Honeywell Smoke Alarm ANN RLY User Manual

Mounting in FACP Main Board Chassis  
ANN-RLY Relay Module  
Installation Instructions  
ANN-RLY module standoffs  
The ANN-RLY relay module provides 10 program-  
mable Form-C relays when used with a compatible  
FACP (Fire Alarm Control Panel). This document  
is provided as a quick reference. For more detailed  
information, refer to the appropriate FACP installa-  
tion manual.  
R1 R3 R5 (top)  
R1 R3 R5  
R7 R9  
R7 R9  
ground  
wire  
R2 R4 R6 (bottom) R8 R10  
Note: Installation and wiring of this device must be  
done in accordance with NFPA 72 and local  
ordinances.  
ANN-RLY module mounting hooks  
1. Install the two supplied snap-in standoffs into the  
backside of theANN-RLY circuit board in  
locations indicated in illustration above.  
Specifications  
2. Using supplied hardware, attach the ground wire  
using a screw and nut to location indicated in  
illustration above. Be sure to position the ground  
wire as shown to facilitateANN-RLYinstallation.  
3. Position theANN-RLY module in the chassis so  
that the two standoffs in the module are posi-  
tioned over the wider portion of the mounting  
holes in the chassis and the mounting hooks on  
the module are sticking through the module  
mounting slots in the bottom of the chassis.  
4. Slide theANN-RLY module to the right to lock  
the module into place.  
Table 1: ANN-RLY Module Specifications  
Operating Voltage  
24 VDC  
75 mA  
15 mA  
Max. Current @ Alarm  
24 VDC  
Standby  
0o to 49o C  
(32o to 120o F)  
Operating Temperature  
Max. Wiring Distance from  
FACP (with 12 AWG wire)  
1,250 ft.  
(380 m)  
Relay Contact Ratings  
2 amps @ 30 VDC  
(resistive)  
5. Attach the ground wire installed in step 2 to the  
chassis in the location indicated below.  
0.5 amps @ 30 VAC  
(resistive)  
chassis  
Indoor Use in Dry Location Only  
Mounting  
TheANN-RLY module may be mounted inside the  
FACP main circuit board chassis or in the battery  
area of the enclosure using mounting bracket P/N:  
ANN-MBRLY. Refer to the following illustrations  
for installation information.  
ANN-RLY module  
mounting holes  
ANN-RLY module  
ground  
wire  
mounting slots  
Note:  
1. ANN-RLY module can be installed without  
removing the main circuit board or chassis.  
2. ANN-MBRLY mounting bracket must be used  
for the MS-9200UDLS.  
1
ANN-RLY Module  
Document # 53033 Rev. B 10/10/07  
ECN 07-744  
 
Wiring ANN-RLY Module to FACP Setting DIP Switches  
Refer to Table 2 and Figure 3 for wiring  
connections.  
Each ANN-BUS device requires a unique address.  
ANN-RLY relay module DIP switch SW1 is used  
to set the address for the annunciator.  
ANN-RLY Terminals (TB1) FACP ANN-BUS Terminals  
A maximum of 8 devices can be connected to the  
FACPANN-BUS communication circuit. ANN-  
BUS device addresses do not need to be sequential  
and can be set to any number between 01 and 08.  
Note that 00 is not a valid address. The following  
illustrates the DIP switch settings for each address  
(ID Number):  
Terminal 4 (-)  
Terminal 3 (+)  
Terminal 2 (A)  
Terminal 1 (B)  
(-)  
(+)  
A (ANN-BUS)  
B (ANN-BUS)  
Table 2: Wiring ANN-RLY Module to FACP  
ID Number  
(Address)  
DIP Switch SW1  
C
NC  
NO  
(not valid) 00  
C
NC  
NO  
01  
02  
03  
04  
05  
06  
07  
08  
ANN-RLY Relay Module  
Figure 3: Wiring ANN-RLY Module to an FACP  
Notes:  
1. All connections/sources are to be power-limited  
and supervised.  
2. 12 - 18 AWG (0.75 - 3.25 mm2) wire for 24  
VDC circuit is acceptable. Refer to the  
appropriate FACP manual.  
3. Power wire distance limitation is set by 1.2 volt  
maximum line drop from source to end of  
circuit.  
4. Maximum distance from FACP to last ANN-  
BUS device must not exceed 1,250 feet  
(380 m). Refer to Wiring Distance Table in  
appropriate FACP manual for wire gauge and  
distance limitations.  
5. Common, Normally Closed and Normally Open  
terminals for each relay follow the same  
pattern as illustrated above.  
One Fire-Lite Place  
Northford, CT 06472  
USA TEL: (203) 484-7161  
© 2006 Fire-Lite Alarms P/N: 53033  
3
ANN-RLY Module  
Document # 53033 Rev. B 10/10/07  
ECN 07-744  
 

Graco Baby Swing PD162294B User Manual
Graco Humidifier ti25442a User Manual
Graco Oven 309572ZAG User Manual
Gravely Lawn Mower 988100 User Manual
Grundig CRT Television GUVCD2800 User Manual
Harbor Freight Tools Water Pump 68328 User Manual
Hasbro Motorized Toy Car 83453 ASST User Manual
Honeywell Home Security System 408 User Manual
Hoshizaki Ice Maker KM 250BAF User Manual
IDEAL INDUSTRIES Boiler C24 User Manual