Instructions for Installation and Use
BS41X
Note: Timer must be set to ‘Time of Day’ and ‘Manual’
before the oven can be used.
Note: Ensure that the oven is securely fixed to the
cabinet before use.
To the Installer
Before installation fill in the product details on the back cover of
this booklet. The information can be found on the rating plate.
To the User
You must read the instructions prior to installing and using the
appliance and then retain them for future reference.
INTRODUCTION
Your new cooker is guaranteed* and will give lasting service. This guarantee
is only applicable if the appliance has been installed in accordance with the
installation instructions detailed in this booklet.
To help make best use of your cooking equipment,
please read this booklet carefully.
The cooker is designed specifically for domestic use and responsibility will not
be accepted for use in any other installation.
Note: When the cooker is first used, an odour may be emitted - this will cease
after a short period of use
To help remove the 'new' smell, heat up the empty oven(s) to maximum for a
minimum of two to three hours keeping the oven doors closed. Ensure that the
room is well ventilated (e.g. open a window or use an extractor fan) and that
persons who may be sensitive to the odour avoid any fumes. It is suggested that
any pets be removed from the room until the smell has ceased.
This odour is due to any temporary finish on oven linings and elements and also
any moisture absorbed by the insulation.
* The guarantee is subject to the provisions that the appliance:
(a) Has been used solely in accordance with the Users Instruction Book.
(b) Has been properly connected to a suitable supply voltage as stated on
the rating plate attached to this equipment.
(c) Has not been subjected to misuse or accident or been modified or
repaired by any person other than the authorised employee or agent.
(d) Has been correctly installed.
This appliance conforms to the following EEC Directives:
Low Voltage Equipment
73/23/EEC
93/68/EEC
Electromagnetic Compatibility
89/336/EEC
92/31/EEC93/68/EEC
3
FOR YOUR SAFETY
When used properly, your appliance is completely safe but as with any
electrical product there are certain precautions that must be observed.
PLEASE READ THE PRECAUTIONS BELOW BEFORE USING YOUR
APPLIANCE.
ALWAYS
Always make sure you remove all packaging and literature from inside the
oven/grill compartment before switching on for the first time.
Always make sure you understand the controls prior to using the appliance.
Always keep children away from the appliance when in use as the surfaces
will get extremely hot during and after cooking.
Always make sure all controls are turned off when you have finished cooking
and when not in use.
Always stand back when opening an oven door to allow any build up of
steam or heat to disperse.
Always use dry, good quality oven gloves when removing items from the
oven/grill.
G
G
G
G
G
G
Always take care to avoid heat/steam burns when operating the controls.
Always turn off the electricity supply at the wall switch before cleaning and
allow the appliance to cool.
Always make sure the shelves are in the correct position before switching on
the oven.
G
G
G
Always keep the oven/grill door closed when the appliance is not in use.
Always keep the appliance clean as a build up of grease or fat from cooking
can cause a fire.
Always follow the basic principles of food handling and hygiene to prevent
the possibility of bacterial growth.
G
G
G
Always keep ventilation slots clear of obstructions.
Always refer servicing to a qualified appliance service engineer.
Always during use the oven becomes hot. Care should be taken to avoid
touching heating elements inside the oven.
G
G
G
SAFETY ADVICE
IN THE EVENT OF A CHIP PAN OR ANY OTHER PAN FIRE:
1. TURN OFF THE COOKER APPLIANCE AT THE WALL SWITCH.
2. COVER THE PAN WITH A FIRE BLANKET OR DAMP CLOTH, this will
smother the flames and extinguish the fire.
3. LEAVE THE PAN TO COOL FOR AT LEAST 60 MINUTES BEFORE
MOVING IT. Injuries are often caused by picking up a hot pan and rushing
outside with it.
NEVER USE A FIRE EXTINGUISHER TO PUT OUT A PAN FIRE as the
force of the extinguisher is likely to tip the pan over. Never use water to
extinguish oil or fat fires.
4
FOR YOUR SAFETY
NEVER
Never leave children unsupervised where a cooking appliance is installed as
G
all cooking surfaces will be hot during and after use.
Never allow anyone to sit or stand on any part of the appliance.
Never store items above the appliance that children may attempt to reach.
Never remove the oven shelves whilst the oven is hot.
Never heat up unopened food containers as pressure can build up causing
the container to burst.
G
G
G
G
Never store chemicals, food stuffs or pressurised containers in or on the
appliance, or in cabinets immediately above or next to the appliance.
Never operate the grill with the door closed as this may cause the appliance
to overheat.
G
G
Never use the appliance as a room heater.
Never use the grill to warm plates.
Never dry any items on the oven doors.
Never install the appliance next to curtains or other soft furnishings.
Never allow children to play with the oven controls.
G
G
G
G
G
DISPOSAL OF YOUR PRODUCT
To minimise the risk of injury to children please dispose of your product carefully and
safely. Remove all doors and lids (where fitted). Remove the mains cable (where fitted)
by cutting off flush with the appliance and always ensure that no plug is left in a condition
where it could be connected to the electricity supply.
To help the environment, Local Authority instructions should be followed for the disposal
of your product.
5
KNOW YOUR OVEN
24 Hour Digital
Electronic Clock
and Oven Timer
Oven Control
and Selector
Grill Control
❍ ❍
Grill Element
Oven Light
Stayclean Liners
Meat/Grill pan
2 Oven Shelves
Oven Fan
Door Switch
Rating plate
Inner Door Glass
6
CONTROL PANEL
B
❍ ❍
A
❍❍❍❍❍❍
CONTROL MARKINGS
Control
Description
Function
Fan Oven
Knob
Oven & Grill Selector
A
Turning control (A) clockwise allows use of fan oven.When
cooking turn to the required setting. The oven temperature
scale is in degrees centigrade.
Oven & Grill Selector
& Grill Control
1 = Low
Half Grill
A & B
Turn control (A) clockwise until the half grill symbol is
indicated. Turn control (B) in either direction to the required
grill setting.
6 = High
Full Grill
A & B
Oven & Grill Selector
& Grill Control
1 = Low
Turn control (A) clockwise until the full grill symbol is
indicated. Turn control (B) in either direction to the required
grill setting.
6 = High
Note: Resistance will be felt when turning from fan oven operation to full grill / half grill positions
Cooling Fan
A gentle flow of air will be blown below the control panel when the oven
or grill is switched on. In some instances this will continue after switch-
ing the oven / grill off. This is not unusual. This helps to keep the control
panel and knobs cool.
Oven Interior The oven light is switched on automatically when the fan oven control
Lights (A) is operated..
Slow Cooking The oven has a “Slow Cook Setting” this can be used for slow cooking,
keeping food warm and / or warming plates for a short period. Turn oven
control (A) to 900C
Note: It is advisable to check that all oven controls have been switched off after
you have finished using the appliance.
7
OVEN TIMER OPERATION
Note: Timer must be set to ‘Time of Day’ and ‘Manual’ before the oven
can be used.
AUTOMATIC COOKING
The Oven can be controlled by the Automatic Timer.
HINTS ON AUTOMATIC COOKING
1. Select foods which will require the same cooking time and temperature.
2. To ensure food does not cool down and require reheating, set the end time so
the food is ready when you require it.
3. Always ensure that meat and poultry is defrosted before placing in the oven.
4. Whenever possible, take food out of the refrigerator and keep it as cool as
possible.
5. If cooking food that requires frying before placing in the oven for automatic
cooking, keep the delay time to a minimum.
6. Never place hot or warm food in the oven for delay start cooking as it could
cause the oven to be warm and produce harmful bacteria in the food.
7. We advise that dishes containing left-over cooked poultry or meat, e.g.
Shepherd's Pie, should not be cooked automatically if there is to be a delay
period.
8. Ensure that delay start times are kept to a minimum to prevent bacterial
growth in food.
9. Wine or beer may ferment and cream may curdle during the delay period so
it is best to add these ingredients just before serving.
10. Foods which discolour should be protected by coating in fat or tossing in
water to which lemon juice has been added, prior to placing food in the oven.
11. Dishes containing liquid should not be filled too full to prevent boiling over.
12. Food should be well sealed (but not airtight) in a container to prevent the loss
of liquid during cooking. Aluminium foil gives a good seal.
13. Always ensure that food is piping hot and cooked thoroughly before serving.
14. Only reheat food once.
8
KNOW YOUR TIMER
CLOCKFACE
The timer incorporates a 24 hour clock.
Ensure correct time of day is always set, before using your cooker.
PLEASE NOTE THAT THE DISPLAY WILL DIM BETWEEN 22.00
HOURS AND 06.00 HOURS TO PREVENT GLARE.
However, should you operate the timer during these hours the display will
return to normal brightness for a few seconds and then dim again.
SYMBOLS
will light up when you select a Minute Minder Period and will remain
lit for the period set. At the end of the Minute Minder Period, the timer
will emit an audible tone for 2 minutes, the
symbol will start to flash
and will continue to flash until the Minute Minder function is cancelled.
This “Cookpot” symbol will light up either:–
– When you press the Cook Period Button and set a length of time for
an Auto Cooking Programme. (It will go out again a few seconds after
you release the timer buttons).
– During the actual Cook Period.
“AUTO” will light up:–
– When the timer is first turned on it will flash. (It will go out when a
time of day is set.
A
U
T
O
– When an Auto Cooking Programme has been set.
The “Auto” symbol will flash at the end of an Auto Cooking programme
to indicate that the programme has finished.
(When the “Auto” symbol is flashing, to return the oven to Manual
operation, turn the oven controls off, ensure that the correct time
of day is set, and press the “Manual” button twice – The “Auto”
symbol will go out.
TIMER FUNCTION BUTTONS
Minute Minder
Button
Here you can set a time period of up to 23 hours 59 minutes, that will count
down. When it reaches zero, the timer will emit an audible tone.
For Example: If you set 20 minutes, the audible tone will occur 20 minutes
later.
AUTO COOKING PROGRAMME
Cook Period Button
Cook Period is the actual length of time for which, the timer will switch the
oven(s) on as part of an “Auto Cooking” programme.
(e.g. If you set 2 hours, the food will be cooked for 2 hours).
End Time Button
The time of day at which you want an “Auto Cooking” programme to end.
For Example: If you set a “Cook Period” for 2 hours, and “End Time” of
11:00. The timer will switch the oven(s) on at 9:00 and turn the oven(s) off at
11:00. You will hear a audible tone at 11:00, to indicate that the Auto
Cooking Programme has finished.
Notes:
– When setting an Auto Cooking programme you will need to set the oven
controls(s) to the required temperature(s) when you set the timer.
_
If an Auto Cooking programme has been set the oven(s) will only operate
during the pre-programmed time.
Manual Button
Needs to be pressed to cancel an Auto Cooking programme and return the
ovens(s) to Manual operation.
“+” and “–” Buttons
Used to adjust the various timer function settings.
9
ELECTRONIC CLOCK & AUTOMATIC
OVEN TIMER OPERATION
SETTING THE TIME OF DAY
A
U
Step 1 Make sure all oven controls are turned Off.
T
O
Step 2 Check the electricity supply to the cooker is turned on.
Step 3 When switched on the display will show 0.00 and Auto symbol
will be flashing intermittently.
Step 4 Press & hold in both the “Minute Minder” & “Cook Period” button
together.
Step 5 With the “Minute Minder” & “Cook Period” buttons still held in,
press either the “+” or “–” buttons to set the correct time of day.
Step 6 Release all the buttons simultaneously.
THE TIME OF DAY IS NOW SET.
To change the time of day repeat Steps 4, 5 & 6 above.
Note: You cannot adjust the time of day if the timer has been set
for an Auto Cooking Programme.
Bell Symbol
SETTING THE MINUTE MINDER
Step 1 Ensure the time of day is set correctly.
Step 2 Press and hold the Minute Minder Button, a
symbol will light up.
Step 3 With the “Minute Minder” button held in, set the required Minute
Minder Period Time
Minder time using the “+” and “–” buttons.
Release all buttons and the timer display will revert back to the time of day.
Bell symbol will remain lit to signify that a Minute Minder period has been set.
At the end of the set time a bleeping sound will be heard, and the
symbol will flash for approximately 2 minutes.
After approximately 2 minutes the bleeping sound will stop and the
symbol will go out automatically.
Step 4 To cancel the bleeping sound within the two minutes press the
Minute Minder button.
Note 1 When the Minute Minder has been set, the time remaining can be
checked at any time by simply pressing the Minute Minder button.
Note 2 If necessary the Minute Minder can be cancelled before the tone sounds
by pressing and holding the Minute Minder button and then at the same
time pressing the “–” button until 0.00 appears in the display window.
10
ELECTRONIC CLOCK & AUTOMATIC
OVEN TIMER OPERATION
AUTO COOKING PROGRAMMES
There are two Auto Cooking programmes that can be selected using your timer:–
(a) To set the timer to switch the oven(s) On and Off Automatically
(b) To set timer to switch on immediately and OFF automatically after a set cook period.
a) TO SET THE TIMER TO SWITCH THE OVEN(S) ON AND OFF AUTOMATICALLY
This allows you to cook at a specified time for a chosen period before the oven
switches off Automatically.
Step 1 Check that the correct time of day is set, if not follow instructions for setting the
time of day.
Step 2 Place food onto the correct shelf position in the oven and close the oven door(s).
Cooktop Symbol
Step 3 Press and hold in the Cook Period button.
The display will read 0.00 with the cookpot (
) symbol lit.
Step 4 With the Cook Period button still held in, set the required Cook
Period using the “+” and “–” buttons.
A
U
T
Release the buttons and the timer display will revert to the time of day
with the Auto symbol and Cookpot (
) symbol lit.
O
Step 5 Press and hold in the “End Time” button.
The display will read the earliest possible end time for the Cook
Period that you have set above.
A
U
T
O
The Auto symbol and Cookpot (
) symbol lit.
Step 6 With the End Time button still held in, use the “+” and “–”
buttons to set the “End Time” (i.e. The time you require the oven
to switch off).
Release all the buttons and the timer will revert back to the time of day.
The “Auto” symbol will remain lit to signify that an Auto Cooking
A
U
T
O
Programme has been set. The (
) symbol will go out.
Step 7 Turn the oven control(s) to the required temperature, and if
necessary select the appropriate oven function.
Note: If your appliance has two ovens: When the timer has been
set for one oven it is possible to use the other oven only during the
same Automatic programme.
At the end of the Automatic Cook Period the Auto Symbol will flash and
an intermittent bleeping sound will be heard.
The bleeping sound will continue for approximately 2 minutes unless
cancelled. The “Auto” symbol will continue to flash until the timer is
returned to Manual operation (see below).
Step 8 Press the Manual button to cancel the bleeping sound. (If 2
minutes has not elapsed).
Step 9 Turn the oven control(s) to the OFF position.
Step 10Press the manual button again to return the oven(s) to Manual
Operation. (The Auto symbol will go out)
11
ELECTRONIC CLOCK & AUTOMATIC
OVEN TIMER OPERATION
Note 1 When cooking automatically the Cook Period can be checked at any time
by simply pressing the Cook Period button.
Note 2 When cooking automatically the End Time can be checked at any time by
simply pressing the End Time button.
b) TO SET TIMER TO SWITCH ON IMMEDIATELY AND OFF AUTOMATICALLY
AFTER A SET COOK PERIOD
Step 1 Check that the correct time of day is set, if not follow instructions for setting the time
of day.
Step 2 Place food onto the correct shelf position in the oven and close the oven door(s).
Step 3 Turn the oven control(s) to the required temperature, and if necessary select the
appropriate oven function.
Cookpot Symbol
Step 4 Press & hold in the “Cook Period” button, the display will read
0.00 and the cookpot (
) symbol will light up.
With the Cook Period button still held set the required Cook Period
using the “+” and “–” buttons. Example: 1hr 30 minutes (as shown).
Note: Cook Period is the length of time the food requires to cook.
Step 5 Release all buttons.
A
U
T
The timer display will revert to the time of day with the Auto symbol lit &
Cookpot symbol remaining lit.
O
Note: Cookpot symbol disappears
At the end of the Cook Period the “Auto” symbol will flash and an
intermittent bleeping sound will be heard.
The bleeping sound will continue for approximately 2 minutes unless
cancelled. The “Auto” symbol will continue to flash until the timer is
returned to Manual operation (see below).
A
U
T
O
A
U
T
Step 6 Press the manual button to cancel the bleeping.
(If 2 minutes has not elapsed)
O
Step 7 Turn the oven control(s) to the OFF position.
A
Step 8 Press the “Manual” button again to return the cooker to Manual
operation. (The Auto symbol will go out).
12
ELECTRONIC CLOCK & AUTOMATIC
OVEN TIMER OPERATION
TO CANCEL AN AUTO COOKING PROGRAMME BEFORE
THE COOK PERIOD HAS FINISHED.
Step 1 Turn the oven control(s) to the OFF position.
Step 2 Press and hold in the “Cook Period” button.
Step 3 With the “Cook Period” button still held in, return the display to
0.00 by pressing the “–” button.
A
U
T
Step 4 Release the “Cook Period” and “–” buttons and the display will
O
revert to the time of day and the “Auto” symbol will flash.
Step 5 Press the “Manual” button to return the oven(s) to “Manual”
operation. The “Auto” symbol will go out.
Note 1
When cooking automatically the Cook Period can be checked at any time by
simply pressing the Cook Period button.
OTHER NOTES ON TIMER OPERATION
1. When cooking Automatically the Cook Period can be checked at any time simply by pressing
the Cook Period button.
2. When cooking Automatically the End Time can be checked at any time by simply pressing the
End Time button.
3. Having set a Cook Period and End Time an electronic device stores the information. The device
within the timer will switch the oven(s) on and off at the required times.
4. When setting an Auto Cooking Programme and a mistake is made, to clear:–
(a) Press and hold in the “Cook Period” button.
A
U
T
(b) With the Cook Period button still held in, return the display to
by pressing the “–”
O
button.
(c) Release the “Cook Period” & “–” buttons, and the display will revert to the time of day and
the “Auto” symbol will flash.
(d) Press & release the “Manual” button.
(e) Start the sequence again.
5. If at any time the display shows three flashing zero’s 0.00. It is likely that the electricity supply
to the oven has been interrupted. Reset the timer to the correct time of day.
Food in the oven may, therefore, not have been cooked, before serving check food is
thoroughly heated and completely cooked.
6. To set each function always press and hold the required function button and at the
same time press “+” or “–” buttons.
Note: Between the hours of 22.00 & 06.00 the display dims to prevent glare.
However, if you should operate a button during this period, the timer will return to
normal brightness for a few seconds and then dim again.
13
GRILL PAN & HANDLE
The grill pan handle is detachable from the pan, to facilitate cleaning and storage.
The grill pan handle can be fixed as follows:
(d)
(a)
(c)
(b)
Step 1
Step 2
Step 3
Ste
Step 1 Remove screw & washers from the grill pan bracket (a).
Step 2 Tilt the handle over the recess (b).
Step 3 Slide it towards the centre of the pan (c).
Step 4 Locate the handle over the bracket (d).
For a fixed handle, replace screw & washers and ensure they are fully
tightened up. If a detachable handle is required, do not replace screw &
washers.
Note: If a fixed handle is required, the grill pan is unable to be stored in the oven
with the door closed and cannot be used as a meat pan.
GRILL PAN
FOOD GRID
GRILL PAN AND
FOOD GRID
DOOR POSITION FOR
GRILLING
Note:Do not grill with the grill/oven
closed.
14
GRILLING PROCEDURE
B
❍ ❍
A
❍❍❍❍❍❍
Note: DO NOT allow young children near to the appliance when the grill is in use as
the surfaces get extremely hot.
Step 1 Ensure oven timer is set to manual.
Ensure the oven shelf is in the correct position (see Guide to Grilling
Successfully).
Ensure door is in the grilling position (see grilling page)
Step 2 Turn knob (A) clockwise to full or half grill function.
NOTE: Resistance will be felt when turning from fan oven operation to
full / half grill position.
Step 3 Turn knob (B) clockwise to select the Grill Setting (1–6).
(1=Low,
6=High).
NOTE: When using the grill, a gentle flow of air will be detected coming from
beneath the control panel.
Step 4 After use, turn both controls A & B to their off (0) position and close
the oven door.
Notes:
• Ensure oven timer is set to manual.
• Preheat the grill at setting 6 on the grill control for approximately 5 minutes.
• The grill pan must be placed on the correct shelf and positioned centrally
under the grill element.
• Leave the control at 6 for toast, and for fast cooking of foods.
• For thicker foods requiring longer cooking, turn the switch to a lower setting
after the initial sealing on both sides at 6. The thicker the food, the lower the
control should be set.
• If excessive smoke is emitted reduce the setting.
• Do not line the grill pan with aluminium foil as this increases the amount of
fat spitting.
• Ensure that the Grill Pan is cleaned after use. Excessive fat build-up in the
bottom of the pan could cause a fire hazard.
• After use, always return both controls to their OFF (O) position.
15
Fan
Oven
USING THE OVEN FOR FAN COOKING
Since a circulaire fan oven heats up more quickly, and generally cooks food at a lower
temperature than a conventional oven, pre-heating is often unnecessary. For guides on
“pre-heating”, “cooking temperatures” and “cooking times”, see “Oven Temperature
Charts” later in book.
NOTE: Charts are a guide only, to suit personal taste and requirements, it may be
necessary to increase or decrease temperatures by 10˚C. It may also be necessary to
increase or decrease cooking times.
OVEN SHELF POSITIONING FOR FAN OVEN
Most foods will cook satisfactorily on any shelf position, due to even distribution
of heat in the oven, but the shelves must be evenly spaced.
Food or utensils should never be placed directly on the floor of the oven
for cooking as air circulation is restricted.
DO NOT allow young children near to the appliance when the oven is in use as the
surfaces get extremely hot.
OVEN UTENSILS
Do not use:
Meat pans larger than 375mm x 300mm (15” x 12”)
Baking Trays larger than 325mm x 250mm (13” x10”)
An additional oven shelf can be purchased from your oven supplier if a third
one is required for batch baking. Never use more than three shelves in the oven
as air circulation will be seriously restricted.
TEMPERATURE & TIME
If three shelves are in use to cook large quantities of food, it may be necessary
to increase the cooking times given in the temperature charts by a few minutes,
to allow for the loss of heat due to extra time taken to load the oven, and the
larger mass of food. Baking trays should have an even gap around the oven.
16
Fan
Oven
USING THE OVEN FOR FAN COOKING
FAN OVEN OPERATION
B
❍ ❍
A
❍❍❍❍❍❍
Step 1 Ensure oven timer is set to manual.
Ensure that the oven shelf is in the correct position.
Place food centrally on the shelf ensuring the oven door is fully
closed.
Step 2 Turn knob (A) clockwise and select the required cooking
temperature . The pilot light (G) will immediately come on, and
remain on until the oven reaches the required temperature. The light
will then automatically go off and on during cooking as the oven
thermostat maintains the correct temperature.
Step 3 After use turn control (A) to its Off (O) position.
NOTE: At the end of a cooking period there may be a momentary puff of
steam when the door is opened. This will disperse in a few seconds
and is a perfectly normal characteristic of an oven with a good door
seal.
17
USING THE OVEN FOR OTHER FUNCTIONS
“SLOW” SETTING
E
90
This is used for slow cooking, keeping food warm and warming plates for short
periods. Extra care should be taken when warming bone china, as it may be
damaged in a hot oven.
DO NOT place food or plates directly on the oven floor as this could damage both the
oven lining and the plates which are being warmed.
ADVANTAGES OF SLOW COOKING ARE:
The oven stays cleaner because there is less splashing.
Timing of food is not as critical, so there is less fear of overcooking.
Inexpensive joints of meat are tenderised.
Fully loading the oven can be economical.
Cooking times can be extended in some cases by up to 2 hours.
The kitchen stays cooler.
OPERATION:
1. Place the prepared food in the main oven and ensure the door is fully closed.
2. Turn knob A to
(slow cooking temperature).
E
90
STORAGE & RE-HEATING OF FOOD:
1. If food is to be frozen or not used immediately, place it in a clean container and
cool as soon as possible.
2. Always thaw frozen food completely in the refrigerator before re-heating.
3. Always reheat food thoroughly and ensure it is piping hot before serving.
4. Only re-heat food once.
POINTS TO CONSIDER WHEN PREPARING FOOD FOR SLOW COOKING
1. Make sure that the dishes to be used will fit into the oven ensuring enough room
for air to circulate.
2. All dishes cooked on the slow setting will require a minimum of 6 hours,
however, it they are cooked for 1-2 hours longer then deterioration in their
appearance may be noticed.
3. Never cook joints of meat over 2.7kg (6 lb) or poultry over 2.0kg (4lb 8oz).
We do not recommend that joints of meat or poultry are stuffed before cooking
on the slow setting.
4. To seal in the meat juices, always cook meat or poultry at 170oC for 30 minutes
before wrapping in foil and placing on a rack over a tin (to allow good air
circulation) before turning the control to the slow setting and cooking immediately.
5. Always ensure that joints of pork and poultry are thoroughly cooked by checking
with a meat thermometer before serving.
6. Always thaw frozen foods completely before cooking. We do not recommend
placing frozen food in the oven to cook.
7. Always bring soups, liquids and casseroles to the boil before placing in the oven.
8. Ensure that casserole dishes have a good seal (not airtight) and cover to the top
with foil to prevent loss of moisture.
9. Ensure that fruit and vegetables are cut into even sized small pieces to cook
properly.
10. Always adjust seasoning before serving.
11. If using dried red kidney beans it is important that the beans are soaked and
then boiled for a minimum of 10 minutes before using in any dish to destroy any
toxins.
12. When cooking fish or egg dishes it may be necessary to check during cooking to
avoid overcooking.
18
TEMPERATURE CONVERSION SCALE
Main
Conventional
Oven
Main
Fan
Oven
Gas
Mark
o
F
1
250
275
300
325
350
375
400
425
450
475
120
140
150
160
180
190
200
220
–
100
120
130
140
160
170
180
200
210
220
2
/
1
2
3
4
5
6
7
8
9
–
19
OVEN TEMPERATURE CHARTS – MEAT
Fan Oven Cooking
Food
Note: Up to three shelves may be used in this oven. The position
of these is not important providing they are evenly spaced.
Pre- Temperature
Time
Meat
Beef
Lamb
Pork
Veal
o
heat
C
(approx.)
20-25 mins per 450g (1lb)
+ 20 mins extra
No
160/180
25 mins per 450g (1lb)
+ 25 mins extra
No
No
No
No
No
No
No
160/180
160/180
160/170
160/180
150/160
150
25 mins per 450g (1lb)
+ 25 mins extra
25-30 mins per 450g (1lb)
+ 25 mins extra
Chicken/Turkey
up to 4kg (8lb)
18-20 mins per 450g (1lb)
+ 20 mins extra
Turkey up to
5.5kg (12lb)
13-15 mins per 450g (1lb) e.g.
5kg (11lb) = 143-165 mins
Turkey over
5.5kg (12lb)
12 mins per 450g (1lb) e.g.
10kg (22lb) = 264 mins
Casserole /
Stews
A140/150
11⁄2 - 2 hours
IF USING ALUMINIUM FOIL
1. Never allow foil to touch sides of oven. 2. Never cover interior with foil.
3. Never cover shelves with foil.
The most accurate method of testing the readiness of joints of meat or whole
poultry is to insert a meat thermometer into the thickest part of a joint of meat,
or the thickest part of poultry thighs, during the cooking period. The meat
thermometer will indicate when the required internal temperature has been
reached.
Beef
Pork
Lamb
Poultry
Veal
Rare 60OC
Medium 70OC Well Done 75OC
90OC
80OC
90OC
75OC
20
OVEN TEMPERATURE CHARTS –
BAKING
Fan Oven Cooking
Baking
Note: Up to three shelves may be used in this oven. The position
of these is not important providing they are evenly spaced.
Pre- Temperature
Food
Time
o
heat
C
Scones
Yes
210/220
9-12 mins
15-25 mins
Small Cakes
No
No
170/180
160/170
170/190
180/200
140/150
130/140
190/200
190/200
180/190
190/200
130/140
140/150
200/210
70/90
Victoria
Sandwich
Sponge Sandwich
(Fatless)
20-25 mins
Yes
Yes
No
15-20 mins
Swiss Roll
12-15 mins
Semi-rich
Fruit Cake
11⁄4-11⁄2 hours
Rich Fruit Cakes No
Time depending on use
Time depending on use
Time depending on use
40-45 mins
Shortcrust
No
Pastry
Puff Pastry
No
Yes
Yes
No
Yorkshire
Pudding
Individual Yorkshire
Pudding
20-45 mins
Milk Pudding
Baked Custard
Bread
11⁄2-2 hours
No
35-45 mins
Yes
No
20-30 mins
Meringues
3-4 hours
Note: If soft tub margarine is being used for cake making, we would recommend using the
O
all in one method and to reduce the temperature by 10 C. Temperatures recommended in
this chart refer to cakes made with block margarine or butter only.
21
COOKING RESULTS NOT
SATISFACTORY
GRILL
Uneven cooking front to back
Ensure that the grill pan is positioned centrally
below the grill element.
Fat splattering
Ensure that the grill pan is not lined with foil.
Ensure that the grill setting is not too high.
BAKING GENERAL
Uneven rising of cakes
Sinking of cakes
Ensure that the oven shelves are level.
The following may cause cakes to sink:
1. Pre-heating of fan ovens – not always necessary.
2. Cooking at too high a temperature – reduce
standard temperatures by 25˚C for fan ovens.
3. Using normal creaming method with a soft
margarine. If using soft margarine, use an all in
one method instead of the traditional creaming of
the margarine and sugar. Remember when using a
food mixer or processor not to over-cream soft
margarine.
Over/undercooking
Refer to the cooking times and temperatures given in
the Oven Temperature Charts provided, however, it
may be necessary to increase or decrease
temperatures by 10˚C to suit personal taste.
l
4
Do not use utensils greater than 56mm (2⁄ '') in height
for roasting.
22
CARE AND CLEANING
Warning: Before cleaning, please ensure that the electricity supply to the appliance is
switched off and the appliance is fully cold.
1. “STAYCLEAN” OVEN LINERS
(a) How "Stayclean" works.
The surfaces of the "Credaclean" oven liners are
treated with a special vitreous enamel which absorbs
cooking soils. At temperatures of 220°C (425°F) or
above, the special surface enables these soils to be
slowly destroyed.
The higher the temperature the more effective it is.
(b) Cleaning.
In most cases normal cooking operations at 220°C
(425°F) will permit this cleaning operation to proceed
during cooking. However if higher cooking
temperatures are not used regularly, it may be
necessary, in order to prevent heavy soiling, to run the
ovens without shelves or meat pan, at a maximum
setting for a couple of hours. It should not normally be
necessary to clean the "Stayclean" panels with water.
If the user feels it is desirable to do so, wipe them over
with a clean, soapy cloth, followed by a wipe with a
clean damp cloth.
MAIN OVEN SIDE LINERS
AND REAR PANEL
DO NOT use biological washing powder, harsh
abrasives or chemical oven cleaners of any kind as this
could damage the “Stayclean” oven liners.
23
CARE AND CLEANING
2. CLEANING THE OVEN
(a) Base of Main Oven.
Wipe out the oven with a damp soapy cloth. For
more stubborn stains on the base of the oven use a
well soaped fine steel wool soap pad.
REMOVABLE GRILL ROOF PANEL
(NOT ALL MODELS OR MODELS
FITTED WITH HIGH SPEED GRILL)
(b) Grill/Meat Pan & Oven Shelves.
To prevent stains from being burnt on to the grill pan,
food support and rod shelf, always wash immediately
after use in hot soapy water.
Use a well soaped fine steel wool soap pad to
remove stubborn stains from the rod shelves,
grill/meat pan and the base of the oven.
OVEN
SHELVES
GRILL/
MEAT
PAN
MAIN
OVEN
BASE
DO NOT use aerosol cleaners on this oven as they
could adversely affect the fan motor unit, and cannot
be wiped off the fan blade.
(c) Removable Grill Roof Panel (not all models).
Pull grill roof panel out slowly, being careful not to
damage the elements. Clean using a damp soapy
cloth, if stubborn stains remain gently clean with a
well soaped fine steel wool soap pad and soapy
water, and then wipe over with a damp cloth.
(d) Solarplus Grill (not all models).
To clean the Solarplus grill, use a clean, damp, soapy
cloth and wipe over. If stubborn stains remain, gently
clean with a well soaped nylon scouring pad and wipe
over with a damp cloth.
DO NOT use metal cleaning utensils, wire wool or
proprietary oven cleaners on the grill element mesh.
24
CARE AND CLEANING
3. CONTROL PANEL / TRIMS / INNER DOOR PANEL & GLASS
(a) Control Panel
OVEN
DOOR
Regularly wipe with a clean, damp cloth and polish
with a clean, dry cloth.
(b) Trims
It is advisable to clean the trims regularly to prevent
any build up of soiling which may detract from the
appearance of the cooker. The recommended
method of cleaning is to wipe over the trims with a
clean, soft cloth wrung out in hot water, or mild non
abrasive cleaner. (If in doubt try the cleaner on a
small area of trim which is not noticeable in normal
use), then after wiping with a cloth wrung out in
clear water, dry with a clean, soft cloth.
(c) Inner Door Panels & Glass
Open the door fully. The glass panel may now be
washed. Stubborn stains can be removed by using a
well soaped, fine steel wool soap pad.
TRIMS
DO NOT use scouring pads, or abrasive powder,
which will scratch the glass.
4. RE OVEN LAMP
Warning: Before removing lamp lens, please ensure
that the electricity supply to the appliance is
switched off and the appliance is fully cold.
Open the oven door and remove the oven shelves.
Using a thick cloth, grip the lamp lens, unscrew anti-
clockwise and remove the lens.
Carefully unscrew the bulb anti-clockwise. Fit
replacement bulb (25W 300°C SES). Fit replacement
bulb and refit lens.
MAIN OVEN LAMP
5. HOW TO CLEAN THE LAMP LENS
Warning: Before cleaning lamp lens, please ensure
that the electricity supply to the appliance is
switched off and the appliance is fully cold.
Open the oven door and remove the oven shelves.
Using a thick cloth, grip the lamp lens, unscrew anti-
clockwise and remove. Clean with a non-abrasive
cleansing cream and refit lamp lens.
DO NOT use scouring pads, or abrasive powder,
which will scratch the glass lens
MAIN OVEN LAMP
25
CARE AND CLEANING
Take particular care not to damage the inner surface of the door inner
glass that is coated with a heat reflective layer. Do not use scouring pads,
or abrasive powder, which will scratch the glass. Ensure that the glass
panel is not subjected to any sharp mechanical blows.
Stubborn stains can be removed by using a fine steel wool pad. For slight soiling
the inner glass panel may be cleaned, while still warm, without removing it from
the door. After cleaning, rinse and dry with a soft cloth.
CLEANING THE DOORS
SIDE OPENING DOORS
Cleaning the door glass is the same as the drop down doors, except take
care to support the weight of the inner glass when removing and refitting.
DROP DOWN DOORS
Remove the door inner glass as follows.
1. Open the door fully and unscrew the two screws securing the glass panel so
that the securing brackets can be turned. There is no need to remove the screws
completely.
2. Turn the brackets so that the glass can be
removed and cleaned at the sink (Fig. 1.)
Fig. 1.
Glass
3. The inside of the outer door glass can now be cleaned while still fitted to the
cooker.
NEVER OPERATE THE COOKER WITHOUT THE INNER DOOR
GLASS IN POSITION.
Refit the door inner glass as follows.
1. NOTE: The inner door glass has a special reflective coating on one side.
Replace the door inner glass so that the statement: “IMPORTANT THIS FACE
TOWARDS THE OVEN” can be read from the inner side of the door.
2. Turn the two securing brackets back to their
original position to retain the glass and tighten
the screws. (Fig. 2.)
Fig. 2.
Glass
26
INSTALLATION INSTRUCTIONS
IMPORTANT
This equipment is designed specifically for domestic purposes and Hotpoint LTD
cannot accept responsibility if used in any other type of installation.
This appliance must not be installed over any appliance that generates heat.
For your own safety, we recommend that your appliance is installed by a competent
person – such as one who is registered with NICEIC (National Inspection Council
for Electrical Installation Contracting). The cooker should be installed in accordance
with the latest Edition of the IEE Regulations.
1. GENERAL
WARNING: THIS APPLIANCE MUST BE EARTHED.
(a) The oven unit is designed for mounting at a safe level into an oven housing
which must be secured to the backing wall, or alternatively, in the case of the
single oven unit, under a worktop with or without a hob unit above.
(b) In an oven/hob arrangement where it is proposed to install the oven directly
below the hob. It is advisable that only slimline hobs are used which have the
following maximum depths.
Maximum hob depth
Kitchen Worktop thickness
(from worktop surface vertically down)
30mm
40mm
55mm
65mm
Worktop thickness + 25mm
40mm +
It is most important that the hob installation instructions are strictly observed.
27
INSTALLATION INSTRUCTIONS
2. OVEN UNIT HOUSING CABINETS
(a) The oven unit housing cabinet dimensions must comply with Fig. 3 and
Fig. 4.
(b) An air gap of 50mm minimum must be provided at the rear of any top or
bottom cupboards or shelves for ventilation.
(c) Do not obstruct the ventilation slots provided on the oven trim. This is found
adjacent to the bottom of the oven door.
(d) The air gap at the rear allows the warmed air to pass out of the cabinet. If
cabinets extend up to the ceiling, the warm air must be exhausted through
to the front. Fig. 1.
(e) If an oven unit is installed adjacent to a tall cabinet, steam escaping from the
oven when the door is opened could condense on, and perhaps stain the
adjacent surface. To prevent permanent staining, the adjacent surface
should be made of a material that is heat resisting and easy to clean.
Adjacent tall cabinets should not be deeper than the oven housing cabinet.
IMPORTANT
It is essential that the lower cupboard is constructed in the manner illustrated i.e.
having side, back and roof panels so joined as to provide no apertures which could
permit access to the oven unit when installed.
3. ELECTRICAL INSTALLATION
Mains Supply
A 20 amp Double Pole control switch with a minimum contact clearance of 3mm
must be fitted on or recessed in the wall adjacent to the oven housing cabinetry
and should be accessible after installation. If the oven is to be wired into a con-
nector unit this may be positioned behind the oven providing:–
i. The top of the connector unit is not more than 30cm above the base of the
oven recess – see Fig. 4.
ii. The depth of the connector unit does not reduce the depth of the oven
recess to less than 55cm.
We recommend that 4mm2 twin and earth PVC insulated cable is used to connect
the cooker to the control unit. This power supply cable must conform to BS 6004.
Alternatively the mains supply can be taken from a household 13 amp switched
fused spur. Having a minimum contact clearance of 3mm which must be fitted
adjacent to the oven housing cabinetry and accessible after installation. The oven
must be fitted with a 3 core cable having a minimum cross sectional area of
1.5mm2 and must conform to BS6500.
The oven must not be connected using a 3 pin 13 amp plug.
28
INSTALLATION INSTRUCTIONS
Any spare cable must be coiled either behind the oven (not more than 30cm above the
base of the oven recess) or pushed into the air gap below the oven after installation.
Where a hob is fitted adjacent to or above an oven a 30 amp or 45 amp double pole switch
with a minimum contact clearance of 3mm should be used to feed both units via separate
suitably rated cables.
Where a hob unit is fitted above the oven unit we recommend that 85oC High Temperature
PVC with insulated 3 core flexible cord to table 15 of BS 6141:1991 with a conductor size
of 2.5mm2 must be used to connect the hob to the control unit.
Where a hob unit is fitted adjacent to the oven unit, then 4mm2 twin and earth cable to BS
6004 is recommended to connect the hob unit to the control unit.
In all cases adhere to routing details (see fig. 5).
Your cooker should have been checked to ensure that the voltage corresponds with your
supply voltage, this is stated on the rating plate which is located on the oven front frame
(lower).
CONDUIT BOX TO MAINS TERMINAL BLOCK
(a) The oven unit should be placed on the floor on its carton base in front of the
housing cabinet. The rear of the unit should be in line with the conduit box.
(b) Ensure there is sufficient cable for any future servicing.
(c) Remove the terminal cover. Prepare the cable, pass it through the cable
entry hole in the oven rear panel and fit to terminal block. Secure the cable
clamp and replace the terminal cover.
4. FINAL INSTALLATION
(a) Using a spirit level, check that the housing cabinet is level from side to side and
from front to back in its installed position.
(b) Correct any unevenness by placing spacers under the bottom of the cabinet.
Make sure that the cabinet rests firmly on the floor without rocking.
(c) Before the oven is fitted the cabinet must be firmly secured to the backing wall
for stability.
(d) The oven unit should now be lifted (this requires two people) into the cabinet
and pushed fully home.
(e) Finally the oven unit must be secured to the cabinet. Position the oven side trims
equally about the cabinet sides. This should give an overlap of approx. 1.5mm
per side (see Fig. 2). Secure the oven unit to the cabinet, through the side trims,
by means of the four screws provided, two each side trim.
(f) Remove all packing material from the grill and oven interior.
LIST OF LOOSE ITEMS
4 x No.6 Pozi Head screws
29
INSTALLATION INSTRUCTIONS
Ventilation Slot
if cabinet doesn't fit to ceiling
560mm
Ventilation Slot
if cabinet fits
to ceiling
50mm
air
gap
Fig. 1
Viewed down through
cabinet
Oven
Fig. 2
Cabinet
50mm
air
gap
Tall Cabinet
Side
Trim
When fitting a hob above an oven always
use these installation instructions
in conjunction with the hob instructions.
Use 2.5mm2 High Temp Cable. Refer to
Electrical Installation.
Oven Door
No. 6 x 15mm
(4 Supplied)
1.5mm
Fig. 3
Built
Under
578mm min
585mm max
30
INSTALLATION INSTRUCTIONS
Fig. 4
Single Oven
in tall
Cabinet
Double Pole
585mm max
578mm if cooker
trim is to
Control Switch
6mm2 Cable if Hotplate
fitted
overlap
top edge
of shelf
Conduit Box
4mm2 Cable if hob fitted
adjacent to oven
*excluding pipes
and other
projections
4mm2 Cable
to Oven
Refer to Electrical Installation
Fig. 5
31
SOMETHING WRONG?
Before calling a Service Engineer, please check through the following lists.
THERE MAY BE NOTHING WRONG.
Problem
Check
Nothing works.
(a) Check
If you find :-
Display is blank. (BS41)
Then it is likely that there is no electricity supply to your
oven.
Check: (i) That the main cooker wall switch is turned on.
(ii) Check other appliances to see if you have a power
cut.
(iii) Check the main circuit breaker for the property.
(iv) With the selector switch (A) turned to
light does not illuminate.
the oven
Display shows 0.00 AUTO.
(BS41)
The power supply to your oven has possibly been interrupted, but
has now come back on again. Reset the timer to the correct time
of day and "Manual" operation using instructions given in the
timer section of the book.
Fan oven does not work but the
grill works.
Check to ensure that the timer is in Manual Mode:
See timer section for instructions on how to return timer to
"Manual".
Operating the cooker under the following conditions may cause a
safety device to operate.
Fan Oven and Grill do not work.
(a) Grilling with the door closed - always grill with the door open
to the correct position - see grilling.
(b) Grilling for an excessively long period at maximum setting -
see grilling guide.
(c) Grilling with inadequate ventilation in the cabinet - see
installation instructions.
Check that you have selected :- "Grill" function on the "Fan
oven/Grill Select" knob (A) and a Grill setting on theGrill Knob (B)
- see grilling page.
Grill does not work.
When the Grill control (B) is operating at less than "6", the grill will
cycle on and off, this is normal and is not a fault.
Grill keeps turning on and off.
Remember: "Cook Period" is the actual length of time for which,
the timer will switch the oven on as part of an "Auto Cooking"
programme.
Can not set an “Auto Cook” pro-
gramme (BS41)
Draught from beneath control
panel.
A gentle flow of air will be blown from beneath the control panel
when the appliance is used.
Buzzer/Bleeper should stop automatically after 2 minutes (BS41)
4 minutes (BS31). If not, press minute minder
button to silence.
Timer buzzer/bleeper operates
continually
If you have been through the above list and there is still a problem; You should identify
yourService Agent using the list on the back page and contact your Local Service Office.
32
Key Contacts
Service
Hotpoint has the largest appliance manufacturer’s service team in
Europe, trained specialists directly employed by us to ensure your
complete confidence.
Repair Service
UK: 08709 066 066
Republic of Ireland: 1850 302 200
You will be asked for the following information:-
Name, address and postcode.
Telephone number
Model / Serial number of the appliance
Clear and concise details of the query or fault
Place and Date of purchase
(Please keep the receipt as evidence will be required when the engineer calls).
Extended Warranty
To join: UK 08709 088 088
Republic of Ireland: 1850 502 200
Genuine Parts & Accessories
Mail Order Hotline
UK: 08709 077 077
Republic of Ireland: (01) 842 6836
For further product information 08701 50 60 70
All Hotpoint Services are offered as an extra benefit and do not affect your statutory rights.
General Domestic Appliances Limited, Morley Way, Peterborough, PE2 9JB
.
PRINTED BY SIMLEX FOUR ASHES, WOLVERHAMPTON.
May 1999 Part No. 481900022-01
|