Harman Kardon Home Theater System CP 35 User Manual

CP35 QUICK-START GUIDE  
Thank you for purchasing a Harman Kardon CP 35 Home Theater System. This  
Quick-Start Guide will help you with a basic system installation. For detailed  
information on any step in this Guide, please refer to the pages referenced in  
the Owner’s Manual for the AVR 335, which is part of this system. We strongly  
recommend that you read all four Owner’s Manuals for complete details on  
how to install, configure and operate the AVR 335, DVD 31, HKTS 14 and  
HKS 4, as well as for the important safety information they contain. You should  
also read the Owner’s Manual for the included RCP 2 system remote.  
FRONT  
RIGHT  
SPEAKER  
CENTER  
SPEAKER  
(Green)  
FRONT  
LEFT  
SPEAKER  
(Red)  
(White)  
SURROUND  
RIGHT  
SPEAKER  
Figure 1 – Speaker Placement  
The colors shown for each speaker correspond to  
the matching output terminal connection on the back  
of the AVR 335 (see page 7).  
(Gray)  
SUBWOOFER  
(Purple)  
SURROUND  
LEFT  
SPEAKER  
Connections Color Guide  
Audio Connections  
Front  
Left  
Right  
SURROUND  
BACK  
RIGHT  
SPEAKER  
(Tan)  
(Blue)  
Center  
SURROUND  
BACK  
Surround  
LEFT  
SPEAKER  
(Brown)  
Subwoofer  
Surround Back  
Digital Audio Connections  
Coax  
Step 1. Place your speakers in the listening room  
(see page 16).  
Optical  
Video Connections  
Composite  
S-Video  
Match the colored jacks on the AVR 335 to the appropriate  
jacks on your source equipment or speakers. The colors are  
standardized, but not all equipment or connectors use them.  
SPEAKER PLACEMENT  
 
FM Antenna  
AM Antenna  
91329  
240  
Figure 4 – DVD Connections  
Dashed lines (– – – –) indicate coax  
and optical digital audio connections.  
Choose either type (but not both) for  
each digital audio source.  
Figure 5 – Connecting EzSet+  
Microphone  
Step 4. Connect AM and FM antennas, as shown above (see page 14).  
Step 5. Connect the DVD 31 to the AVR 335 as shown above:  
AUDIO connections: Connect the L/R Audio Out jacks on the DVD  
to the L/R DVD Audio in jacks on the AVR.  
back of this Guide. Plug all sources into an AC power outlet.  
at your normal listening position. If desired, the mike may be  
attached to a standard camera tripod using the threads on the  
bottom of the mike. Follow the instructions on pages 20–21 of  
the Owner’s Manual, which contains the steps needed to activate  
the system. As EzSet+ senses the output of each speaker, you will  
hear loud test signals. This is a normal part of the EzSet+ process.  
When the on-screen menu indicates that setup is complete, your  
system is adjusted for output levels, delay times and speaker set-  
tings. Unplug the microphone and store it for future use.  
Step 10. If you are using a component video connection to a digital television,  
set the DVD 31’s output to Progressive Scan, as shown on page 17  
of the DVD 31 manual.  
Step 7. Connect the AVR to your TV or video display. You must make a  
composite, “S” or component video connection corresponding  
corresponding to each video source device used in your system.  
Remember to switch the TV to the correct input for each source.  
NOTE: The AVR’s on-screen menus are not available when viewing  
a component video connection. For that reason, a composite or  
S-video connection is recommended, though not required, when  
component video is used.  
DIGITAL AUDIO connections: Use the enclosed coaxial interconnect  
(orange connectors) to connect the Coaxial Digital Output on the  
DVD to the Coaxial Digital 1 Input on the AVR.  
VIDEO connections: Depending on the input available on your TV,  
use either composite video (dotted yellow), S-video (dotted black)  
or component video (dotted red/blue/green) connections. Only one  
connection type is needed.  
POWER: Plug the DVD’s AC power cord into the SWITCHED output  
on the back of the AVR. Press the Main Power Switch on the DVD so  
that it is ON (see page 17).  
Basic Configuration  
Step 8. Select digital inputs: Use the On-Screen Input Setup menu or the  
front-panel Digital Select button and the arrow buttons to select an  
optical or coaxial digital input, for any digital source of the DVD  
(see page 18).  
Step 11. Your system is configured – sit back and enjoy!  
Step 6. Connect other source devices such as a VCR, Cable or Satellite set-  
top box, HDTV receiver or audio recorder using the connections  
shown in the Device Connection Options chart and Figure 6 on the  
+
Step 9. Use  
to configure and optimize your system.  
Plug the EzSet+ microphone into the front-panel Headphones  
Jack (Fig. 5). Place the microphone at the center of the room, or  
SPEAKER AND DVD CONNECTIONS  
 
VCR (Video 1)  
R
TV or Video Monitor  
S-Video  
Cable or Sat or HDTV Set-Top Box (Video 2)  
OUT  
L
VIDEO  
Video  
Component Video  
Component Video  
L
R
Video  
S-Video  
Y
Pb  
Pr  
Y
Pb  
Pr  
IN  
In/Rec  
Out/Play  
Optical  
Coax  
AUDIO RECORDER  
Figure 6 – Source Component Connections  
Dashed lines (– – – –) indicate coax and optical digital audio connections. Choose either type (but not both) for each  
digital audio source.  
REC/IN  
PLAY/OUT  
Dotted lines (••••) indicate component, composite or S-vdeo connections. Component video is the preferred connection  
when available, but you may use any of the three types (but not more than one). When component, composite and  
S-video sources are connected to the AVR, you must also connect all outputs from the AVR to your TV.  
Device Connection Options: Recommended connections are shown in red, but connections may be made to best fit your system requirements. The Video 4, Coax 3 and Optical 3 inputs are on the front panel of the receiver.  
Device  
CD Player  
DVD Player  
VCR  
Input Name  
CD  
Audio Input Connections  
Audio Output Connections  
Not required  
Video Connections  
Not required  
CD L/R Inputs, Optical Digital 1, 2 or 3, or Coaxial Digital 1, 2 or 3  
Coaxial Digital 1, 2 or 3, Optical Digital 1, 2 or 3, or DVD L/R Inputs  
Video 1 L/R Inputs  
DVD  
Not required  
DVD Component, Composite or S-Video  
Video 1 Composite or S-Video Input and Output  
Video 3 Composite or S-Video Input  
Video 1  
Video 1 L/R Outputs  
Not required  
Cable Box or Satellite Receiver Video 3  
Video 3 L/R Inputs, Optical Digital 1/2/3*, or Coaxial Digital 1/2/3* Inputs  
Audio Recorder  
TV or Projector  
Tape  
Tape L/R Inputs, Optical Digital 1/2/3** or Coaxial Digital 1/2/3** Inputs  
Not required  
Tape L/R Outputs, Digital Optical** or Coaxial Outputs** Not required  
Not required Monitor-Out Component, Composite and/or S-Video  
Not applicable  
Check with your cable company to determine whether digital audio is available for all channels. It may be necessary to make BOTH analog and digital connections if it is not.  
Digital audio recorders only.  
*
**  
®
SOURCE COMPONENT CONNECTIONS  
 

Grizzly Planer G0550 G0551 User Manual
Grizzly Planer G1017 User Manual
HANNspree Flat Panel Television DT12 10H1 User Manual
HANNspree Flat Panel Television F651 12A1 User Manual
Harbor Freight Tools Vacuum Cleaner 3394 User Manual
Health O Meter Scale HDL155 01 User Manual
Hearth and Home Technologies Indoor Fireplace SMARTBATT HNG User Manual
Honeywell Automobile Parts ML6131 User Manual
Honeywell Door 5828 User Manual
Icom Stereo Amplifier IC 7700 User Manual