Hotpoint Oven GP641X User Manual

Operating Instructions  
HOB  
Contents  
GB  
Installation, 2-5  
Positioning  
Gas connection  
GB  
Data plate  
English,1  
Burner and nozzle specifications  
Electrical connection, 6  
Description of the appliance, 7  
Overall view  
Start-up and use, 8  
Practical advice on using the burners  
Precautions and tips, 9  
General safety  
Disposal  
Recycling & Disposal Information  
GP641X  
Maintenance and care, 10  
Switching the appliance off  
Cleaning the appliance  
Gas tap maintenance  
Troubleshooting, 11  
After Sales Service, 12  
Guarantee, 13  
08448 24 24 24  
Please phone us on  
 
guarantee  
to activate your  
Front  
! Check that the pressure of the gas supply is consistent  
with the values indicated in Table 1 (“Burner and nozzle  
specifications”). This will ensure the safe operation and  
longevity of your appliance while maintaining efficient  
energy consumption.  
GB  
Connection with a rigid pipe (copper or steel)  
! Connection to the gas system must be carried out in such  
a way as not to place any strain of any kind on the  
appliance.  
Hooking position  
Back  
There is an adjustable L-shaped pipe fitting on the  
appliance supply ramp and this is fitted with a seal in  
order to prevent leaks. The seal must always be replaced  
after rotating the pipe fitting (seal provided with  
appliance). The gas supply pipe fitting is a threaded 1/2  
gas cylindrical male attachment.  
for top H=40 mm  
! Use the hooks contained in the “accessory pack”  
• Where the hob is not installed over a built-in oven, a  
wooden panel must be installed as insulation. This must  
be placed at a minimum distance of 20 mm from the  
lower part of the hob.  
Connecting a flexible jointless stainless steel pipe to a  
threaded attachment  
Ventilation  
To ensure adequate ventilation, the back panel of the  
cabinet must be removed. It is advisable to install the oven  
so that it rests on two strips of wood, or on a completely flat  
surface with an opening of at least 45 x 560 mm (see  
diagrams).  
The gas supply pipe fitting is a threaded 1/2 gas cylindrical  
male attachment.  
These pipes must be installed so that they are never longer  
than 2000 mm when fully extended. Once connection has  
been carried out, make sure that the flexible metal pipe  
does not touch any moving parts and is not compressed.  
! Only use pipes and seals that comply with current national  
regulations.  
560 mm.  
Checking the tightness of the connection  
! When the installation process is complete, check the pipe  
fittings for leaks using a soapy solution. Never use a flame.  
Adapting to different types of gas  
To adapt the hob to a different type of gas other than default  
type (indicated on the rating plate at the base of the hob or  
on the packaging), the burner nozzles should be replaced  
as follows:  
When installing the cooktop above a built-in oven  
without forced ventilation, ensure that there are air  
inlets and outlets for ventilating the interior of the  
cabinet adequately.  
1. Remove the hob grids and slide the burners off their  
seats.  
2. Unscrew the nozzles using a 7 mm socket spanner, and  
replace them with nozzles for the new type of gas (see  
table 1 “Burner and nozzle characteristics”).  
3. Reassemble the parts following the above procedure in  
the reverse order.  
4. Once this procedure is finished, replace the old rating  
sticker with one indicating the new type of gas used.  
Sticker are available from any of our Service Centres.  
Gas connection  
The appliance should be connected to the main gas  
supply or to a gas cylinder in compliance with current  
national regulations. Before carrying out the connection,  
make sure the cooker is compatible with the gas supply  
you wish to use. If this is not the case, follow the  
instructions indicated in the paragraph “Adapting to  
different types of gas.”  
• Adjusting the burners’ primary air :  
Does not require adjusting.  
When using liquid gas from a cylinder, install a pressure  
regulator which complies with current national regulations.  
PLEASE PHONE US TO REGISTER YOUR APPLIANCE AND ACTIVATE YOUR PARTS GUARANTEE ON 08448 24 24 24  
3
 
• Setting the burners to minimum:  
GB  
1. Turn the tap to the low flame position.  
2. Remove the knob and adjust  
the adjustment screw, which is  
positioned in or next to the tap  
pin, until the flame is small but  
steady.  
3. Having adjusted the flame to the required low setting,  
while the burner is alight, quickly change the position of  
the knob from minimum to maximum and vice versa  
several times, checking that the flame does not go out.  
4. Some appliances have a safety device (thermocouple)  
fitted. If the device fails to work when the burners are  
set to the low flame setting, increase this low flame  
setting using the adjusting screw.  
5. Once the adjustment has been made, replace the seals  
on the by-passes using sealing wax or a similar  
substance.  
! If the appliance is connected to liquid gas, the regulation  
screw must be fastened as tightly as possible.  
! Once this procedure is finished, replace the old rating  
sticker with one indicating the new type of gas used.  
Stickers are available from any of our Service Centres.  
! Should the gas pressure used be different (or vary slightly)  
from the recommended pressure, a suitable pressure  
regulator must be fitted to the inlet pipe (in order to comply  
with current national regulations).  
DATA PLATE  
Electrical  
see data plate  
connections  
This appliance conforms to the following  
European Economic Community directives:  
- 2006/95/EEC dated 12/12/06 (Low  
Voltage) and subsequent amendments  
- 2004/108/EEC dated 15/12/04  
(Electromagnetic Compatibility) and  
subsequent amendments  
- 93/68/EEC dated 22/07/93 and  
subsequent amendments.  
- 2009/142/EEC dated 30/11/09 (Gas) and  
subsequent amendments.  
- 2002/96/EC and subsequent  
amendments.  
PLEASE PHONE US TO REGISTER YOUR APPLIANCE AND ACTIVATE YOUR PARTS GUARANTEE ON 08448 24 24 24  
4
 
Burner and nozzle specifications  
GB  
Table 1  
Liquid Gas  
Naturale Gas  
Burner  
Diameter Thermal Power By-pass Nozzle  
Flow*  
g/h  
Nozzle  
1/100  
Flow*  
l/h  
(mm)  
kW (p.c.s.*)  
1/100  
(mm)  
1/100  
(mm)  
86  
Nom.  
Red.  
0.70  
***  
**  
(mm)  
116  
Fast  
(Large) (R)  
100  
75  
3.00  
1.65  
1.00  
39  
28  
28  
218  
120  
73  
214  
286  
157  
95  
Semi Fast  
(Medium) (S)  
0.40  
0.40  
64  
50  
118  
71  
96  
71  
Auxiliary  
(Small) (A)  
55  
Nominal (mbar)  
Minimum (mbar)  
Maximum (mbar)  
28-30  
20  
35  
37  
25  
45  
20  
17  
25  
Supply  
pressures  
*
At 15°C and 1013 mbar-dry gas  
**  
***  
Propane  
Butane  
Natural  
P.C.S. = 50.37 MJ/kg.  
P.C.S. = 49.47 MJ/kg.  
P.C.S. = 37.78 MJ/m3  
A
R
S
S
GP641X  
PLEASE PHONE US TO REGISTER YOUR APPLIANCE AND ACTIVATE YOUR PARTS GUARANTEE ON 08448 24 24 24  
5
 
Electrical Connection  
Power supply voltage and frequency: 220-240V a.c.  
50/60Hz.  
Disposing of the plug  
GB  
Ensure that before disposing of the plug itself, you  
make the pins unusable so that it cannot be  
accidentally inserted into a socket. Instructions for  
connecting cable to an alternative plug:  
! The supply cable must be positioned so that it  
never reaches at any point a temperature 50°C  
higher than the room temperature. The cable must  
be routed away from the rear vents. Should you  
require it, you may use a longer cable, however, you  
must ensure that the cable supplied with the  
appliance is replaced by one of the same  
specifications in accordance with current standards  
and legislation.  
! The wires in the mains lead are coloured in  
accordance with the following code:  
Green & Yellow  
Blue  
Brown  
- Earth  
- Neutral  
- Live  
If the colours of the wires in the mains lead do not  
correspond with the coloured markings identifying  
the terminals in your plug, proceed as follows:  
Connect Green & Yellow wire to terminal marked “E”  
Your appliance is supplied with a 13 amp fused plug  
that can be plugged into a 13 amp socket for  
immediate use. Before using the appliance please  
read the instructions below.  
or  
or coloured Green or Green & Yellow.  
Connect Brown wire to terminal marked “L” or  
coloured Red.  
! THIS APPLIANCE MUST BE EARTHED.  
THE FOLLOWING OPERATIONS SHOULD BE  
CARRIED OUT BY A QUALIFIED ELECTRICIAN.  
Connect Blue wire to terminal marked “N” or  
coloured Black.  
If a 13 amp plug (BS 1363) is used it must be fitted  
with a 13 amp fuse. A 15 amp plug must be  
protected by a 15 amp fuse, either in the plug or  
adaptor or at the distribution board. If you are in any  
doubt about the electrical supply to your machine,  
consult a qualified electrician before use.  
Replacing the fuse  
When replacing a faulty fuse, a 13 amp ASTA  
approved fuse to BS 1362 should always be used,  
and the fuse cover re-fitted. If the fuse cover is lost,  
the plug must not be used until a replacement is  
obtained.  
How to connect an alternative plug  
The wires in this mains lead are coloured in  
accordance with the following code:  
Replacement fuse covers  
If a replacement fuse cover is fitted, it must be of  
the correct colour as indicated by the coloured  
marking or the colour that is embossed in words on  
the base of the plug. Replacements can be obtained  
directly from your nearest Service Depot.  
BLUE  
BROWN  
“NEUTRAL” (“N”)  
“LIVE” (“L”)  
GREEN AND YELLOW “EARTH” (“E”)  
GREEN &  
YELLOW  
Removing the plug  
13 amp fuse  
BROWN  
If your appliance has a non-rewireable moulded plug  
and you should wish to remove it to add a cable  
extension or to re-route the mains cable through  
partitions, units etc., please ensure that either:  
• the plug is replaced by a fused 13 amp re-  
wireable plug bearing the BSI mark of approval.  
or:  
CROSS-BAR  
CORD GRIP  
BLUE  
• the mains cable is wired directly into a 13 amp  
cable outlet, controlled by a switch, (in  
compliance with BS 5733) which is accessible  
without moving the appliance.  
Disposing of the appliance  
When disposing of the appliance please remove the  
plug by cutting the mains cable as close as  
possible to the plug body and dispose of it as  
described above.  
Please note: for appliances with a rating greater  
than 13 amp (eg: electric hob, double ovens and  
freestanding electric cookers etc.) the mains cable  
must be wired into a cooker output point with a  
rating of 45 amp. In this case the cable is not  
supplied.  
PLEASE PHONE US TO REGISTER YOUR APPLIANCE AND ACTIVATE YOUR PARTS GUARANTEE ON 08448 24 24 24  
6
 
Description of the  
appliance  
Overall view  
GB  
GAS BURNERS  
Support Grid for  
COOKWARE  
Control Knobs for  
GAS BURNERS  
SAFETY  
DEVICES *  
Ignition for  
GAS BURNERS *  
GAS BURNER ignition* enables a specific burner  
GAS BURNERS differ in size and power. Use the  
diameter of the cookware to choose the most  
appropriate burner to cook with.  
to be lit automatically.  
SAFETY DEVICE* stops the gas flow if the flame  
is accidentally extinguished.  
• Control Knobs for GAS BURNERS adjust the  
power or the size of the flame.  
Only available on certain models.  
*
PLEASE PHONE US TO REGISTER YOUR APPLIANCE AND ACTIVATE YOUR PARTS GUARANTEE ON 08448 24 24 24  
7
 
Start-up and use  
Practical advice on using the burners  
! The position of the corresponding gas burner or  
electric hotplate* is shown on every knob.  
GB  
To ensure the burners operate efficiently:  
Gas burners  
• Use appropriate cookware for each burner (see  
table) so that the flames do not extend beyond  
the bottom of the cookware.  
Each burner can be adjusted to one of the following  
settings using the corresponding control knob:  
Off  
• Always use cookware with a flat base and a cover.  
Maximum  
Minimum  
• When the contents of the pan reach boiling point,  
turn the knob to minimum.  
To light one of the burners, hold a lit match or lighter  
near the burner and, at the same time, press down  
and turn the corresponding knob anti-clockwise to the  
maximum setting.  
Since the burner is fitted with a safety device, the  
knob should be pressed for approximately 2-3  
seconds to allow the automatic device keeping the  
flame alight to heat up.  
Burner  
Ø Cookware Diameter (cm)  
Fast (R)  
24 - 26  
16 - 20  
10 - 14  
Semi Fast (S)  
Auxiliary (A)  
To identify the type of burner, refer to the designs in  
the section entitled, "Burner and Nozzle  
Specifications".  
Some models are equipped with an ignition switch  
incorporated into the control knob. If this is the case,  
the ignitor is present (the  
near each knob).  
symbol is located  
To light a burner, simply press the corresponding  
knob all the way in and then turn it in the counter-  
clockwise direction to the "High" setting, keeping it  
pressed in until the burner lights.  
! If a flame is accidentally extinguished, turn off the  
control knob and wait for at least 1 minute before  
trying to relight it.  
To switch off the burner, turn the knob in a clockwise  
direction until it stops (when reaches the “•” position).  
PLEASE PHONE US TO REGISTER YOUR APPLIANCE AND ACTIVATE YOUR PARTS GUARANTEE ON 08448 24 24 24  
8
 
Precautions and tips  
! This appliance has been designed and  
• Do not let children play with the appliance.  
• The appliance should not be operated by people  
(including children) with reduced physical,  
sensory or mental capacities, by inexperienced  
individuals or by anyone who is not familiar with  
the product. These individuals should, at the very  
least, be supervised by someone who assumes  
responsibility for their safety or receive  
preliminary instructions relating to the operation of  
the appliance.  
GB  
manufactured in compliance with international safety  
standards. The following warnings are provided for  
safety reasons and must be read carefully.  
General safety  
This is a class 3 built-in appliance.  
Gas appliances require regular air exchange to  
maintain efficient operation. When installing  
the hob, follow the instructions provided in the  
paragraph on “Positioning” the appliance.  
These instructions are only valid for the  
countries whose symbols appear in the manual  
and on the serial number plate.  
The appliance is not intended to be operated  
by means of an external timer or separate  
remote-control system.  
Disposal  
• The appliance was designed for domestic use  
inside the home and is not intended for  
• When disposing of packaging material: observe  
local legislation so that the packaging may be  
reused.  
commercial or industrial use.  
• The appliance must not be installed outdoors, even  
in covered areas. It is extremely dangerous to  
leave the appliance exposed to rain and storms.  
• Do not touch the appliance with bare feet or with  
wet or damp hands and feet.  
The appliance must be used by adults only for  
the preparation of food, in accordance with the  
instructions outlined in this booklet. Any other  
use of the appliance (e.g. for heating the room)  
constitutes improper use and is dangerous.  
The manufacturer may not be held liable for  
any damage resulting from improper, incorrect  
and unreasonable use of the appliance.  
• Ensure that the power supply cables of other  
electrical appliances do not come into contact  
with the hot parts of the oven.  
• The European Directive 2002/96/EC on Waste  
Electrical and Electronic Equipment (WEEE),  
requires that old household electrical appliances  
must not be disposed of in the normal unsorted  
municipal waste stream. Old appliances must be  
collected separately in order to optimise the  
recovery and recycling of the materials they  
contain and reduce the impact on human health  
and the environment. The crossed out “wheeled  
bin” symbol on the product reminds you of your  
obligation, that when you dispose of the  
appliance it must be separately collected.  
Consumers may take their old appliance to public  
waste collection areas, other communal collection  
areas, or if national legislation allows return it to a  
retailer when purchasing a similar new product.  
All major household appliance manufacturers are  
active in the creation of systems to manage the  
collection and disposal of old appliances.  
• The openings used for ventilation and dispersion  
of heat must never be covered.  
• Always make sure the knobs are in the “”/“”  
position when the appliance is not in use.  
• When unplugging the appliance always pull the plug  
from the mains socket, do not pull on the cable.  
• Never carry out any cleaning or maintenance work  
without having detached the plug from the mains.  
• In case of malfunction, under no circumstances  
should you attempt to repair the appliance  
yourself. Repairs carried out by inexperienced  
persons may cause injury or further  
Recycling & Disposal Information  
As part of Hotpoint's continued commitment to  
helping the environment, Hotpoint reserves the right  
to use quality recycled components to keep down  
customer costs and minimise material wastage.  
Please dispose of packaging and old appliances  
carefully.  
malfunctioning of the appliance. Contact a Service  
Centre (see Assistance).  
• Always make sure that pan handles are turned  
towards the centre of the hob in order to avoid  
accidental burns.  
• Do not close the glass cover (if present) when the  
gas burners are still hot.  
To minimise risk of injury to children, remove the  
door, plug and cut mains cable off flush with the  
appliance. Dispose of these parts separately to  
ensure that the appliance can no longer be plugged  
into a mains socket, and the door cannot be locked  
shut.  
• Do not use unstable or deformed pans.  
PLEASE PHONE US TO REGISTER YOUR APPLIANCE AND ACTIVATE YOUR PARTS GUARANTEE ON 08448 24 24 24  
9
 
Maintenance and care  
Gas tap maintenance  
Switching the appliance off  
GB  
Over time, the taps may become jammed or difficult to  
turn. If this happens, the tap must be replaced.  
Disconnect your appliance from the electricity supply  
before carrying out any work on it.  
! This procedure must be performed by a  
qualified technician authorised by the  
manufacturer.  
Cleaning the appliance  
! Do not use abrasive or corrosive detergents such as  
stain removers, anti-rust products, powder detergents  
or sponges with abrasive surfaces: these may scratch  
the surface beyond repair.  
! Never use steam cleaners or pressure cleaners on  
the appliance.  
• It is usually enough to wash the hob with a damp  
sponge and dry it with absorbent kitchen roll.  
• The removable parts of the burners should be  
washed frequently with warm water and soap and  
any burnt-on substances removed.  
• For hobs which ligth automatically, the terminal part  
of the electronic instant lighting devices should be  
cleaned frequently and the gas outlet holes should  
be checked for blockages.  
• Stainless steel can be marked by hard water that  
has been left on the surface for a long time, or by  
aggressive detergents containing phosphorus.  
After cleaning, rinse and dry any remaining drops  
of water.  
PLEASE PHONE US TO REGISTER YOUR APPLIANCE AND ACTIVATE YOUR PARTS GUARANTEE ON 08448 24 24 24  
10  
 
Troubleshooting  
It may happen that the appliance does not function properly or at all. Before calling the service centre for  
assistance, check if anything can be done. First, check to see that there are no interruptions in the gas and  
electrical supplies, and, in particular, that the gas valves for the mains are open.  
GB  
Problem  
Possible causes/Solution  
The burner does not light or the flame is not  
even around the burner.  
• The gas holes on the burner are clogged.  
• All the movable parts that make up the burner are  
mounted correctly.  
• There are draughts near the appliance.  
The flame dies in models with a safety device.  
• You pressed the knob all the way in.  
• You keep the knob pressed in long enough to activate the  
safety device.  
• The gas holes are not blocked in the area corresponding  
to the safety device.  
The burner does not remain lit when set to  
minimum.  
• The gas holes are not blocked.  
• There are no draughts near the appliance.  
• The minimum setting has been adjusted properly.  
The cookware is unstable.  
• The bottom of the cookware is perfectly flat.  
• The cookware is positioned correctly at the centre of the  
burner.  
• The pan support grids have been positioned correctly.  
If, despite all these checks, the hob does not function properly and the problem persists, call the nearest  
Customer Service Centre. Please have the following information handy:  
• The appliance model (Mod.).  
• The serial number (S/N).  
This information can be found on the data plate located on the appliance and/or on the packaging.  
! Never use unauthorised technicians and never accept replacement parts which are not original.  
PLEASE PHONE US TO REGISTER YOUR APPLIANCE AND ACTIVATE YOUR PARTS GUARANTEE ON 08448 24 24 24  
11  
 
Guarantee  
12 months Parts and Labour Guarantee  
Your appliance has the benefit of our manufacturer’s guarantee, which covers the cost of breakdown repairs for  
twelve months from the date of purchase.  
This gives you the reassurance that if, within that time, your appliance is proven to be defective because of either  
workmanship or materials, we will, at our discretion, either repair or replace the appliance at no cost to you.  
This guarantee is subject to the following conditions:  
-
The appliance has been installed and operated correctly and in accordance with our operating and  
maintenance instructions.  
-
-
-
The appliance is used only on the electricity or gas supply printed on the rating plate.  
The appliance has been used for normal domestic purposes only.  
The appliance has not been altered, serviced, maintained, dismantled, or otherwise interfered with by any  
person not authorised by us.  
-
-
-
Any repair work must be undertaken by us or our appointed agent.  
Any parts removed during repair work or any appliance that is replaced become our property.  
The appliance is used in the United Kingdom or Republic of Ireland.  
The guarantee does not cover:  
-
Damage resulting from transportation, improper use, neglect or interference or as a result of improper  
installation.  
-
Replacement of any consumable item or accessory. These included but not limited to: plugs, cables,  
batteries, light bulbs, fluorescent tubes and starters, covers and filters.  
-
Replacement of any removable parts made of glass or plastic.  
THIS GUARANTEE WILLNOTAPPLY IF THEAPPLIANCE HAS BEEN USED IN COMMERCIALOR NON-  
DOMESTIC PREMISES.  
5 Year Parts Guarantee  
Hotpoint also offers you a free 5 year parts guarantee. This additional guarantee is conditional on you registering  
your appliance with us and the parts being fitted by one of our authorised engineers. There will be a charge for our  
engineer’s time. To activate the extra parts warranty on your appliance, simply call our registration line on 08448  
24 24 24 (Republic of Ireland 01 230 0800)  
Extended Guarantees  
We offer a selection of protection plans that enable you to fully cover yourself against the expense of repair bills  
for the life of your policy. To find the ideal plan for you please call our advice line on 08448 226 226 (Republic of  
Ireland 01 230 0233).  
Free Helpdesk Service  
We have a dedicated team who can provide free advice and assistance with your appliance if you experience any  
technical difficulties within the first 90 days of ownership. Simply call our Hotpoint Service Hotline on 08448 224  
224 (Republic of Ireland 0818 313 413) for telephone assistance, or, where necessary, to arrange for an  
engineer to call.  
 
After Sales Service  
No one is better placed to care for your Hotpoint appliance during the course of its working life than us – the  
manufacturer.  
Essential Contact Information  
Hotpoint Service  
We are the largest service team in the country offering you access to 400 skilled telephone advisors and 1000  
fully qualified engineers on call to ensure you receive fast, reliable, local service.  
UK: 08448 224 224  
Republic of Ireland: 0818 313 413  
Please note: Our advisors will require the following information:  
Model number:  
Serial number:  
Parts and Accessories  
We supply a full range of genuine replacement parts as well as accessory products that protect and hygienically  
clean your appliance to keep it looking good and functioning efficiently throughout its life.  
UK: 08448 225 225  
Republic of Ireland: 0818 313 413  
Appliance Registration  
We want to give you additional benefits of Hotpoint ownership. To activate your free 5 year parts guarantee you  
must register your appliance with us.  
UK: 08448 24 24 24  
Republic of Ireland: 01 230 0800  
Indesit Company UK Ltd. Morley Way, Peterborough, PE2 9JB  
Indesit Company Unit 49 Airways Industrial Estate, Dublin 17  
Recycling and Disposal Information  
As part of Hotpoint’s continued commitment to helping the environment, Hotpoint reserves the right to use quality,  
recycled components to keep down customer costs and minimise material wastage.  
Please dispose of packaging and old appliances carefully. To minimise the risk of injury to children, remove the  
door, plug, and cut the mains cable off flush with the appliance. Dispose of these parts separately to ensure that  
the appliance can no longer be plugged into mains socket, and the door cannot be locked shut.  
 
Notes  
GB  
PLEASE PHONE US TO REGISTER YOUR APPLIANCE AND ACTIVATE YOUR PARTS GUARANTEE ON 08448 24 24 24  
14  
 
Notes  
GB  
PLEASE PHONE US TO REGISTER YOUR APPLIANCE AND ACTIVATE YOUR PARTS GUARANTEE ON 08448 24 24 24  
15  
 
Notes  
10/2011 - 195097590.00  
XEROX FABRIANO  
GB  
PLEASE PHONE US TO REGISTER YOUR APPLIANCE AND ACTIVATE YOUR PARTS GUARANTEE ON 08448 24 24 24  
16  
 

Grace MP3 Docking Station SCN300W User Manual
Graco Crib ISPP045AC User Manual
Graco Inc Paint Sprayer 222625 User Manual
Graco Microwave Oven 9120 User Manual
Harbor Freight Tools Sander 95020 User Manual
Hotpoint Washer VWSR4150BWW User Manual
HP Hewlett Packard Laptop 2000 410us User Manual
HP Hewlett Packard Switch 2000fc User Manual
Husqvarna Lawn Mower Accessory H346SL User Manual
Ice O Matic Ice Maker GEM 1256 User Manual