Harbor Freight Tools Inflatable Bouncy Toy 95041 User Manual

ELECTRIC KEY BOX  
95041  
ASSEMBLY & OPERATING INSTRUCTIONS  
Due to continuing improvement, actual product may differ slightly from the product described herein.  
Note: Harbor Freight Tools is not responsible for the loss of any property stored within this  
safe due to theft, fire, or any other circumstance.  
®
3491 Mission Oaks Blvd., Camarillo, CA 93011  
Copyright© 2006 by Harbor Freight Tools®. All rights reserved. No portion of this manual or  
any artwork contained herein may be reproduced in any shape or form without the  
express written consent of Harbor Freight Tools.  
For technical questions and replacement parts please call 1-800-444-3353.  
 
N0TE:  
Harbor Freight Tools is not responsible for the loss of any property stored  
within this safe due to theft, fire, or any other circumstance.  
WARNING: The warnings, cautions, and instructions discussed in this instruction manual cannot  
cover all possible conditions and situations that may occur. It must be understood by  
the operator that common sense and caution are factors which cannot be built into  
this product, but must be supplied by the operator.  
Unpacking  
When unpacking your Key Box, check to make sure that all parts listed in the parts list on page 5 are  
included. If any parts are missing or broken, please call HARBOR FREIGHT TOOLS at  
1-800-444-3353. It is important that you read the entire manual to become familiar with the product  
BEFORE you operate and use the Key Box.  
Operation  
Your Key Box comes completely assembled. It is important that you read the entire manual to  
become familiar with the product BEFORE you set up and use the Key Box.  
1.  
Opening the Key Box for the first time: On the Keypad (7) enter the factory preset  
Personal Identification Number (PIN) which is 159B. When the Green LED light goes on,  
turn the Knob (4) clockwise and the Key Box will open-see Assembly Diagram.  
2.  
To program your own PIN: On the Keypad (7) enter the factory preset PIN which is 159B.  
When the Green LED Light goes on, turn the Knob (4) clockwise and the Key Box will open-  
see Assembly Diagram. Press the Red Button (11) on the inside of the door near the hinges.  
Select a new PIN, with 3 to 8 numbers, and press the “B” key.  
The green light will go on to indicate that the PIN has been successfully programmed. Make  
a note of the new PIN and store it in a safe place away from the Key Box.  
Test your new PIN before closing the door. Make certain you have a Manual Override Key(8)  
available when setting a new PIN or changing batteries in case the door doesn’t open.  
Note: The Knob (4) on the Door must be turned within 5 seconds of the green light coming on, or  
else the PIN must be re-entered.  
Note: If you or an intruder incorrectly enter the PIN, the yellow light will go on. Entering an incorrect  
PIN three times will freeze the system for 20 seconds.  
3.  
4.  
Using the Manual Override Key (8) : The Manual Override Keys can be used if you  
forget your PIN, if the batteries are not installed in the Key Box, or if the batteries are dead.  
NEVER lock your Manual Override Keys (8) into the Key Box, store them seperately  
in a safe place.  
At the center of the Key Box door (see Assembly diagram) is the Key Cover (5). Remove the  
Cover (5) and pull the panel outward to expose the key hole. Insert the Manual Override  
Key (8) and turn counterclockwise. Turn the Knob and pull the door open.  
SKU 95041  
For technical questions please call 1-800-444-3353.  
Page 3  
 
5.  
6.  
To close and lock the Key Box: Close the door and turn the Knob in the opposite direction  
used to open the Key Box. Pull the door gently to make certain it is properly locked.  
Installing batteries: The red LED light on the Keypad (7) will light up when the batteries  
need replacing. When this light appears, IMMEDIATELY replace the batteries.  
Open the Safe door. Unsnap the Battery Cover (10) from the Door. Remove the old  
batteries and install four new “AA” batteries in their place in the battery compartment. Make  
certain to align the polarity of the batteries as indicated in the battery compartment. Snap in  
the Battery Cover (10).  
7.  
8.  
After replacing the batteries, the PIN may need to be reset. To reset PIN, follow instructions  
in Step 2 on page 3.  
Mounting the Key Box: To mount the Key Box to a wall or surface, use a drill to set the path  
for each Bolt (9). Make certain that the drilling path is clear and free of obstacles  
such as wires, cables and electrical lines. Use wall anchors (not included) as  
necessary. Insert the Bolts (9) (included) through each drilled hole and into a stud to  
secure the Key Box to the desired surface.  
9.  
The Key Box comes with four Steel Hook Hanger Brackets (13). These come in four colors  
to match the Plastic Key Hanger Rings which also come in (4) colors.  
10.  
Install the Steel Hook Hanger Brackets (13) either onto the slots on the inside of the Key Box,  
the Door or both. The four Steel Hook Hanger Brackets are numbered 1 through 20. Once  
the Steel Hook Brackets are installed, the Plastic Key Rings (12) can be hung on them. The  
Plastic Key Rings can be set to correspond to either the number or color of the Steel Hook  
Hanger Brackets (13).  
Maintenance  
1.  
Protect the Key Box from moist or wet conditions. Moisture may cause electronic damage in  
the keypad or corrosion of the steel.  
2.  
3.  
Occasionally wipe the Key Box and keypad clean with a soft dry cloth or brush.  
Occasionally apply a small amount of light oil or lock lubricant to the mechanical lock  
mechanism. Be careful not to get any oil or other liquids on or near the electronic  
mechanism.  
PLEASE READ THE FOLLOWING CAREFULLY  
THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS DIAGRAM IN THIS MANUAL AS A  
REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER NOR DISTRIBUTOR MAKES ANY REPRESENTATION OR  
WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT  
OR THAT HE OR SHE IS QUALIFIED TO REPLACE ANY PARTS OF THE PRODUCT. IN FACT, THE MANUFACTURER AND/  
OR DISTRIBUTOR EXPRESSLY STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN BY  
CERTIFIED AND LICENSED TECHNICIANS AND NOT BY THE BUYER. THE BUYER ASSUMES ALL RISK AND LIABILITY  
ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS THERETO, OR ARISING  
OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO.  
SKU 95041  
For technical questions please call 1-800-444-3353.  
Page 4  
 
Parts List  
Part Description  
Quantity  
1
2
3
4
5
6
Body  
Door  
Front Cover  
Knob  
Key Cover  
LED Light  
1
1
1
1
1
3
(Green, Yellow, Red)  
Keypad  
7
1
8
Manual Override Key 2  
9
Bolt  
2
10  
11  
12  
13  
Battery Cover  
Red Button  
Plastic Key Ring  
Steel Hook Hanger  
Brackets  
1
1
20  
4
2
14  
Steel Wall Anchors  
Note: Some parts are listed and shown for illustration purposes only and are not available  
individually as replacement parts.  
Parts/Assembly Diagram  
13  
14  
12  
14 Not shown  
SKU 95041  
For technical questions please call 1-800-444-3353.  
Page 5  
 

Graco Flat Panel Television 244561 User Manual
Graco Inc Power Roller 244278 User Manual
Grizzly Planer G1021Z User Manual
Hamilton Beach Coffeemaker 840124800 User Manual
Hawking Technology Network Card PS12U User Manual
Honeywell Portable Generator 6036 User Manual
Hotpoint Oven AHP662K 1 User Manual
Humminbird Fish Finder Matrix 17 User Manual
Hunter Fan Outdoor Ceiling Fan 41449 01 05 00 User Manual
Husqvarna Snow Blower 1830HV User Manual