XPB80-50
Single-tub Washing Machine
Contents
Before using
Names of the parts........... the 2nd cover
Safety precautions ...........................
1
Installation and adjustment ..................3
Using process
Preparation before washing .............. 5
Put in the laundries ............................ 6
Put in the detergent ............................ 7
Select the wash selector...................... 7
Select the wash time .......................... 7
Close the top cover ............................. 8
Finish washing .................................... 8
Disposal after washing .........................8
Trouble shooting.................................9
Packing list...........................................9
Specification................the back cover
Please read this manual carefully before using.
Please retain it attentively for future reference.
Before Using
Safety precautions
Be sure to use three-phase receptacle.
Earth the earthing terminal of the
receptacle reliably.
When the machine is normally using, please
put the power plug at the location easily to
be inserted and extracted by hand. Be sure
to pull the plug off when there'spower failure,
or the machine is being moved, cleaned or
when it is idle.
Earth
If the power cord is bad, to avoid risk it is required to replace it by the technicians of
our special shop or the after-sale service department. Keep the pin of the power
plug clean.
Do not use water hotter than 50 C .
In case the washing machine is installed
on ground with carpet , do not block the
ventilation hole with carpet.
Ventilation hole at
the bottom of the
washing machine
Do not put the machine at damp place
like the bathroom . Never wash it with
water. Do not place wet laundries on the
control panel.
Do not share one receptacle with other
electric appliances. Do not use it in
case that the power plug is damaged
or the inserting into the receptacle is
loose.
Before Using
Safety precautions
Do not stretch hands into the working
machine. It is dangerous even if the
rotation is slow. Take special care of
the children.
Do not decompose, repair or alter the
machine by yourself.
Do not put any hot or heavy items
( such as the kettle with hot water )
on the washing machine.
Do not wash laundries with volatile
materials (such as thinner, petrol etc.).
Petrol
Thinner
Handicapped or children without care
shall not use the machine.
Keep the machine away from direct
sunlight and heat source like the
heater.
Before Using
Installation and adjustment
Please install and adjust the machine according to the requirement of the manual.
It is very important to your security and correct operating the machine.
Usage of the drain hose
The drainage shall be smooth with the drain hose.
1.The height of the drain hose shall be
less than 10cm , or the drainage will
not be smooth enough and cause
incomplete drainage.
<10cm
2.Do not step on or press the drain hose.
3.If extra drain hose is needed , the inner
diameter of the extra hose shall not less
than 30mm, and the length shall not exceed
1.5m.
> 30mm
<1.5m
If the extra hose is too long, cut it either
at point A or B.
A
B
Before Using
Adjust the installation position
The largest permitted slope of the bearing surface of the washing machine is 2.
Slanting or uneven ground will cause unstable operation of the machine. Please
check with following methods:
Hang a becket with weight to confirm if the washing machine is horizontal.
Install the water inlet hose ; Select the water level
Water inlet hose
Water level
indicator
Insert the water inlet hose into the water-inlet
on the control panel directly. ( pull it out to
dismantle it)
Water inlet
MAX
MED
High
about 83L
Fill the water to the water level selected
according to the quantity of the laundries.
Medium
about 68L
Low
about 49L
MIN
Attention:
Do not exceed the " High " water
level , otherwise the water may
overflow out of the machine.
MAX
MED
MIN
Use the quick water inlet
Insert the water-filling jointer into water inlet hose,
then push the water-filling jointer into the water
inlet on the control panel. (To dismantle the water
inlet hose, just push the control handle as
indicated in the figure and pull it out)
Water-filling jointer
Water inlet hose
Fill water into the wash tub directly through
quick water inlet. It can reduce the humidity
inside the control panel significantly and
prolong the operating life of the components.
Push
Control handle
Quick water inlet
Using process
1 Preparation before washing
Preparation before washing
1.Connect the water inlet hose.
2.Confirm that the washing machine is
earthed reliably . Then insert the power
plug into the receptacle. Do not connect
the earth terminal to the gas pipe and
tap water pipe.
3.Hang the drain hose up.
Pay attention to followings before washing the laundries
Confirm
if Clear the pocket. Fasten the
The quantity of
When the pulsator
there's special Take out the
requirement for coins , sand,
the laundries. hairpins etc.
buttons and
zippers.
the laundries is running , the
shall not exceed buttons of the
the rated value. laundries may
The big laundries cause noise. For
like the jeans
shall be put in
loosely.
t h e s a k e o f
discretion,please
put the laundries
with buttons into
other laundries.
Using process
2 Put in the laundries
The capacity of washing of the machine
refer to the largest weight of the standard
laundries under dry condition that can be
washed in one time. Laundries quantity
in one washing cycle shall be lower
than the rated capacity.
The thickness ,size , type of the cloth will
influence the actual washing capacity. It
is suitable to put in reasonable amount of
laundries and the laundries can be turned
round in washing for one time washing.
Do not select " High " water level for
laundries less than 4.0kg, so as to avoid
splashing of water.
Reference weight of the laundries:
working suit up,down
cotton,about 1120g
jeans about 800g
blanket
cotton,about 900g
blending coat
about 800g
pajamas
jacket
cotton,about
800g
shirt
cotton,about
300g
single bed sheet
cotton,about 600g
undershirt
cotton,about 180g
socking
blending,about 50g
underpants
cotton,about 70g
Using process
3 Put in the detergent
How to use the whitener
Fill water to decided level. Dilute the whitener with container. Pour it slowly into the
washing tub.
Avoid using whitener on laundries with color or pattern as they are prone to lose color.
The whitener shall not touch the laundries directly.
Refer to the user's manual for the usage and quantity of the whitener.
For powder whitener,please dissolve it before using.
How to use the washing powder
Direct dissolved in the machine:
1.Fill small quantity of water.
2.Add the powder . Run for 30 seconds to
dissolve it completely.
3.Put it in the laundries. Select suitable
water level.
The powder is more prone to pollute the
laundries than the detergent. Therefore
please use it with proper quantity.
It is suggested not to use high sudsing
detergent.
The instant dissolving of the washing powder:
1.Prepare warm water of 30 C and a container.
2.Add the powder while stirring to fully
dissolve it.
Dosage of different washing powder is
different. Please refer to the instruction
of the washing powder for the detail
dosage.
Selection of the quantity of the washing powder
Standard dosage
Water level
Water quantity
Concentrated washing
powder
Common washing
powder
High (about83L)
Medium (about68L)
Low (about49L)
About
About
About
About
83g
75g
61g
43g
About
68g
About
49g
4 select the wash selector
Please select water current according to the laundries.
5 select the wash time
Please select wash time according to the laundries.
Laundries
Wash time minutes
About2~4
Silk(thin laundries)
Knitwear/chemical fiber
Bed sheet
About3~6
About7~13
About8~10
Cotton,blending,linen
Very dirty and thick laundries
About10~13
Using process
6 Close the top lid
7 Finish washing
The pulsator stops rotating. Put down the drain hose
to discharge the water.
8 Disposal after washing
After using, please clean the lint and foreign materials of the lint filter and lint frame in time.
Otherwise it may influence your using the machine.
Please first pull off the power plug from the receptacle before cleaning.
Cleaning the lint filter
The lint filter must be used during washing.
It must be cleaned in time after each using.
1. Take off the lint filter
Put hand at the indicated position.
Push down to take it off. (See to
Figure 1)
Figure 1
2. Clean the lint
Put it in water and clean while it is still
wet.(See to Figure 2)
3. Install the lint filter
After cleaning, insert the bottom of
the lint filter (marked with "down side")
Figure 2
into the filter frame, then push the
upper part of the filter in (marked with
"up side"). (See to Figure 3)
Figure 3
Attention: be sure not to confuse the direction.
After washing, dismount the water inlet hose.
Pull off the power plug and hang up the
power cord.
Do not store water in the tub for long period.
Discharge the water immediately after each
using.
Wipe the complete unit with soft cloth
twisted dry.
Wipe with neutral detergent if too dirty.
Do not wash it directly by water.
Wipe off the water drops on the surface and
inside the tub with clean soft cloth. Open the
cover of the wash tub for some time (about
one hour), then close it.
Thinner
Petrol
Alcohol
Hang up the drain hose.
Trouble-shooting
The following phenomena are not breakdowns sometimes. Please confirm again before
sending it to repair.
Phenomena
How to check
The washing machine
does not act
Is there power failure?
Is the power plug inserted tightly?
There's abnormal sound
inside the machine.
Is the machine slanting?
Is there metal item inside the tub?
Is the drain hose put down?
Is the drain hose frozen?
Is the front end of the drain hose blocked?
The drainage does not work.
Packing list
User's manual
1pc
1pc
Water inlet hose
Water-filling jointer
Washing machine
1pc
1set
Specification
Type
Single-tub washing machine
Model
XPB80-50
Rated voltage Frequency
Water level Water quantity about
Rated washing capacity kg
Rated input power W
Dimension(mm)
220V~ 50Hz
High/83L Medium/68L Low/49L
8.0
480
L520 W490 H916
16
Weight kg
Injection pressure
0.02MPa~0.2MPa
|