Haier Washer XQS60 78H User Manual

Fuzzy Computerized Automatic  
Washing Machine  
User's manual  
This manual is for  
XQS60-78H  
Please read this manual  
carefully before using.  
Retain it for future reference.  
W
0030804888A  
 
Names of the parts  
Top lid component  
Inner cover component  
Detergent box  
Top lid handle  
Round cover  
liquid whitener inlet  
Control panel  
Attachment block  
(2 pieces)  
Outer tub cover  
Balance ring  
Pulsator  
Water inlet valve  
Lint Filter  
Water absorption  
cushion  
Inner tub  
Front control board  
Cabinet  
Handle  
Power cord  
Drain hose  
Base frame  
Adjustable leg  
Fixed leg (3 pieces)  
Back cover  
Adjustable leg film  
Meaning and description of the symbols  
Warning sign Contents marked with that symbol are related to the safety  
of the product and the personal safety of the users. Please  
operate in strict conformity to the contents, otherwise it may  
cause damage of the machine or injure the personal safety  
of the user.  
Forbidden sign  
Contents marked with that symbol are actions forbidden to  
perform. Performing of those actions may result in damage  
of the machine or injure the personal safety of the user.  
 
Safety precautions  
In normal usage of the washing machine, the power  
Please plug the plug on special 220V AC receptacle.  
Be sure to use single-phase three pins receptacle.  
Ensure the earthing prong of the power receptacle is  
earthed reliably. Use leakage protector if possible.  
plug shall be ready to be pulled or plugged with hang.  
Be sure to pull the plug off and close the water faucet  
when occurring power failure, delivering the maching,  
setting the machine idle or cleaning the machine, do  
not plug or pull the power plug with wet hand.  
Do not bend, stretch, twist, bind the power cord by force, or reform it.  
Do not pressor clamp it with heavy items. If the power cord and power  
plug are bad, or the receptacle is loose, be sure to have it replaced by  
the technicians of our special shop or our agent, or the after-salesservice  
department to avoidany risk. Keep the prong of the power plug clean. If  
dust is found on the power plug, please wipe it off with dry cloth.  
In case the washing machine is installed on ground  
with carpet, be careful not to block the ventilation hole  
with carpet.  
Do not use water with temperature higher than 50  
The ventilation  
holes at the bottom  
Soft items  
Do not wash water-proof laundry like the raincoat,  
bike-covers, down textiles etc. To avoid abnormal  
vibrations in spinning and damages to the laundries-  
Do not put the machine at damp place like the  
bathroom. Never wash it with water. Do not  
put wet laundries on the front control panel board..  
Do not let the machine share one receptacle with other  
electric appliances. If the power plug is damaged, or  
the plugging into the receptacle is loose, do not use  
the plug any more.  
 
Safety precautions  
Do not put hand into the rotating tub. It is dangerous  
even if the rotation speed is slow. Take special care of  
the children. Keep children away from the washing  
machine to avoid them climbing on.  
Do not decompose, repair or alter the machine by  
yourself.  
Do not put any hot or heavy items (such as the  
kettle with hot water) on the washing machine.  
Do not wash laundry with volatile materials  
(such as thinner, petrol etc.).  
Benzene  
Keep the machine away from direct sunlight and  
heat source like the heater.  
The handicapped or children without care shall not  
use the machine.  
Please keep the lint filter in good condition, and  
install it to proper position during washing. If the  
To protect your laundries and washing machine,  
please take out all of the coins, buttons, sand, hairpin  
lint filter is lost or damaged, please contact the local and other foreign materials before washing.  
after-sales service department of our company.  
The front cover of lint filter  
The back cover of lint filter  
dismantle  
Please check if the water faucet is open, and if the  
connection of the water inlet pipe is proper.  
It is suggested to use foamless washing powder.  
install  
 
Installation and adjustment  
Please install and adjust the machine according to the requirement of the manual.  
It is very important to your security and correct operating the machine.  
Install the inner cover component  
1.Open the top lid of the washing machine.  
2.Put the inner cover component on the outer tub cover, aiming the inner cover  
shaft to the installation hole of the corresponding outer tub cover shaft groove.  
3.Firstly insert the inner cover shaft of one side into the corresponding outer tub  
cover shaft groove, then push the another inner cover shaft into the corresponding outer  
tub cover shaft groove. Please install to designated position to guarantee there are no  
dropping or abnormal sound in opening and closing of the inner cover, and the operation  
shall be smooth. Do not dismount the inner cover component after washing.  
Outer tub cover  
Right hand  
Outer tub cover shaft groove  
Left hand  
Inner cover shaft  
Inner cover component  
Figure 2  
Figure 1  
Install the bottom plate  
After opening the package, please lean the washing machine gently down on soft items (like  
towel cloth, blanket, etc.). Install the bottom plate to the bottom of the machine with eight screws  
by a cross screw driver, then lift the machine up gently. See to the figure:  
Front  
Back  
Bottom plate  
Soft items  
Screw  
 
Adjust the Installation position  
The largest allowable slope of the shank base of the machine is 1 . The slanting or rough ground will result in  
unstable running or stoppage of the machine. Please adjust it with following methods:  
Confirm it's horizontal:  
Hang the lead line to check if it is  
horizontal.  
Adjust the adjustable leg:  
1 .To twist the adjustable leg, please first lift up the  
side of the leg slightly, loosen the adjustable nut,  
and twist the leg.  
The adjustable nut  
2 . Afteradjustment, fasten the nut.  
Loosen  
High  
Fasten  
The adjustable feet  
Low  
Usage the drain hose  
The drainage shall be smooth with the drain hose.  
The height of the drain hose shall be less than  
10cm, or the drainage will not be smooth, and cost  
such long time that the machine may stop at mid  
way.  
If extra drain hose is needed, please make separate  
purchase. The inner diameter of the extra hose shall  
not less than 30mm, and the length shall not exceed  
1.5m.  
>
30mm  
Do not step on or press the drain hose.  
<1.5m  
<10cm  
If the drain hose is too long, cut it at mid point. To make  
smooth drainage, cut the front end of the hose slantingly.  
If the extra hose is too long, cut  
it either at A or at B point.  
B
A
 
Install the water inlet hose  
Confirm the water faucet  
water faucet, suitable  
water faucet, not suitable  
The exit end face of the faucet  
It is required that the front end shall be longer than 10mm.  
The exit end face of the faucet shall be flat and smooth. If not please file it to avoid leakage.  
Connection between the water inlet hose jointer  
and the water faucet  
1.Press the lower end of the lock lever and push down the slider. Take off the water inlet hose jointer from the  
water inlet hose component. See to Figure 1.  
2 Loosen the screw till the water faucet can be accessed. Put the jointer of the water inlet hose on the faucet.  
See to Figure 2. (If the faucet is too large and the jointer can not be set on the water faucet, please loosen  
the four screws and take out the bushing in the jointer. The front end of the faucet must be smooth,  
otherwise it may leak water. See to Figure 3.)  
water inlet hose jointer  
Screw  
Slider  
Sign plate  
Bushing  
Lock level  
Screw knife  
water inlet hose  
Figure 2  
Figure 3  
Figure 1  
3.Fasten the four screws evenly. See to Figure 4.  
4 Take off the nameplate. Twist the fastening nut as per the indication of the figure  
to seal up the exit end face of the faucet. See to Figure 5.  
remark: Before installation, the threading is 4mmabove the upper surface of the nut.  
After installation, the threading is 2mm above the upper surface of the nut..(see to figure 6)  
About 4mm before twisting  
About less than 2mm after twisting  
Screw nut  
Figure 6  
Figure 5  
Figure 4  
 
Connection between the water inlet hose and the washer  
1.Do not take off the water absorption cushion. Please check if the  
cushion is dropped or damaged before each usage. If it happens  
please contact our after-sale department immediately.  
nut of the water  
inlet hose  
2 Put the nut of the water inlet hose on the valve jointer.  
3 Fasten the nut. Swing it gently to confirm if it's suitable.  
water absorption  
cushion.  
jointer of the  
water inlet valve  
Connection between the jointer of the water inlet hose  
and the water inlet hose  
1.Push down the slider. Insert the water inlet hose into the jointer.  
the jointer of the  
water inlet hose  
Slider  
2 Hang the lock lever to the jointer. Release the slider till a click  
Locking level  
sound is heard.  
Check the connection between the jointer of the water inlet  
hose and the water faucet  
1.Swing the hose gently to confirm if it is fastened stable.  
2.After installation, open the faucet to check if it leaks.  
3.Do not bend the hose with overstrain.  
4.Before each usage please check if the connection  
between the jointer of the water inlet hose and the  
water faucet, and the installation of the water inlet  
hose are firm, so as to prevent dropping from  
improper installation position.  
Dismantle the water inlet hose  
1. Close the water faucet.  
2. Press the locking lever. Push down the slider. Then pull of the water inlet  
hose.  
Locking level  
Slider  
If the machine is used frequently, the jointer of the water inlet hose can be  
kept on the faucet to prevent damaging the fixing screw.  
 
1 Preparation before washing  
Preparation before washing  
1.Connect the water inlet hose.  
2.Confirm that the washing machine is earthed  
reliably . Then insert the power plug into the  
receptacle. Do not connect the earth terminal  
to the gas pipe and tap water pipe.  
3.Put down the drain hose.  
Pay attention to followings before washing the laundries  
Confirm if there's  
special requirement Take out the coins , and zippers.  
for the laundries. sand,hairpins etc.  
Clear the pocket.  
Fasten the buttons The quantity of the When the pulsator is  
laundries shall not running ,the buttons of  
exceed the rated the laundries may cause  
value. The big noise. For the sake of  
laundries like the discretion ,please put  
jeans shall be put  
in loosely.  
the laundries with  
buttons into other  
laundries.  
a. Check if the laundries are applicable for washing with machine.  
b. Divide the laundries with infest color from other laundries.  
c. Put those laundries difficult to absorb water into water with hand.  
d. For those laundries with heavy soil, please first remove the dirt like mud or dust. For the parts with heavy soil,  
please apply detergent in advance, which can make it easier to remove the soil.  
e. For those laundries that may get lint ball and those with long fur, turn it over before putting in.  
f. Do not put those laundries polluted by chemicals directly into the washing machine.  
 
2 Put in the laundries  
The capacity of washing of the machine refer to  
the largest weight of the standard laundries under  
dry condition that can be washed in one time.  
Laundries quantity in one washing cycle shall  
be lower than the rated capacity. The largest  
capacity of this machine is 6.0 kg.  
The thickness ,size , type of the cloth will influence  
the actual washing capacity. It is suitable to put in  
reasonable amount of laundries and the laundries  
can be turned round in washing for one time  
washing.  
Do not select the higher than "4" water level for  
laundries less than 1.0kg ,so as to avoid splashing  
of water.  
3 Put in the detergent  
Access for detergent and washing powder  
Put the washing powder and softener into the detergent box  
directly as Indicated in the left figure.  
After that, please close the detergent box. Refer to the following  
list for the usage of the detergent :the standard dosage of the  
detergent and the water quantity.  
Access for softener  
How to use softener  
See to the manual of softener for the usage  
and dosage. When adding softener into the  
softener inlet of washing powder box, note  
that it shall not exceed the lower side of the cap.  
Do not leave the softener for long period after  
adding it into the box. Otherwise it may be  
solidified and block the inlet.  
Detergent box  
How to use the whitener  
Fill water to decided level .Dilute the whitener with  
container. Pour it slowly into the washing tub.  
Avoid using whitener on laundries with colour or  
pattern as they are prone to lose colour.  
As the softener is easy to solidify, please clean  
the box frequently. (You shall clean it each time  
you use reserve function).  
Before use softener, you must select to sterilize  
function.  
The whitener shall not touch the laundries directly.  
Refer to the user's manual for the usage and  
quantity of the whitener.  
For powder whitener, please dissolve it before use.  
How to use the washing powder  
Directly dissolved in the machine (not applicable for fuzzy program and reserve wash)  
1.Fill small quantity of water.  
2.Add the powder Run for 30 seconds to dissolve it completely.  
3.Put in the laundry. Select suitable water level.  
The instant dissolving of the washing powder:  
1.Prepare warm water of 30 and a container.  
2.Add the powder while stirring to fully dissolve it In selecting  
The super quick program, it is suggested to adopt liquid detergent instead of washing powder to guarantee the washing effect.  
The powder is more prone to pollute the laundry than the detergent. Therefore please use it with suitable quantity.  
It is suggested not to use high sudsing detergent.  
Washing powder with poor quality or long time storage maybe caked. Please pay attention to cleaning the detergent box in time.  
 
4 Use the operation buttons  
Description of the function of buttons  
Digital tube  
Mode and meaning of the indicators  
During sensing, it displays  
During operation of programs, it displays the remained time  
(minute) or remained times of the corresponding procedure  
Flashing: indicate the running program  
On: indicate the program about to run, or indicate the  
selected mode  
SOAK  
WASH  
RINSE  
SPIN  
RINSE button  
SPIN button  
WASH button  
SOAK button  
Push the RINSE button to set the rinse  
and disinfect procedure.  
Push the SPIN button to set  
the spin procedure.  
Push the WASH button to set  
the wash procedure.  
Push the SOAK button to set  
the soak procedure.  
During STANDARD and JEAN  
programs, push the RINSE button to set  
different rinse times ( 0, 1, 2, 3, 4times).  
During STANDARD and  
JEAN programs, push the  
SPIN button to set different  
spin time (from 0 to 9 minutes)  
During STANDARD and  
JEAN programs, push the  
wash button to set different  
wash time (from 0 to 25 minutes)  
During STANDARD and  
JEAN programs, push the  
SOAK button to set different  
soak time (10,20,30,40 minutes)  
During FIBER and  
During FIBER  
,
COTTON  
,
WOOLLEN and SILK programs, push  
the RINSE button to select rinse  
procedure, but the rinse times cannot  
change.  
During FIBER  
,
COTTON  
,
During FIBER  
,
COTTON  
WOOLLEN and SILK  
WOOLLEN , and SILK  
programs, push the WASH  
button to select wash  
procedure, but the wash time  
cannot change.  
COTTON programs, push  
the soak button to select soak  
procedure, but the soak time  
cannot change.  
programs, push the SPIN  
button to select spin procedure,  
but the spin time cannot change.  
During QUICK  
,
POSTHASTE  
programs, push the RINSE button, the  
machine have no reaction.  
During QUICK  
,
During QUICK  
POSTHASTE , programs,  
push the SPIN button, the  
machine have no reaction.  
During QUICK  
,
POSTHASTE  
,
WOOLLEN  
,
During STANDARD program, the machine  
is set to save water program. If you push  
the rinse button before starting operation, it  
will change to water storage rinse program.  
,
POSTHASTE , programs,  
and SILK programs, push the  
SOAK button, the machine  
have no reaction.  
push the wash button the  
machine have no reaction.  
 
POWER ON/OFF button  
CHILD LOCK FUNCTION  
Push and hold the WATER LEVEL button and SPIN button, then push down the POWER ON/OFF  
button. The digitron displays CL . You can continue setting desired washing procedures.  
After setting, push down the START/PAUSE button. The child lock function is activated. All of  
the buttons are locked and cannot make selection.  
Push the ON/OFF button to switch  
on the power.  
When the power is on, push it  
again to switch off the power.  
Push the ON/OFF button to switch  
on the power.  
Release the child lock function: push down the WATER LEVEL and SPIN button at the same  
time for more than 1 second. After a beep sound, the child lock function is released.  
If the START/PAUSE button is not  
pushed, the washing machine will  
automatically switch off the power  
after 5 minutes.  
RESERVE/REMAIN time indicator digitron  
During sensing, it displays --  
During reserve procedure, it displays the remained reserve time (in  
hours)  
During operation of programs, it displays the remained time (minutes).  
If the remained time exceeds 99 minutes, it adopts A at tens place to  
represent 100 minutes, b to represent 110 minutes. For instance, A3  
represents 103 minutes.  
In case of abnormal phenomenon, it displays  
the abnormal symbol (see to Page 16)  
Page16  
POWER  
ON/OFF  
Time remained  
(minutes)  
START  
PAUSE  
STA  
RT/P  
AUSE  
button  
Reserve  
(hours later)  
After the power is switched on, push it to Start the machine  
During working, push it to pause working.  
During pause, push it to resume working.  
PROGRAM  
lection button  
PROGRAM se  
WATER LEVEL  
Following automatic programs are available for selection  
RESERVE/CALEFACTION  
Applicable situation  
Common washing  
PROGRAM  
STANDARD  
QUICK  
Quick and high-efficiency wash for  
common  
Super quick wash of the laundry under 1 kg  
with light soil  
POSTHASTE  
JEAN  
"RESERVATION/CALEFACTION" button  
Washing the relatively big and thick laundries  
Washing the chemical fiber laundries  
Washing the cotton textiles  
Press "RESERVATION/CALEFACTION"button to set  
reservation or heating Function.  
FIBER  
During machine running, thedigitron indicates the cycle  
remaining time in minutes). Press "RESERVATION  
/CALEFACTION"button, the digitron willIndicate the  
remaining reserved time tocycle end (in hours).Thedigitron  
will indicate the runningstate of the machine.  
COTTON  
WOOLLEN  
SILK  
Washing the woolen textiles  
Washing the textile  
Heating function can beselected if keep pressing  
"RESERVATION/CALEFACTION"Button for morethan 2 s.  
If the decimal pointof digitron is lighted,it means heating  
WATER LEVEL  
butto  
n
The washing machine can detect the laundries automatically.  
After detection, it will set the water level to suitable value among 4, 6,  
8, and 10 automatically.  
You can also set water level by yourself. After the machine is started,  
it will not set water level automatically. You shall push the  
start/pause button to make new setting.  
If there's water inside the tub, the machine cannot detect the  
laundries and will display water level 6 .  
If wet laundries are put in, it may display water level 10 . You must  
set suitable water level by yourself.  
function is selected.The initial temperature isabout 30  
and you can selectyour desired value ina switching  
,
sequence 30  
40  
off 20 . If keep pressingthe  
"RESERVATION/CALEFACTION" button formore than 2 s  
again, the temperature indicatorturns off, andthe  
Reservation can be selected, you can selectreserved time.  
After the machine startsrunning, if selection orcancellation  
of heating function isdesired, you should switchoff the power  
and reselect.  
If POSTHASTE programs selected, it will display water level 3 .  
When water level 2 is reached in water filling, it will perform  
washing while filling water. When water level 3 is reached, it will  
change to normal washing.  
During operation of wash and rinse program, you can push down  
the water level button to add water. When you release the button, or  
it reaches the overflow water level, the machine will stop adding  
water.  
 
Steps of using the operation buttons and description of the steps  
b
POWER  
ON/OFF  
Times  
Time remained  
(Minute)  
START  
PAUSE  
SOAK  
PROGRAM  
WASH  
RINSE  
WATER LEVEL  
SPIN RESERVE/  
1 Push the "POWER ON/OFF " button to switch on the power.  
POWER  
ON/OFF  
2 Push the "PROGRAM" button to select suitable automatic program.  
PROGRAM  
After switching on the power, the machine will set "STANDARD " program automatically. To select  
other automatic program, push the "PROGRAM" button till the relative indicator is on. Refer to the  
"PROGRAM" button on Page 11 for the selection.  
Page 11  
For instance: select "POSTHASTE" program for laundries with small  
quantity and light soil.  
In selecting the •••••••program, the machine  
will execute fuzzy program to select water and wash  
time according to the cloth and weight of the  
laundries. The full procedure is controlled  
automatically.  
FIBER  
STANDARD  
QUICK  
COTTON  
WOOLLEN  
SILK  
POSTHASTE  
JEAN  
3 Push the "SOAK", "WASH", "RINSE" OR "SPIN" button to select suitable procedure.  
Minutes  
Minutes  
SOAK  
WASH  
RINSE  
SPIN  
 
After switching on the power, the washing machine will set to common  
program including"wash, rinse,spin "automatically. To select other  
procedures, push the "SOAK", " WASH", " RINSE" or "SPIN" button  
to select the time of soak, wash and spin, and the times of rinse. After  
switching on the power, if you push one of the button among "WASH",  
"RINSE"and"SPIN", the digitron of the former procedures will turn off  
automatically. The former procedures will not run. For instance: after  
switching on the power. If you push the "SPIN"button first, it will execute  
spin singly after starting.  
Attention  
Even there's no water in the tub, a certain period is  
required before spin starting.  
Do not use the soak program for the woolen textiles.  
Separate the laundries that are not colorfast from  
other laundries in washing.  
The pulsator will not rotate unless the water is  
filled to"3" water level.  
The soak procedure can work in cooperation with automatic programs like standard, jeans,  
fiber and cotton. There is intermittent pulsator stirring during soak.  
After the machine starts operation, you can only set the program and procedure during  
washing, and can not make setting in other cases.  
Press " WATER LEVEL "button,  
select suitable water level  
WATER  
LEVEL  
After switching on the power, the washing machine will execute fuzzy program automatically to  
detect the cloth. After defection, it can set the water level automatically. To select other water  
level, first push the "START/PAUSE"button, then push the "WATER LEVEL" button to set the  
water level. Refer to "water level button"in Page 11 for selection.  
Page 11  
 
Push the "RESERVE/CALEFACTION "button to select suitable  
reserve wash program  
RESERVE/CALEFACTION  
After switching on, the washing machinereserved wash programwill be automaticallyset  
inactive. If youdesire a wash cycle to endat a reservedtime, you canpress the  
"RESERVATION/CALEFACTION" button to set a reserved wash program.  
Refer to The button of "RESERVATION/CALEFACTION" on page 11.  
Page 11  
Confirm the reserveprogram  
When "RESERVATION" becomesactive, the nixie tube displays the time  
to the end of the reserved wash cycle, and the indicator turns on.  
To change the running program or cancel the reservation,  
you should cut off the supplyand reselect.  
the washing will finish  
about 18 hours later  
Confirm the heating function  
Keep pressing the"RESERVATION/CALEFACTION" button for more than 2 s,  
the heating indicator turns on (red).  
Keep pressing the "RESERVATION/CALEFACTION"button for morethan 2 sagain, the  
heating indicator turnsoff and heatingfunction is cancelled.  
After the machinestarts running, ifselection or cancellationof heating function  
is desired, youshould switch offthe power andreselect.  
6.Push the "START/PAUSE " button  
START  
PAUSE  
5 Close the lop lid  
6 Finish washing  
As the top lid opened, the Washer will automatically give an alarm  
and stop running, exclusively during supplying water and rinsing.  
After finishing wash , it will alarm  
automatically.  
 
7.Disposal after washing  
After using, please clean the lint and foreign materials of the lint filter etc. in time. Otherwise it may  
influence your using the machine.  
Please first pull off the power plug from the receptacle before cleaning.  
The lint filter must be used during washing.  
It must be cleaned in time after each using  
Clean the detergent box and set it on  
the control panel seat.  
1.The method of dismantle : Push it up aslant and gently.  
2.The method of install : install it upwards and aslant  
and push it in .  
Lint filter:  
1.Rotate the inner tub with hand till the lint filter reaches  
the position convenient for you to take it off. Pull it up to  
dismount.  
2.Push it down to install.  
3.Clean the filter screen after washing.  
Dismantle  
Dismantle  
Install  
Install  
Dismantle  
Install  
The filter screen of the water inlet valve is likely to be  
blocked by foreign materials and influence the water  
inlet.  
If the cabinet is dirty, wipe it with wet cloth  
Do not flush it directly with water.  
Wipe it with neutral detergent.  
Please clean it with brush every two months.  
Do not wipe it with thinner, petrol, alcohol etc.  
1.After washing, close the water faucet. ( If needed, you can dismantle the water inlet hose).  
2.Do not store water in the washing machine for a long period. Drain the water completely after each using.  
3.Be sure to pull off the power plug before maintenance.  
4.Hang up the power cord and drain hose.  
5.Wipe off the water drops on the surface of the machine and inside the tub. Open the top lid for some time (  
about 1 hour), then close the top lid.  
 
Trouble-shooting Answer to question  
(If there's breakdown, please pull off the power plug before checking) The following phenomena are not breakdowns  
sometimes. Please confirm again before sending it to repair. If there are real breakdowns, please come to the special  
maintenance department or after-sale service department of our company. Do not repair it by yourself.  
Phenomenan  
The reason  
The top lid is opened during reserve  
procedure.  
How to settle  
The digitron displays E0.  
Close the top lid.  
Put down the drain hose. Open and close the  
top lid once.  
The drainage cannot work, or is too slow.  
The digitron displays E1.  
Is the drain hose put down?  
Is the drain hose blocked?  
Clean the foreign material. Open and close  
the top Lid Once.  
Close the top lid.  
It stops running in midway. The digitron  
displays E2.  
The top lid is not closed.  
Reorder the laundries. Close the top lid.  
The machine will start running after 10  
seconds of being placed horizontally.  
The safety switch acts, and the  
spinning cannot work. The  
digitron displays E3.  
Are the laundries put slantingly?  
Is the machine slanting?  
Is the water tap opened, or is there water  
supply failure?  
Is the water inlet valve blocked?  
Is the water pressure too low?  
The water filling does not work, or is  
slow. After about 40 minutes later,  
the digital displays E4.  
Open the water tap. Push the Start/Pause  
button once.  
Clean the water inlet valve then push  
the Start/Pause button once.  
Push the Start/Pause button once.  
Please contact the after-sales service department.  
The digitron displays E5.  
The digitron displays E6.  
The temperature sensor is fallen.  
The water level sensor is bad.  
Please contact the after-sales service department.  
The water level drops to the replacement  
point after it has supplied water for 2 times  
during the whole process.  
The digitron displays F5.  
Open and close the top lid once.  
Please use it when there's power supply.  
Insert the power plug tightly.  
Fill water to the preset position.  
Is there power failure?  
Not wash  
The machine does  
not act  
Is the power plug inserted tightly?  
Is the water level reached preset position?  
Is the power plug inserted tightly?  
Is the top lid closed reliably?  
Are the laundries set flat?  
Insert the power plug tightly.  
Close the top lid.  
Set the laundries flat.  
Adjust the machine to be even  
Reorder the laundries and close the top lid.  
Remove the foreign materials.  
Not spin  
Is the machine slanting?  
Are the laundries put slantingly in spinning?  
Are there any foreign materials?  
There's abnormal sound  
inside the machine  
Is the screw of the jointer of water  
inlet hose loose or awry?  
The water tap leaks  
Fasten the screw of the jointer properly.  
Common phenomena  
Phenomena  
Explanation  
* Balance the laundries to avoid slanting.  
* The spinning is intermittent when it starts.  
* The cloth sensor is detecting the cloth. It will start  
adding water after about 48 seconds.  
* The wash procedure pauses.  
* The program is setting the drain time. A certain  
period is needed before it starts spinning.  
* Select "SPIN" program, but it does not work.  
* The pusaltor pauses during washing , rinsing or  
adding water.  
* It is to avoid splashing during water filling.  
* It is the water remained in the performance  
inspection by the factory.  
* There may be some water flowing out of the  
drain hose in the first use of the machine.  
*
It is the special resume function. In the case of power  
failure or the power plug is loose during washing, the  
machine can save the running program, and resume  
the program after the power supply is recobered. You  
do not need to set the program again.  
*
When the power plug is inserted,computer  
board indicator is switched on,and the machine  
starts working.  
* This is the normal phenomenon .The actual heating  
temperature is also influenced by the atmosphere  
temperature the water temperature for wash and the  
water hardness.  
* The actual heating temperature may have  
discrepancy with the setting level.  
 
Packing list  
Name  
Quantity  
Storage position  
Inside the document bag  
One  
User's manual  
Warranty manual  
Inside the document bag  
One  
Components of the water inlet hose  
The end connecting to thewashing machine  
Jointer connecting the water  
inlet hose and the waterfaucet  
One  
One  
Inside the accessory bag  
The end connecting to thewater  
inlet hose jointer  
Water inlet hose (1 piece)  
Water inlet hose joint (1 piece)  
Between the upper cushion of the  
washing machine package and the  
upper seal of the package carton  
Bottom plate  
Eight  
One  
Tapping screws  
Inside the accessory bag  
Inside the accessory bag  
Inner cover component  
Fuzzy Computerized  
Automatic Washing  
Machine  
One  
Specification  
Rated washing / spinning capacity  
Water level/Water quantity (about)  
6.0kg/6.0kg  
1/12L 2/16L 3/20L 4/25L 5/29L  
6/33L 7/38L 8/42L 9/47L 10/50L  
Injection pressure  
0.03MPa~0.78MPa  
 

Gyration Computer Keyboard GP3200 User Manual
H2O Audio Headphones iSH2 User Manual
Harbor Freight Tools Nail Gun 91053 User Manual
Harbor Freight Tools Planer 10 Auto Planer User Manual
Harbor Freight Tools Saw 93578 User Manual
Hearth and Home Technologies Indoor Fireplace 6000G User Manual
Honeywell Scanner MS7180 User Manual
HP Hewlett Packard Copier 4100N User Manual
HP Hewlett Packard Power Supply 654xA User Manual
IBM Computer Monitor 31P6240 User Manual