Harbor Freight Tools Automobile Accessories 95288 User Manual

MOBILE BASE / 300 LBS CAPACITY  
MODEL 95288  
ASSEMBLY AND OPERATING INSTRUCTIONS  
Due to continuing improvements, actual product may differ slightly from the product described herein.  
®
3491 Mission Oaks Blvd. Camarillo, CA 93011  
Copyright© 2006 by Harbor Freight Tools®. All rights reserved. No portion of this  
manual or any artwork contained herein may be reproduced in any shape or form  
without the express written consent of Harbor Freight Tools.  
ForTechnical questions and replacement parts, please call 1-800-444-3353.  
 
CAUTION: Be aware of dynamic loading. Movement of the Mobile Base under load, or a load  
dropping onto the Mobile Base could create a momentary load exceeding the load capacity of  
300 LBS., which could result in damage to the Mobile Base, and/or personal injury.  
WARNING: The warnings, cautions, and instructions discussed in this instruction manual  
cannot cover all possible conditions and situations that may occur. It must be understood by  
the operator that common sense and caution are factors that cannot be built into this product  
but must be supplied by the operator.  
UNPACKING  
When unpacking, check to make sure all parts listed on page 6 of this manual are included. If any  
parts are missing or broken, please call Harbor Freight Tools® as soon as possible.  
ASSEMBLY INSTRUCTIONS  
1. The Corner Supports (1) will fit wood pieces (not included) of varying lengths,  
depending on the size of the tool to be moved.The sides of the wood should measure  
1-1/4"W X 1-1/4"H in order to slide into the openings in the Corner Supports (1),  
(Illustration 1).  
(Illustration 1)  
2. Mobile Base length would be the length of the tool to which it is to be attached, minus  
1-3/4".This is known as, “Wood-A”, (not included), (Illustration 2).  
3. Mobile Base width would be the width of the tool to which it is to be attached plus 5/8".  
This is known as, “Wood-B”, (not included), (Illustration 2).  
(Illustration 2)  
REV 02/07  
SKU 95288  
For technical questions, please call 1-800-444-3353.  
Page 3  
 
Warning: Be aware when adding wood pieces to corner supports.This Mobile Base,  
like any tool has its limitations. Do not overbuild or overload. Always keep in mind  
theWeight Capacity and the Base size of the tool you wish to load onto this Mobile  
Base.  
4. Use 3/8" drill bit (not included) to drill four holes, two one each side of the ends of  
“Wood A”. Use the pre-drilled holes located in the sides of the Corner Supports as  
guides for where to drill the holes for the Hex Screws. Push one Hex HD Screw (11),  
through each hole with the head of the Screw on the inside of the Corner Support (1),  
and the Lock Nut (16) on the outside, (Illustration 3).  
“Wood A”  
5. Repeat for each of the four Corner Supports (1).  
NOTE: Once assembled, check each of the Corner Supports (1), and all Hex Screws (11),  
and Lock Nuts (16) to make sure all parts are assembled correctly and the Mobile Base is  
stable. Always check for any damaged or worn parts.  
NOTE: Many parts listed and shown are for location illustration only and are not available for  
replacement parts.  
REV 02/07  
SKU 95288  
For technical questions, please call 1-800-444-3353.  
Page 4  
 
PARTS LIST  
No# Description  
QTY  
4
2
2
2
2
2
2
2
1
2
3
4
5
6
7
8
9
Corner Support  
Casters Bracket  
Pad Bracket  
Pad Knob  
Pad Cover  
Plastic Pad  
2" Swivel Caster  
3"Wheel  
Screw Bolt  
2
10 Rivet  
2
11 Hex Head Screw M8 x 50  
12 Hex Head Bolt M8 x 55  
13 Flash Washer M8  
14 Wing Nut 1/2"  
16  
4
2
2
15 Hex Nut 3/8” - 16NC  
16 Nylon Lock Nut M8  
4
20  
DIAGRAM  
PLEASE READ CAREFULLY  
The Manufacturer and/or Distributor have provided the Parts Breakdown and Assembly Diagram  
in this Manual as a reference tool only. This Tool is not meant be disassembled by anyone other  
than a QUALIFIED REPAIR FACILITY. Neither the Manufacturer and/or the Distributor make any  
representation or warranty of any kind to the Buyer that He or She are qualified to make any  
repairs to the product represented in this Manual. In fact, the Manufacturer and /or the Distributor  
expressly states that all repairs and parts replacement should be undertaken by CERTIFIED AND  
LICENSEDTECHNICIANS, and NOT by the Buyer.The Buyer assumes all risk and liability arising  
out of His or Her repairs to the original product or the replacement parts thereto, or arising out of  
His or Her installation of replacement parts thereto.  
SKU 95288  
For technical questions, please call 1-800-444-3353.  
Page 5  
 
WARRANTY  
LIMITED 90 DAY WARRANTY  
Harbor FreightTools Co.makes every effort to assure that its products meet high quality and durability standards,  
and warrants to the original purchaser that this product is free from defects in materials and workmanship for  
the period of ninety days from the date of purchase. This warranty does not apply to damage due directly or  
indirectly, to misuse, abuse, negligence or accidents, repairs or alterations outside our facilities, or to lack of  
maintenance.We shall in no event be liable for death, injuries to persons or property, or for incidental, contingent,  
special or consequential damages arising from the use of our product. Some states do not allow the exclusion or  
limitation of incidental or consequential damages, so the above limitation of exclusion may not apply to you.THIS  
WARRANTY IS EXPRESSLY IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING  
THE WARRANTIES OF MERCHANTABILITY AND FITNESS.  
To take advantage of this warranty, the product or part must be returned to us with transportation charges prepaid.  
Proof of purchase date and an explanation of the complaint must accompany the merchandise. If our inspection  
verifies the defect, we will either repair or replace the product at our election or we may elect to refund the purchase  
price if we cannot readily and quickly provide you with a replacement. We will return repaired products at our  
expense, but if we determine there is no defect, or that the defect resulted from causes not within the scope of  
our warranty, then you must bear the cost of returning the product.  
This warranty gives you specific legal rights and you may also have other rights which vary from state to state.  
3491 Mission Oaks Blvd. • PO Box 6009 • Camarillo, CA 93011 • (800) 444-3353  
SKU 95288  
For technical questions, please call 1-800-444-3353.  
Page 6  
 

Grizzly Impact Driver H0582 User Manual
Grizzly Planer G0526 User Manual
Grizzly Sander G1173 User Manual
H2O Audio Headphones iDV1 5A1 User Manual
Honeywell Laptop 99EXL0X XXXXXXXI User Manual
HP Hewlett Packard Speaker System 8900D User Manual
Hubbell Lawn Mower K 18 User Manual
Husqvarna Chainsaw 1018855 26 User Manual
Hypercom Network Router IEN 500 User Manual
Hyundai Food Warmer I10 User Manual