COMBINATION
PICNIC TABLE - BENCH
Model 97736
AssEMBLy & sET-UP INsTrUCTIONs
Diagrams within this manual may not be drawn proportionally.
Due to continuing improvements, actual product may differ slightly from the product described herein.
®
Distributed exclusively by Harbor Freight Tools .
3491 Mission Oaks Blvd., Camarillo, CA 93011
read this material before using this product.
Failure to do so can result in serious injury.
sAVE THIs MANUAL.
©
®
Copyright 2008 by Harbor Freight Tools . All rights reserved. No portion of this
manual or any artwork contained herein may be reproduced in any shape or form
without the express written consent of Harbor Freight Tools.
For technical questions or replacement parts, please call 1-800-444-3353.
7.
8.
Never allow people or animals to stand
or climb on this product.
AssEMBLy
Pinch point warning: Use caution to
avoid pinching fingers when assembling
and setting up this unit.
Note: For additional information regarding the
parts listed in the following pages, refer to the
accompanying illustrations.
9.
Adults only should perform the assembly
and set-up of this product.
1.
Attach the two Folding Beams (2) flush to
the inner side of the Table Top (5), using
six Bolts each with two Washers and one
Nut (9). (see Figure A.)
10. When in use, make sure all Legs of the
product are flat on the ground.
2.
NOTE: The Bolts and Washers (9)
should be inserted from the outside of
the Table Top (5) into the Folding Beams
(2). (see Figure A.)
11. The warnings, precautions, and
instructions discussed in this instruction
manual cannot cover all possible
conditions and situations that may occur.
It must be understood by the operator
that common sense and caution are
factors which cannot be built into this
product, but must be supplied by the
operator.
FIGUrE A
TABLE TOP (5)
sAVE THEsE
FOLDING BEAM (2)
INsTrUCTIONs.
BOLTs, WAsHErs, NUTs (9)
sPECIFICATIONs
3.
4.
Place and align the Short Bench Top (8)
flush on the two Bench Supports (4).
(see Figure B.)
Unfinished Fir
Construction
Yellow/Green Zinc Plated Steel Bolts,
Material
Washers, Nuts, and Screws
400 Pounds Total
Weight Capacity
(Distributed Evenly)
Fasten the eight Screws (11) into the
pre-drilled holes on the Short Bench
Top (8) to the Bench Supports (4). (see
Figure B.)
Umbrella Hole
1-5/8”
Diameter
Waterproof
No
Water Resistant
sCrEWs (11)
FIGUrE B
UNPACkING
sHOrT
BENCH
TOP
When unpacking, check to make sure that
the item is intact and undamaged. If any parts
are missing or broken, please call Harbor Freight
Tools at the number shown on the cover of this
manual as soon as possible.
BENCH sUPPOrT (4)
(8)
SKU 97736
For technical questions, please call 1-800-444-3353.
Page 3
5.
6.
Turn the assembled Bench upside down. 10. Hold the Table securely in its standing
position.
Position the Diagonal Supports (7) so
one end is against the longer cross
beam of Bench Support (4) legs. Then
align the other end so it is flush to the
wood edge next to the center gap of the
Short Bench Top (8). The two Diagonal
Supports (7) need to be attached at
opposite sides of the bench gap, using
three Screws (11) per Support. (i.e., one
support will be attached to one bench
slat, and the other bench slat will be
attached to the other bench support.
(see Figure C.)
11. Attach the two Table Legs (1) to the
Table Top (5) by inserting two Bolts
each, with four Washers and one Nut
(10) into the pre-drilled hole at the
rounded end of the Table Legs. NOTE:
One pre-drilled hole still remains below
the Table Legs. (see Figure E.)
TABLE TOP (5)
7.
NOTE: There are no pre-drilled holes
for the Screws (11) in the bench slat
or Bench Supports (4). Instead, there
are guide marks in the wood to indicate
where the Screws must be inserted.
TABLE LEG
(1)
BOLTs, WAsHErs, NUTs (10)
(see Figure C.)
BENCH
FIGUrE E
sUPPOrT
DIAGONAL
sUPPOrT
(4)
12. Attach the two Arm Rests (3) to the Table
Legs (1), using two Bolts, each with four
Washers and one Nut (10). (see Figure
F.)
(7)
sHOrT
BENCH
TOP (8)
FIGUrE C
FIGUrE F
TABLE LEG (1)
8.
9.
Set the Table on its side.
Attach the Folding Beams (2) to the
outside edge of the Bench Supports (4),
using two Bolts, each with four Washers,
and one Nut (10).
BOLTs
WAsHErs
NUTs
ArM
rEsT
(3)
(see Figure D.)
(10)
13. Place the Long Bench Top (6) on the
Table Legs (1). Make sure the longer
bar underneath the Long Bench top is
toward the outside.
(see Figure G.)
14. Fasten the eight Screws (11) into the
pre-drilled holes in the Long Bench Top
(6) to the Table Legs (1).
FOLDING BEAM (2)
BOLTs, WAsHErs, NUTs (10)
FIGUrE D
(see Figure G.)
SKU 97736
For technical questions, please call 1-800-444-3353.
Page 4
LONG
BENCH
TOP
FIGUrE G
sCrEWs (11)
INsPECTION AND
MAINTENANCE
(6)
1.
2.
PErIODICALLy, inspect the general
condition of the Picnic Table/Bench.
Check for loose connections, improper
weight distribution, and any other
condition that may affect the product’s
operation.
TABLE LEG
(1)
15. To transform the Picnic Table into a
Bench, simply lift up the Table Top (5)
and Arm Rests (3).
TO CLEAN, use a damp cloth with a
mild detergent. Then dry. Do not use
solvents.
(see Figures H, I, and J.)
PLEAsE rEAD THE
FOLLOWING CArEFULLy
THE MANUFACTURER AND/OR DISTRIBUTOR
HASPROvIDEDTHEPARTSLISTANDASSEMBLY
DIAGRAM IN THIS MANUAL AS A REFERENCE
TOOLONLY. NEITHERTHEMANUFACTUREROR
DISTRIBUTOR MAKES ANY REPRESENTATION
OR WARRANTY OF ANY KIND TO THE BUYER
THAT HE OR SHE IS qUALIFIED TO MAKE ANY
REPAIRS TO THE PRODUCT, OR THAT HE OR
SHE IS qUALIFIED TO REPLACE ANY PARTS OF
THE PRODUCT. IN FACT, THE MANUFACTURER
AND/OR DISTRIBUTOR ExPRESSLY STATES
THATALLREPAIRSANDPARTSREPLACEMENTS
SHOULD BE UNDERTAKEN BY CERTIFIED AND
LICENSED TECHNICIANS, AND NOT BY THE
BUYER. THE BUYER ASSUMES ALL RISK AND
LIABILITYARISINGOUTOFHISORHERREPAIRS
TOTHEORIGINALPRODUCTORREPLACEMENT
PARTS THERETO, OR ARISING OUT OF HIS OR
HER INSTALLATION OF REPLACEMENT PARTS
THERETO.
FIGUrE H
LIFT UPWArDs
FIGUrE I
FIGUrE J
16. IMPOrTANT: To extend the life of this
Picnic Table/Bench, it is recommended
that you thoroughly coat it with an
appropriate protectant (i.e., paint,
varnish, etc.).
SKU 97736
For technical questions, please call 1-800-444-3353.
Page 5
PArTs LIsT & AssEMBLy DIAGrAM
Part #
Description
Table Leg
Qty.
2
Part #
Description
Diagonal Support
Qty.
2
1
2
3
4
5
6
7
8
Folding Beam
Arm Rest
2
Short Bench Top
1
2
9
Bolt w/Two Washers & One Nut
Bolt w/Four Washers & One Nut
Screw
6
Bench Support
Table Top
2
10
11
6
1
22
Long Bench Top
1
2
1
3
4
9
5
10
11
7
6
8
SKU 97736
For technical questions, please call 1-800-444-3353.
Page 6
LIMITED 90 DAy WArrANTy
Harbor Freight Tools Co. makes every effort to assure that its products meet high
quality and durability standards, and warrants to the original purchaser that this product
is free from defects in materials and workmanship for the period of 90 days from the date
of purchase. This warranty does not apply to damage due directly or indirectly, to misuse,
abuse, negligence or accidents, repairs or alterations outside our facilities, criminal activity,
improper installation, normal wear and tear, or to lack of maintenance. We shall in no event
be liable for death, injuries to persons or property, or for incidental, contingent, special
or consequential damages arising from the use of our product. Some states do not allow
the exclusion or limitation of incidental or consequential damages, so the above limitation
of exclusion may not apply to you. THIS WARRANTY IS ExPRESSLY IN LIEU OF ALL
OTHER WARRANTIES, ExPRESS OR IMPLIED, INCLUDING THE WARRANTIES OF
MERCHANTABILITY AND FITNESS.
To take advantage of this warranty, the product or part must be returned to us with
transportation charges prepaid. Proof of purchase date and an explanation of the complaint
must accompany the merchandise. If our inspection verifies the defect, we will either
repair or replace the product at our election or we may elect to refund the purchase price
if we cannot readily and quickly provide you with a replacement. We will return repaired
products at our expense, but if we determine there is no defect, or that the defect resulted
from causes not within the scope of our warranty, then you must bear the cost of returning
the product.
This warranty gives you specific legal rights and you may also have other rights which
vary from state to state.
3491 Mission Oaks Blvd. • PO Box 6009 • Camarillo, CA 93011 • (800) 444-3353
record Product’s serial Number Here:
Note: If product has no serial number, record month and year of purchase instead.
Note: Some parts are listed and shown for illustration purposes only, and are not
available individually as replacement parts.
SKU 97736
For technical questions, please call 1-800-444-3353.
Page 7
|