sPEcIFIcATIONs
Weight Capacity
150 lb.
For LED / LCD / Plasma TVs 37” to 61” wide
FLAT PANEL TV
WALL MOUNT
UNPAckINg
When unpacking, make sure that the item is
intact and undamaged. If any parts are missing or
broken, please call Harbor Freight Tools at
1-800-444-3353 as soon as possible.
Model 67781
INsTrUcTIONs ANd PrEcAUTIONs
IMPOrTANT sAFETY INFOrMATION
1.
Do not exceed 150 lb. max. weight capacity of
TV Bracket. Sudden load movement may briefly
create excess load causing product failure.
2.
Do not mount TV Bracket to hollow wall, gypsum
board, or similar material that will not support the
weight of the TV. Mount only to 2” x 4” wood stud
or concrete/brick walls that can safely support
combined weight of Bracket, TV and all attached
hardware and components.
3.
If you are unsure wall is strong enough to
support weight of TV and TV Bracket, contact a
professional installer to reinforce wall.
4.
5.
Do not mount overhead.
Assemble and install only according to these
instructions. Improper assembly and installation
can create hazards and lead to personal injury
and property damage.
6.
7.
8.
9.
Verify that mounting surface has no hidden utility
lines before drilling or driving screws.
Wear ANSI-approved safety goggles and heavy-
duty work gloves during installation.
sAVE ThEsE
INsTrUcTIONs.
rEAd ALL
Inspect before installing; do not mount to wall if
parts are missing, loose or damaged.
Use as intended only. Do not use TV Bracket for
any purpose for which it was not designed.
PrEcAUTIONs ANd
INsTrUcTIONs.
10. Keep installation area clean and well lit.
11. Do not assemble or install when tired or when
©
®
Copyright 2010 by Harbor Freight Tools . All rights
reserved. No portion of this document or any artwork
contained herein may be reproduced in any shape or form
without the express written consent of Harbor Freight
Tools. Diagrams within this document may not be drawn
proportionally. Due to continuing improvements, actual
product may differ slightly from the product described herein.
Tools required for assembly and service may not be included.
under the influence of drugs or medication.
12. This product is not a toy. Do not allow children to
play with or near this item.
13. Maintain product labels and nameplates. These
carry important safety information. If unreadable
or missing, contact Harbor Freight Tools for a
replacement.
For technical questions or replacement parts,
please call 1-800-444-3353.
2.
WArNINg! Do no lay flat panel TV face down;
cover its surface with a towel or other soft
material and tilt it against the wall or another solid
surface.
7.
Tighten the two clamping screws leaving about
an eight of an inch space. See Figure 6.
3.
4.
WArNINg! Some Flat Panel TVs are heavy; two
people may be needed to lift and support the TV
while it is being attached to the TV Bracket.
Locate the mounting holes on back of TV and
select mounting Screws (3-6) that fit properly.
NOTE: If you do not find the appropriate-sized
Screws, refer to TV owners manual or contact TV
manufacturer. Thread the Screws (3, 4, 5 or 6)
through the Square Pads (8), the Support Arms
(2), Spacers (7) and into the mounting holes in
the back of TV panel. See Figure 4, below.
Screws (3-6)
Clamping
Screw
Square Pad (8)
Spacer (7)
Figure 6
Support
Arms (2)
8.
To adjust the TV angle, back off the two nuts at
the Support Arm hinges by one turn. Back off
the two angle-adjusting screws located at the
sides of the Support Arms until end of the screw
threads are almost flush with the other side of the
Support Arms. See Figure 7.
TV Panel
Figure 4
5.
6.
NOTE: The wide part of the Spacers rest against
the Support Arms.
Carry TV to mounted Bracket and lower onto
Cross Bars, making sure the four tabs of the
mounts are hooked onto the top of Cross Bars
and that TV is centered. See Figure 5.
Angle Adjusting
Screw
Angle Adjusting
Screw
Cross Bars
Figure 7
9.
cAUTION: Make sure that the end of the screws
does not come out of the Support Arms.
10. Tilt the TV to the desired angle (four approximate
adjustment positions = 0°, 3°, 7° and 12°).
Tighten the Angle-adjusting screws all the way to
lock the angle position.
Figure 5
SKU 67781
For technical questions, please call 1-800-444-3353.
Page 3
PArTs LIsT & AssEMbLY dIAgrAM
Part
1
description
Wall Bracket
Qty.
1
2
Support Arm
2
3
4
5
6
Screw (M4 x .7 x 35mm)
Screw (M5 x .8 x 35mm)
Screw (M6 x 1.0 x 35mm)
Screw (M6 x 1.25 x 35mm)
Spacer
4
4
4
4
7
4
8
Square Pad
4
9
Washer
4
10
11
Lag Bolt
Wall Anchor
4
4
2
1
6
5
3
4
8
10
7
9
11
record serial Number here:
Note:If product has no serial number, record month and year of purchase instead.
Note:Some parts are listed and shown for illustration purposes only, and are not available individually as
replacement parts.
PLEAsE rEAd ThE FOLLOWINg cArEFULLY
THE MANUFACTUrEr AND/Or DISTrIBUTOr HAS PrOVIDED THE PArTS LIST AND ASSEMBLy DIAgrAM IN THIS DOCUMENT AS
A rEFErENCE TOOL ONLy. NEITHEr THE MANUFACTUrEr Or DISTrIBUTOr MAKES ANy rEPrESENTATION Or WArrANTy
OF ANy KIND TO THE BUyEr THAT HE Or SHE IS qUALIFIED TO MAKE ANy rEPAIrS TO THE PrODUCT, Or THAT HE Or SHE
IS qUALIFIED TO rEPLACE ANy PArTS OF THE PrODUCT. IN FACT, THE MANUFACTUrEr AND/Or DISTrIBUTOr ExPrESSLy
STATES THAT ALL rEPAIrS AND PArTS rEPLACEMENTS SHOULD BE UNDErTAKEN By CErTIFIED AND LICENSED TECHNICIANS,
AND NOT By THE BUyEr. THE BUyEr ASSUMES ALL rISK AND LIABILITy ArISINg OUT OF HIS Or HEr rEPAIrS TO THE
OrIgINAL PrODUCT Or rEPLACEMENT PArTS THErETO, Or ArISINg OUT OF HIS Or HEr INSTALLATION OF rEPLACEMENT
PArTS THErETO.
SKU 67781
For technical questions, please call 1-800-444-3353.
Page 4
|