Harbor Freight Tools Door 97004 User Manual

wireless doorbell  
Model 97004  
set up And operAting instructions  
Diagrams within this manual may not be drawn proportionally.  
Due to continuing improvements, actual product may differ slightly from the product described herein.  
®
distributed exclusively by Harbor Freight tools .  
3491 Mission Oaks Blvd., Camarillo, CA 93011  
Visit our website at: http://www.harborfreight.com  
read this material before using this product.  
Failure to do so can result in serious injury.  
sAVe tHis MAnuAl.  
©
®
Copyright 2007 by Harbor Freight Tools . All rights reserved. No portion of  
this manual or any artwork contained herein may be reproduced in any shape  
or form without the express written consent of Harbor Freight Tools.  
For technical questions or replacement parts, please call 1-800-444-3353.  
 
generAl sAFetY rules  
wArning! read all instructions  
Failure to follow all instructions listed below may result in electric shock,  
fire, and/or serious injury.  
sAVe tHese instructions  
1.  
2.  
work area safety  
a. Keep work area clean and well lit. Cluttered or dark areas invite accidents.  
b. Keep children and bystanders away while installing the wireless  
doorbell. Distractions can cause you to lose control.  
personal safety  
a. Stay alert, watch what you are doing and use common sense when installing  
the Wireless Doorbell.  
b. Use safety equipment. Always wear eye protection. Safety equipment such  
as hearing protection used for appropriate conditions will reduce personal  
injuries.  
c. Store idle tools out of the reach of children and do not allow persons  
unfamiliar with the Wireless Doorbell or these instructions to operate the  
Wireless Doorbell.  
d. Maintain the Wireless Doorbell. Check for breakage of parts and any other  
condition that may affect the Wireless Doorbell operation. If damaged, have  
the Wireless Doorbell repaired before use. Many accidents are caused by  
poorly maintained products.  
e. Use the Wireless Doorbell and accessories, in accordance with these  
instructions and in the manner intended for this particular type of product.  
Use of the Wireless Doorbell for operations different from those intended  
could result in a hazardous situation.  
speciFic sAFetY rules  
1.  
Maintain labels and nameplates on the tool. These carry important safety  
information. If unreadable or missing, contact Harbor Freight Tools for a  
replacement.  
2.  
3.  
4.  
This product is not a toy. Keep it out of reach of children.  
Do not get the Wireless Doorbell wet as this will damage the unit.  
The warnings, precautions, and instructions discussed in this instruction manual  
cannot cover all possible conditions and situations that may occur. It must be  
understood by the operator that common sense and caution are factors which  
cannot be built into this product, but must be supplied by the operator.  
SKU 97004  
For technical questions, please call 1-800-444-3353.  
Page 3  
 
sAVe tHese instructions.  
speciFicAtions  
Polystyrene transmitter and receiver,  
Construction  
steel mounting hardware and  
thermoplastic anchors  
(1) VA23A, MS21/MN21, A23S, 12V,  
Alkaline (included)  
Transmitter Battery  
Receiver Battery  
Working Distance  
(2) AA, 1.5V (not included)  
Up to 200 Feet  
unpAcKing  
When unpacking, check to make sure that the item is intact and undamaged. If  
any parts are missing or broken, please call Harbor Freight Tools at the number shown  
on the cover of this manual as soon as possible.  
set up instructions  
read the entire iMportAnt sAFetY inForMAtion section at the  
beginning of this manual including all text under subheadings therein  
before set up or use of this product.  
risk of accidental starting; resulting in serious personal  
injury. turn the power switch of the tool to its “oFF”  
position and unplug the tool from its electrical outlet before  
assembling or making any adjustments to the tool.  
wArning  
note: For additional information regarding the parts listed in the following pages, refer  
to the Assembly Diagram near the end of this manual.  
SKU 97004  
For technical questions, please call 1-800-444-3353.  
Page 4  
 
Assembly  
installing and replacing batteries  
Figure 1  
Receiver Battery  
Compartment  
Battery Cover  
(3)  
1.  
2.  
You will have to install 2 “AA” Batteries in the Receiver (2). Remove the Battery  
Cover (3) located on the back of the Receiver (2)-see Figure 1.  
Insert Batteries making certain that the polarity lines up with the polarity  
indicated in the Battery Compartment. Replace Battery Cover (3).  
Figure 2  
Transmitter Battery  
Cover (4)  
Transmitter (1)  
3.  
4.  
5.  
To replace Transmitter Battery, first remove the Screw (9) holding the Battery  
Cover (4) on. Remove the Battery Cover by pulling it up and off.  
Replace the Battery in the Battery Compartment so that the battery’s polarity  
lines up with that indicated-see Figure 2.  
Replace Screw (9) to hold the Battery Cover (4) on.  
Mounting  
1.  
Note that the Transmitter (1) and the Receiver (2) must be mounted within 200  
Feet of each other.  
SKU 97004  
For technical questions, please call 1-800-444-3353.  
Page 5  
 
2.  
3.  
The Wireless Doorbell can be mounted with two-sided Mounting Tape (5/ꢀ).  
Remove backing from the Mounting Tape (5/ꢀ). Attach the backing to the  
Transmitter and/or Receiver and press it into place. Make certain that the  
mounting surface is dry and free of debris. Remove the backing from the  
second side of the Tape and press the unit onto the desired location.  
Two Mounting Screws (8) and Anchors (7) are included to secure the  
Transmitter to walls. Before inserting Mounting Screws (8) with Anchors (7) into  
any surface, make certain that the drilling path is clear of wiring. Drill holes for  
Anchors. Insert Anchors (7) and thread in Mounting Screws (8).  
Functions  
1.  
Push button on Transmitter to cause Receiver to emit ringing tone.  
pleAse reAd tHe Following cAreFullY  
THe MANUFACTUReR AND/OR DISTRIBUTOR HAS PROVIDeD THe PARTS lIST AND  
ASSeMBlY DIAgRAM IN THIS MANUAl AS A ReFeReNCe TOOl ONlY. NeITHeR THe  
MANUFACTUReR OR DISTRIBUTOR MAKeS ANY RePReSeNTATION OR WARRANTY OF  
ANY KIND TO THe BUYeR THAT He OR SHe IS qUAlIFIeD TO MAKe ANY RePAIRS TO  
THe PRODUCT, OR THAT He OR SHe IS qUAlIFIeD TO RePlACe ANY PARTS OF THe  
PRODUCT. IN FACT, THe MANUFACTUReR AND/OR DISTRIBUTOR exPReSSlY STATeS  
THAT All RePAIRS AND PARTS RePlACeMeNTS SHOUlD Be UNDeRTAKeN BY CeRTIFIeD  
AND lICeNSeD TeCHNICIANS, AND NOT BY THe BUYeR. THe BUYeR ASSUMeS All RISK  
AND lIABIlITY ARISINg OUT OF HIS OR HeR RePAIRS TO THe ORIgINAl PRODUCT OR  
RePlACeMeNT PARTS THeReTO, OR ARISINg OUT OF HIS OR HeR INSTAllATION OF  
RePlACeMeNT PARTS THeReTO.  
pArts list  
part  
description  
Transmitter  
Q’ty  
part  
description  
larger Mounting Tape  
Anchors  
Q’ty  
1
2
3
4
5
1
1
1
1
1
7
8
9
1
2
2
1
Receiver  
Receiver Battery Cover  
Transmitter Battery Cover  
Small Mounting Tape  
Screws  
Battery Cover Screw  
SKU 97004  
For technical questions, please call 1-800-444-3353.  
Page ꢀ  
 
AsseMblY diAgrAM  
2
4
5
1
3
7
9
8
Record products serial number Here:  
note: If product has no serial number, record month and year of purchase instead.  
note: Some parts are listed and shown for illustration purposes only, and are not  
available individually as replacement parts.  
SKU 97004  
For technical questions, please call 1-800-444-3353.  
Page 7  
 

Harman Kardon Stereo Receiver AVR 1565 User Manual
HP Hewlett Packard Switch 1410 16G User Manual
HTC Cell Phone HS S200 User Manual
HTC PDAs Smartphones HTC P4350 User Manual
Hustler Turf Lawn Mower Diesel Z User Manual
Hustler Turf Lawn Mower M 1 User Manual
Icom Two Way Radio IC F4TR User Manual
IKEA Plumbing Product AA 290704 1 User Manual
Ikelite Camera Accessories 624088 User Manual
IMC Networks Switch AccessEtherLinx 4 User Manual