Harbor Freight Tools Laser Level 90980 User Manual

16” LASER LEVEL  
WITH 360° ROTATING HEAD  
90980  
ASSEMBLY & OPERATING INSTRUCTIONS  
®
3491 Mission Oaks Blvd., Camarillo, CA 93011  
Copyright© 2003 by Harbor Freight Tools®. All rights reserved. No portion of this manual or  
any artwork contained herein may be reproduced in any shape or form without the  
express written consent of Harbor Freight Tools.  
For technical questions and replacement parts please call 1-800-444-3353.  
 
12. Make certain to switch the Laser Level to the “OFF” position when adjusting or when  
changing the batteries.  
13. Use the right tool for the job. There are certain applications for which this tool was designed. Do  
not modify this tool and do not use this tool for a purpose for which it was not intended.  
14. Remove batteries if the Laser Level is not used for a long period of time.  
15. Do not operate tool if under the influence of alcohol or drugs. Read warning labels on  
prescriptions to determine if your judgment or reflexes are impaired while taking drugs. If there is  
any doubt, do not operate the tool.  
Note:  
Always switch to a fresh battery when tool performance begins to diminish. This is a  
delicate instrument, do not drop or jar the Laser Level.  
Warning:  
The warnings, cautions, and instructions discussed in this instruction manual cannot  
cover all possible conditions and situations that may occur. It must be understood by  
the operator that common sense and caution are factors which cannot be built into this  
product, but must be supplied by the operator.  
Assembly/ Operation  
Your Laser Level will require some assembly prior to use. It is important that you read the entire  
manual to become familiar with the product BEFORE you use the Laser Level. Before assembling and  
operating the Laser Level be sure that you have all parts described in the Parts List and Assembly  
Diagram located on the last pages of this manual.  
Figure 2  
Figure 1  
leg of  
Tripod (15)  
latch  
Plastic Body (5)  
Knob (14)  
Knob (17)  
Tripod slot  
arms  
1.  
2.  
Unfold the Tripod (15) by pulling out on the Tripod arms. Turn the Knob (17) to lock the arms in  
place-see Figure 1.  
The legs of the Tripod (15) can be raised or lowered by lifting the latch on the body of the Tripod  
(15) and sliding the leg in or out to the desired height-see Figure 1. Push the latch down into  
place to secure the Leg into position. Repeat for the remaining two legs.  
3.  
4.  
Set the Tripod on a flat surface. Once the Tripod (15) is set up, you can raise and lower the  
Rotating Head (7) by turning the Handle (18) located at the top of the Tripod (15) -see Figure 3.  
Wind the Handle (18) clockwise to raise the Rotating Head (7) and counterclockwise to lower the  
Rotating Head (7) -see Figure 3.  
Initial Leveling of the Rotating Head (7):  
Turn the three Adjusting Knobs (16) one at a time to level the Rotating Head (7). Keep turning the  
Adjusting Knobs (16) until the Bulls-Eye Bubble (19) floats exactly in the center of the circle. If  
you are out of level, the air bubble will float to the side of the Bulls-Eye Bubble-see Figure 4.  
Note: The Bulls-Eye Bubble (19) is intended for initial leveling of the Rotating Head (7) only.  
After placing the Plastic Body (5) into the tripod slot, further leveling should be done  
using the Horizontal Bubble (4) as a reference.  
REV 03/04  
SKU 90980  
Page 3  
 
Rotating  
Head (7)  
Horizontal Bubble (4)  
Vertical Bubble (3)  
Handle (18)  
Tripod (15)  
Adjusting Knob (16)  
Figure 3  
Figure 4  
5.  
6.  
Set the Plastic Body (5) into the slot in the Tripod-see Figure 2. Tighten down  
the Knob (14) on the top of the Tripod to secure the Plastic Body (5) in place-  
see Figure 2, page 3.  
Leveling A  
How to Level the Laser:  
Note: The numbers here are only for reference, the knobs are not numbered.  
a. Set the level parallel to knobs1and2as shown in Leveling A. Adjust knobs1and  
‘2’ until the Horizontal Bubble (4) is in the center.  
b. Turn the level 90°. It should now be over knob ‘3’ as shown in Leveling B. Adjust  
knob ‘3until the Horizontal Bubble (4) is again in the center.  
c. Turn the level back 90°, to the position shown in Leveling B. The Horizontal Bubble  
(4) should still be in the center. If it is not, repeat the steps above. If, after repeated  
attempts, the level is still uneven check all mountings to ensure nothing is loose and  
that the Plastic Body (5) is properly seated in the tripod slot.  
Leveling B  
7.  
8.  
Once the Laser Level is set in the Tripod, you may set the laser to the type of  
beam you wish to use. The laser projects up to 1,500 feet. Set the Lens  
Fixture (11) “Down”; and this mode will fix the Level Laser beam to a beam  
splitter (-) mode. The beam splitter mode will project a horizontal line. Set the  
Lens Fixture (11) to the top mode and this mode will set the Laser Level beam  
to a dot (.)-see Figure 5. Turn the Laser Level “ON” by pressing the “ON/OFF”  
button (9) -see Figure 5. Be careful not to point the Laser Level at anyone.  
Once you have leveled the Level Laser  
in the Tripod (15), you can use it for  
many applications. Rotating the  
Rotating Head (7) with the laser ON  
and set to the beam splitter (-) mode,  
you can set a line of equal height in a  
room to verify alignment of pictures,  
electrical plugs, or shelving. The Laser  
Level can also be used to set a level  
for any surface while providing a bright  
beam to mark your settings by.  
Battery Cover (13)  
On/Off Button (9)  
Lens Fixture (11)  
Install batteries to match  
diagram  
Figure 5  
PLEASE READ THE FOLLOWING CAREFULLY  
THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS DIAGRAM IN THIS MANUAL AS A  
REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER NOR DISTRIBUTOR MAKES ANY REPRESENTATION OR  
WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT OR  
THAT HE OR SHE IS QUALIFIED TO REPLACE ANY PARTS OF THE PRODUCT. IN FACT, THE MANUFACTURER AND/OR  
DISTRIBUTOR EXPRESSLY STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN BY  
CERTIFIED AND LICENSED TECHNICIANS AND NOT BY THE BUYER. THE BUYER ASSUMES ALL RISK AND LIABILITY  
ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS THERETO, OR ARISING  
OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO.  
REV 03/04  
SKU 90980  
Page 4  
 
Warning:  
Always make certain the laser is off before adjusting or changing batteries.  
Installing and Removing Batteries  
1.  
The Laser Level uses two (2) “AAA” batteries. Remove the Battery Cover (13)  
located under the On/Off Button (9) -see Figure 5. Remove the old batteries and insert two  
new batteries. Line the batteries up the same way, so that positive and negative ends match  
the diagram on the end of the Laser Level. Replace the Battery Cover (13).  
Warning:  
People with pacemakers should consult with their physician before  
using this product; operation of equipment in close proximity to a  
heart pacemaker could cause interference or failure of the  
pacemaker.  
Warning:  
This product contains or produces a chemical known to the State  
of California to cause cancer and birth defects (or other  
reproductive harm). (California Health & Safety Code 25249.5 et  
seq.)  
Unpacking  
When unpacking your 16" Laser Level with 360° Rotating Leveling Head, check to make sure the  
following parts are included. If any parts are missing or broken, please call HARBOR FREIGHT  
TOOLS at 1-800-444-3353.  
Parts List  
Part # Description  
Quantity Part # Description  
Quantity  
1
2
3
4
5
6
7
8
9
Laser Aperture  
Back Cover  
Vertical Bubble  
Horizontal Bubble  
Plastic Body  
Laser Modules  
Rotating Head  
Battery Spring  
On/Off Button  
1
1
1
1
1
1
1
1
1
10  
11  
12  
13  
14  
15  
16  
17  
18  
Front Cover  
Lens Fixture  
Fan Lens  
Battery Cover  
Knob  
Tripod  
Adjusting Knob  
Knob  
Handle  
1
1
1
1
1
3
3
1
1
19  
Bulls-Eye Bubble  
2
Assembly/Parts Diagram  
19  
13  
9
8
4 5  
3
6
2
18  
15  
14  
11  
1
16  
12  
10  
7
17  
Note: Some parts are listed and shown for illustration purposes only and are not available  
individually as replacement parts.  
SKU 90980  
Page 5  
 

Graco Septic System 03761B User Manual
Grizzly Outboard Motor H5373 User Manual
Hamilton Beach Juicer 395W User Manual
Havis Shields Camcorder Accessories KR 800 User Manual
Honeywell Humidifier HE360A1075 User Manual
Honeywell Water Pump S8600 User Manual
Hubbell Fishing Equipment UE21 User Manual
Hunter Fan Thermostat 44127 User Manual
Husqvarna Blower 953210103 User Manual
Husqvarna Chainsaw 115 13 82 49 User Manual