DEMOLITION HAMMER
Model 68148
SET UP AND OPERATING INSTRUCTIONS
Read this material before using this product.
Failure to do so can result in serious injury.
SAVE THIS MANUAL.
©
®
Copyright 2010 by Harbor Freight Tools . All rights reserved. No portion of this manual or any artwork
contained herein may be reproduced in any shape or form without the express written consent of
Harbor Freight Tools. Diagrams within this manual may not be drawn proportionally. Due to continuing
improvements, actual product may differ slightly from the product described herein. Tools required for
assembly and service may not be included.
For technical questions or replacement parts, please call 1‑800‑444‑3353.
entering a power tool will increase
the risk of electric shock.
d. Do not overreach. Keep proper
footing and balance at all times.
This enables better control of the
power tool in unexpected situations.
c. Do not abuse the cord. Never
use the cord for carrying, pulling
or unplugging the power tool.
Keep cord away from heat, oil,
sharp edges or moving parts.
Damaged or entangled cords
e. Dress properly. Do not wear
loose clothing or jewelry. Keep
your hair, clothing and gloves
away from moving parts. Loose
clothes, jewelry or long hair can
be caught in moving parts.
increase the risk of electric shock.
d. When operating a power tool
outdoors, use an extension cord
suitable for outdoor use. Use
of a cord suitable for outdoor use
reduces the risk of electric shock.
f. Only use safety equipment that has
been approved by an appropriate
standards agency. Unapproved
safety equipment may not provide
adequate protection. Eye protection
must be ANSI-approved and breathing
protection must be NIOSH-approved for
the specific hazards in the work area.
e. If operating a power tool in a damp
location is unavoidable, use a
Ground Fault Circuit Interrupter
(GFCI) protected supply. Use of a
GFCI reduces the risk of electric shock.
4. Power tool use and care
3. Personal safety
a. Do not force the power tool. Use
the correct power tool for your
application. The correct power tool
will do the job better and safer at
the rate for which it was designed.
a. Stay alert, watch what you are
doing and use common sense when
operating a power tool. Do not use
a power tool while you are tired
or under the influence of drugs,
alcohol or medication. A moment of
inattention while operating power tools
may result in serious personal injury.
b. Do not use the power tool if the
switch does not turn it on and
off. Any power tool that cannot
be controlled with the switch is
dangerous and must be repaired.
b. Use personal protective equipment.
Always wear eye protection. Safety
equipment such as dust mask, non-
skid safety shoes, hard hat, or hearing
protection used for appropriate
c. Disconnect the plug from the
power source and/or the battery
pack from the power tool before
making any adjustments, changing
accessories, or storing power
tools. Such preventive safety
conditions will reduce personal injuries.
c. Prevent unintentional starting.
Ensure the switch is in the off‑
position before connecting to power
source and/or battery pack, picking
up or carrying the tool. Carrying
power tools with your finger on the
switch or energizing power tools that
have the switch on invites accidents.
measures reduce the risk of starting
the power tool accidentally.
d. Store idle power tools out of
the reach of children and do
not allow persons unfamiliar
with the power tool or these
instructions to operate the power
tool. Power tools are dangerous
in the hands of untrained users.
SKU 68148
For technical questions, please call 1‑800‑444‑3353.
Page 3
e. Maintain power tools. Check for
misalignment or binding of moving
parts, breakage of parts and any
other condition that may affect the
power tool’s operation. If damaged,
have the power tool repaired before
use. Many accidents are caused
by poorly maintained power tools.
5. Unplug before inspecting,
removing or installing chisel,
or performing any service.
6. Pull on chisel after installation
and before use; chisel may move
but MUST NOT slide out.
7. Do not operate this tool if you have
back, neck, or wrist injuries, or other
conditions that will be aggravated
by the severe jerking forces that this
tool exerts upon the operator.
f. Keep cutting tools sharp and clean.
Properly maintained cutting tools with
sharp cutting edges are less likely
to bind and are easier to control.
g. Use the power tool, accessories
and tool bits etc. in accordance
with these instructions, taking into
account the working conditions
and the work to be performed.
Use of the power tool for operations
different from those intended could
result in a hazardous situation.
8. Maintain labels and nameplates
on the tool. These carry important
safety information. If unreadable
or missing, contact Harbor Freight
Tools for a replacement.
9. Avoid unintentional starting. Prepare to
begin work before turning on the tool.
10. Do not lay the tool down until it has
come to a complete stop. Moving
parts can grab the surface and
5. Service
a. Have your power tool serviced by
a qualified repair person using
only identical replacement parts.
This will ensure that the safety of
the power tool is maintained.
pull the tool out of your control.
11. When using a handheld power tool,
maintain a firm grip on the tool with
both hands to resist starting torque.
Breaker Hammer Safety Warnings
12. Do not leave the tool unattended when
it is plugged into an electrical outlet.
Turn off the tool, and unplug it from
its electrical outlet before leaving.
1. Wear ear protectors. Exposure to
noise can cause hearing loss.
2. Use auxiliary handles supplied
with the tool. Loss of control
can cause personal injury.
13. This product is not a toy. Keep
it out of reach of children.
3. Hold power tools by insulated
gripping surfaces when performing
an operation where the cutting tool
may contact hidden wiring or its
own cord. Contact with a ″live″ wire
will make exposed metal parts of the
tool ″live″ and shock the operator.
14. People with pacemakers should
consult their physician(s) before use.
Electromagnetic fields in close proximity
to heart pacemaker could cause
pacemaker interference or pacemaker
failure. In addition, people with
pacemakers should:
• Avoid operating alone.
• Properly maintain and inspect to avoid
electrical shock.
4. Keep clear of moving parts.
Page 4
For technical questions, please call 1‑800‑444‑3353.
SKU 68148
• Any power cord must be properly
grounded. Ground Fault Circuit
Interrupter (GFCI) should also
be implemented – it prevents
sustained electrical shock.
Vibration Safety
This tool vibrates during use. Repeated
or long-term exposure to vibration
may cause temporary or permanent
physical injury, particularly to the
hands, arms and shoulders. To reduce
the risk of vibration-related injury:
15. WARNING: Some dust created by power
sanding, sawing, grinding, drilling, and
other construction activities, contains
chemicals known [to the State of
1. Anyone using vibrating tools regularly
or for an extended period should first
be examined by a doctor and then
have regular medical check-ups to
ensure medical problems are not
being caused or worsened from use.
Pregnant women or people who have
impaired blood circulation to the hand,
past hand injuries, nervous system
disorders, diabetes, or Raynaud’s
Disease should not use this tool. If
you feel any symptoms related to
vibration (such as tingling, numbness,
and white or blue fingers), seek
California] to cause cancer, birth defects
or other reproductive harm. Some
examples of these chemicals are:
• Lead from lead-based paints
• Crystalline silica from bricks and
cement or other masonry products
• Arsenic and chromium from chemically
treated lumber
Your risk from these exposures varies,
depending on how often you do this type
of work. To reduce your exposure to
these chemicals: work in a well ventilated
area, and work with approved safety
equipment, such as those dust masks
that are specially designed to filter out
microscopic particles. (California Health
& Safety Code § 25249.5, et seq.)
medical advice as soon as possible.
2. Do not smoke during use. Nicotine
reduces the blood supply to the
hands and fingers, increasing the
risk of vibration-related injury.
16. WARNING: Handling the cord on this
product will expose you to lead, a
3. Wear suitable gloves to reduce the
vibration effects on the user.
chemical known to the State of California
to cause cancer, and birth defects or
other reproductive harm. Wash hands
after handling. (California Health &
Safety Code § 25249.5, et seq.)
4. Use tools with the lowest vibration
when there is a choice.
5. Include vibration-free periods
17. The warnings, precautions, and
instructions discussed in this instruction
manual cannot cover all possible
conditions and situations that may
occur. It must be understood by the
operator that common sense and
caution are factors which cannot
be built into this product, but must
be supplied by the operator.
each day of work.
6. Let the tool do the work.
7. To reduce vibration, maintain
the tool as explained in this
manual. If any abnormal vibration
occurs, stop use immediately.
SAVE THESE
INSTRUCTIONS.
SKU 68148
For technical questions, please call 1‑800‑444‑3353.
Page 5
preceding illustration.
(See Outlets for 2‑Prong Plug.)
GROUNDING
TO PREVENT
ELECTRIC SHOCK
AND DEATH FROM INCORRECT
GROUNDING WIRE
Extension Cords
1. Grounded tools require a three
wire extension cord. Double
CONNECTION:
Insulated tools can use either a
two or three wire extension cord.
Check with a qualified electrician
if you are in doubt as to whether
the outlet is properly grounded.
Do not modify the power cord
plug provided with the tool.
Never remove the grounding
prong from the plug. Do not use
the tool if the power cord or plug
is damaged. If damaged, have it
repaired by a service facility
2. As the distance from the supply outlet
increases, you must use a heavier gauge
extension cord. Using extension cords
with inadequately sized wire causes a
serious drop in voltage, resulting in loss
of power and possible tool damage.
(See Table A.)
before use. If the plug will not fit 3. The smaller the gauge number of
the outlet, have a proper outlet
installed by a qualified
electrician.
the wire, the greater the capacity of
the cord. For example, a 14 gauge
cord can carry a higher current than
a 16 gauge cord. (See Table A.)
Double Insulated Tools: Tools
with Two Prong Plugs
4. When using more than one
extension cord to make up the
total length, make sure each cord
contains at least the minimum wire
size required. (See Table A.)
5. If you are using one extension
cord for more than one tool, add
the nameplate amperes and use
the sum to determine the required
minimum cord size. (See Table A.)
Outlets for 2‑Prong Plug
6. If you are using an extension cord
outdoors, make sure it is marked with
the suffix “W-A” (“W” in Canada) to
indicate it is acceptable for outdoor use.
1. Tools marked “Double Insulated” do
not require grounding. They have a
special double insulation system which
satisfies OSHA requirements and
complies with the applicable standards
of Underwriters Laboratories, Inc.,
the Canadian Standard Association,
and the National Electrical Code.
7. Make sure the extension cord is
properly wired and in good electrical
condition. Always replace a damaged
extension cord or have it repaired by
a qualified electrician before using it.
2. Double insulated tools may be used in
either of the 120 volt outlets shown in the
Page 6
For technical questions, please call 1‑800‑444‑3353.
SKU 68148
8. Protect the extension cords from
sharp objects, excessive heat,
and damp or wet areas.
RECOMMENDED MINIMUM WIRE GAUGE
FOR EXTENSION CORDS* (120/240 VOLT)
EXTENSION CORD
LENGTH
NAMEPLATE
AMPERES
(at full load)
25’ 50’ 75’ 100’ 150’
0 – 2.0
2.1 – 3.4
18
18
18
18
18
14
12
18
18
18
16
14
12
10
18
18
16
14
12
10
-
18
16
14
12
10
-
16
14
12
12
-
3.5 – 5.0
5.1 – 7.0
7.1 – 12.0
12.1 – 16.0
16.1 – 20.0
-
-
-
* Based on limiting the line
voltage drop to five volts at 150%
of the rated amperes.
TABLE A
Symbology
Double Insulated
Canadian Standards Association
Underwriters Laboratories, Inc.
Volts Alternating Current
Amperes
V~
A
No Load Revolutions
per Minute (RPM)
n xxxx/min.
0
SKU 68148
For technical questions, please call 1‑800‑444‑3353.
Page 7
SPECIFICATIONS
Electrical
Input
120 V~ / 60 Hz / 10 A
3100 BPM
Blows Per
Minute
Chisels
(included)
1 Bull Point
1 Flat Point
1 Oil Bottle
Other
1 Carbon Brush Set
Accessories 1 5mm Hex Key
1 Oil Tank Wrench
UNPACKING
When unpacking, make sure the item is intact and undamaged. If any parts are missing
or broken, please call Harbor Freight Tools at 1-800-444-3353 as soon as possible.
INSTRUCTIONS FOR PUTTING INTO USE
Read the ENTIRE IMPORTANT SAFETY INFORMATION section
at the beginning of this manual including all text under
subheadings therein before set up or use of this product.
Note: For additional information regarding the parts listed in the following
pages, refer to the Assembly Diagram near the end of this manual.
Functions
Use Figure 1 below as reference during Tool Setup and Operation.
Oil Tank Cover (12)
Trigger
(69)
Main
Handle
(74)
Chuck (35)
Flat Chisel
Side Handle (62)
Carbon Brush
Cap (54)
Figure 1
Page 8
For technical questions, please call 1‑800‑444‑3353.
SKU 68148
2. Pull the Chuck (35) back to open.
NOTE: If the Chuck is difficult to
open, lightly tap it with a hammer.
OPERATING INSTRUCTIONS
Read the ENTIRE IMPORTANT
SAFETY INFORMATION
section at the beginning of this
manual including all text under
subheadings therein before set
up or use of this product.
3. Insert the shank portion of the
chisel into Chuck as far as it
will go. Release the Chuck
4. Pull chisel to verify it is secure.
5. The Side Handle (62) can swing around
to either side of the tool. To adjust
its position, turn it counterclockwise
and slide to the desired position.
Tool Set Up
TO PREVENT
SERIOUS INJURY
FROM ACCIDENTAL
Turn it clockwise to lock it in place.
OPERATION: Turn Power Switch
off and unplug the tool from its
electrical outlet before adjusting
tool or installing accessories.
General Operating Instructions
1. Once the chisel is installed and
the Side Handle set in the desired
position, set the tip of the bit is
set against the work area.
Work Piece and Work Area Set Up
1. Designate a work area that is clean
and well-lit. The work area must
not allow access by children or pets
to prevent distraction and injury.
2. Place one hand on the Side
Handle and the other hand
around the Main Handle (74).
3. Press the Trigger (69) to activate
the Demolition Hammer.
2. Route the power cord along a safe
route to reach the work area without
creating a tripping hazard or exposing
the power cord to possible damage.
The power cord must reach the work
area with enough extra length to
4. NOTE: For continuous operation, press
the Trigger Switch and then push the
lock button located above the Trigger
Switch. To stop the continuous use,
press the Trigger Switch down all the
way and then release the Trigger Switch.
allow free movement while working.
3. Secure loose work pieces using
a vise or clamps (not included) to
prevent movement while working.
5. WARNING! Once activated, do not
press, bear down or thrust forcibly
against the work surface. Hold the
Demolition Hammer with just enough
pressure so that the tool’s own
4. There must not be objects, such
as utility lines, nearby that will
present a hazard while working.
weight supplies the needed force.
Mounting Tool Bits and
Locking Side Handle
6. NOTE: If the Demolition Hammer has
not been used for a long period of time
or is being used in low temperatures,
keep the tool running for about five
minutes to allow for warm-up. Make
1. WARNING! Before installing new bit,
verify Demolition Hammer is unplugged.
SKU 68148
For technical questions, please call 1‑800‑444‑3353.
Page 9
sure the Trigger Switch properly
actuates when pressed and that the
tool turns off when its released.
or broken parts, damaged electrical
wiring, and any other condition that
may affect its safe operation.
7. When work is complete,
release the Trigger Switch.
2. AFTER USE, wipe external surfaces
of the tool with clean cloth.
8. To prevent accidents, turn off the
tool and disconnect its power supply
after use. Clean, then store the tool
indoors out of children’s reach.
3. Wipe tool with a lint-free cloth
after each use to remove all
dust and grit from the tool.
NOTE: The Demolition Hammer has an
air‑tight construction, allowing for
three months of continuous usage
before any lubrication is needed.
MAINTENANCE AND
SERVICING
4. To add lubricating grease, use the Tank
Cover Wrench (91) to open the Tank
Cover (12). See Figure 1 on page 8.
Procedures not specifically
explained in this manual
must be performed only by
a qualified technician.
5. Fill with 1/8 ounce of lubricating
grease and replace Tank Cover.
NOTE: The Demolition Hammer will
cease operation once Carbon
Brushes are worn. Check
6. Examine tool before each use. Make
sure Chisel is sharp and not dull or
cracked. Replace worn or broken
Chisels with approved replacement
Chisels from Harbor Freight Tools.
Brushes every 100 hours and,
when necessary, replace them.
TO PREVENT
SERIOUS INJURY
FROM ACCIDENTAL
OPERATION: Release Trigger
Switch and unplug tool from its
electrical outlet before
performing inspection,
maintenance, or cleaning.
7. Check that all mounting screws are
tightened. Retighten any loose screws.
8. Store in temperatures no
lower than 50-60° F.
9.
WARNING! If the supply cord
of this power tool is damaged,
it must be replaced only by a
qualified service technician.
TO PREVENT SERIOUS INJURY
FROM TOOL FAILURE: Do not
use damaged equipment. If
abnormal noise or vibration
occurs, have the problem
Replacing Carbon Brushes
NOTE: The Demolition Hammer will
cease operation once Carbon
Brushes are worn. Check Brushes
every 100‑120 hours and, when
necessary, replace them.
corrected before further use.
Maintenance, and Lubrication
1. BEFORE EACH USE, inspect the
general condition of the tool. Check
for loose hardware, misalignment
or binding of moving parts, cracked
1. Use screwdriver to remove Carbon Brush
Cover (54). See Figure 1 on page 8.
Page 10
For technical questions, please call 1‑800‑444‑3353.
SKU 68148
2. Remove the Rubber Cap (53) and then
slide out the Carbon Brush Holder (51B).
6. WARNING! Verify all bolts and
connectors are fastened tight.
3. Remove the Brush Cap (52) from
the Carbon Brush Holder.
Cleaning
1. Clean the Demolition Hammer
with warm water, soap a soft cloth,
preferably after each use.
4. Remove old Carbon Brush (51) from
Carbon Brush Holder and insert new
Carbon Brush into Carbon Brush Holder.
2. WARNING! Do not use solvents
when cleaning the Electric Hammer.
Doing so can damaged the tool.
5. Replace Brush Cap and slide Carbon
Brush Holder back into Housing.
Replace Carbon Brush Cover.
Troubleshooting
Problem
Tool will not start.
Possible Causes
1. Cord not connected.
Likely Solutions
1. Check that cord is plugged in.
2. No power at outlet.
2. Check power at outlet. If outlet is unpowered,
turn off tool and check circuit breaker. If breaker
is tripped, make sure circuit is right capacity
for tool and circuit has no other loads.
3. Tool’s thermal reset breaker
tripped (if equipped).
3. Turn off tool and allow to cool.
Press reset button on tool.
4. Internal damage or
wear. (Carbon brushes or
switch, for example.)
4. Have technician service tool.
Tool operates slowly. Extension cord too long or
wire size too small.
Eliminate use of extension cord. If an extension
cord is needed, use shorter/heavier gauge cord.
See Extension Cords in GROUNDING section.
1. Keep cutting accessories sharp.
Performance
1. Accessory dull or damaged.
decreases over time.
Replace as needed.
2. Carbon brushes worn
2. Have qualified technician replace brushes.
or damaged.
Excessive noise
or rattling.
Overheating.
Internal damage or wear. (Carbon
brushes or bearings, for example.)
1. Forcing tool to work too fast.
Have technician service tool.
1. Allow tool to work at its own rate.
2. Accessory misaligned.
2. Check and correct accessory to
fence and/or table alignment.
3. Accessory dull or damaged.
4. Blocked motor housing vents.
3. Keep cutting accessories sharp.
Replace as needed.
4. Wear ANSI-approved safety goggles and NIOSH-
approved dust mask/respirator while blowing
dust out of motor using compressed air.
5. Motor being strained by long or
small diameter extension cord.
5. Eliminate use of extension cord. If an
extension cord is needed, use one with the
proper diameter for its length and load. See
Extension Cords in GROUNDING section.
Follow all safety precautions whenever diagnosing or servicing
the tool. Disconnect power supply before service.
SKU 68148
For technical questions, please call 1‑800‑444‑3353.
Page 11
PARTS LIST
Part
1
Description
Rubber Ring
Qty
1
Part
32
Description
Front Cover
Steel Ball (Ø8)
Compress Spring
Chuck
Qty
Part
63
64
65
66
67
68
69
74
75
76
77
78
Description
Side Handle Base
Handle Nut
Side Handle Clamp
Insulating Washer
Support
Qty
1
1
6
1
1
1
1
2
Hex Socket
Bolt (M6X25)
4
33
1
34
1
3
4
5
6
7
9
Cylinder Cover
O-Ring (Ø44xØ2)
Impact Piston
O-Ring (Ø24xØ3)
Cylinder
1
1
1
1
1
4
35
2
36
Ball Press
1
37
Retaining
Ring (Ø28)
Rivet
4
Trigger
1
38
39
Seal Ring
1
1
Main Handle
Cord Protector
Cord
1
Spring Washer
(Ø3)
O-Ring
(Ø31.5xØ2)
1
1
10
Press Piston
1
1
1
40
41
42
43
44
45
46
47
Ball Bearing (6201)
Dust Seal
1
1
1
1
1
2
1
2
Cord Clip
1
10A O-Ring (Ø22xØ4)
Hex Socket Bolt
(M6x50)
4
10B O-Ring
Armature
(Ø24xØ1.8)
Insulation Washer
Ball Bearing (608)
Brush Terminal
Fan Guide
78A Spring Washer
8
4
11
12
13
Steel Pin
1
1
1
(Ø6)
Oil Tank Cover
78B Flat Washer
O-Ring
(Ø55xØ2.5)
(Ø6x (Ø10.5)
79
90
Main Handle Cover
1
1
Tapping Screw
(ST4.8x58)
14
15
Connecting Rod
1
1
Hex Bar Wrench
(5mm)
Needle Bearing
(HK 12/12-1)
48
49
50
51
Stator
1
2
1
2
2
2
2
4
91
92
Tank Cover Wrench
1
1
Flat Washer (Ø5)
Housing
16
17
18
Crank Shaft
Key (4x13)
1
2
1
Oil Bottle
Carbon Brush
Retaining
Ring (Ø47)
51B Brush Holder
52
53
Brush Cap
19
20
Ball Bearing (6303)
1
1
Rubber Cap
O-Ring
(Ø46.5xØ2)
54A Machine Screw
(M4x8)
21
22
Gear Box
1
1
54
Carbon Brush
Cover
2
Oil Seal Ring
(Ø18xØ30x6)
55
56
57
58
59
60
Insulator
Stator
1
1
1
1
4
4
23
24
25
26
27
Gear
1
1
1
1
1
Inner Cover
Sensor
Ball Bearing (6001)
Impact Block Ring
Capacitor
Connector
Needle Bearing
(BK1312)
Hex Socket
Bolt (M6x20)
28
29
Impact Hammer
1
1
61
Tapping Screw
(ST4.2x18)
3
2
1
L-Ring
(Ø27xØ36x6.5)
61A Tapping Screw
(ST4.2x22)
30
31
O-Ring
(Ø26.4xØ3.5)
1
1
62
Side Handle
O-Ring (Ø38xØ2)
Page 12
For technical questions, please call 1‑800‑444‑3353.
SKU 68148
ASSEMBLY DIAGRAM
SKU 68148
For technical questions, please call 1‑800‑444‑3353.
Page 13
LIMITED 90 DAY WARRANTY
Harbor Freight Tools Co. makes every effort to assure that its products meet high quality
and durability standards, and warrants to the original purchaser that this product is free from
defects in materials and workmanship for the period of 90 days from the date of purchase. This
warranty does not apply to damage due directly or indirectly, to misuse, abuse, negligence or
accidents, repairs or alterations outside our facilities, criminal activity, improper installation,
normal wear and tear, or to lack of maintenance. We shall in no event be liable for death,
injuries to persons or property, or for incidental, contingent, special or consequential damages
arising from the use of our product. Some states do not allow the exclusion or limitation of
incidental or consequential damages, so the above limitation of exclusion may not apply to
you. THIS WARRANTY IS EXPRESSLY IN LIEU OF ALL OTHER WARRANTIES, EXPRESS
OR IMPLIED, INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS.
To take advantage of this warranty, the product or part must be returned to us with
transportation charges prepaid. Proof of purchase date and an explanation of the complaint
must accompany the merchandise. If our inspection verifies the defect, we will either repair
or replace the product at our election or we may elect to refund the purchase price if we
cannot readily and quickly provide you with a replacement. We will return repaired products
at our expense, but if we determine there is no defect, or that the defect resulted from causes
not within the scope of our warranty, then you must bear the cost of returning the product.
This warranty gives you specific legal rights and you may
also have other rights which vary from state to state.
3491 Mission Oaks Blvd. • PO Box 6009 • Camarillo, CA 93011 • (800) 444-3353
Record Product’s Serial Number Here:
Note: If product has no serial number, record month and year of purchase instead.
Note: Some parts are listed and shown for illustration purposes only,
and are not available individually as replacement parts.
PLEASE READ THE FOLLOWING CAREFULLY
THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND ASSEMBLY DIAGRAM
IN THIS MANUALASAREFERENCE TOOL ONLY. NEITHER THE MANUFACTURER OR DISTRIBUTOR MAKES
ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS QUALIFIED TO
MAKE ANY REPAIRS TO THE PRODUCT, OR THAT HE OR SHE IS QUALIFIED TO REPLACE ANY PARTS
OF THE PRODUCT. IN FACT, THE MANUFACTURER AND/OR DISTRIBUTOR EXPRESSLY STATES THAT
ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN BY CERTIFIED AND LICENSED
TECHNICIANS, AND NOT BY THE BUYER. THE BUYER ASSUMES ALL RISK AND LIABILITY ARISING OUT
OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS THERETO, OR ARISING
OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO.
Page 14
For technical questions, please call 1‑800‑444‑3353.
SKU 68148
|