½” ELECTRIC IMPACT WRENCH
Model 31877
SET uP ANd OPERATINg INSTRuCTIONS
Diagrams within this manual may not be drawn proportionally.
Due to continuing improvements, actual product may differ slightly from the product described herein.
®
distributed exclusively by Harbor Freight Tools .
3491 Mission Oaks Blvd., Camarillo, CA 93011
Read this material before using this product.
Failure to do so can result in serious injury.
SAVE THIS MANuAL.
©
®
Copyright 1997 by Harbor Freight Tools . All rights reserved. No portion of this
manual or any artwork contained herein may be reproduced in any shape or form
without the express written consent of Harbor Freight Tools.
For technical questions or replacement parts, please call 1-800-444-3353.
Manual Revised 07i
gENERAL SAFETY RuLES
WARNINg! Read all instructions
Failure to follow all instructions listed below may result in electric shock,
fire, and/or serious injury. The term “power tool” in all of the warnings listed
below refers to your line-operated (corded) power tool or battery-operated
(cordless) power tool.
SAVE THESE INSTRuCTIONS
1.
ꢀ.
KEEP WORK AREA CLEAN. Cluttered areas invite injuries.
OBSERVE WORK AREA CONDITIONS. Do not use machines or power tools in damp,
wet, or poorly lit locations. Don’t expose to rain. Keep work area well lit. Do not use elec-
trically powered tools in the presence of flammable gases or liquids.
3.
4.
ꢁ.
KEEP CHILDREN AWAY. Children must never be allowed in the work area. Do not let
them handle machines, tools, or extension cords.
STORE IDLE EQUIPMENT. When not in use, tools must be locked up in a dry location to
inhibit rust. Always lock up tools and keep out of reach of children.
DO NOT FORCE THE TOOL. It will do the job better and more safely at the rate for
which it was intended. Do not use inappropriate attachments in an attempt to exceed the
tool’s capacities.
ꢂ.
7.
8.
USE THE RIGHT TOOL FOR THE JOB. Do not attempt to force a small tool or attach-
ment to do the work of a larger industrial tool. Do not use a tool for a purpose for which it
was not intended.
DRESS PROPERLY. Do not wear loose clothing or jewelry as they can be caught in
moving parts. Protective, electrically non-conductive clothes and non-skid footwear are
recommended when working. Wear restrictive hair covering to contain long hair.
USE EYE AND EAR PROTECTION. Always wear ANSI-approved chemical splash gog-
gles when working with chemicals. Always wear ANSI-approved impact safety goggles
at other times. Wear a full face shield if you are producing metal filings or wood chips.
Wear and ANSI approved dust mask or respirator when working around metal, wood,
and chemical dusts and mists.
9.
DO NOT ABUSE THE POWER CORD. Do not yank it to disconnect it from the recep-
tacle. Do not carry tools by the cord.
10.
11.
DO NOT OVERREACH. Keep proper footing and balance at all times. Do not reach over
or across running machines.
MAINTAIN TOOLS WITH CARE. Keep tools sharp and clean for better and safer perfor-
mance. Follow instructions for lubricating and changing accessories. Inspect tool cords c
and, if damaged, have them repaired by an authorized technician. The handles must be
kept clean, dry, and free from oil and grease at all times.
1ꢀ.
DISCONNECT POWER. Unplug when not in use, before servicing, and when changing
accessories.
SKU 31877
For technical questions, please call 1-800-444-3353.
Page 3
13.
14.
1ꢁ.
REMOVE ADJUSTING KEYS AND WRENCHES. Make it a habit to check that keys and
adjusting wrenches are removed from the tool or machine work surface before plugging
it in.
AVOID UNINTENTIONAL STARTING. Be sure the switch is in the OFF position when
not in use and before plugging in. Do not carry any tool with your finger on the trigger,
whether it is plugged in or not.
OUTDOOR EXTENSIONS CORDS. When the equipment is operated outdoors, use
only extension cords intended or outside use. See chart under “Extension Cords: for the
proper AWG rating depending on the length of the cord(s) being used.
1ꢂ.
17.
STAY ALERT. Watch what you are doing, use common sense. Do not operate any tool
when you are tired.
CHECK DAMAGED PARTS. Before using any tool, any part that appears damaged
should be carefully checked to determine that it will operate properly and perform its
intended function. Check for alignment and binding of moving parts; any broken parts or
mounting fixtures; and any other condition that may affect proper operation. Any part that
is damaged should be properly repaired or replaced by a qualified technician. Do not use
the tool if any switch does not turn on and off properly.
18.
19.
GUARD AGAINST ELECTRIC SHOCK. Prevent body contact with grounded surfaces
such as pipes, radiators, ranges, and refrigerator enclosures.
REPLACEMENT PARTS AND ACCESSORIES. When servicing, use only identical
replacement parts. Use of any other parts will void the warranty. Only use accessories
intended for use with this tool. Approved accessories are available from Harbor Freight
Tools.
ꢀ0.
ꢀ1.
ꢀꢀ.
DO NOT OPERATE TOOL IF UNDER THE INFLUENCE OF ALCOHOL OR DRUGS.
Read warning labels on prescriptions to determine if your judgment or reflexes are im-
paired while taking drugs. If there is any doubt, do not operate the tool.
ONLY USE IMPACT SOCKETS. Sockets built for impact wrenches are specifically de-
signed to withstand the force of the delivered blow. Any other socket may shatter, caus-
ing injury to the operator and damage to any nearby equipment.
People with pacemakers should consult their physician(s) before use. Electromagnetic
fields in close proximity to heart pacemaker could cause pacemaker interference or
pacemaker failure. In addition, people with pacemakers should:
• Avoid operating alone.
• Do not use with power switch locked on.
• Properly maintain and inspect to avoid electrical shock.
• Any power cord must be properly grounded. Ground Fault Circuit Interrupter (GFCI)
should also be implemented – it prevents sustained electrical shock.
ꢀ3.
Some dust created by power sanding, sawing, grinding, drilling, and other construction
activities, contains chemicals known [to the State of California] to cause cancer, birth
defects or other reproductive harm. Some examples of these chemicals are:
Lead from lead-based paints
Crystalline silica from bricks and cement or other masonry products
SKU 31877
For technical questions, please call 1-800-444-3353.
Page 4
Arsenic and chromium from chemically treated lumber
Your risk from these exposures varies, depending on how often you do this type of work.
To reduce your exposure to these chemicals: work in a well ventilated area, and work
with approved safety equipment, such as those dust masks that are specially designed
to filter out microscopic particles. (California Health & Safety Code § 25249.5, et seq.)
ꢀ4.
The warnings, precautions, and instructions discussed in this instruction manual cannot
cover all possible conditions and situations that may occur. It must be understood by
the operator that common sense and caution are factors which cannot be built into this
product, but must be supplied by the operator.
SAVE THESE INSTRuCTIONS.
gROuNdINg
Improperly connecting the grounding wire can result in electric
shock.
WARNINg
Check with a qualified electrician if you are in doubt as to whether
the outlet is properly grounded. do not modify the power cord
plug provided with the tool. do not use the tool if the power cord
or plug is damaged. If damaged, have it repaired by a service
facility before use. If the plug will not fit the outlet, have a proper
outlet installed by a qualified electrician.
double Insulated Tools: Tools with Two Prong Plugs
1.
ꢀ.
Tools marked “Double Insulated” do not require
grounding. They have a special double insula-
tion system which satisfies OSHA requirements
and complies with the applicable standards of
Underwriters Laboratories, Inc., the Canadian
Standard Association, and the National Electrical
Code. (See Outlets for 2-Prong Plug.)
Double insulated tools may be used in either of
the 1ꢀ0 volt outlets shown in the illustration to
the right. (See Outlets for 2-Prong Plug.)
Outlets for 2-Prong Plug
Extension Cords
1.
ꢀ.
Grounded tools require a three wire extension cord. Double insulated tools can use
either a two or three wire extension cord.
As the distance from the supply outlet increases, you must use a heavier gauge exten-
sion cord. Using extension cords with inadequately sized wire causes a serious drop in
voltage, resulting in loss of power and possible tool damage.
(See Table A.)
SKU 31877
For technical questions, please call 1-800-444-3353.
Page ꢁ
3.
The smaller the gauge number of the wire, the greater the capacity of the cord. For ex-
ample, a 14 gauge cord can carry a higher current than a 1ꢂ gauge cord.
(See Table A.)
4.
ꢁ.
When using more than one extension cord to make up the total length, make sure each
cord contains at least the minimum wire size required. (See Table A.)
If you are using one extension cord for more than one tool, add the nameplate amperes
and use the sum to determine the required minimum cord size.
(See Table A.)
ꢂ.
7.
If you are using an extension cord outdoors, make sure it is marked with the suffix “W-A”
(“W” in Canada) to indicate it is acceptable for outdoor use.
Make sure the extension cord is properly wired and in good electrical condition. Always
replace a damaged extension cord or have it repaired by a qualified electrician before
using it.
8.
Protect the extension cords from sharp objects, excessive heat, and damp or wet areas.
RECOMMENdEd MINIMuM WIRE gAugE FOR EXTENSION CORdS* (120/240 VOLT)
NAMEPLATE
EXTENSION CORd LENgTH
AMPERES
(at full load)
25 Feet
50 Feet
75 Feet
100 Feet
150 Feet
0 – ꢀ.0
ꢀ.1 – 3.4
18
18
18
18
18
14
1ꢀ
18
18
18
1ꢂ
14
1ꢀ
10
18
18
1ꢂ
14
1ꢀ
10
-
18
1ꢂ
14
1ꢀ
10
-
1ꢂ
14
1ꢀ
1ꢀ
-
3.ꢁ – ꢁ.0
ꢁ.1 – 7.0
7.1 – 1ꢀ.0
1ꢀ.1 – 1ꢂ.0
1ꢂ.1 – ꢀ0.0
TABLE A
-
-
-
* Based on limiting the line voltage drop to five volts at 150% of the rated amperes.
Symbology
Double Insulated
Volts Alternating Current
Amperes
V~
A
Canadian Standards Association
No Load Revolutions per Minute
(RPM)
Underwriters Laboratories, Inc.
n xxxx/min.
0
SKU 31877
For technical questions, please call 1-800-444-3353.
Page ꢂ
SPECIFICATIONS
Motor
Power
Drive
1ꢀ0 V~, ꢂ0 Hz, 7 A; ꢀ100 RPM
2400 BPM: 240 ft-lb Torque
1/ꢀ”
230373
uNPACkINg
When unpacking, check to make sure that the item is intact and undamaged. If any
parts are missing or broken, please call Harbor Freight Tools at the number shown on the cover
of this manual as soon as possible.
OPERATINg INSTRuCTIONS
Read the ENTIRE IMPORTANT SAFETY INFORMATION section at the beginning
of this manual including all text under subheadings therein before set up or use
of this product.
general guidelines
Anvil
(# 1ꢂ)
1.
ꢀ.
Use sockets designed for impact wrench use.
Do not use sockets with drives smaller than
1
/ ”. You may use impact socket adapters to
ꢀ
use impact sockets with drives greater than
1
/ ”.
ꢀ
3.
4.
Only use socket extensions designed for
impact use.
Pressing the top of the ROCKER SWITCH
(ꢂ) up will cause the ANVIL (1ꢂ) to move in
a counterclockwise direction. This will com-
monly loosen the fastener.
Rocker Switch
(# ꢂ)
Figure 1 -- operation
ꢁ.
Pressing the bottom of the ROCKER SWITCH down will cause the ANVIL to move in a
clockwise direction. This will commonly tighten the fastener.
“Breaking Loose” Fasteners
Note: This procedure is used when a fastener becomes “frozen”, typically due to corrosion.
This procedure assumes that the threads are standard (clockwise to tighten, counter
clockwise to loosen). If the threads are reversed, you must reverse the switch directions
contained herein.
1.
Spray silicon or another appropriate lubricant on the fastener and allow it to sit for 1ꢁ-30
minutes.
ꢀ.
Rapidly press the ROCKER SWITCH (ꢂ) up and then down. This will cause the ANVIL
(1ꢂ) change direction rapidly and loosen the bolt.
SKU 31877
For technical questions, please call 1-800-444-3353.
Page 7
MAINTENANCE
Risk of serious personal injury from accidental starting or electric
shock. Turn the Power Switch of the tool to its “OFF” position and
unplug the tool from its electrical outlet before performing any
inspection, maintenance, or cleaning procedures.
WARNINg
damaged equipment can fail, causing serious personal injury.
do not use damaged equipment. If abnormal noise or vibration
occurs, have the problem corrected before further use.
1.
BEFORE EACH uSE, inspect the general condition of the tool. Check for loose screws,
misalignment or binding of moving parts, cracked or broken parts, damaged electrical
wiring, and any other condition that may affect its safe operation.
ꢀ.
3.
AFTER uSE, clean external surfaces of the tool with clean, moist cloth.
WARNINg! If the supply cord of this power tool is damaged, it must be replaced
only by a qualified service technician.
Brushes
Note: Both BRUSHES (3) must be replaced at the
Brush
(# 3)
same time.
1.
ꢀ.
The BRUSHES must be changed when
less than 3/8” remains or when perfor-
mance noticeably degrades.
Remove the BRUSH CAP (ꢁ) using a large,
flat-head screwdriver.
Brush Cap
(# ꢁ)
3.
4.
Remove the BRUSH and replace.
Replace the BRUSH CAP.
Figure 2 -- Brush Replacement
Lubrication
Note: The following procedures should only be attempted by a qualified technician. The in-
structions are only provided for their reference. Refer to the Parts Diagram for num-
bered call-outs.
1.
The gears must be lubricated after every 30 hours of continuous use or ꢁ0 hours of inter-
mittent use.
ꢀ.
3.
Open the GEAR CASE (13) by removing the four SCREWS (1ꢀ).
Liberally apply a high temperature grease (standard automotive wheel grease is suf-
ficient). to the THRUST WASHER (14), the back of the ANVIL (16), IMPACTOR (19),
SPRING (21), and GEARS (22 & #27).
4.
Replace the ANVIL and GEAR CASE.
SKU 31877
For technical questions, please call 1-800-444-3353.
Page 8
PLEASE REAd THE FOLLOWINg CAREFuLLY
THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND ASSEMBLY
DIAGRAM IN THIS MANUAL AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER OR
DISTRIBUTOR MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT
HE OR SHE IS QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT, OR THAT HE OR SHE IS
QUALIFIED TO REPLACE ANY PARTS OF THE PRODUCT. IN FACT, THE MANUFACTURER AND/OR
DISTRIBUTOR ExPRESSLY STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD
BE UNDERTAKEN BY CERTIFIED AND LICENSED TECHNICIANS, AND NOT BY THE BUYER. THE
BUYER ASSUMES ALL RISK AND LIABILITY ARISING OUT OF HIS OR HER REPAIRS TO THE
ORIGINAL PRODUCT OR REPLACEMENT PARTS THERETO, OR ARISING OUT OF HIS OR HER
INSTALLATION OF REPLACEMENT PARTS THERETO.
PARTS LIST
Part
1
ꢀ
3
4
ꢁ
ꢂ
7
8
description
Q’ty
1
1
ꢀ
ꢀ
ꢀ
1
1
1
1
1
1
ꢂ
1
1
1
1
Part
ꢀ4
ꢀꢁ
ꢀꢂ
ꢀ7
ꢀ8
ꢀ9
30
31
3ꢀ
33
34
3ꢁ
3ꢂ
37
38
39
40
41
4ꢀ
44
4ꢁ
4ꢂ
47
description
Q’ty
1
ꢀ
ꢀ
1
1
1
1
1
1
1
1
ꢀ
1
1
ꢂ
1
1
ꢂ
1
ꢀ
1
1
1
Armature*
Field
Bearing
Washer
Brush Assembly
Brush Holder
Brush Cap
Switch
Needle Bearing
Gear & Pinion*
Gasket
Gear Case Cover*
Fan Baffle
Wire Connector
Rubber Clip
Handle Cover
Field Case
Screw
Cord Clamp*
Switch Support
Screw*
O-Ring*
End Cap
Plug
Cord
9
Ball Bearing
Ball Bearing*
Bearing Retainer
Screw
Gear Case*
Thrust Washer*
Bearing & Seal
Anvil Assembly*
Spring
10
11
1ꢀ
13
14
1ꢁ
1ꢂ
17
18
19
ꢀ0
ꢀ1
ꢀꢀ
ꢀ3
1
1
1
ꢀꢁ
1
Detent Pin
Impactor
Steel Ball
Receptacle
Cord Sheath
Terminal
Roll Pin
Washer
Spring
Gear & Cam
Steel Ball
1
ꢀ
Name Plate
*Note:
1. Includes 9, 10, & 11.
10. Before assembling bearing into rubber boot, coat O.D. with grease.
13. Includes 1ꢁ.
14. When assembling, make sure bevel side is towards the ears of the anvil.
16. Includes 17 & 18.
ꢀ7. Includes ꢀꢂ.
ꢀ9. Includes ꢀ4.
3ꢂ. Convex side towards cable.
38. Torque from 22 to 27 in-lb.
39. Fits on bearing O.D.
SKU 31877
For technical questions, please call 1-800-444-3353.
Page 9
ASSEMBLY dIAgRAM
Record Product’s Serial Number Here:
Note: If product has no serial number, record month and year of purchase instead.
Note: Some parts are listed and shown for illustration purposes only, and are not available
individually as replacement parts.
SKU 31877
For technical questions, please call 1-800-444-3353.
Page 10
LIMITEd 90 dAY WARRANTY
Harbor Freight Tools Co. makes every effort to assure that its products meet high qual-
ity and durability standards, and warrants to the original purchaser that this product is free from
defects in materials and workmanship for the period of 90 days from the date of purchase. This
warranty does not apply to damage due directly or indirectly, to misuse, abuse, negligence or
accidents, repairs or alterations outside our facilities, criminal activity, improper installation, nor-
mal wear and tear, or to lack of maintenance. We shall in no event be liable for death, injuries
to persons or property, or for incidental, contingent, special or consequential damages arising
from the use of our product. Some states do not allow the exclusion or limitation of incidental or
consequential damages, so the above limitation of exclusion may not apply to you. THIS WAR-
RANTY IS ExPRESSLY IN LIEU OF ALL OTHER WARRANTIES, ExPRESS OR IMPLIED,
INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS.
To take advantage of this warranty, the product or part must be returned to us with trans-
portation charges prepaid. Proof of purchase date and an explanation of the complaint must
accompany the merchandise. If our inspection verifies the defect, we will either repair or replace
the product at our election or we may elect to refund the purchase price if we cannot readily and
quickly provide you with a replacement. We will return repaired products at our expense, but if
we determine there is no defect, or that the defect resulted from causes not within the scope of
our warranty, then you must bear the cost of returning the product.
This warranty gives you specific legal rights and you may also have other rights which
vary from state to state.
3491 Mission oaks Blvd. • Po Box 6009 • camarillo, cA 93011 • (800) 444-3353
SKU 31877
For technical questions, please call 1-800-444-3353.
Page 11
|