Haier Washer Dryer HWM55 10 User Manual

Full Automatic Washing Machine  
with Pump  
User's manual  
This manual is for  
HWM55-10  
Please read this manual  
carefully before using.  
0030806972C  
Retain it for future reference.  
 
Names of the parts  
Top lid A  
Water valve  
Top lid B  
Water absorption cushion  
Cabinet handle  
Detergent box  
Lint filter  
(Installed by user)  
Control panel  
Filter cover  
Inner tub  
Drain hose  
Pulsator  
Control panel film  
Adjustable foot  
Fixed foot (3)  
Cabinet  
ase frame  
ack cover  
Meaning and description of the symbols  
Contents marked with that symbol are related to the  
safety of the product and the personal safety of the  
users. Please operate in strict conformity to the contents,  
otherwise it may cause damage of the machine or  
injure the personal safety of the user.  
Warning sign  
Contents marked with that symbol are actions forbidden  
to perform. Performing of those actions may result  
in damage of the machine or injure the personal  
safety of the user.  
Forbidden sign  
1
 
Safety precautions  
The power cord plug should be convenient  
Please plug the plug on special receptacle  
with rated voltage. Be sure to use single-  
phase three pins receptacle. Ensure the  
earthing prong of the power receptacle is  
earthed reliably. Use leakage protector if  
possible.  
to be pluged in or pluged out with hand  
while the washing machine runs normally.  
Be sure to pull the plug out and close the  
water tap when the machine is idle, when  
moving the machine, or when cleaning  
the machine. Do not use wet hand to ins-  
ert or pull out the power plug.  
Do not damage the power cord, bend , extend, twist, bind or alter it by force.  
Do not press or nip it with weight. If the power cord or the power plug is bad,  
or the power plug becomes flexible, to avoid risk it is required to have it replaced  
by the technicians of our special shop or the after-sale service department.  
Keep the pin of the power plug clean, if the power plug is polluted  
with dust, please wipe with dry cloth carefully.  
Do not put the machine at damp place like  
Do not use water hotter above 50 C .  
the bathroom. Never wash it with water.  
Not put wet laundries on the control panel.  
In case the washing machine is installed  
on ground with carpet, do not block the  
ventilation hole with carpet.  
Do not wash water-proof laundries like  
the raincoat, bike covers etc. to avoid  
abnormal vibrations in spinning.  
The ventilation holes  
at the bottom  
soft items  
Do not let the machine share one receptacle with other  
electric appliances. If the power plug is damaged, or  
the plugging into the receptacle is loose,  
do not use the plug any more.  
2
 
Safety precautions  
Do not stretch hands into the working  
machine. It is dangerous even if the  
rotation is slow. Take special care of  
the children. Do not let the children  
climb the washing machine.  
Do not decompose, repair or alter the  
machine by yourself.  
Do not put any hot or heavy items (such  
as the kettle with hot water ) on the  
washing machine.  
Do not wash laundries with volatile  
materials (such as thinner, petrol etc.)  
r
Petrol  
Thinne  
The handicapped or children without  
care shall not use the machine.  
Keep the machine away from direct  
sunlight and heat source like the heater.  
To prevent the lint inside the tub from blocking  
the cascade outlet during washing, please  
keep the lint filter in good condition, and  
Toprotect your laundries and wash-  
ing machine, please take out all of the  
coins, buttons, sand, hairpin and  
other foreign materials before washing.  
install it to proper position. If the lint filter  
is lost or damaged, please contact the local  
after-sales service department of our company.  
Please check if the water faucet is open,  
and if the connection of the water inlet  
pipe is proper.  
It is suggested to use foamless washing  
powder.  
Install  
Dismantle  
3
 
Installation and adjustment  
Please install and adjust the machine according to the requirement of the manual.  
It is very important to your security and correct operating the machine.  
Install the bottom plate  
Install the lint filter  
After you open the package, please lean  
the washing machine gently down on soft  
items ( like the towel cloth, blanket, etc. ).  
Install the bottom plate to the bottom of the  
machine with the eight screws by a cross  
screwdriver, then lift the machine up gently.  
See to the figure:  
Push the lint filter downward to  
location for lint filter.  
Front  
Back  
Soft items  
Screw  
Bottom plate  
Adjust the installation position  
The largest allowed slope of the  
shank base of the machine is 2  
.
The slanting or rough ground will  
result in unstable running or  
stoppage of the machine. Please  
adjust it with following methods:  
Adjust the adjustable foot:  
1.To twist the adjustable foot, please  
first lift up the side of the foot slightly,  
loosen the adjustable nut, and twist  
the foot.  
adjustable nut  
Fasten  
adjustable foot  
Loosen  
High  
Low  
2.Fasten the nut after adjustment.  
4
 
How to change the direction of the drain hose  
3
protrude the drain hose from the hole  
on the right side of the bottom, and fast  
it onto the bottom with the rack and screws.  
Set the bracket on the drain hose .There  
is a hole on the cabinet to hang the drain  
hose (as figure 3).  
1
Dismount the back cover of the  
washing machine.  
Drain hose rack  
Figure 3  
Figure 1  
4
install the back cover as what it looks  
before.  
2
Take off the drain hose frame. Put  
down the drain hose. Take off the  
drain hose rack. As indicated in  
Figure 1 Pull the drain hose into the  
cabinet from the left side of the bottom  
(as figure 2).  
Figure 2  
Usage of the drain hose  
The drainage shall be smooth with the drain hose  
1.Put the drain hose up to suitable position.  
Do not put it on ground.  
Mouth of  
drain hose  
Notes: the mouth of drain pipe should higher  
than the water level of washing tub for  
avoiding to siphon phenomenon during  
drain.  
Do not tramp or press the drain hose.  
5
 
Install the water inlet hose  
1. Attach the water inlet hoses to the water faucet. Using pliers, tighten  
the coupling. ( As figure 1)  
NOTE: Do not over tighten. Damage to the valves can result.  
2. Connect the other ends to the water inlet valve .  
( As figure 2)  
Jointer of the water inlet hose  
Jointer of the  
water inlet valve  
Figure 2  
Figure 1  
Water absorption cushion  
Check the connection between the jointer of  
the water inlet hose and the water tap  
1.Swaying the hose gently to confirm if it is fastened  
stable.  
2.After installation, open the tap to check if it leaks.  
3.Do not bend the hose with overstrain.  
4.Before each usage please check if the connection  
between the water inlet hose and the water tap is firm,  
so as to prevent dropping from improve Installation  
position.  
Take down the water inlet hose  
1.After using, Close the water tap.  
2. Pull off the water inlet hose from the water tap and washer  
6
 
Preparation before washing  
Preparation before washing  
1.Connect the water inlet hose and open  
the water tap .  
2.Confirm that the washing machine is  
earthed reliably . Then insert the power  
plug into the receptacle. Do not connect  
the earth terminal to the gas pipe and  
tap water pipe.  
3.Hang up the drain hose.  
4.Slanting or uneven ground may result in  
unstable working or abnormal noise. Please  
make the machine stand horizontally.  
Pay attention to followings before washing the laundries  
Confirm  
if  
Clear the pocket. Fasten the The quantity of  
When the pulsator  
the laundries is running , the  
shall not exceed buttons of the  
the rated value. laundries may  
The big laundries cause noise. For  
there's special Take out the  
requirment for coins , sand,  
the laundries. hairpins etc.  
buttons and  
zippers.  
like the jeans  
shall be put in  
loosely.  
t h e s a k e o f  
discretion, please  
put the laundries  
with buttons into  
other laundries.  
a.Please check if the laundries are applicable for washing.  
b.Separate those not colorfast from other laundries.  
c.For laundries not water absorbing, please put them into water with hands.  
d.For laundries with much soil, please remove the soil first. You can add detergent on the  
part with serious soil directly. It is much easier to remove the soil by that mean.  
e.For laundries likely to get lint ball or with long fiber, please first turn the inside out before  
putting them into the water.  
f.Do not put the laundries polluted with chemicals directly into the washing machine.  
g.For those small laundries ,laundries likely to be twisted or worn, and woolen laundries,  
please put them into mesh bag before washing.  
7
 
Put in the laundries  
The capacity of washing and spinning of the  
machine refer to the largest weight of the  
standard laundries under dry condition that  
can be washed or spinned in one time. One  
time washing quantity shall be lower than the  
rated capacity.  
The thickness, size, type ofthe cloth willinf-  
luence the actual washing capacity. It is sui-  
table for one time washing to putin reasona-  
ble amount of laundries and the laundries can  
be turned round in washing.  
Do not select high water level forlaundries  
less than 1.0kg, so asto avoid splashing of  
water.  
To wash thin laundries like the stocking, silk  
etc., please first put them into washing mesh  
bag (which can be purchased separately)  
before wash.  
Usage of the detergent  
How to use the washing  
powder  
Direct dissolved inthe machine  
1.Fill water to"Low" water level.  
2.Add the power. Run for30 seconds  
to dissolve itcompletely.  
3.Put in thelaundries. Select  
suitable water level.  
Inlet box of the detergent  
The instant dissolvingof the washing  
powder:  
1.Prepare warm waterof 30 and a  
container.  
2.Add the powderwhile stirring to  
fully dissolve it.  
Put in theproper quantities detergent  
according to thewater level andthe  
laundries quantities .  
How to usethe whitener  
Fill water to decided level. Dilute  
the whitener with container. Pour  
it slowly into the washing tub.  
Avoid using whitener on  
laundries with color or pattern as  
they are prone to lose color.  
The whitener shall not touch the  
laundries directly.  
It is suggestednot to usehigh  
sudsing detergent.  
Washing powder with poor qualityor  
long time storagemaybe caked.  
Please pay attention to cleaningthe  
detergent box intime  
Refer to the user's manual for  
the usage and quantity of the  
whitener.  
For powder whitener, please  
dissolve it before use.  
8
 
Use the operation buttons  
A.Description of the function of the buttons  
button  
TER LEVEL SELECTION  
WA  
Mode and meaning of indicator light  
Flashing: indicate the running program  
The use selects a suitable water level depending on the load.  
If QUICK WASH is selected water level will indicate  
2
.After  
On: indicate the program about to run,or  
indicate the selected mode  
water level reaches 2,it will wash while water filling, and wash normally  
upon the water level reaching  
4
.
After washing for q min, pressing WATER LEVEL button will enable  
supplemental water filling, which will stop automatically upon the  
water reaching overflow level.  
9
7
5
3
1
10  
8
6
4
2
STANDARD  
JEANS  
SOAK  
WASH  
RINSE  
GENTLE  
QUICK WASH  
SPIN  
WATER LEVEL SELECTION  
PROGRAM SELECTION  
PROCEDURE SELECTION  
button  
PROGRAM SELECTION  
You can select from the following four programs.  
STANDARD  
JEANS  
Normal wash  
Large, thick or heavily soiled laundry  
Woolen textiles or underwear  
button  
PROCEDURE SELECTION  
GENTLE  
With it you can select one or several  
processes of soak,wash,rinse and spin.  
QUICK WASH 10 min quick wash for load below 2kg  
9
 
START/PAUSE button  
POWER ON/OFF button  
After the power is switched on, press it to  
start the machine.  
Press POWER ON/OFF button  
to connect power supply.  
During working, push it to pause.  
During pause, push this button to restart  
and go on working.  
After power is connected, pressing this  
button will cut off the supply.  
SURPLUS(MIN)  
To indicate -- during sensing.  
To indicate remaining min. During  
program running.  
To indicate remaining reserved time  
(hrs) during reservation period.  
To indicate fault symbols for abnormal  
conditions (see page 16)  
SURPLUS(MIN)  
POWER  
ON / OFF  
START  
PAUSE  
+
RESERVATION  
Lock  
button  
RESERVIATION  
Push the button to select the reserve  
washing time from 2 to 24 hours.  
Pressing the button, the numeral tube  
displays the reserved hours to the wash  
cycle end. The point light flashes to  
indicate in-reservation.  
Child safety lock program  
Start up: Push the RESERVATION and SPIN and POWER ON/OFF buttons  
at the same time. After 2 beep sounds, can set the other program. After all  
the program set is finished push the START/PAUSE button, push and hold  
RESERVATION and SPIN buttons for more than 2 seconds at the same  
time. After a beep sound, the child safety lock program works; all buttons  
are locked and cannot be selected.  
Release: push and hold RESERVATION and SPIN buttons for more than  
2 seconds at the same time. After a beep sound, the child safety lock  
program is released.  
Remarks: After pressing POWER ON/OFF to connect power supply, if the washing  
machine lasts idle more than 10 min, it would automatically shut off the supply.  
10  
 
B.Operating procedure and explanations for the  
buttons  
9
7
5
3
1
10  
8
STANDARD  
JEANS  
SURPLUS(MIN)  
6
SOAK  
4
WASH  
RINSE  
GENTLE  
2
QUICK WASH  
SPIN  
POWER  
ON / OFF  
START  
PAUSE  
WATELEVEL SELECTION  
1
PROAM SELECTION  
+
PR3OURE SELECTION  
SERVATION  
Lock  
4
6
2
5
1.Push the POWER ON/OFF button to  
switch on the power  
/
POWER  
ON/OFF  
/
2.Push the PROGRAM SELECTION button to  
select the suitable automatic program  
PROGRAM SELECTION  
After switching on the power, the machine will set to STANDARD program automatically.  
To select other program, push the PROGRAM SELECTION button till the corresponding  
indicator is on. Refer to the PROGRAM SELECTION button in Page 10  
For example: select QUICK WASH for the quick washing of  
the laundries with light dirt.  
Page 10  
In selecting the STANDARD or JEANS programs, the machine will  
execute fuzzy program to control the complete procedure automa-  
tically according to the cloth, weight and water temperature to  
select water level current and washing time.  
3.Push the PROCESS SELECTION button to select  
suitable programs  
PROCEDURE SELECTION  
After switching on the power, the machine will set to wash-rinse-spin program automatically.  
That is the most common program. To select program, push the PROGRAM SELECTION  
button to select one or more programs among soak/wash/rinse/spin. Refer to the Selection  
method of the procedure programs for the selection.  
Page 13  
11  
 
Attention  
Even there's no water inthe tub, the  
spinning will start after acertain period.  
Do not usesoak process forwoolen laundries.  
Wash the laundries that are prone to lose  
colors separately from other laundries.  
The pulsator will not rotate unless the  
water is filled to selected water level.  
Selection method of the procedure programs  
Times of pushing  
the"PROCEDURE  
SELECTION"butto n  
Contents(the nixie tube indicates  
the programs about to run)  
Selected procedure  
selection  
Applicable procedure  
When the common laundries need  
washing,rinsing and spinning.  
Soak  
Wash  
Rinse  
Spin  
Wash, rinse, spin  
0
1
2
3
4
5
Soak Wash Rinse  
Spin  
Spin  
Spin  
Wash(the washing liquid  
remains in the tub)  
Repeat using the washing liquid  
Repeat using the washing liquid  
Soak Wash  
Soak Wash  
Rinse  
Rinse  
Wash,rinse(the rinsing liquid  
remains in the tub)  
When the laundries need rinsing  
and spinning after manual washing  
Rinse,spin  
When the laundries need only  
spinning after manual washing  
(first drain the spin)  
Soak  
Wash  
Rinse Spin  
Spin(spin after drain)  
Soak,wash,rinse,spin  
If the laundries are very dirty,  
or the sleeve and collar are  
dirty,first soakthen wash  
Soak Wash  
Rinse  
Spin  
If you push the "PROCEDURE SELECTION" button for 6 times, it will resume the  
original mode, and it will circulate like that.  
The soak program can be used as fitting of the STANDARD & JEANS automatic  
programs.Soak with slight stirring before wash.  
4.Push the WATER LEVEL button to  
select suitable water level  
WATERLEVEL SELECTION  
When the power is switched on, the washing machine will check the cloth automatically.  
After that, the water level is set automatically. To select other water level, push the  
button. Refer to the Standard usage quantity of the detergent and water quantity and  
WATER LEVEL SELECTION in Page 9 for the selection.  
Page 9  
12  
 
Time list of Each Program(minutes)  
Wash  
(minute)  
Spin  
(minute)  
Water  
level  
Total time (minute)  
Rinse (minute)  
Program  
About 35 47  
About 13 15  
About 13 15  
About 3  
Standard  
Rinse twice,each about 2  
About 6  
About 6  
About 35 47  
Rinse twice,each about 2  
Rinse twice,each about 2  
Rinse once, about 2  
Jeans  
Gentle  
About 24  
About 10  
About 2  
About 4 About 3  
Quick wash  
About 2  
Total time: including the normal water inlet time and drain time.  
Spin time: the time from intermittent running to finishing.  
* The STANDARD and JEANS automatic programs can be fitted with soaking.After  
water inlet, first soak for 15-45 minutes, then do wash.  
* The total washing time may be influenced by the water inlet pressure and water level.  
* When selecting QUICK WASH program,wash,rinse and spin are set automatically.  
5 .Push the " RESERVATION" button  
to select suitable reserve program  
RESERVATION  
After switching on, the washing machinereserved wash programwill be automaticallyset  
inactive. If youdesire a washcycle to endat a reservedtime, you canpress the  
"RESERVATION"button over 2seconds to seta reserved washprogram.  
Refer to The button of "RESERVATION" on page 11.  
SURPLUS(MIN)  
Page 11  
Confirm the reserveprogram  
When "Reservation" becomes active, thenixie tube  
displays the timeto the endof the reservedwash cycle, and  
the indicator turnson.  
To change the runningprogram or cancelthe reservation,  
you should cutoff the supplyand reselect.  
The washing will finish  
about 18 hours later  
6 .Press the "START/PAUSE" button  
START  
PAUSE  
Close the top lid  
Finish washing  
Except water filling and draining, if the  
top cover is opened, the washing  
machine will stop running and alarm.  
The washing machinecuts off thepower supply  
automatically when washcycle ends.  
13  
 
Disposal after washing  
After using, please clean the lint and foreign materials of the lint filter etc. in time.  
Otherwise it may influence your using the machine.  
Please first pull off the power plug from the receptacle before cleaning.  
The lint filter must be used during washing.  
It must be cleaned in time after each using.  
Install  
1. Pull upward to dismantle lint filter.  
Dismantle  
2. Push downward to install lint filter.  
3. Please clean lint filter after wash.  
Clean  
Dismantle & Install  
If the cabinet is dirty, wipe it with wet cloth  
Do not flush it directly with water.  
Wipe it with neutral detergent.  
Do not wipe it with thinner, petrol,  
alcohol etc.  
The filter screen of the water inlet  
valve is likely to be blocked by  
foreign materials andinfluence  
the water inlet. Please clean it  
Alcohol  
Petrol  
Thinner  
1.After washing, close the water faucet. ( If needed, you can dismantle the water inlet hose).  
2.Do not store water in the washing machine for a long period. Drain the water completely after each using.  
3.Be sure to pull off the power plug before maintenance.  
4.Hang up the power cord and drain hose.  
5.Wipe off the water drops on the surface of the machine and inside the tub. Open the top lid for some time  
(about 1 hour), then close the top lid.  
14  
 
Trouble shooting Answer to question  
(If there's breakdown, please pull offthe power plug before checking) Thefollowing phenomena are not breakdowns  
sometimes. Please confirm again before sending it to repair. If there are real breakdowns, please come to the special  
maintenance department or after-sale service department of our company. Do notrepair it by yourself.  
Phenomena  
The reason  
How to settle  
After the reservation is started,  
it rings and the digital tub  
display "E0"  
The top lid is not closed  
Close the top lid  
Clean the foreign material.  
Open and close the top lid once.  
Clean the frozen material.  
Is the drain hose blocked by  
foreign material?  
Is the drain hose frozen?  
After long running of pump in the  
hot weather,power will be cut au-  
tomatically for safe.  
The draining does not work,or  
the speed of draining is too  
slow.The digital tub displays  
"E1" , and it rings.  
Open and close the top lid once.  
Some minutes later the machine will  
continue to work.  
Running pauses during spin,  
The digital tube displays "E2",  
and it rings.  
The top lid is not closed  
Close the top lid  
Safety switch acts, The spin-  
ning cannot work (after twice  
revising). The digital tube dis-  
plays "E3", and it rings.  
Re-order the laundries. Close the  
top lid.  
Level the machine in right position.  
Open and close the top lid once.  
Are the laundries put  
slantingly?  
Is the machine slanting?  
It does not water inlet or the  
speed is slow(the water level is  
not reached after 15 minutes).  
The digital tube displays"E4",  
and it rings.  
Open the waterfaucet. Open  
and close the top lid once.  
Clean the water inlet valve.  
Open and close the top lid  
once.  
The water faucet open or is  
there water supply failure?  
The water inlet valve is blocked  
Is there power failure?  
Is the power plug loose?  
Use it when the power is on  
Insert the power plug tightly.  
The machine does not act.  
(The indicators are off.)  
Is the machine slanting?  
Level the machine properly.  
Re-order the laundries,  
close the top lid.  
Are the laundries slanting  
in spinning?  
There's abnormal sound  
inside the machine  
Is there metal material  
inside the washing mach-  
ine?  
Fasten the buttons and  
zipper.  
Is the jointer screw of the  
water inlet hose is loose or  
twisted awry?  
Fasten the jointer screw  
properly.  
The water faucet leaks  
Common phenomena  
Phenomena  
Explanation  
It is to balance the laundries to avoid slanting.  
The spinning is intermittent when it starts.  
Supplemental water filled after fabric sensor  
has checked fabric(about 48 seconds).  
Pause during washing  
The program issetting the drain time. Acertain  
period is needed before it starts spinning.  
Push the SPIN button, but it doesn't act.  
It is to avoid splashing during water filling.  
The pulsator pauses during water filling in washing and rinsing.  
There may be some water flowing out of the drain  
hose in the first use of the machine.  
It is thewater remained inthe machine duringthe  
ex-factory performance inspection.  
15  
 
Packing list  
Quantity  
Name  
Storage position  
One piece  
User's manual  
Inside the document bag  
Components of the  
water inlet hose  
The side of connection between the water inlet  
hose and the washing machine  
Inside the accessory bag  
One piece  
The side of connection between the jointer of  
the water inlet hose and the water faucet  
Lint filter  
One piece  
One piece  
Inside the document bag  
Bottom plate  
Between the upper cushion of the  
washing machine package and the  
upper seal of the package carton  
Tapping screws  
Five piece  
One set  
Inside the document bag  
Full automatic  
washing machine  
Specifications  
1/18L 2/21L 3/27L 4/32L 5/35L  
6/38L 7/41L 8/44L 9/47L 10/51L  
Water level/Water  
quantity (about)  
Water inlet pressure  
0.03MPa-1MPa  
5.5kg/5.5kg  
Rated washing /  
spinning capacity  
16  
 

GPX TV DVD Combo TD910B User Manual
Grizzly Musical Instrument Amplifier H7580 User Manual
Grizzly Outboard Motor G2908 User Manual
Harbor Freight Tools Soldering Gun 94903 User Manual
Hoshizaki Ice Maker KMH 2000SRH 3 User Manual
Hotpoint Double Oven AHP67X1 User Manual
HP Hewlett Packard All in One Printer M9050 MFP User Manual
Huawei Computer Drive E180 User Manual
Impex Fitness Equipment MD 857 User Manual
Impex Home Gym MWM 1509 User Manual