives,” earlier in this chapter).  
If the DDS-3 drive and all other SCSI-2 devices available to you before you installed the  
DDS-3 drive are now listed, run the system verification test for your software version, as  
explained in the next sections.  
If the DDS-3 drive is still not listed, or one of the SCSI-2 devices available to you before  
you installed the DDS-3 drive is still not listed, contact your service representative.  
Verifying the System Operation Using the Support Tools Manager  
HP-UX uses a diagnostics product called the Support Tools Manager that allows system  
operation verification.  
You can access the Support Tools Manager in a terminal window. If you are using HP  
VUE as your interface, you can also access the Support Tools Manager through the  
sys_admin directory.  
Three interfaces are available with the Support Tools Manager: a command line interface  
(accessed through the cstm command), a menu-driven interface (accessed through the  
mstm command), and the graphical user interface (accessed through the xstm  
command).  
For more information on these user interfaces, see the online man pages by entering the  
following at a command line prompt:  
RETURN  
man cstm  
RETURN  
man mstm  
RETURN  
man xstm  
3–5  
 
Troubleshooting and Removal/Replacement Procedures  
To access the Support Tools Manager, perform the following steps:  
1. Click on the Terminal Control on the Front Panel of your Workspace.  
Terminal Control  
A terminal window opens.  
2. Move the mouse cursor into the terminal window and click the left mouse button.  
3. Enter the following at the prompt:  
RETURN  
cstm  
The following screen appears:  
Support Tool Manager  
Version A.01.00  
Type ’help’ for a list of available commands.  
CSTM>  
At the CSTM>prompt, you can enter several commands. To see what commands are  
available, type the help command.  
3–6  
 
Troubleshooting and Removal/Replacement Procedures  
4. To verify the system operation, type the following at the CSTM> prompt:  
RETURN  
CSTM>verify all  
Messages similar to the following appear:  
Verification has started on device (CPU).  
Verification has started on device (FPU).  
CSTM>Verification of (FPU) has completed.  
CSTM>Verification of (CPU) has completed.  
RETURN  
5. Press  
to return to the CSTM>prompt after all test results are reported.  
6. To exit the Support Tools Manager, type the following:  
RETURN  
CSTM>exit  
If any tests failed, further diagnosis is necessary by qualified service personnel. Contact  
your designated service representative.  
3–7  
 
Troubleshooting and Removal/Replacement Procedures  
Removal/Replacement Procedures  
The removal/replacement procedures for the DDS-3 drive follow.  
CAUTION: Electrostatic charges can damage the integrated circuits on printed  
circuit boards. To prevent such damage from occurring, follow  
proper ESD precautions.  
Field Replaceable Units  
The following components are authorized for field replacement.  
Description  
Part Number  
DDS-3, Replacement  
DDS-3, Exchange  
C1537–67201  
C1537–69201  
Powering Off the System  
Before performing the removal/replacement procedures, observe the following  
precautions:  
1. Refer to the owner’s guide that came with your system for the procedures to power  
off the system.  
2. Unplug the system unit power cord and the power cords of any peripheral devices  
from the power source.  
3. Unplug the system unit power cord from the back of the system unit.  
WARNING: Failure to properly shut down and remove power from the system can  
create a personal hazard, or may result in hardware damage or data  
corruption.  
3–8  
 
Troubleshooting and Removal/Replacement Procedures  
Removing and Replacing the DDS-3 Drive  
To open your system and to remove and reinstall the DDS-3 drive, refer to the owner’s  
guide that came with your system. Read “Preparing to Install the DDS-3 Drive” in  
Chapter 1 of this guide before beginning an installation.  
Adding or Removing the DDS-3 Drive Bezels and Expansion Brackets  
Depending on the size of the drive opening in your system, you may need to add or  
remove a bezel or expansion brackets to ensure that your DDS-3 drive fits in your  
system.  
NOTICE: Before performing any of these changes, make sure there is not a  
cassette in the drive.  
To add a bezel (it can be a 3.5-inch bezel, or a 5.25-inch bezel) to your drive,  
push onto the drive, making sure the tabs click into place. Refer to Figure 3–1.  
To remove a bezel from a drive, use a straight blade screwdriver to lift the bezel  
tabs from the top of the drive, and push in the tabs on the sides of the drive.  
Refer to Figure 3–2.  
To add or remove expansion brackets to the drive, use a T10 torx wrench to ei-  
ther tighten or remove the four torx screws that hold each expansion bracket to  
the drive. Refer to Figure 3–3.  
3–9  
 
Troubleshooting and Removal/Replacement Procedures  
Figure 3–1. Adding a Bezel to the DDS-3 Drive  
Figure 3–2. Removing a Bezel from the DDS-3 Drive  
3–10  
 
Troubleshooting and Removal/Replacement Procedures  
Figure 3–3. Adding or Removing Expansion Brackets  
3–11  
 
Appendix  
A
SCSI Connector Pinouts  
Table A–1. SCSI Connector Pinouts  
PIN  
1
2
SIGNAL  
GND  
DB(0)  
PIN  
26  
27  
SIGNAL  
TERMPWR  
GND  
3
4
GND  
DB(1)  
28  
29  
GND  
GND  
5
6
7
8
GND  
DB(2)  
GND  
DB(3)  
GND  
DB(4)  
GND  
DB(5)  
GND  
DB(6)  
GND  
DB(7)  
GND  
DB(P)  
GND  
GND  
GND  
GND  
GND  
GND  
OPEN  
30  
31  
32  
33  
34  
35  
36  
37  
38  
39  
40  
41  
42  
43  
44  
45  
46  
47  
48  
49  
50  
GND  
GND  
ATN  
GND  
GND  
GND  
–BSY  
GND  
–ACK  
GND  
–RST  
GND  
–MSG  
GND  
–SEL  
GND  
–C/D  
GND  
–REQ  
GND  
–I/O  
9
10  
11  
12  
13  
14  
15  
16  
17  
18  
19  
20  
21  
22  
23  
24  
25  
A–1  
 
Index  
B
E
bezels, adding or removing, 1–15, 3–10  
environmental requirements, 1–3  
exit command, SupportWave, 3–8  
expansion brackets, adding or  
removing, 1–15, 3–10  
C
commands  
cstm, 3–6  
exit, 3–8  
G
ioscan, 2–7  
verify, 3–8  
general description, 1–2  
cstm command, 3–6  
I
D
indicators, LED, DDS–DC drive, 2–3–  
2–9  
data compression, operation mode, 1–10  
DDS–DC drive  
installation  
cassette, write–protect tab, 2–4–  
2–9  
cleaning the tape heads, 2–4– 2–9  
configuration, 2–2  
controls and features, 2–2  
introduction, 1–1  
LED indicators, 2–3– 2–9  
display codes, 2–3  
OS support, 1–6  
preparing the system, 1–1  
1
adding or removing drive  
bezels or expansion  
brackets, 1–15  
powering off, 1–14  
SCSI–2 connection and  
termination, 1–13  
loading and unloading a cassette,  
2–6  
preparing to install, 1–6  
setting the SCSI–2 address, 1–7  
tools required, 1–6  
media interchangeability  
restrictions, 2–4– 2–9  
media life, 2–3– 2–9  
ordering information, 2–9  
troubleshooting, 3–2–3–12  
using the drive, 2–1  
verifying drive operation, 2–7  
write–protecting a data cassette,  
2–4– 2–9  
verifying kit contents, 1–6  
ioscan command, 2–7  
J
jumpers, SCSI ID, DDS–DC drive, 1–9  
Index-1  
 
L
S
LEDs, DDS–DC drive, 2–3– 2–9  
display codes, 2–3  
SCSI connector pinouts, A–1  
SCSI IDs, jumpers, DDS–DC drive, 1–9  
loading and unloading a data cassette,  
2–6  
SCSI–2 connection and termination,  
1–13  
Support Tools Manager, 3–6–3–12  
system verification tests, 3–6–3–12  
M
media interchangeability restrictions,  
2–8  
T
DDS–DC drive, 2–4– 2–9  
termination, 1–13  
O
troubleshooting  
checking address settings,  
3–2–3–12  
checking hardware installation,  
3–4–3–12  
online help, cstm command, 3–6  
operation mode, switch settings, 1–10  
ordering information, 2–9  
system verification tests, 3–6–3–12  
Support Tools Manager  
,
3–6–3–12  
verifying system operation,  
3–6–3–12  
P
physical specifications, 1–5  
pinouts, SCSI connector, A–1  
V
R
verify command, 3–8  
removal/replacement procedures, 3–9  
verifying the drive operation, 2–7  
Index-2  
 
HP DDS-3 Tape Drive  
User’s Guide  
R
Workstation Systems Group  
Order No. A1658–90702  
Edition E1296  
Printed in U.S.A.  
 
Order Number: A1658–90702  
Edition 1296  
Printed in U.S.A.  
*A1658-90702*  
 

Grizzly Planer G0526 User Manual
Grizzly Router H2854 User Manual
Harbor Freight Tools Cordless Drill 32940 User Manual
Hasbro Games 50644 User Manual
Honeywell Thermometer RCW33W User Manual
Hotpoint Washer 9586 User Manual
Hotpoint Washer Dryer WDL540 P G A K User Manual
HP Hewlett Packard Network Router 11652A User Manual
Image Exercise Bike IMEL39060 User Manual
Impex Home Gym DBR 90 User Manual