digital scale
Model 95364
asseMbly and Operating instructiOns
read this material before using this product.
Failure to do so can result in serious injury.
saVe this Manual.
Copyright© 2006 by Harbor Freight Tools®. All rights reserved. No portion of this manual or any artwork
contained herein may be reproduced in any shape or form without the express written consent of Harbor Freight
Tools. Diagrams within this manual may not be drawn proportionally. Due to continuing improvements, actual
product may differ slightly from the product described herein. Tools required for assembly and service may not
be included.
For technical questions or replacement parts, please call 1-800-444-3353.
Revised Manual 10j
Warning:
The warnings, cautions, and instructions discussed in this manual cannot cover all
conditions and situations that may occur. Common sense and caution are factors
which cannot be built into this product, but must be supplied by the operator.
Unpacking and Assembly
When unpacking your Digital Scale, check to make sure that the product is intact and undamaged.
If any parts are missing or broken, please call HARBOR FREIGHT TOOLS at: 1-800-444-3353.
Your Digital Scale requires no assembly. It is important that you read the entire manual to become
familiar with the product BEFORE you use the Digital Scale.
Place the Scale in a sheltered area when in use as air movement and breathing on the scale
will affect accuracy. Always place objects on the platform gently.
Installing and Replacing Batteries
1.
2.
3.
Turn the Scale on its side. Remove the battery compartment cover by pressing the tab
towards the cover and lifting it off.
Insert four 1.5V “AA” batteries into the battery compartment. Be sure to align batteries with
the corresponding polarity.
Replace the battery compartment cover.
Using the Adaptor
Your Digital Scale can also be operated with the AC Adaptor that is included with the Digital Scale.
1.
2.
Connect the Adapter plug to the receptacle located at the rear of the Digital Scale.
Plug the Adapter into the wall outlet. The Digital Scale is ready for operation.
Operation
1.
2.
Place the Digital Scale on a flat surface in the work area.
Press the ON/TARE switch once. The Scale will start operating. When “0” “and” “ 0 ”
appear on the digital display, the Scale is ready for weighing.
3.
4.
Gently place the item to be weighed on the platform. The weight will appear on the display.
When weighing substances that must be put into a container (such as powders or liquids),
place the empty container on the Scale platform. Press the ON/TARE switch. The digital
display will return to zero, eliminating the weight of the container. A “ 0 ” readout will
appear in the lower left corner of the display.
5.
6.
Pour the powder or liquid in the container. The weight of the substance will appear on the
digital display.
To turn off the Scale, press the OFF switch. The Scale is also equipped with an auto shut-off
function. The scale will automatically turn off 40 seconds after an item is weighed.
Rev 07k
SKU 95364
For technical questions please call 1-800-444-3353.
Page 3
Changing Weight Unit
You can change the Digital Scale’s weight unit from “g” (grams) to “oz” (ounces) to “lb” (pounds).
1.
2.
When turning on the Digital Scale, the default weight unit is always “g” (grams).
When there is no item on the platform, the “g” indicator on the upper right corner of the
digital display will light on and point to “g”.
3.
Press the MODE switch to change the weight unit from “g” to “oz” or to “lb”.
Examples:
If weighing an item less than 454 grams (such as 387 g) then 387 g will appear in “g”
mode. 13.65 oz. will appear when switching to “oz” (or ounce) mode. And .852 lb.
will appear when switching to “lb” (or pound) mode.
If weighing an item more than 454 grams (such as 1326 g.) then 1326 g will appear in “g”
mode. 46.75 oz. will appear in “oz” mode. And 2.922 lb. will appear in “lb” mode.
Calibrating the Scale
1.
2.
3.
To Calibrate, or balance, the Scale, press the CAL button for three seconds. Once the
display shows “CAL”, stop pressing the button.
Press the CAL button again. Place an item that weighs 5.5 lb. (2500 G) on the scale. Press
the CAL button again. The display will show “0”. Keep the item on the platform.
Place another item weighing 5.5 lb. on the platform. Press the CAL button again. The
display will show “ACC”, meaning the Scale is successfully calibrated.
Maintenance
1.
2.
Protect Scale from rough use; it is susceptible to damage from being dropped or other
abuse.
Protect the Scale from exposure to water or corrosive materials. It should be kept clean and
dry. Occasional cleaning with a clean rag will extend its life and good appearance.
3.
4.
Store in a dry location to inhibit rust. Keep out of the reach of children.
To remove the platform for easy cleaning: Rotate the table slightly to align its tabs to the
notches on the mount below, and lift the platform free.
Rev 07k, 08b
SKU 95364
For technical questions please call 1-800-444-3353.
Page 4
Troubleshooting
1.
2.
Digital display flashes “LO”: Battery charge is low. Please replace battery or use Adaptor.
Display doesn’t change when buttons are pushed: Circuit needs to be reset. Remove
the battery, wait 30 seconds, replace battery and turn the Scale “ON”.
3.
Display does not show: Battery has poor connection or battery voltage is to low. Take
battery out and adjust connections. Replace the battery as necessary or use Adaptor.
No replacement parts are available for this product.
PLEASE READ THE FOLLOWING CAREFULLY
THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS DIAGRAM IN THIS MANUAL AS A REFERENCE TOOL ONLY. NEITHER
THE MANUFACTURER NOR DISTRIBUTOR MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS
QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT OR THAT HE OR SHE IS QUALIFIED TO REPLACE ANY PARTS OF THE PRODUCT. IN FACT,
THE MANUFACTURER AND/OR DISTRIBUTOR EXPRESSLY STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN
BY CERTIFIED AND LICENSED TECHNICIANS AND NOT BY THE BUYER. THE BUYER ASSUMES ALL RISK AND LIABILITY ARISING OUT OF HIS
OR HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS THERETO, OR ARISING OUT OF HIS OR HER INSTALLATION OF
REPLACEMENT PARTS THERETO.
liMited 90 day Warranty
Harbor Freight Tools Co. makes every effort to assure that its products meet high quality and
durability standards, and warrants to the original purchaser that this product is free from defects in
materials and workmanship for the period of 90 days from the date of purchase. This warranty does
not apply to damage due directly or indirectly, to misuse, abuse, negligence or accidents, repairs or
alterations outside our facilities, criminal activity, improper installation, normal wear and tear, or to
lack of maintenance. We shall in no event be liable for death, injuries to persons or property, or for
incidental, contingent, special or consequential damages arising from the use of our product. Some
states do not allow the exclusion or limitation of incidental or consequential damages, so the above
limitation of exclusion may not apply to you. THiS WARRANTy iS expReSSly iN lieu oF All
oTHeR WARRANTieS, expReSS oR iMplieD, iNCluDiNg THe WARRANTieS oF MeRCHANT-
AbiliTy AND FiTNeSS.
To take advantage of this warranty, the product or part must be returned to us with transporta-
tion charges prepaid. proof of purchase date and an explanation of the complaint must accompany
the merchandise. If our inspection verifies the defect, we will either repair or replace the product at
our election or we may elect to refund the purchase price if we cannot readily and quickly provide you
with a replacement. We will return repaired products at our expense, but if we determine there is no
defect, or that the defect resulted from causes not within the scope of our warranty, then you must
bear the cost of returning the product.
This warranty gives you specific legal rights and you may also have other rights which vary
from state to state.
3491 Mission Oaks Blvd. • PO Box 6009 • Camarillo, CA 93011 • (800) 444-3353
Rev 07k
SKU 95364
For technical questions please call 1-800-444-3353.
Page 5
|