Hotpoint Oven AHP69PGX User Manual

Operating Instructions

OVEN

Contents

Installation, 2

Positioning

Electrical connection, 3

Data plate

English, 1

Description of the appliance, 4

Overall view

Control panel

Display

Start-up and use, 5

Setting the clock

Setting the timer

Starting the oven

Cooking modes, 6-8

Cooking modes

AHP69PX

Programming cooking

Practical cooking advice

Cooking advice table

AHP69PGX

Precautions and tips, 9

General safety

Disposal

Respecting and conserving the environment

Care and maintenance, 10-11

Switching the appliance off

Cleaning the appliance

Cleaning the oven door

Replacing the light bulb

Automatic cleaning with the AST CLEAN function

After Sales Service, 12

Repair Service and Information Desk

Extended Warranties

Genuine Parts and Accessories

Guarantee, 13

Electrical Connection

Electrical connection

Power cable supply connection to the electrical

mains:

The electrical connection to the mains must be made

on the appliance. The power voltage and frequency

are as indicated on the rating plate.

We recommend you use a power supply cable which

is long enough to allow you to take the oven out of

its recess in the event of maintenance operations

(only use HAR - H 05 - RR quality cables fitted with

a plug conforming to the regulations in force.

The plug must be accessible at all times.

! THIS APPLIANCE MUST BE EARTHED.

Connecting the power supply cable

Unplug the appliance before all operations, even

when replacing the oven lamp.

To open the terminal board:

• Using a screwdriver, press on the tabs situated

on each side of the terminal board cover.

Using the appliance without correct earthing is

highly dangerous.

• Pull open the terminal board cover.

! After connecting the appliance to the flexible

cable, tighten all the screws on the terminal

board.

To connect the power supply cable, proceed as

follows:

• Unscrew the cable clamp screw and the contact

screws L-N-6.

• asten the wires beneath the screwheads using

the following colour scheme: Blue (N) Brown (L)

Yellow-Green 6

TABLE O CHARACTERISTICS

width 43.5 cm

height 32 cm

depth 40 cm

• asten the power supply cable in the

corresponding cable clamp and close the cover.

Dimensions

Volume

56 l

Electrical Connection:

voltage: 220-240 V~ 50/60Hz

maximum power absorbed 2800W

(see data plate)

Electrical

connections

Voltage requency: 230

V-1+N 50Hz

use Section: 16A

Directive 2002/40/EC on the label of

electric ovens. Standard EN 50304

Supply cable:

3x1.5mm²

Energy consumption for Natural

convection – heating mode:

Traditional mode

ENERGY

LABEL

Declared energy consumption for

Forced convection Class – heating

mode:

Baking

You can connect your oven to the system means of

a terminal board. Refer to above information for the

minimal cable sections and the calibration of the

protective elements according to the connection.

If the appliance is installed with a junction box, an

omnipolar circuit breaker - with a minimum contact

opening of 3mm - should be installed between the

appliance and the mains.

This appliance conforms to the

following European Economic

Community directives: 2006/95/EEC

dated 12/12/06 (Low Voltage) and

subsequent amendments -

89/336/EEC dated 03/05/89

(Electromagnetic Compatibility) and

subsequent amendments -

93/68/EEC dated 22/07/93 and

subsequent amendments.

2002/96/EC

Description

of the appliance

Overall view

GUIDES for the

sliding racks

Control panel

position 5

position 4

position 3

position 2

position 1

GRILL

DRIPPING PAN

Control panel

SELECTOR

Knob

DISPLAY

THERMOSTAT

knob

FAST CLEAN

button

TIME SETTING

button

TIMER

knob

Display

TEMPERATURE

Preheating

and TIME digits

indicator

CLOCK

icon

STOP

icon

END OF COOKING

DOOR LOCK

icon

indicator

DURATION

TIMER

icon

Start-up and use

! The first time you use your appliance, heat the

empty oven with its door closed at its maximum

temperature for at least half an hour. Ensure that the

room is well ventilated before switching the oven off

and opening the oven door. The appliance may emit

a slightly unpleasant odour caused by protective

substances used during the manufacturing process

burning away.

complete: you may now place the food in the oven.

4. During cooking it is always possible to:

- change the cooking mode by turning the

SELECTOR knob

- change the temperature by turning the

THERMOSTAT knob

- set the cooking duration in addition to the cooking

end time

(see Cooking modes)

- stop cooking by turning the SELECTOR knob to the

“0” position.

Setting the clock

5. The oven switches off automatically after two

hours: this default period of time is set for all

cooking modes for safety reasons.

The cooking duration may be changed

(see Cooking modes).

! The clock may be set when the oven is switched

off or when it is switched on, provided that a the end

time of a cooking cycle has not been programmed

previously.

6. If a blackout occurs while the oven is already in

operation, an automatic system within the appliance

will reactivate the cooking mode from where it was

interrupted as long as the temperature has not

dropped below a certain level. Programmed cooking

modes which have not started will not be restored

and must be reprogrammed.

1. Press the

button several times until the

icon and the first two digits on the display start to flash.

2. Turn the TIMER KNOB towards “+” and “-” to

adjust the hour value.

3. Press the

button again until the other two

digits on the DISPLAY begin to flash.

4. Turn the TIMER KNOB towards “+” and “-” to

adjust the minute value.

! There is no preheating stage for the BARBECUE

modes.

5. Press the

button again to confirm.

! Never put objects directly on the bottom of the

oven; this will avoid the enamel coating being

damaged.

Setting the timer

! This function does not interrupt cooking and does

not affect the oven; it is simply used to activate the

buzzer when the set amount of time has elapsed.

! Always place cookware on the rack(s) provided.

Cooling ventilation

1. Press the

button several times until the

icon and the three digits on the display begin to

flash.

In order to cool down the external temperature of the

oven, a cooling fan blows a stream of air between

the control panel and the oven door. In the BAKING

mode, the cooling fan is only activated when the

oven is hot. At the beginning of the AST CLEAN

mode, the cooling fan operates at low speed.

2. Turn the TIMER KNOB towards “+” and “-” to

adjust the minute value.

3. Press the

button again to confirm.

The display will then show the time as it counts

down. When this period of time has elapsed the

buzzer will be activated.

! Once cooking has been completed, the cooling fan

continues to operate until the oven has cooled down

sufficiently.

Starting the oven

1. Select the desired cooking mode by turning the

SELECTOR knob.

Oven light

2. The oven begins its preheating stage and the

preheating indicator lights up.

When the oven is off, the lamp can be turned on at

any time by opening the oven door.

The temperature may be changed by turning the

THERMOSTAT knob

3. When the preheating indicator

switches off

and a buzzer sounds the preheating process is

Cooking modes

BAKING mode

! All cooking modes have a default cooking

temperature which may be adjusted manually

between 40°C and 250°C as desired.

This mode is ideal for baking temperature sensitive

foods (such as cakes, which need to rise) and for

the preparation of “bitesize pastries” on 3 shelves

simultaneously.

In the BARBECUE mode, the default power level

value is indicated as a percentage (%) and may also

be adjusted manually.

PIZZA OVEN mode

TRADITIONAL OVEN mode

This combination heats the oven rapidly by producing

a considerable amount of heat, particularly from the

element at the bottom. If you use more than one rack

at a time, switch the position of the dishes halfway

through the cooking process.

When using this traditional cooking mode, it is best

to use one cooking rack only. if more than one rack

is used, the heat will be distributed unevenly.

MULTI-COOKING mode

ROTISSERIE mode

Since the heat remains constant throughout the

oven, the air cooks and browns food in a uniform

manner. A maximum of two racks may be used at

the same time.

The top and circular heating elements switch on and

the fan begins to operate. This combination of

features increases the effectiveness of the

unidirectional thermal radiation of the heating

elements through forced circulation of the air

throughout the oven.

GRILL mode

This helps prevent food from burning on the surface,

allowing the heat to penetrate right into the food.

Always cook in this mode with the oven door closed.

By turning the THERMOSTAT knob, the different

power levels which may be set will appear on the

display; these range between 50% and 100%. The

high and direct temperature of the grill is

recommended for food which requires a high surface

temperature. Always cook in this mode with the oven

door closed.

LOW TEMPERATURE mode

This type of cooking can be used for warming

dishes or already cooked meals. The temperature is

65°C.

=AN GRILLING mode

This combination of features increases the

effectiveness of the unidirectional thermal radiation

provided by the heating elements through forced

circulation of the air throughout the oven.

This helps prevent food from burning on the surface

and allows the heat to penetrate right into the food.

Always cook in this mode with the oven door closed.

Programming cooking

Practical cooking advice

! A cooking mode must be selected before

programming can take place.

! Do not place racks in position 1 and 5 during fan-

assisted cooking. This is because excessive direct

heat can burn temperature sensitive foods.

Programming the cooking duration

! In the GRILL and AN GRILLING cooking modes,

particularly when using the rotisserie spit, place the

dripping pan in position 1 to collect cooking

residues (fat and/or grease).

1. Press the

button several times until the

icon and the three digits on the DISPLAY begin to

flash.

2. Turn the TIMER KNOB towards “+” and “-” to

adjust the duration.

MULTI-COOKING

3. Press the

button again to confirm.

4. When the set time has elapsed, the text END

appears on the DISPLAY, the oven will stop cooking

and a buzzer sounds.

• Use positions 2 and 4, placing the food which

requires more heat on 2.

• or example: it is 9:00 a.m. and a time of 1 hour

and 15 minutes is programmed. The programme

will stop automatically at 10:15 a.m.

• Place the dripping pan on the bottom and the rack

on top.

GRILL

Setting the end time for a cooking mode

! A cooking duration must be set before the end

cooking time can be scheduled.

• Place the rack in position 3 or 4. Position the food

in the centre of the rack.

1. ollow steps 1 to 3 to set the duration as detailed

above.

• We recommend that the power level is set to

maximum. The top heating element is regulated

by a thermostat and may not always operate

constantly.

2. Next, press the

button until the

icon and

the two digits on the DISPLAY begin to flash.

3. Turn the TIMER KNOB towards “+” and “-” to

adjust the hour value.

PIZZA OVEN

4. Press the

button again until the other two

• Use a light aluminium pizza pan. Place it on the

rack provided.

digits on the DISPLAY begin to flash.

5. Turn the TIMER KNOB towards “+” and “-” to

adjust the minute value.

or a crispy crust, do not use the dripping pan as

it prevents the crust from forming by extending

the total cooking time.

6. Press the

button again to confirm.

7. When the set time has elapsed, the text END

appears on the DISPLAY, the oven will stop cooking

and a buzzer sounds.

• If the pizza has a lot of toppings, we recommend

adding the mozzarella cheese on top of the pizza

halfway through the cooking process.

Programming has been set when the

and

buttons are illuminated. The DISPLAY shows the

cooking end time and the cooking duration

alternately.

To cancel programming, turn the SELECTOR knob to

the “0” position.

Cooking advice table

Cooking modes

ꢀoods

Weight(in

kg)

Rack

position

Preheating

Recommended

Temperature

(°C)

Cooking

duration

(minutes)

Duck

Chicken

Roast veal or beef

Roast pork

Biscuits (shortcrust pastry)

Pies / Tarts

1.5

Yes

200-210

200

200-210

180

70-80

60-70

70-75

70-80

15-20

30-35

Traditional Oven

Multi-cooking

180

Pizza on 2 racks

2 and 4

1 and 2/3

1 or 2

2 and 4

1 and 3

Yes

220-230

180

170

200-210

190-200

180

190-200

190

20-25

30-35

20-25

65-75

45-50

30-35

35-40

20-25

10-20

20-25

20-30

Pies on two racks/cakes on 2 racks

Sponge cake on 2 racks (on the dripping pan)

Roast chicken + potatoes

Lamb

Mackerel

Lasagne

Cream puffs on 2 racks

Biscuits on 2 racks

Cheese puffs on 2 racks

Savoury pies

1+1

190

210

200

Grill

Mackerel

Sole and cuttlefish

Squid and prawn kebabs

Cod fillet

Grilled vegetables

Veal steak

Sausages

Hamburgers

0.7

0.5

0.8

0.7

4 or 5

4 or 6

100%

15-20

10-15

8-10

10-15

15-20

10-12

3-5

3 or 4

Toasted sandwiches (or toast)

Spit-roast chicken using rotisserie spit (where

present)

70-80

Spit-roast lamb using rotisserie spit (where present)

100%

70-80

Grilled chicken

Cuttlefish

Spit-roast chicken using rotisserie spit (where

1,5

210

200

210

55-60

30-35

70-80

ꢀan grilling

present)

Spit-roast duck using rotisserie spit (where present)

1,5

210

60-70

60-75

70-80

40-45

Roast veal or beef

Roast pork

Lamb

Pies / Tarts

Fruit cakes

0.5

2 or 3

2 and 4

2 or 3

1, 3 and 5

Yes

180

170-180

180-190

160-170

180-190

180

200

210

25-35

40-50

45-55

20-25

30-40

20-25

30-35

180

Baking mode

Sponge cake made with yoghurt

Small cakes on 2 racks

Sponge cake

Cream puffs on 3 racks

Biscuits on 3 racks

Filled pancakes

0.7

0.6

0.7

0.8

0.5

Meringues on 3 racks

Cheese puffs

1, 3 and 5

20-25

Pizza

Focaccia bread

0.5

Yes

220

200

15-20

20-25

PizzaOven

Rotisserie

Grilled chicken

Duck

Roast veal or beef

Roast pork

Lamb

1.5

210

180

60-70

50-60

60-75

60-70

40-45

Lasagne

Defrosting

Dish heating

Pasteurisation

2 or 3

Low

temperature

! The cooking times listed above are intended as guidelines only and may be modified according to personal tastes. Oven preheating times are set as standard

and may not be modified manually.

Precautions and tips

! This appliance has been designed and

• Do not rest heavy objects on the open oven door.

manufactured in compliance with international safety

standards. The following warnings are provided for

safety reasons and must be read carefully.

• The appliance should not be operated by people

(including children) with reduced physical,

sensory or mental capacities, by inexperienced

individuals or by anyone who is not familiar with

the product. These individuals should, at the very

least, be supervised by someone who assumes

responsibility for their safety or receive

General safety

• The appliance was designed for domestic use

inside the home and is not intended for

commercial or industrial use.

preliminary instructions relating to the operation of

the appliance.

• Do not let children play with the appliance.

• The appliance must not be installed outdoors, even

in covered areas. It is extremely dangerous to

leave the appliance exposed to rain and storms.

• When moving or positioning the appliance, always

use the handles provided on the sides of the oven.

• Do not touch the appliance with bare feet or with

wet or damp hands and feet.

Disposal

• When disposing of packaging material: observe local

legislation so that the packaging may be reused.

• The European Directive 2002/96/EC relating to

Waste Electrical and Electronic Equipment (WEEE)

states that household appliances should not be

disposed of using the normal solid urban waste

cycle. Exhausted appliances should be collected

separately in order to optimise the cost of re-using

and recycling the materials inside the machine,

while preventing potential damage to the

• The appliance must be used by adults only for the

preparation of food, in accordance with the

instructions provided in this booklet.

• Do not touch the heating elements or certain

parts of the oven door when the appliance is in

use; these parts become extremely hot. Keep

children well away from the appliance.

• Ensure that the power supply cables of other

electrical appliances do not come into contact

with the hot parts of the oven.

atmosphere and to public health. The crossed-out

dustbin is marked on all products to remind the

owner of their obligations regarding separated waste

collection. or further information relating to the

correct disposal of exhausted household

• The openings used for the ventilation and

dispersion of heat must never be covered.

• Always grip the oven door handle in the centre:

the ends may be hot.

appliances, owners may contact the public service

provided or their local dealer.

• Always use oven gloves when placing cookware

in the oven or when removing it.

Respecting and conserving the

environment

• Do not use aluminium foil to line the bottom of the oven.

• Do not place flammable materials in the oven: If

the appliance is switched on accidentally, the

materials could catch fire.

• You can help to reduce the peak load of the

electricity supply network companies by using the

oven in the hours between late afternoon and the

early hours of the morning. The cooking mode

programming options, the “delayed cooking”

mode (see Cooking modes) and “delayed

automatic cleaning” mode (see Care and

Maintenance) in particular, enable the user to

organise their time efficiently.

• Always make sure the knobs are in the “l”/“¡”

position when the appliance is not in use.

• When unplugging the appliance, always pull the

plug from the mains socket; do not pull on the

cable.

• Never perform any cleaning or maintenance work

without having disconnected the appliance from

the electricity mains.

• Always keep the oven door closed when using the

GRILL and AN GRILLING modes: This will

achieve improved results while saving energy

(approximately 10%).

• If the appliance breaks down, under no

circumstances should you attempt to perform the

repairs yourself. Repairs carried out by

inexperienced persons may cause injury or further

malfunctioning of the appliance. Contact a Service

Centre (see Assistance).

• Check the door seals regularly and wipe them clean

to ensure they are free of debris so that they adhere

properly to the door, thus avoiding heat dispersion.

Care and maintenance

Switching the appliance off

3. Grip the door on the two

external sides and close it

approximately half way. Pull

the door towards you, lifting it

out of its slot (see diagram).

Disconnect your appliance from the electricity

supply before carrying out any work on it.

Cleaning the appliance

• The stainless steel or enamel-coated external

To replace the door, reverse this sequence.

Inspecting the seals

parts and the rubber seals may be cleaned using

a sponge that has been soaked in lukewarm water

and neutral soap. Use specialised products for

the removal of stubborn stains. After cleaning,

rinse and dry thoroughly. Do not use abrasive

powders or corrosive substances.

Check the door seals around the oven periodically. If

the seals are damaged, please contact your nearest

After-sales Service Centre (see Assistance). We

recommend that the oven is not used until the seals

have been replaced.

• The inside of the oven should ideally be cleaned

after each use, while it is still lukewarm. Use hot

water and detergent, then rinse well and dry with

a soft cloth. Do not use abrasive products.

• The accessories can be washed like everyday

crockery, and are even dishwasher safe.

! Never use steam cleaners or pressure cleaners on

the appliance.

Replacing the light bulb

To replace the oven light bulb:

Oven

compartment

Cleaning the oven door

Lamp

Clean the glass part of the oven door using a

sponge and a non-abrasive cleaning product, then

dry thoroughly with a soft cloth. Do not use rough

abrasive material or sharp metal scrapers as these

could scratch the surface and cause the glass to

crack. or more thorough cleaning purposes, the

oven door may be removed:

Seal

Glass door

1. Open the oven door fully

(see diagram).

1. Remove the glass cover using a screwdriver.

2. Unscrew the light bulb and replace it with a

similar one: Wattage 15 W, cap E 14.

Replace the glass cover, making sure the seal is

positioned correctly (see diagram).

Warning:

The appliance is fitted with an automatic diagnostic

system which detects any malfunctions.

Malfunctions are displayed by messages of the

following type: ” ” followed by numbers.

Call for technical assistance should a malfunction

occur.

2. Lift up and turn the small

levers located on the two

hinges (see diagram).

! Never use the services of an unauthorised

technician.

Automatic cleaning with the ꢀAST

CLEAN function

Safety devices

• The

icon on the display, when lit, indicates

With the AST CLEAN mode, the internal

temperature of the oven reaches 500°C. The

pyrolytic cycle is activated, burning away food and

grime residues. Dirt is literally incinerated.

Keep children away from the appliance during the

automatic cleaning cycle as surfaces may become

very hot. Particles may ignite inside the oven due to

the combustion process. There is no cause for

concern: this process is both normal and hazard-

free.

that the oven door was automatically locked as soon

as the temperature reached a high value.

• The

icon indicates that the cleaning cycle

may be cancelled at any time by pressing the

button.

• If a malfunction occurs, the heating elements will

be switched off.

• Once the oven door has been locked, you cannot

change the duration and cycle end time settings.

Before initiating the AST CLEAN mode:

• Remove large or coarse food residues from the

inside of the oven using a damp sponge. Do not use

detergents.

Programming the automatic cleaning end time

1. Press the

button until the

icon and the two

• Remove all accessories.

digits on the DISPLAY begin to flash.

2. Turn the TIMER KNOB towards “+” and “-” to

adjust the hour value.

• Do not place tea towels or pot holders over the

oven handle.

3. Press the

button again until the other two

digits on the DISPLAY begin to flash.

4. Turn the TIMER KNOB towards “+” and “-” to

adjust the minute value.

• Turn the SELECTOR knob to the “0” position.

! If the oven is too hot, the pyrolytic cycle may not

start. Wait for the oven to cool down.

5. Press the

button again to confirm.

6. When the set time has elapsed, the text END

appears on the display and a buzzer sounds.

• or example: it is 9:00 a.m. and the Economy

(ECO) AST CLEAN level has been selected, with

the default duration of 1 hour. 12:30 is scheduled as

the end time. The programme will start automatically

at 11:30 a.m.

! The programme may only be started once the oven

door has been closed.

To activate the AST CLEAN cycle press and hold

the

button for approximately 4 seconds. The

TIMER KNOB may be used to select the desired

cleaning level; there are three default time settings

which cannot be modified.

Programming has been set when the and

buttons are illuminated. The display shows the AST

CLEAN end time and duration alternately.

1. Economy (ECO): turn the knob towards “-”.

Duration 1 hour.

Once the automatic cleaning cycle is over

2. Normal (NOR): initial level. Duration 1 hour and 30

minutes.

You will have to wait until the temperature inside the

oven has cooled down sufficiently before you can

open the oven door. You will notice some white dust

deposits on the bottom and the sides of your oven;

remove these deposits with a damp sponge once

the oven has cooled down completely. Alternatively,

you can make use of the already heated oven, in

which case it is not necessary to remove the

deposits, they are completely harmless and will not

affect your food in any way.

3. Intensive (INT): turn the knob towards “+”.

Duration 2 hours.

4. Press the

button to confirm.

An end time for the AST CLEAN cycle (as for a

normal cooking cycle) may be programmed (see

Programming the automatic cleaning end time).

After Sales Service

No one is better placed to care for your Hotpoint appliance during the course of its working life than

us - the manufacturer.

Essential Contact Information

Hotpoint Service

We are the largest service team in Europe offering you access to 400 skilled telephone advisors and

1100 fully qualified engineers on call to ensure you receive fast, reliable, local service.

UK: 08709 066 066

Republic of Ireland: 0818 313 413

www.hotpointservice.co.uk

Please note: Our advisors will require the following information:

Model number:

Serial number:

Parts and Accessories

We supply a full range of genuine replacement parts as well as accessory products that protect and

hygienically clean your appliance to keep it looking good and functioning efficiently throughout its life.

UK: 08709 077 077

Republic of Ireland: 0818 313 413

www.hotpointservice.co.uk

Appliance Registration

We want to give you additional benefits of Hotpoint ownership. To activate your free 5 year parts

guarantee you must register your appliance with us.

UK: 0870 6092094

Republic of Ireland: 01 230 0800

www.hotpointservice.co.uk

Indesit Company UK Ltd. Morley Way, Peterborough, PE2 9JB

Indesit Company Unit 49 Airways Industrial Estate,Dublin 17

Recycling & Disposal Information

As part of Hotpoint's continued commitment to helping the environment, Hotpoint reserves the right to use

quality, recycled components to keep down customer costs and minimise material wastage.

Please dispose of packaging and old appliances carefully. To minimise the risk of injury to children,

remove the door, plug and cut the mains cable off flush with the appliance. Dispose of these parts

separately to ensure that the appliance can no longer be plugged into a mains socket, and the door cannot

be locked shut.

Guarantee

12 Months Parts and Labour Guarantee

Your appliance has the benefit of our manufacturer’s guarantee, which covers the cost of breakdown

repairs for twelve months from the date of purchase.

This gives you the reassurance that if, within that time, your appliance is proven to be defective because

of either workmanship or materials, we will, at our discretion, either repair or replace the appliance at no

cost to you.

This guarantee is subject to the following conditions:

- The appliance has been installed and operated correctly and in accordance with our

operating and maintenance instructions.

The appliance is used only on the electricity or gas supply printed on the rating plate.

The appliance has been used for normal domestic purposes only.

The appliance has not been altered, serviced, maintained, dismantled, or otherwise

interfered with by any person not authorised by us.

Any repair work must be undertaken by us or our appointed agent.

Any parts removed during repair work or any appliance that is replaced become our property.

The appliance is used in the United Kingdom or Republic of Ireland.

The guarantee does not cover:

Damage resulting from transportation, improper use, neglect or interference or as a result

of improper installation.

Replacement of any consumable item or accessory . These include but are not limited to: plugs,

cables, batteries, light bulbs, fluorescent tubes and starters, covers and filters.

Replacement of any removable parts made of glass or plastic.

THIS GUARANTEE WILL NOT APPLY Iꢀ THE APPLIANCE HAS BEEN USED IN COMMERCIAL

OR NON-DOMESTIC PREMISES.

5 Year Parts Guarantee

Hotpoint also offers you a free 5 year parts guarantee. This additional guarantee is conditional on you

registering your appliance with us and the parts being fitted by one of our authorised engineers. There

will be a charge for our engineer's time. To activate the extra parts warranty on your appliance, simply

call our registration line on 0870 6092094 (ROI 01 230 0800).

Extended Guarantees

We offer a selection of repair protection plans that enable you to fully cover yourself against the expense

of repair bills for the life of your policy. To find the ideal plan for you please call our advice line on 08709

088 088 (ROI 01 230 0233).

ꢀree Helpdesk Service

We have a dedicated team who can provide free advice and assistance with your appliance if you

experience any technical difficulties within the first 90 days of ownership. Simply call our Hotpoint

Service Hotline on 08709 066 066 (ROI 0818 313 413) for telephone assistance, or, where necessary, to

arrange for an engineer to call. If we cannot resolve the technical problem we will replace your machine

or, if you prefer, give you your money back.

Notes

02/2008 - 195058925.01

XEROX BUSINESS SERVICES

Graco Bouncy Seat PD162824A User Manual
Hamilton Beach Blender 840065601 User Manual
Hamilton Beach Blender HBB908 User Manual
Harbor Freight Tools Cordless Sander 38160 User Manual
Harbor Freight Tools Water Pump 3878 User Manual
Heatiator Gas Heater CL36D User Manual
Hotpoint Convection Oven C120E User Manual
Hustler Turf Lawn Mower 114675_0311 C 1 User Manual
IKEA TV Video Accessories AA 204866 4 User Manual
Image Home Gym IMTL139050 User Manual