MASTER BALL JOINT ADAPTER / 14 PC
(FOR USE WITH 3-IN-1 SERVICE KIT - MODEL 38335)
Model 46389
OPERATING INFORMATION
®
3491 Mission Oaks Blvd., Camarillo, CA 93011
Copyright
2001 by Harbor Freight Tools. All rights reserved. No portion of this
manual or any artwork contained herein may be reproduced in any shape or form
without the express written consent of Harbor Freight Tools.
For technical questions please call 1-800-444-3353
2.
3.
KEEP CHILDREN AWAY FROM WORK AREA. Do not allow children to handle
this product.
STORE IDLE EQUIPMENT. When not in use, tools and equipment should be
stored in a dry location to inhibit rust. Always lock up tools and equipment and
keep out of reach of children.
4.
DO NOT USE THIS PRODUCT IF UNDER THE INFLUENCE OF ALCOHOL OR
DRUGS. Read warning labels on prescriptions to determine if your judgment or
reflexes are impaired while taking drugs. If there is any doubt, do not attempt to
use this product.
5.
6.
USE EYE PROTECTION. Wear ANSI approved safety impact eye glasses when
using this product. ANSI approved safety impact eye glasses are available from
Harbor Freight Tools.
DRESS SAFELY. Non-skid footwear or safety shoes should be used when
working with this product. Do not wear loose clothing or jewelry as they can
become caught in moving parts. Wear a protective hair covering to prevent long
hair from becoming caught in moving parts. If wearing a long-sleeve shirt, roll
sleeves up above elbows.
7.
8.
INDUSTRIAL APPLICATIONS MUST FOLLOW OSHA REQUIREMENTS.
DO NOT OVERREACH. Keep proper footing and balance at all times to prevent
tripping, falling, back injury, etcetera.
9.
STAY ALERT. Watch what you are doing at all times. Use common sense. Do
not use this product when you are tired or distracted from the job at hand.
10.
CHECK FOR DAMAGED PARTS. Before using this product, carefully check that
it will operate properly and perform its intended function. Check for damaged
parts and any other conditions that may affect the operation of this product.
Replace or repair damaged or worn parts immediately.
11.
REPLACEMENT PARTS AND ACCESSORIES. When servicing, use only
identical replacement parts. Only use accessories intended for use with this
product. Approved accessories are available from Harbor Freight Tools.
12.
13.
MAINTAIN THIS PRODUCT WITH CARE. Keep this tool clean and dry for better
and safer performance.
MAINTENANCE: For your safety, service and maintenance should be performed
regularly by a qualified technician.
SKU 46389
PAGE 3
14.
USE THE RIGHT PRODUCT FOR THE RIGHT JOB. There are certain
applications for which this product was designed. Do not use small equipment,
tools or attachments to do the work of larger industrial equipment, tools or
attachments. Do not use this product for a purpose for which it was not intended.
15.
16.
PRIOR TO USING THIS PRODUCT, MAKE SURE TO READ AND
UNDERSTAND ALL INSTRUCTIONS AND SAFETY PRECAUTIONS AS
OUTLINED IN THE VEHICLES MANUFACTURER’S MANUALS.
NEVER WORK UNDERNEATH A VEHICLE WITHOUT USING ADDITIONAL
SAFETY SUPPORT DEVICES (I.E., JACK STANDS) TO SUPPORT THE
WEIGHT OF THE VEHICLE. Read and understand all safety warnings and
instructions provided in the instruction manual of the vehicle as well as the jack
stand being used to support the vehicle.
17.
WARNING: This product contains or produces a chemical known to the State of
California to cause cancer and birth defects (or other reproductive harm).
(California Health & Safety Code 25249.5 et seq.)
UNPACKING
When unpacking, check to make sure the parts shown on page 10 of this manual are
included. If any parts are missing or broken, please call Harbor Freight Tools at the
number shown on the cover of this manual as soon as possible.
OPERATING INSTRUCTIONS
Note: All parts mentioned below refer to the parts listed and shown on
page 10 of this manual.
NOTE: This Master Ball Joint Adapter Set is intended for use with the
3-In-1 Service Kit (Model 38335), which is available from Harbor Freight
Tools. Read and understand all safety warnings and instructions provided in the
instruction manual of the 3-In-1 Service Kit before using the kit.
To Attach The Plug Bolt To The C-Frame:
1.
The illustration on the following page depicts a disassembled C-Frame, a tool that
is part of the 3-In-1 Service Kit (Model 38335) and intended for use with this
Master Ball Joint Adapter Set. (See Figure A.)
SKU 46389
PAGE 4
O-RING
(NOT PROVIDED)
STEEL BALL
(NOT PROVIDED)
FORCING
SCREW
(NOT PROVIDED)
PLUG BOLT (#14)
C-FRAME (NOT PROVIDED)
FIGURE A
2.
To operate the Master Ball Joint Adapter Set, it will be necessary to attach the
Plug Bolt (part #14) contained in this Set to the C-Frame of the 3-In-1 Service Kit.
(See Figure A, and Assy. Diagram.)
3.
4.
5.
To do so, unscrew and remove the Forcing Screw, Steel Ball, and O-Ring from
the C-Frame. (See Figure A, and Assy. Diagram.)
Make sure the Steel Ball and O-Ring remain inside the Forcing Screw. Then,
insert the Plug Bolt (part #14) into the Forcing Screw.
Screw the threaded end of the Forcing Screw, with its Steel Ball, O-Ring, and
attached Plug Bolt (part #14) back into the threaded end of the C-Frame toward
the unthreaded hole of the C-Frame. (See Figure A, and Assy. Diagram.)
To Remove A Ball Joint:
1.
NOTE: The following instructions apply to most GM, Ford, and Dodge 2 and 4
wheel drive pickups, vans, and SUV’s through 1997 (see charts on pages 7
through 9). The instructions are intended to illustrate the process in general
terms, not to be specific to any one make/model vehicle. A combination of Re-
ceiving Tubes (parts #1, #2, #3, #4, #5, #6, #10, #11), Receiving Cups (parts #7,
#12), and Installing Tubes (parts #8, #9), will be necessary for different vehicles.
2.
3.
Remove all attaching hardware from the ball joint.
Mount the Remover/Installer (part #13) on the Forcing Screw assembly so that
the larger diameter portion of the Remover/Installer faces the threaded hole of
the C-Frame, and the smaller diameter portion faces the unthreaded side of the
ball joint. (See Figure B, and Assy. Diagram.)
SKU 46389
PAGE 5
RECEIVER TUBE (#1, #2, #3, #4, #5, #6, #10, #11)
REMOVER/INSTALLER
(#13)
C-FRAME
PLUG BOLT (#14)
FORCING SCREW
FIGURE B
4.
5.
6.
Mount the proper size Receiver Tube (parts #1, #2, #3, #4, #5, #6, #10, #11) over
the threaded side of the ball joint. (See Figure B, and Assy. Diagram.)
Align the mounted Remover/Installer (part #13), ball joint, and Reciever Tube
(parts #1, #2, #3, #4, #5, #6, #10, #11) to allow removal of the ball joint.
Using a wrench, turn the Forcing Screw assembly clockwise to remove the ball
joint.
To Install A Ball Joint:
1.
Mount the Remover/Installer (part #13) on the Forcing Screw assembly so that
the larger diameter portion of the Remover/Installer faces the threaded hole of
the C-Frame, and the smaller diameter portion faces the unthreaded side of the
ball joint. (See Figure B, and Assy. Diagram.)
2.
3.
Place the mounted Remover/Installer (part #13) on the unthreaded side of the
ball joint. (See Figure B, and Assy. Diagram.)
Align the mounted Remover/Installer (part #13), ball joint, and proper size
Reciever Tube (parts #1, #2, #3, #4, #5, #6, #10, #11) to allow installation of the
ball joint. (See Figure B, and Assy. Diagram.)
4.
Using a wrench, turn the Forcing Screw assembly clockwise to install the ball
joint. (See Figure B, and Assy. Diagram.)
SKU 46389
PAGE 6
BALL JOINT ADAPTER APPLICATIONS CHART
ꢀꢁꢂꢁꢀꢃ ꢄꢅꢃꢁꢁꢁꢁꢁꢁꢁꢁꢁꢁꢁꢁꢁꢁꢁꢁꢁꢁꢁꢁꢁꢁꢁꢁꢆꢂꢁꢆꢇꢈꢉꢊꢋꢋ
ꢌꢍꢎꢏꢐꢁꢑꢒꢓꢔꢕꢁꢖꢗꢘꢀꢙꢁꢚꢛꢌꢜꢏꢀꢝꢁꢜꢏꢐꢍ!ꢁꢝ"ꢍ!ꢚꢁꢍꢚꢁꢗꢘ$ꢏꢁ%&'
ꢜꢊꢋꢋ
*ꢄꢞꢇꢉ
%&
ꢔ
X
%
Y
Z
ꢕ
%Y %ꢓ
ꢑ
ꢓ
ꢒ
%%
%
ꢑ
ꢛꢟꢟꢃꢠ=
ꢐꢄꢡꢃꢠ
?ꢃꢢꢞQꢋꢃ
ꢀꢁꢀꢂꢃꢄꢅꢄꢆꢇꢈꢉꢊꢋꢃꢈꢄꢅꢄꢌꢋꢉꢍꢁꢎꢏꢇ
%ꢕꢔX[ꢕXꢁꢎꢊꢣꢄꢉꢊꢁY!ꢎ
ꢐꢄꢡꢃꢠ
%ꢕXY[ꢕꢓꢁ%=Y[]ꢁꢓ=ꢑ[ꢉꢄꢇꢁY!ꢎꢁꢗꢞQꢣꢤꢟ
%ꢕXꢑ[ꢕꢓꢁ%=Y[ꢁꢉꢄꢇꢁY!ꢎꢁꢀꢊ Qꢢꢊꢠꢥꢃꢠ
%ꢕXꢕ[ꢕXꢁ%=Y[]ꢁꢓ=ꢑ[]ꢁ%[ꢉꢄꢇꢁY!ꢎꢁꢅꢊꢇ
%ꢕXY[ꢕꢓꢁꢓ=ꢑ[]ꢁ%[ꢉꢄꢇꢁY!ꢎꢁꢗꢞQꢣꢤꢟ
%ꢕXꢕ[ꢕXꢁ%[ꢉꢄꢇꢁY!ꢎꢁꢅꢊꢇ
ꢆ
ꢀꢆ
ꢀ
ꢐꢄꢡꢃꢠ
ꢐꢄꢡꢃꢠ
ꢛꢟꢟꢃꢠ
ꢐꢄꢡꢃꢠ
ꢛꢟꢟꢃꢠ
ꢐꢄꢡꢃꢠ
ꢐꢄꢡꢃꢠ
ꢀ
ꢀ
ꢆ
%ꢕꢔꢑ[ꢕꢒꢁ`ꢊꢠꢊꢅꢊꢇ]ꢁ?ꢄꢦꢊꢥꢃꢠ]
ꢙꢄꢡꢇꢁ|ꢁ`ꢄꢤꢇꢉꢠꢦ
%ꢕꢕꢑꢁ[ꢁꢕXꢁ%=Y[]ꢁꢓ=ꢑ[]ꢁ%[ꢉꢄꢇ
Y!ꢎꢁꢗꢞQꢣꢤꢟꢁꢖꢆ}ꢝ'
ꢆ
ꢆ
%ꢕꢕꢑ[ꢕXꢁ%=Y[]ꢁꢓ=ꢑ[]ꢁ%[ꢉꢄꢇ
Y!ꢎꢁꢗꢞQꢣꢤꢟꢁꢖꢆ}ꢝ'
ꢆ
ꢆ
%ꢕꢕꢑ[ꢕXꢁ%[ꢉꢄꢇꢁꢈꢄꢋꢞ~ꢁꢊꢧꢋꢃ]ꢁY!ꢎ€
ꢓ=ꢑ]ꢁꢁ%[ꢉꢄꢇꢁꢎꢊꢇꢊꢁꢒ&ꢁꢊꢧꢋꢃ]ꢁꢑ!ꢎ
ꢆ
%ꢕꢕꢑ[ꢕXꢁ%[ꢉꢄꢇꢁꢈꢄꢋꢞ~ꢁꢊꢧꢋꢃ]ꢁY!ꢎ€
ꢓ=ꢑ[]ꢁ%[ꢉꢄꢇꢁꢎꢊꢇꢊꢁꢒ&ꢁꢊꢧꢋꢃ]ꢁꢑ!ꢎ
ꢆ
ꢀꢆ
%ꢕꢕꢑ[ꢕXꢁ%=Y[]ꢁꢓ=ꢑ[ꢁꢎꢊꢇꢊꢁꢑꢑ
ꢊꢧꢋꢃ]ꢁꢑ!ꢎ
ꢀ
ꢀ
ꢆ
ꢆ
ꢆ
ꢆ
ꢀ
ꢀ
%ꢕXY[ꢕꢓꢁ%=Y[]ꢁꢓ=ꢑ[]ꢁ%[ꢉꢄꢇꢁꢑ!ꢎ
|ꢁꢀꢊ Qꢢꢊꢠꢥꢃꢠ
%ꢕꢕꢑ[ꢕXꢁ%=Y[]ꢁꢓ=ꢑ[ꢉꢄꢇꢁꢎꢊꢇꢊꢁꢑꢑ
ꢊꢧꢋꢃ]ꢁꢑ!ꢎ
ꢛꢟꢟꢃꢠ
ꢛꢟꢟꢃꢠ
%ꢕXY[ꢕꢓꢁ%=Y[]ꢁꢓ=ꢑ[]ꢁ%[ꢉꢄꢇ
ꢑ!ꢎꢁ|ꢁꢀꢊ Qꢢꢊꢠꢥꢃꢠ
ꢀ
ꢆ
ꢆ
ꢐꢃꢃꢌ
ꢛꢟꢟꢃꢠ
%ꢕꢕꢓ[ꢕXꢁY!ꢎꢁ$ꢠꢊꢇ~ꢁ`ꢢꢃꢠꢄꢣꢃꢃ
%ꢕꢕꢓ[ꢕZꢁꢑ!ꢎꢁ$ꢠꢊꢇ~ꢁ`ꢢꢃꢠꢄꢣꢃꢃ
$ꢠꢊꢇ~ꢁ!ꢊꢥꢄꢇꢃꢃꢠ
ꢀ
ꢀ
ꢆ
ꢆ
ꢆ
ꢆ
ꢀ
ꢀ
%ꢕꢔX[ꢕXꢁꢑ!ꢎꢁ!ꢠꢊꢇꢥꢋꢃꢠ
%ꢕꢔꢑ[ꢕZꢁꢑ!ꢎꢁ!ꢊꢥꢄꢇꢃꢃꢠ]ꢁ`ꢢꢃꢠꢄꢣꢃꢃ
ꢐꢄꢡꢃꢠ
%ꢕꢕꢓ[ꢕXꢁY!ꢎꢁ$ꢠꢊꢇ~ꢁ`ꢢꢃꢠꢄꢣꢃꢃ
%ꢕꢕ&[ꢕXꢁY!ꢎꢁ`ꢢꢃꢠꢄꢣꢃꢃ]ꢁ!ꢊꢥꢄꢇꢃꢃꢠ]
`ꢄ ꢊꢇQꢢꢃ
%ꢕꢕꢓ[ꢕZꢁꢑ!ꢎꢁ$ꢠꢊꢇ~ꢁ`ꢢꢃꢠꢄꢣꢃꢃ]
$ꢠꢊꢇ~ꢁ!ꢊꢥꢄꢇꢃꢃꢠ
%ꢕꢕ&[ꢕXꢁꢑ!ꢎꢁ!ꢠꢊꢇꢥꢋꢃꢠ
%ꢕꢕ&[ꢕZꢁY!ꢎꢁ|ꢑ!ꢎꢁ!ꢊꢥꢄꢇꢃꢃꢠ]
`ꢄ ꢊꢇQꢢꢃ]ꢁ`ꢢꢃꢠꢄꢣꢃꢃ
ꢛꢟꢟꢃꢠ
ꢐꢄꢡꢃꢠ
%ꢕꢔꢑ[ꢕXꢁY!ꢎꢁ`ꢢꢃꢠꢄꢣꢃꢃ]ꢁ!ꢊꢥꢄꢇꢃꢃꢠ]
`ꢄ ꢊꢇQꢢꢃ
ꢀ
ꢀ
ꢆ
ꢆ
ꢆ
ꢆ
ꢀ
ꢆ
%ꢕꢔꢑ[ꢔꢕꢁY!ꢎꢁ`ꢢꢃꢠꢄꢣꢃꢃ]ꢁ!ꢊꢥꢄꢇꢃꢃꢠ
`ꢄ ꢊꢇQꢢꢃ
%ꢕꢔX[ꢔꢕꢁꢑ!ꢎꢁ!ꢠꢊꢇꢥꢋꢃꢠ
ꢀ
%ꢕꢔꢑ[ꢔꢕꢁꢑ!ꢎꢁ!ꢊꢥꢄꢇꢃꢃꢠ]ꢁ`ꢄ ꢊꢇQꢢꢃ
ꢛꢟꢟꢃꢠ
ꢐꢄꢡꢃꢠ
%ꢕꢔꢑ[ꢕYꢁꢨꢤꢋꢋꢁꢈꢞꢩꢃꢁꢑ!ꢎꢁ$ꢠꢊꢇ~
!ꢊꢥꢄꢇꢃꢃꢠ
ꢀ
ꢀ
ꢆ
ꢆ
ꢆ
ꢆ
%ꢕXY[ꢔꢔꢁꢑ!ꢎꢁꢙꢠꢤQꢣ]ꢁ`*]ꢁꢨꢤꢋꢋꢁꢈꢞꢩꢃ
`ꢢꢃꢠꢄꢣꢃꢃ]ꢁ!ꢊꢥꢄꢇꢃꢃꢠ
%ꢕꢔꢑ[ꢕYꢁꢨꢤꢋꢋꢁꢈꢞꢩꢃꢁꢑ!ꢎꢁ$ꢠꢊꢇ~
!ꢊꢥꢄꢇꢃꢃꢠ
%ꢕXY[ꢔꢔꢁꢑ!ꢎꢁꢙꢠꢤQꢣ]ꢁ`*]ꢁꢨꢤꢋꢋꢁꢈꢞꢩꢃ
`ꢢꢃꢠꢄꢣꢃꢃ]ꢁ!ꢊꢥꢄꢇꢃꢃꢠ
SKU 46389
PAGE 7
BALL JOINT
ADAPTER APPLICATIONS CHART
ꢀꢁꢂꢁꢀꢃ ꢄꢅꢃꢁꢁꢁꢁꢁꢁꢁꢁꢁꢁꢁꢁꢁꢁꢁꢁꢁꢁꢁꢁꢁꢁꢁꢁꢆꢂꢁꢆꢇꢈꢉꢊꢋꢋ
ꢌꢍꢎꢏꢐꢁꢑꢒꢓꢔꢕꢁꢖꢗꢘꢀꢙꢁꢚꢛꢌꢜꢏꢀꢝꢁꢝ"ꢍ!ꢚꢁꢜꢏꢐꢍ!ꢁꢍꢚꢁꢗꢘ$ꢏꢁ%&'
ꢜꢊꢋꢋ
*ꢄꢞꢇꢉ
ꢛꢟꢟꢃꢠ
ꢐꢄꢡꢃꢠ
%&
ꢔ
X
%
Y
Z
ꢕ
%Y %ꢓ
ꢑ
ꢓ
ꢒ
%%
%
ꢑ
?ꢃꢢꢞQꢋꢃ
ꢑꢁꢈꢀ
ꢐꢄꢡꢃꢠ
ꢛꢟꢟꢃꢠ
%ꢕꢔꢒ[ꢕXꢁꢘꢃꢠꢄꢈꢉꢊꢠ
ꢆ
ꢆ
%ꢕꢔꢕ[ꢕ&ꢁY!ꢎꢁꢜꢠꢄꢇQꢄꢁꢆꢆ
%ꢕꢕ%[ꢕꢑꢁY!ꢎꢁꢏꢧꢟꢋꢄꢠꢃꢠ
%ꢕꢔꢕ[ꢕX Y!ꢎ ꢀꢊꢇꢥꢃꢠ
%ꢕꢔX[ꢔꢔꢁY!ꢎꢁꢜꢠꢄꢇQꢄꢁꢆꢆ
ꢆ
ꢛꢟꢟꢃꢠ
ꢐꢄꢡꢃꢠ
ꢆ
ꢆ
ꢆ
%ꢕꢔꢓ[ꢔꢔꢁY!ꢎꢁꢀꢊꢇꢥꢃꢠ
%ꢕꢔꢕ[ꢕ&ꢁY!ꢎꢁꢜꢠꢄꢇQꢄꢁꢆꢆ
%ꢕꢕ%[ꢕꢑꢁY!ꢎꢁꢏꢧꢟꢋꢄꢠꢃꢠ
%ꢕꢔꢕ[ꢕXꢁY!ꢎꢁꢀꢊꢇꢥꢃꢠ
ꢐꢄꢡꢃꢠ
ꢁ%ꢕꢔX[ꢔꢔꢁY!ꢎꢁꢜꢠꢄꢇQꢄꢁꢆꢆ
%ꢕꢔꢓ[ꢔꢔꢁY!ꢎꢁꢀꢊꢇꢥꢃꢠ
ꢆ
ꢆ
ꢀ
ꢀ
ꢀ
ꢀ
ꢐꢄꢡꢃꢠ
ꢛꢟꢟꢃꢠ
%ꢕꢕXꢁ%=Y[ꢉꢄꢇꢁꢗꢞQꢣꢤꢟ]ꢁY!ꢎꢁ|ꢁꢑ!ꢎ
ꢆ
ꢀ
ꢆ
%ꢕꢔX[ꢕꢒꢁ%=Y[ꢉꢄꢇꢁY!ꢎꢁꢗꢞQꢣꢤꢟ
%ꢕꢔX[ꢕXꢁꢓ=ꢑ[]ꢁ%[ꢉꢄꢇꢁY!ꢎꢁꢗꢞQꢣꢤꢟ
ꢆ
ꢆ
ꢐꢄꢡꢃꢠ
ꢛꢟꢟꢃꢠ
%ꢕꢔX[ꢕꢒꢁ%=Y[ꢉꢄꢇꢁY!ꢎꢁꢗꢞQꢣꢤꢟ
%ꢕꢔ%[ꢔꢒꢁ%=Y[ꢉꢄꢇꢁY!ꢎꢁꢗꢞQꢣꢤꢟ
%ꢕꢕ&ꢁꢑ!ꢎꢁꢜꢠꢄꢇQꢄꢁꢆꢆꢁꢡ=ꢎꢊꢇꢊꢁYꢔ
%ꢕꢔꢑ[ꢔꢕꢁꢑ!ꢎꢁꢜꢠꢄꢇQꢄꢁꢆꢆ
%ꢕꢕ%[ꢕꢑꢁꢑ!ꢎꢁꢏꢧꢟꢋꢄꢠꢃꢠꢁꢡ=ꢎꢊꢇꢊꢁYꢔ
%ꢕꢕ%[ꢕXꢁꢑ!ꢎꢁꢀꢊꢇꢥꢃꢠꢁꢡ=ꢎꢊꢇꢊꢁYꢔ
%ꢕꢔꢓ[ꢔꢕꢁꢑ!ꢎꢁꢀꢊꢇꢥꢃꢠ
ꢐꢄꢡꢃꢠ
%ꢕꢔ%[ꢔꢒꢁ%=Y[ꢉꢄꢇꢁY!ꢎꢁꢗꢞQꢣꢤꢟ
%ꢕꢔ&[ꢕꢒꢁꢑ!ꢎꢁꢜꢠꢄꢇQꢄ
%ꢕꢔ%ꢁ%[ꢉꢄꢇꢁꢖꢓꢔ&&ꢁꢊꢧꢋꢃ'ꢁꢑ!ꢎ
%ꢕꢔ&[ꢕꢒꢁ%=Y[]ꢁꢓ=ꢑ[ꢉꢄꢇꢁꢑ!ꢎ
ꢀ
ꢆ
ꢆ
ꢆ
ꢐꢄꢡꢃꢠ
ꢛꢟꢟꢃꢠ
ꢐꢄꢡꢃꢠ
ꢐꢄꢡꢃꢠ
ꢛꢟꢟꢃꢠ
%ꢕꢔX[ꢕXꢁꢓ=ꢑ[]ꢁ%[ꢉꢄꢇꢁY!ꢎ
ꢆ
ꢆ
ꢀꢆ
%ꢕꢕY[ꢕXꢁ%=Y[]ꢁꢓ=ꢑ[]ꢁ%[ꢉꢄꢇꢁY!ꢎꢁ?ꢊꢇ
%ꢕꢕY[ꢕXꢁꢓ=ꢑ[]ꢁ%[ꢉꢄꢇꢁY!ꢎꢁ?ꢊꢇ
%ꢕꢕY[ꢕXꢁ%=Y[ꢉꢄꢇꢁY!ꢎꢁ?ꢊꢇ
ꢆ
ꢆ
ꢆ
ꢀ
ꢀ
ꢀ
ꢆ
%ꢕꢕ&ꢁꢑ!ꢎꢁꢜꢠꢄꢇQꢄꢁꢆꢆꢁꢡ=ꢎꢊꢇꢊꢁꢓZ
%ꢕꢕ%[ꢕꢓꢁꢑ!ꢎꢁꢏꢧꢟꢋꢄꢠꢃꢠꢁꢡ=ꢎꢊꢇꢊꢁꢓZ
%ꢕꢕ&[ꢕꢓꢁꢑ!ꢎꢁꢀꢊꢇꢥꢃꢠꢁY=ꢎꢊꢇꢊꢁꢓZ
ꢆ
ꢐꢄꢡꢃꢠ
%ꢕꢕ&ꢁꢑ!ꢎꢁꢜꢠꢄꢇQꢄꢁꢆꢆꢁꢡ=ꢎꢊꢇꢊꢁYꢔ
%ꢕꢔꢑ[ꢔꢕꢁꢑ!ꢎꢁꢜꢠꢄꢇQꢄꢁꢆꢆ
%ꢕꢕ&[ꢕXꢁꢑ!ꢎꢁꢏꢧꢟꢋꢄꢠꢃꢠꢁꢡ=ꢎꢊꢇꢊꢁYꢔ
%ꢕꢕ&[ꢕXꢁꢑ!ꢎꢁꢀꢊꢇꢥꢃꢠꢁꢡ=ꢎꢊꢇꢊꢁYꢔ
ꢆ
ꢆ
ꢐꢄꢡꢃꢠ
ꢛꢟꢟꢃꢠ
%ꢕꢕ&ꢁꢑ!ꢎꢁꢜꢠꢄꢇQꢄꢁꢆꢆꢁꢡ=ꢎꢊꢇꢊꢁꢓZ
%ꢕꢕ%[ꢕꢓꢁꢑ!ꢎꢁꢏꢧꢟꢋꢄꢠꢃꢠꢁꢡ=ꢎꢊꢇꢊꢁꢓZ
%ꢕꢕ&[ꢕꢓꢁꢑ!ꢎꢁꢀꢊꢇꢥꢃꢠꢁꢡ=ꢎꢊꢇꢊꢁꢓZ
%ꢕꢔ&[ꢕꢒꢁꢑ!ꢎꢁꢜꢠꢄꢇQꢄ
%ꢕꢕY[ꢕXꢁ%[ꢉꢄꢇꢁꢑ!ꢎ
%ꢕꢔ&[ꢕꢒꢁ%=Y[]ꢁꢓ=ꢑ[]ꢁ%[ꢉꢄꢇꢁꢑ!ꢎꢁꢖꢆ}ꢝ'
ꢀ
ꢆ
ꢆ
ꢛꢟꢟꢃꢠ
ꢐꢄꢡꢃꢠ
%ꢕꢕꢓ[ꢕꢑꢁꢑ!ꢎꢁꢏꢧꢟꢋꢄꢠꢃꢠꢁꢡ=ꢎꢊꢇꢊꢁꢓZ
%ꢕꢕꢓ[ꢕXꢁꢑ!ꢎꢁꢀꢊꢇꢥꢃꢠꢁꢡ=ꢎꢊꢇꢊꢁꢓZ
ꢆ
ꢆ
%ꢕꢕꢓ[ꢕꢑꢁꢑ!ꢎꢁꢏꢧꢟꢋꢄꢠꢃꢠꢁꢡ=ꢎꢊꢇꢊꢁꢓZ
%ꢕꢕꢓ[ꢕXꢁꢑ!ꢎꢁꢀꢊꢇꢥꢃꢠꢁꢡ=ꢎꢊꢇꢊꢁꢓZ
ꢐꢄꢡꢃꢠ
ꢐꢄꢡꢃꢠ
%ꢕꢕꢒ[ꢕXꢁ%[ꢉꢄꢇꢁꢑ!ꢎꢁꢡ=ꢈꢄꢋꢞ~ꢁꢊꢧꢋꢃ
%ꢕꢔ&[ꢕZꢁꢓ=ꢑ[]ꢁ%[ꢉꢄꢇꢁꢑ!ꢎꢁꢈꢟꢞꢇ~ꢋꢃ
ꢆ
ꢆ
ꢆ
ꢆ
ꢀꢆ
ꢀꢆ
SKU 46389
PAGE 8
BALL JOINT ADAPTER APPLICATIONS CHART
ꢀꢁꢂꢁꢀꢃ ꢄꢅꢃꢁꢁꢁꢁꢁꢁꢁꢁꢁꢁꢁꢁꢁꢁꢁꢁꢁꢁꢁꢁꢁꢁꢁꢁꢆꢂꢁꢆꢇꢈꢉꢊꢋꢋ
ꢌꢍꢎꢏꢐꢁꢑꢒꢓꢔꢕꢁꢖꢗꢘꢀꢙꢁꢚꢛꢌꢜꢏꢀꢝꢁꢝ"ꢍ!ꢚꢁꢜꢏꢐꢍ!ꢁꢍꢚꢁꢗꢘ$ꢏꢁ%&'
ꢜꢊꢋꢋ
*ꢄꢞꢇꢉ
ꢛꢟꢟꢃꢠ
ꢐꢄꢡꢃꢠ
%&
ꢔ
X
ꢆ
%
Y
Z
ꢕ
%Y %ꢓ
ꢑ
ꢓ
ꢒ
%%
%
ꢑ
?ꢃꢢꢞQꢋꢃ
ꢂꢍ
ꢐꢄꢡꢃꢠ
%ꢕꢔY[ꢕXꢁY!ꢎꢁꢝ[%&ꢁꢜꢋꢊꢩꢃꢠ]ꢁ*ꢞ
|ꢁꢗꢞQꢣꢤꢟ
ꢦ]
ꢆ
ꢀ
ꢐꢄꢡꢃꢠ
ꢐꢄꢡꢃꢠ
%ꢕꢕꢓ[ꢕXꢁY!ꢎꢁ%=Y[]ꢁꢓ=ꢑ[]ꢁ%[ꢉꢄꢇ
ꢗꢞQꢣꢤꢟ€ꢁꢝꢤ†ꢤꢠ†ꢊꢇ
%ꢕꢕꢒ[ꢕXꢁ%=Y[]ꢁꢓ=ꢑ[ꢉꢄꢇꢁY!ꢎꢁ$ꢁ?ꢊꢇ
%ꢕꢔꢔ[ꢕYꢁY!ꢎꢁ%=Y[]ꢁꢓ=ꢑ[]ꢁ%ꢁꢉꢄꢇ
ꢗꢞQꢣꢤꢟ€ꢁꢝꢤ†ꢤꢠ†ꢊꢇ
ꢐꢄꢡꢃꢠ
ꢐꢄꢡꢃꢠ
ꢐꢄꢡꢃꢠ
%ꢕꢔZ[ꢕXꢁꢘꢈꢉꢠꢄꢁꢝꢊꢨꢊꢠꢞꢁ?ꢊꢇ
ꢆ
ꢆ
ꢆ
%ꢕXꢓ[ꢕZꢁ%=Y[]ꢁꢓ=ꢑꢁꢉꢄꢇꢁY!ꢎꢁ$ꢁ?ꢊꢇ
%ꢕꢕꢒ[ꢕXꢁ%=Y[]ꢁꢓ=ꢑ[]ꢁ%[ꢉꢄꢇꢁꢑꢧꢑ
ꢀ
ꢆ
INSPECTION, MAINTENANCE, AND CLEANING
1.
2.
Before each use, inspect the general condition of the Master Ball Joint Adapter
set. Check for cracks , breaks, or bends in the tool, and any other condition that
may affect its safe operation. If a problem occurs with the tool, immediately
discontinue its use and have the problem corrected before further use. Do not
use damaged equipment.
To clean, wipe with a damp cloth. You may use a mild detergent or mild solvent.
PLEASE READ THE FOLLOWING CAREFULLY
THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THIS MANUAL AS A
REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER NOR DISTRIBUTOR
MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER
THAT HE OR SHE IS QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT OR
THAT HE OR SHE IS QUALIFIED TO REPLACE ANY PARTS OF THE PRODUCT. IN
FACT, THE MANUFACTURER AND/OR DISTRIBUTOR EXPRESSLY STATES THAT
ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN BY
CERTIFIED AND LICENSED TECHNICIANS AND NOT BY THE BUYER. THE BUYER
ASSUMES ALL RISK AND LIABILITY ARISING OUT OF HIS OR HER REPAIRS TO
THE ORIGINAL PRODUCT OR REPLACEMENT PARTS THERETO, OR ARISING
OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO.
SKU 46389
PAGE 9
PARTS LIST / ASSEMBLY DIAGRAM
ꢌꢒꢓꢔꢄꢕ
ꢀꢖꢗꢘꢓꢙꢚꢔꢙꢛꢜ
ꢀꢃQꢃꢞꢅꢞꢇꢥꢁꢙꢤ†ꢃ
ꢝꢔꢞ!
%
%
Y
ꢀꢃQꢃꢞꢅꢞꢇꢥꢁꢙꢤ†ꢃ
ꢀꢃQꢃꢞꢅꢞꢇꢥꢁꢙꢤ†ꢃ
ꢀꢃQꢃꢞꢅꢞꢇꢥꢁꢙꢤ†ꢃ
ꢀꢃQꢃꢞꢅꢞꢇꢥꢁꢙꢤ†ꢃ
ꢀꢃQꢃꢞꢅꢞꢇꢥꢁꢙꢤ†ꢃ
ꢀꢃQꢃꢞꢅꢞꢇꢥꢁ`ꢤꢟ
ꢆꢇꢈꢉꢊꢋꢋꢞꢇꢥꢁꢙꢤ†ꢃ
ꢆꢇꢈꢉꢊꢋꢋꢞꢇꢥꢁꢙꢤ†ꢃ
ꢀꢃQꢃꢞꢅꢞꢇꢥꢁꢙꢤ†ꢃ
ꢀꢃQꢃꢞꢅꢞꢇꢥꢁꢙꢤ†ꢃ
ꢀꢃQꢃꢞꢅꢞꢇꢥꢁ`ꢤꢟ
ꢀꢃ ꢄꢅꢃꢠ=ꢆꢇꢈꢉꢊꢋꢋꢃꢠ
ꢗꢋꢤꢥꢁꢜꢄꢋꢉ
%
%
%
%
%
%
%
%
%
%
%
%
%
%
ꢓ
ꢑ
Z
ꢒ
X
ꢔ
ꢕ
%&
%%
%Y
%ꢓ
%ꢑ
%Z
`ꢊꢠꢠꢦꢞꢇꢥꢁ`ꢊꢈꢃꢁꢖꢚꢄꢉꢁꢝꢢꢄꢡꢇ'
NOTE: Some parts are listed and shown for illustration purposes only, and are not
available individually as replacement parts.
SKU 46389
PAGE 10
|