Pet hair cliPPer
Model 96822
cleaning and OPeratiOn instructiOns
Diagrams within this manual may not be drawn proportionally.
Due to continuing improvements, actual product may differ slightly from the product described herein.
®
distributed exclusively by harbor Freight tools .
3491 Mission Oaks Blvd., Camarillo, CA 93011
Visit our website at: http://www.harborfreight.com
read this material before using this product.
Failure to do so can result in serious injury.
saVe this Manual.
©
®
Copyright 2007 by Harbor Freight Tools . All rights reserved. No portion of this
manual or any artwork contained herein may be reproduced in any shape or form
without the express written consent of Harbor Freight Tools.
For technical questions or replacement parts, please call 1-800-444-3353.
2.
3.
Unplug from outlet when not in use and before maintenance or cleaning.
Do not operate any appliance with a damaged cord or plug or after the appliance malfunctions or
has been damaged in any manner. Return appliance to the nearest authorized service facility for
examination, repair, or adjustment.
4.
ꢀ.
This appliance has a polarized plug (one blade is wider than the other). To reduce the risk of
electric shock, this plug is intended to fit into a polarized outlet only one way. If the plug does not
fit fully in the outlet, reverse the plug. If it still does not fit, contact a qualified electrician. Do not
change the plug in any way.
Do not use this product in a damp or wet location.
Power cord safety
1.
A short power supply cord is to be provided to reduce risks resulting from becoming entangled in or
tripping over a longer cord.
2.
Longer extension cords are available and may be used if care is exercised in their use.
If a long extension cord is used,
3.
a. The marked electrical rating of the (detachable power supply cord or) extension cord should
be at least as great as the electrical rating of the appliance,
b. If the appliance is of the grounded type, the extension cord should be a grounding type 3-wire
cord, and
c. The longer cord should be arranged so that it will not drape over the counter top or tabletop
where it can be pulled on by children or tripped over.
general safety
1.
2.
The use of accessory attachments not recommended by the appliance manufacturer may cause
injuries. Never use attachments from other clipper sets with this product.
Plug cord into the wall outlet. To disconnect, turn the power switch to “off”, then remove plug from
wall outlet.
3.
4.
Do not use appliance for other than intended use.
Maintain labels and nameplates on the appliance. These carry important safety information. If
unreadable or missing, contact Harbor Freight Tools for a replacement.
ꢀ.
6.
This product is not a toy. Keep it out of reach of children.
The warnings, precautions, and instructions discussed in this instruction manual cannot cover
all possible conditions and situations that may occur. It must be understood by the operator
that common sense and caution are factors which cannot be built into this product, but must be
supplied by the operator.
saVe these instructiOns.
SKU 96822
For technical questions, please call 1-800-444-3353.
Page 3
sPeciFicatiOns
Electrical Requirements
120 V~ / 60 Hz / 8 W
Pet Hair Trimmer
Scissors
Accessories
Cleaning Brush
Blade Oil (Plastic Bottle)
Comb Attachments
Right Ear Taper
Left Ear Taper
No. 1: 1/8” (.3 cm) Cut
No. 2: 1/4” (.6 cm) Cut
No. 3: 3/8” (.9 cm) Cut
No. 4: 1/2” (1.3 cm) Cut
Comb Attachments
hOusehOld use OnlY
unPacking
When unpacking, check to make sure that the item is intact and undamaged. If any parts are
missing or broken, please call Harbor Freight Tools at the number shown on the cover of this manual as
soon as possible.
cleaning
read the entire iMPOrtant saFeguards section at the beginning of this manual
including all text under subheadings therein before set up or use of this product.
risk OF shOck!
Warning
Before cleaning appliance, make sure the appliance’s switch is turned off,
the cord is unplugged, and the unit has cooled completely.
do not immerse motor/heating element, cord, or plug in water or any
other liquid.
1.
2.
Remove cover and gently remove hair particles with the included cleaning brush or compressed
air.
Wipe exterior of Clipper with a moist, soft cloth and store product out of the reach of children.
asseMBlY & OPeratiOn
read the entire iMPOrtant saFeguards section at the beginning of this manual
including all text under subheadings therein before set up or use of this product.
Before appliance assembly or adjustment, make sure the appliance’s
Warning
switch is turned off, the cord is unplugged, and the unit has cooled
completely.
note: For additional information regarding the parts listed in the following pages, refer to the Assembly
Diagram near the end of this manual.
SKU 96822
For technical questions, please call 1-800-444-3353.
Page 4
Note: When mounting the blades, always wear work gloves.
1.
2.
3.
Untwist the power cord to avoid tangling.
Remove Blade Cover (1).
Choose Comb (2-7) as appropriate to the clipping task at hand, and clip it onto the Clipper over
top of the blades.
4.
The Blade Lever (ꢀ0) allows the operator to change the closeness setting of the cut without an
additional attachment comb. At the top position, the blades will give the closest cut and leave
the hair the shortest. Pushing the lever downward increases the cutting length. If hair jams
the blades, switch the Blade Lever up and down rapidly to clear the blades. Before turning
the Clipper off, rapidly move the Blade Lever from close cut to longer cut twice. This will clear
trimmings from the Clipper.
ꢀ.
6.
Make sure Sliding Switch (4ꢀ) is in OFF position prior to plugging the Clipper into an electrical
outlet.
Plug the Clipper into any standard 120V electrical outlet, and push the Switch Cover (4ꢀ) forward
to turn the unit on.
7.
8.
Clean, brush, and dry the pet thoroughly before clipping or trimming.
To prevent accidents, turn off the appliance and disconnect its power supply after use. Inspect
the Clipper, making sure it is free of hair, oil, or debris between the cutting blade teeth. Lubricate
using the provided clipper oil. Turn the unit on to distribute the oil and to make sure it runs
smoothly. Wipe off any excess oil. This should be done after each use. Clean, lubricate replace
Blade Cover (1) and then store the appliance indoors out of the reach of children.
insPectiOn and Maintenance
Before appliance inspection or maintenance, make sure the appliance’s
Warning
switch is turned off, the cord is unplugged, and the unit has cooled
completely.
do not use damaged appliances. if abnormal noise or vibration occurs,
have the problem corrected before further use.
1.
2.
BeFOre each use, inspect the general condition of the appliance. Check for loose screws,
misalignment or binding of moving parts, cracked or broken parts, damaged electrical wiring, and
any other condition that may affect its safe operation.
Blades should be oiled with the provided clipper oil every few haircuts to maintain the Clipper
in peak condition. Do not use hair oil, grease, or any solvent on the Clipper. The solvent will
evaporate and leave a residue that can slow down the blade’s motion.
Blade alignment
1.
2.
3.
The Clipper comes oiled and aligned from the factory. Blades must be realigned after they have
been removed for cleaning or replacement.
To realign blades, match the upper and lower blades teeth up, point for point. The end of the top
blade teeth should be approximately 1.2mm (just under 1/16”) back from the bottom blade.
If blade alignment is incorrect: add a few drops of oil to the blades, turn the Clipper on for a few
moments, then turn off and unplug.
SKU 96822
For technical questions, please call 1-800-444-3353.
Page ꢀ
4.
ꢀ.
Loosen screws slightly and readjust.
Tighten screws after blade is aligned.
SKU 96822
For technical questions, please call 1-800-444-3353.
Page 6
Please read the FOllOWing careFullY
The ManufaCTurer anD/Or DISTrIBuTOr haS PrOvIDeD The ParTS LIST anD aSSeMBLy
DIagraM In ThIS ManuaL aS a referenCe TOOL OnLy. neITher The ManufaCTurer Or
DISTrIBuTOr MakeS any rePreSenTaTIOn Or WarranTy Of any kInD TO The Buyer ThaT
he Or She IS quaLIfIeD TO Make any rePaIrS TO The PrODuCT, Or ThaT he Or She IS
quaLIfIeD TO rePLaCe any ParTS Of The PrODuCT. In faCT, The ManufaCTurer anD/Or
DISTrIBuTOr exPreSSLy STaTeS ThaT aLL rePaIrS anD ParTS rePLaCeMenTS ShOuLD Be
unDerTaken By CerTIfIeDanD LICenSeD TeChnICIanS, anD nOT By The Buyer. The Buyer
aSSuMeS aLL rISk anD LIaBILITy arISIng OuT Of hIS Or her rePaIrS TO The OrIgInaL
PrODuCT Or rePLaCeMenT ParTS ThereTO, Or arISIng OuT Of hIS Or her InSTaLLaTIOn
OF REPLACEMENT PARTS THERETO.
Parts list
Part
1
description
Blade Cover
Qty
1
1
1
1
1
1
1
2
1
1
1
1
1
1
2
1
1
1
2
1
1
1
1
1
1
1
1
1
2
Part
30
31
32
33
34
3ꢀ
36
37
38
39
40
41
42
43
44
4ꢀ
46
47
48
49
ꢀ0
ꢀ1
ꢀ2
ꢀ3
ꢀ4
ꢀꢀ
ꢀ6
ꢀ7
description
Orange Inner Wire Lead
Black Inner Wire Lead
Heat Shrink Tube
Heat Shrink Tube
Power Wire
Qty
1
1
1
2
1
1
1
1
4
1
1
1
2
1
1
1
6
1
1
2
1
1
1
2
1
1
1
1
2
Comb #1
3
Comb #2
4
Comb #3
ꢀ
Comb #4
6
Left Comb
Wire Clamp
7
Right Comb
Screw
Wire Protection
Switch
8
9
Fixed Blade
Blade Holder
Movable Blade
Movable Spring
Movable Blade Spring
Movable Blade Holder
Screw
Screw
10
11
12
13
14
1ꢀ
16
17
18
19
20
21
22
23
24
2ꢀ
26
27
28
29
Tri-Bar
Brown Paper
Gummed Paper
Screw
Filament Plate
Screw
Oscillating Lever
Axis Cover
Sliding Switch
Insert
Resist Ring
Spring
Lower Cover
Location Column
Shockproof Gasket
Blade Lever
Holder
Upper Cover
Iron Sheet
Screw
Magnet
Plug
Hold Frame Cover
Hold Frame
T Fixture
Screw
Sponge
Clipper Oil (not shown)
Scissors (not shown)
Cleaning Brush (not shown)
Lacquered Wire
Loop Holder
Yellow Wax Tube
SKU 96822
For technical questions, please call 1-800-444-3353.
Page 7
asseMBlY diagraM
record Product’s serial number here:
note: If product has no serial number, record month and year of purchase instead.
note: Some parts are listed and shown for illustration purposes only, and are not avail-
able individually as replacement parts.
SKU 96822
For technical questions, please call 1-800-444-3353.
Page 8
|