ICR
Institutional Commercial Remote
For Use with Hunter Controllers
Owner’s Manual and
Installation Instructions
®
ENGLISH/ESPAÑOL
MODE
OFF
ON
icr
®
Table of conTenTs.....................................................................................
Introduction................................................................................................................................................................... 1
ICR.Components............................................................................................................................................................ 2
SmartPort®.Wiring.Harness............................................................................................................................................. 4
Installing.the.SmartPort®.Wiring.Harness........................................................................................................................ 4
Wiring.the.SmartPort®.to.Hunter.Controllers................................................................................................................... 5
Typical.Installations........................................................................................................................................................ 6
Preparing.the.Transmitter.for.Use................................................................................................................................... 6
Installing.the.Transmitter.Battery.................................................................................................................................... 7
Changing.the.Run.Time................................................................................................................................................... 7
Changing.the.Transmitter.Address................................................................................................................................... 8
Changing.the.Maximum.Station.Number.......................................................................................................................... 8
Preparing.the.Receiver.for.Use........................................................................................................................................ 9
Changing.the.Receiver.Address....................................................................................................................................... 9
Activating.a.Station.with.the.ICR................................................................................................................................... 10
Maximizing.Operating.Range......................................................................................................................................... 11
Troubleshooting.Guide.................................................................................................................................................. 12
Specifications............................................................................................................................................................... 13
Tabla de conTenido...................................................................................
Presentación.del.Producto............................................................................................................................................ 15
Componentes.del.ICR................................................................................................................................................... 16
Conexión.de.Cableado.del.Programador.SmartPort®....................................................................................................... 18
Instalación.del.Arnés.de.Cableado.SmartPort................................................................................................................. 18
Conexión.de.Cableado.del.Programador.SmartPort®........................................................................................................ 19
Instalaciones.Típicas.................................................................................................................................................... 20
Preparación.del.Emisor.Antes.de.su.Uso....................................................................................................................... 20
Colocación.de.la.Pila.del.Emisor.................................................................................................................................... 21
Cambio.del.Tiempo.del.Ciclo.de.Riego........................................................................................................................... 21
Modificación.de.la.Dirección.del.Emisor........................................................................................................................ 22
Modificación.del.Número.Máximo.de.Estaciones............................................................................................................ 22
Preparación.del.Receptor.Antes.de.su.Uso.................................................................................................................... .23
Modificación.de.la.Dirección.del.Receptor..................................................................................................................... 23
Activación.de.una.Estación.por.Medio.del.Sistema.de.Mando.a.Distancia.ICR................................................................. 24
Optimización.de.la.Zona.de.Funcionamiento................................................................................................................... 25
Guía.Para.Solucionar.Problemas................................................................................................................................... 26
Datos.Técnicos............................................................................................................................................................. 27
inTroducTion ...............................................................................................
Finally.there’s.an.affordable.remote.control.system.designed.with.the.commercial.irrigation.contractor.in.mind..Hunter.is.
pleased.to.introduce.the.Institutional.Commercial.Remote.(ICR)..This.rugged.remote.design.offers.similar.functionality.as.
our.SRR.remote,.but.with.longer.range.capability..
With.the.ICR.there’s.no.need.to.walk.back.and.forth.to.the.controller.to.conduct.manual.watering.operations.when.doing.
maintenance.or.repair.work.on.your.irrigation.systems..Also,.winterization.can.be.done.quickly.and.easily.with.one.worker.
instead.of.two..
The.ICR.is.designed.to.be.rugged,.and.water.resistant..Its.large.LCD.display.and.push.button.design.makes.it.easy.to.
operate..Best.of.all,.with.an.operating.range.from.½.to.1.mile,.you’ll.be.able.to.conduct.remote.operations.on.even.the.
largest.irrigation.systems.
The.following.instructions.provide.information.on.installing,.setting.up,.and.operating.your.ICR.
ꢀ
icr componenTs.............................................................................................
B
D
A
C
9
4
®
6
2
8
MODE
OFF
ON
3
5
1
ICR
7
ꢁ
This.section.will.provide.a.brief.overview.of.some.of.the.
components.on.the.ICR..Each.item.will.be.discussed.in.
further.detail.later,.however,.this.section.can.be.helpful.in.
getting.acquainted.with.the.different.options.available.
B – Receiver
7.. Receiver Body.–.Rugged,.water.resistant.design.
8.. Addressing Button.–.Allows.for.easy.receiver.to..
transmitter.addressing..
A – Transmitter
1.. Transmitter Body.–.The.ICR.transmitter.is.designed.to.
be.dirt.tolerant.and.water.resistant..
9.. External Antennae.–.Flexible,.removable.antennae..
for.maximum.range.
C – SmartPort®
2.. LCD Display.–.Large,.easy.to.read.LCD.display..
3.. Control Buttons.–.Push.button.operation.
D – Carrying Case
4.. External Antennae.–.Flexible,.removable.rubber.for.
maximum.radio.range.
5.. Battery Compartment.–.The.ICR.is.designed.to.operate.
on.a.four.AA.alkaline.batteries..The.batteries.easily.drop.
into.a.battery.holder.
6.. Belt Clip.–.Belt.clip.provides.convenient.access.to.the.
transmitter.at.all.times.
ꢂ
smartport® Wiring Harness .......................................................................
To.utilize.the.ICR.remote.control.system,.your.controller.
To Controller
must.be.equipped.with.a.SmartPort.wiring.harness..This.
wiring.harness.provides.the.communication.port.where.the.
1/2" Thread
ICR.receiver.is.attached..The.SmartPort.can.be.connected.to.
Hunter.SRC,.Pro-C.and.ICC.controllers..A.SmartPort.wiring.
harness.is.provided.with.your.ICR.remote.system..The.
typical.SmartPort.location.is.approximately.12".below.the.
controller..The.recommended.installation.procedure.for.this.
location.would.be.as.follows:
Pre-assembled
Assembled
insTalling THe smartport Wiring Harness ........................................
1.. Install.a.½".female.threaded.“Tee”.in.the.field.wiring.
conduit.approximately.12".below.the.controller.
2.. Feed.the.red,.white,.and.blue.wires.of.the.SmartPort.
through.the.base.of.the.“Tee”.and.into.the.controller.
wiring.compartment.as.shown.in.the.following.figures..
NOTE: The harness may be installed outdoors
by bringing the conduit through an exterior
wall, then installing the appropriate fitting.
NOTE: For installations where the receiver
will be installed permanently on an outside
wall, make certain that the SmartPort is the
version with an o-ring seal.
ꢃ
Wiring THe smartport® To HunTer conTrollers ..............................
SRC Controller SmartPort Installation
Access.the.terminal.strip.area.and.attach.the.red.wire.to.the.
ICC Controller SmartPort Installation
Access.the.terminal.
left.AC.screw.slot,.attach.the.white.wire.to.the.next.AC.screw. strip.area.on.the.power.
slot.and.attach.the.blue.wire.to.the.screw.slot.marked.“R”.
module.and.attach.the.
red.wire.to.the.bottom.
most.AC.screw.slot,.
attach.the.white.wire.
to.the.upper.AC.screw.
slot.and.attach.the.blue.
wire.to.the.screw.slot.
marked.“REM”.
AC AC
R
RS
C
MV
1
2
3
4
5
6
Blue
White
Red
Blue
White
Red
Pro-C Controller
SmartPort Installation
Access.the.terminal.strip.area.on.the.
NOTE: Hunter ACC controllers are provided
with the SmartPort® Factory installed.
main.module.and.attach.the.red.wire.to.
the.bottom.most.AC.screw.slot,.attach.
the.white.wire.to.the.upper.AC.screw.
slot.and.attach.the.blue.wire.to.the.
screw.slot.marked.“REM”.
Blue
White
Red
ꢄ
Typical insTallaTions ................................................................................
Although.the.ICR.Receiver.is.water.
Indoor Installation
Outdoor Installation
(Temporary Connection
of Receiver Only)
resistant,.it.is.recommended.that.the.
SmartPort®.connector.and.Receiver.be.
mounted.indoors.if.it.is.to.be.left.per-
manently.mounted.to.the.controller.
Controller
Receiver
preparing THe TransmiTTer for use .................................................
The.ICR.remote.system.is.designed.to.work.right.out.of.
the.box..This.means.that.other.than.installing.the.battery,.
you.may.choose.to.skip.this.entire.section..However,.we.
recommend.that.you.read.it.so.that.you.can.customize.your.
ICR.to.add.functionality.and.security.to.your.system..
ꢅ
insTalling THe TransmiTTer baTTeries ............................................
The.ICR.transmitter.requires.4.AA.alkaline.batteries..To.
install.the.batteries..remove.the.two.screws.holding.the.
battery.on.the.back.of.the.transmitter..Drop.the.batteries.
into.the.battery.compartment.and.replace.the.door..Your.
transmitter.is.now.ready.to.operate.
cHanging THe run Time..............................................................................
You.have.the.ability.to.adjust.the.amount.of.time.that.a.
station.will.run.once.it.has.been.turned.on.by.your.ICR..
This.does.not.affect.the.run.time.programmed.into.your.
controller..This.adjustment.is.made.at.the.transmitter.as.
described.below.
with.the.current.Run.Time.is.displayed..(default.is.10.
minutes).The.Run.Time.will.be.blinking.at.this.point..
If.more.than.5.seconds.go.by.
without.a.button.being.pressed,.
the.Transmitter.will.revert.back.to.
displaying.the.active.station.
To change the Run Time:
3.. Use.the.
.or.
.buttons.to.
36/ꢀ5*.&
1.. If.the.unit.is.OFF.(no.display),.power.the.transmitter.by.
pressing.any.of.the.buttons.for.at.least.1.second.then.
releasing.the.button..The.transmitter.will.illuminate.and.
display.the.active.station.
change.the.Run.Time.to.any.of.
the.8.settings.ranging.from.1.to.
90.minutes..Then.do.not.touch.any.of.the.buttons.for.
5.seconds.and.the.display.will.stop.blinking.and.return.
back.to.the.active.station.
2.. Press.the.Mode.button.until.the.words.“Run.Time”.along.
ꢆ
cHanging THe TransmiTTer address ..................................................
Both.the.ICR.Transmitter.and.Receiver.have.an.“address”.
that.they.use.when.communicating..If.the.addresses.do.
not.match,.the.Receiver.will.ignore.the.transmission..Your.
ICR.comes.from.the.factory.with.both.the.transmitter.and.
Receiver.address.set.to.0..You.may.change.the.address.to.
any.value.from.0-127.for.added.security..Note.that.if.you.
change.the.Transmitter.address,.the.Receiver.must.“learn”.
the.new.address.as.described.in.the.“Preparing.the.Receiver.
for.Use”.section.
2.. Press.the.Mode.button.until.the.word.“Address”.appears.
on.the.display..The.address.will.be.blinking.at.this.point..
If.more.than.5.seconds.go.by.
without.a.button.being.pressed,.
the.Transmitter.will.revert.back.to.
displaying.the.active.station.
3.. Use.the.
.or.
.button.to.
change.the.address.to.any.value.
"%%3&44
between.0.and.127..Then.do.not.
touch.any.of.the.buttons.for.5.seconds.and.the.display.
will.stop.blinking.and.return.back.to.the.active.station.
To change the Transmitter address:
1.. If.the.unit.is.OFF.(no.display),.power.the.Transmitter.up.
by.pressing.any.of.the.buttons.for.at.least.1.second.then.
releasing.the.button..The.Transmitter.will.illuminate.the.
active.station.
cHanging THe maximum number of sTaTions.................................
Your.ICR.Transmitter.comes.from.the.factory.with.the.
maximum.number.of.stations.set.to.9..This.means.that.when.
To change the Maximum Number of Stations:
1.. If.the.unit.is.OFF.(no.display),.power.the.Transmitter.up.
you.use.the.
.or.
.buttons.to.change.the.station,.you.
by.pressing.any.of.the.buttons.for.at.least.1.second.then.
releasing.the.button..The.Transmitter.will.illuminate.the.
active.station.
may.change.it.to.any.number.between.1.and.9..However,.if.
you.have.controllers.with.more.than.9.stations.you.will.want.
to.increase.the.maximum.number.of.stations.
ꢇ
2.. Press.the.Mode.button.until.the.
word.“Max.Station”.appears.
on.the.display..The.maximum.
number.of.stations.will.be..
blinking.at.this.point.
provides.the.user.with.the.ability.to.operate.programs..
(A,.B,.C).
ACC/ACC Decoder Controllers
Selecting.the.maximum.station.number.240.allows.the.user.
to.operate.up.to.240.stations.and.18.programs.(programs.
are.displayed.with.a.P.and.program.number.ex:.P5).
."9ꢀ45"5*0/
3.. Use.the.
.or.
.button.
to.increase.or.decrease.the.
maximum.number.of.stations..Then.do.not.touch.any.
of.the.buttons.for.5.seconds.and.the.display.will.stop.
blinking.and.return.back.to.the.active.station.
NOTE: When the ICR transmitter is set in
the ACC mode (240 stations), the ICR will
only communicate with ACC controllers. To
operate other Hunter controllers (SRC, Pro-C,
and ICC) with your remote, the transmitter
max stations needs to be set to a number from
1 to 48 stations.
The.ICR.is.designed.to.operate.with.two.groups.of.Hunter.
controllers:
SRC/Pro-C/ICC Controllers
The.maximum.number.of.stations.from.1.to.48..The.ICR.also.
preparing THe receiver for use............................................................
As.stated.earlier,.your.ICR.is.designed.to.work.right.out.of.
the.box..If.you.have.decided.to.change.your.Transmitter.
Changing the Receiver Address
1.. Hold.down.the.single.button.on.the.face.of.the.
address.as.described.in.the.previous.section,.you.must.allow.
Receiver.while.you.are.plugging.it.into.an.active.
the.Receiver.to.“learn”.this.new.address..Once.learned,.the.
only.way.to.remove.the.address.from.the.Receiver.memory.
is.to.learn.a.different.address..This.can.be.done.by.following.
the.simple.steps.outlined.below.
SmartPort®.wiring.harness.(one.connected.to.a.
powered.controller)..When.this.is.done.the..
Receiver.will.beep.4.times.
ꢈ
2.. After.the.Receiver.starts.to.beep,.release.the.button.
The.ICR.system.will.allow.you.to.remotely.turn.on.and.off.
any.station.on.your.Hunter.controller.with.the.press.of.a.
button..Once.on,.the.station.will.run.for.the.run.time.you.
have.designated.in.the.ICR.transmitter.
3.. Press.either.the.“ON”.or.“OFF”.button.on.your.transmit-
ter.
4.. The.Receiver.will.beep.4.additional.times.indicating.
that.it.has.learned.the.new.Transmitter.address.and.will.
respond.only.to.it.from.this.point.on.
acTivaTing a sTaTion WiTH THe icr remoTe sysTem ......................
and.will.flash.for.about.4.seconds.indicating.that.it.is.
To remotely activate a station or program:
sending.the.command.to.the.Receiver..If.you.are.near.the.
1.. Plug.your.Receiver.into.an.active.SmartPort®.wiring.
Receiver,.you.will.hear.it.beep.2.times,.indicating.that.it.
harness.(one.attached.to.a.powered.controller).and.wait.
has.received.the.command.
for.2.beeps.indicating.the.Receiver.is.ready..
5.. Press.the.“OFF”.button.at.any.time.to.turn.off.the.station.
2.. If.your.Transmitter.is.not.on.(no.display),.press.any.
or.program..The.display.will.again.read.“TRANSMIT”.and.
button.for.at.least.1.second.and.release..The.Transmitter.
flash,.and.the.Receiver.will.again.beep.twice..The.ICR.
will.display.the.active.station.
is.designed.to.turn.one.station.on.at.a.time..Therefore,.
turning.a.station.on.while.another.is.already.on.will.
cause.the.first.station.to.turn.off.
3.. Use.the.
.or.
.buttons.to.display.the.station.or.
program.(A,B,.or.C).you.would.
like.to.start.
6.. If.one.of.the.programs.(A,B,.C.or.P1.through.P18).
is.selected,.all.stations.in.the.selected.program.will.
run.sequentially.for.the.run.time.programmed.in.the.
controller.
4.. Momentarily.press.the.“ON”.
button.to.start.the.station.or.
program..The.Transmitter.will.
display.the.word.“TRANSMIT”.
45"5*0/
ꢀ0
NOTE: The ICR remote can activate any station
on the controller whether the controller dial
is in the “System Off”, “Run” or “Run/Bypass
Sensor” modes. If a sensor device has been
wired to the controller, the ICR will not
override the sensor for manual operation.
maximizing operaTing range .................................................................
The.ICR.is.designed.as.an.extended.range.remote.that.
should.meet.the.range.requirements.for.even.the.largest.
irrigation.systems..The.maximum.range.of.transmission.will.
vary.from.approximately.½.mile.to.2.miles.depending.upon.
the.site.terrain.and.the.location.of.the.Receiver.
3.. For.maximum.range.in.all.directions.from.the.Receiver,.
the.Receiver.antennae.should.be.pointed.straight.up.
(vertically)..If.the.Receiver.is.mounted.with.its.antennae.
oriented.horizontally,.reception.will.be.very.good.if.the.
Transmitter.is.on.either.side.of.the.antennae,.but.poor.if.
it.is.facing.the.end.of.the.antennae.
Listed below are a few steps to assure that you are
getting the maximum range possible:
4.. When.operating.the.Transmitter,.hold.the.Transmitter.as.
vertical.as.possible.and.turn.and.face.the.direction.of.the.
Receiver.even.though.it.may.be.a.long.way.away.
1.. Do.not.install.the.SmartPort®.wiring.harness.(that.the.
Receiver.connects.to).near.large.sources.of.metal.such.
as.power.meters,.water.pipes,.and.metal.siding.
2.. Do.not.install.the.SmartPort.wiring.harness.in.a.
basement.or.underground.location.
ꢀꢀ
TroublesHooTing guide .............................................................................
PROBLEM
CAUSES
SOLUTIONS
Transmitter.is.blank.
Transmitter.is.Off..
Press.any.button.for.1.second..
.
.
Battery.is.dead.
Replace.battery.
Can’t.access.all.the.desired.stations. Maximum.station.number.is..
See.“Setting.the.Maximum.Station.stations.Number”
on.the.transmitter.
set.wrong.
Receiver.doesn’t.beep.two.times.
SmartPort.is.not.connected.properly.. Recheck.the.SmartPort.installation..
after.plugging.it.into.the.SmartPort®.
.
.
Controller.has.no.power.
Check.controller.power.
Receiver.beeps.twice.after.plugging. Receiver.and.Transmitter.addresses. Relearn.address.at.Receiver.
it.in,.but.won’t.respond.to.the.
transmitter.
don’t.match.
Transmitter.display.stays.on.
Transmitter.will.turn.off.
automatically.
Wait.approximately.2.minutes.without.pressing.any.
buttons..Transmitter.will.“fall.asleep.”
ꢀꢁ
specificaTions ................................................................................................
Operating Specifications
•. Address.Range:.0-127
Dimensions
Transmitter.(w/o.antennae):. Height:.6.5".
.
.
Width:.3.25".
Depth:.1.25"
•. Maximum.stations.supported:.240
•. Run.Time:.8.settings.from.1.to.30.minutes
•. Range:.up.to.2.miles.depending.upon.time.terrain
Receiver.(w/o.antennae):.
Height:.6.25".
Width:.3".
Depth:.1.25"
.
.
. .
. .
Electrical Specifications
•. Power.Source.Transmitter:.4.AA.alkaline.batteries
•. Power.Source.Receiver:.24VAC,.0.050.amps
•. System.Operating.Frequency:.27MHz.band
Default Settings
Address.=.0.(may.be.varied.from.0-127)
Number.of.Stations.=.9.(may.be.varied.from.1-48)
Run.Time:.10.minutes
ꢀꢂ
presenTación del producTo ....................................................................
Por.fin.hay.un.sistema.de.mando.a.distancia.fiable.y.accesible,.diseñado.teniendo.en.mente.las.necesidades.del.contratista.
de.la.industria.de.riego.comercial..La.sociedad.Hunter.está.satisfecha.del.lanzamiento.del.ICR,.un.sistema.de.mando.a.
distancia..Su.diseño.de.alta.resistencia.le.permite.funcionabilidad.similar.al.sistema.de.mando.tipo.SRR,.pero.con.una.
capacidad.de.mayor.distancia.
Con.el.ICR.no.existe.la.necesidad.de.caminar.de.ida.y.regreso.al.programador.para.llevar.a.cabo.operaciones.de.riego.cuando.
esté.haciendo.labores.de.mantenimiento.o.reparación.de.su.sistema.de.riego..Asimismo,.las.actividades.de.preparación.para.
el.invierno.pueden.implementarse.rápida.y.fácilmente.con.un.trabajador.en.lugar.de.dos.
El.ICR.está.diseñado.para.ser.de.alta.dureza.e.impermeable..Su.gran.pantalla.LCD.y.su.diseño.de.teclas.de.presión.lo.hacen.
fácil.de.operar..Lo.mejor.de.todo.es.que,.con.un.rango.de.operación.de.½.hasta.2.millas,.dependiendo.del.terreno,.usted.
podrá.ejecutar.operación.con.control.de.mando,.aún.en.los.sistemas.de.riego.más.extensos.
Las.siguientes.indicaciones.le.proporcionarán.la.información.necesaria.para.instalar,.modificar.y.operar.su.sistema. .
operativo.ICR.
ꢀꢄ
componenTes del icr..................................................................................
B
D
A
C
9
4
®
6
2
8
MODE
OFF
ON
3
5
1
ICR
7
ꢀꢅ
Esta.sección.le.proporcionará.un.breve.resumen.ejecutivo.
respecto.a.los.componentes.del.ICR..Cada.componente.será.
comentado.con.mayor.detalle.posteriormente,.asimismo,.
la.presente.sección.le.será.útil.para.familiarizarse.con.las.
diferentes.opciones.disponibles.del.producto.
B – Receptor
7.. Cuerpo del Receptor.–.De.alta.resistencia,.con.diseño.
impermeable.
8.. Botón de Acceso.–.Le.permite.un.fácil.acceso.al.receptor.
para.comunicarse.con.el.emisor.
A – Emisor
9.. Antenas Externas.–.Flexibles,.desmontables.para.un.
radio.de.acción.óptimo.
1.. Cuerpo del Emisor.–.El.Emisor.ICR.está.diseñado.para.
soportar.la.suciedad.y.es.impermeable.
C – SmartPort®
D – Caja
2.. Pantalla tipo LCD.–.Grande,.fácil.de.leer
3.. Tecleado de Mando a Distancia de Presión.–.Fácil.de.
operar.
4.. Antenas Externas.–.Flexibles,.de.goma.desmontable.
para.un.radio.de.acción.óptimo.
5.. Compartimiento de las Pilas.–.El.diseño.ICR.es.fácil.de.
operar.mediante.cuatro.pilas.alcalinas.
6.. Porta- Cinturón.–.Le.proporciona,.en.todo.momento,.un.
conveniente.acceso.al.emisor.
ꢀꢆ
conexión de cableado del programador smartport®....................
A.fin.de.poder.utilizar.el.sistema.de.mando.a.distancia.ICR,.
su.programador.Hunter.está.equipado.con.un.arnés.de.
Al Programador
cableado.SmartPort..Dicho.cableado.de.arnés.le.proporciona.
1/2" Rosca
una.comunicación.al.puerto.a.donde.se.conecta.el.receptor.
ICR..El.SmartPort.puede.conectarse.a.los.programadores.
SRC,.Pro-C.y.al.programador.ICC..Para.su.conveniencia,.
su.sistema.de.mando.a.distancia.ICR.incluye.un.arnés.de.
cableado.tipo.SmartPort..La.localización.típica.del.SmartPort.
es.de.12".abajo.del.programador..El.procedimiento.que.se.
recomienda.para.la.instalación.respectiva.es.como.sigue:
Pre-ensamblado
Ensamblado
insTalación del arnés de cableado smartport ................................
1.. Instale.un.adaptador.de.“T”.de.rosca.hembra.de.½".en.el.
compartimiento.del.cableado.aproximadamente.12".abajo.
del.programador.
2.. Pase.los.cables.rojo,.blanco.y.azul.del.SmartPort.por.
la.base.de.la.“T”.hacia.el.compartimiento.del.cableado.
como.se.indica.en.la.ilustración.
NOTA: El arnés puede en el exterior
estableciendo un conducto a través de la
pared externa, y posteriormente, llevar a
cabo la instalación adecuada).
ꢀꢇ
conexión de cableado del programador smartport®....................
Instalación SmartPort del Programador SRC
Con.acceso.al.compartimiento.de.cableado,.conecte.el.cable.
rojo.al.primer.borneo.marcado.AC,.el.blanco.al.borneo..
sugundo.marcado.AC.y.el.azul.al.borneo.R.
Instalación SmartPort del Programador ICC
Con.acceso.al.
compartimiento.de.
cableado,.conecte.el.
cable.rojo.al.borneo.
bajo.marcado.AC,.
el.blanco.al.borneo.
superior.marcado.AC.y.
el.azul.al.borneo.REM.
AC AC
R
RS
C
MV
1
2
3
4
5
6
Azul
Blanco
Rojo
Azul
Blanco
Rojo
Instalación SmartPort del
Programador Pro-C
Con.acceso.al.compartimiento.de.
cableado,.conecte.el.cable.rojo.al.
borneo.bajo.marcado.AC1,.el.blanco.
al.borneo.superior.marcado.AC2.y.el.
azul.al.borneo.REM.
NOTA: Los programadores Hunter ACC están
provistos de un SmartPort instalado de
fábrica.
Azul
Blanco
Rojo
ꢀꢈ
insTalaciones Típicas..............................................................................
Aunque.el.Receptor.ICR.es.impermeable,.
Instalación Interior
Instalación Exteriór
(Conexion Temporal
Únicamente del Receptor)
se.recomienda.que,.el.conector.
SmartPort®.y.su.Receptor.sean.montados.
bajo.techo,.si.es.que.se.va.a.dejar.
montado.al.programador.respectivo.en.
forma.permanente.
Programador
Receptor
preparación del emisor anTes de su uso......................................
El.sistema.de.mando.a.distancia.ICR.está.diseñado.
para.funcionar.inmediatamente..Ello.significa.que,.
exceptuando.la.colocación.de.las.pilas,.se.pueden.
ignorar.completamente,.las.instrucciones.que.siguen..
Recomendamos,.sin.embargo,.se.lean.para.personalizar.su.
ICR.y.agregar.la.funcionabilidad.y.seguridad.de.su.sistema.
ꢁ0
colocación de la pila del emisor ......................................................
Su.emisor.ICR.funciona.con.cuatro.pilas.alcalinas.de.clase.
AA..Para.instalar.las.pilas,.desplace.los.dos.tornillos.que.
sujetan.el.compartimiento.posterior.del.emisor..Introduzca.
las.pilas.en.dicho.compartimiento.e.instale.nuevamente.la.
tapa.posterior..Concluyendo.lo.anterior,.su.emisor.está.listo.
para.operar.
cambio del Tiempo del ciclo de riego..............................................
2.. Presione.la.tecla.“Mode”,.hasta.
que.aparezcan.las.palabras.“Run.
Time”..(La.duración.de.falla.es.de.
10.segundos)..A.continuación.la.
pantalla.está.intermitente..Seña-
lamos.que,.si.se.esperan.más.de.
5.segundos.sin.solicitar.ninguna.
Una.vez.que.el.ICR.haya.sido.activado,.usted.cuenta.con.
la.habilidad.de.ajustar.el.ciclo.de.riego.que.desea.en.una.
estación.determinada..Lo.anterior,.no.afecta.el.ciclo.de.
riego.que.haya.programado.en.su.programador..Dicho.
ajuste.se.lleva.a.cabo.con.el.emisor.según.se.indica.a.
continuación.
36/ꢀ5*.&
Cambios al Tiempos de Riego
tecla,.el.emisor.visualiza.de.nuevo.la.estación.activa.
1.. Si.el.emisor.no.está.alimentado.OFF.(ausencia.en.
pantalla),.colocarlo.bajo.tensión.pulsando.cualquier.
tecla.durante.al.menos.1.segundo,.entonces,.suelte.la.
tecla..El.emisor.iluminará.la.pantalla.y.se.activará.la.
estación.correspondiente.
3.. Utilizar.las.teclas. .y. .para.seleccionar.uno.de.
los.8.ajustes.de.la.duración.del.riego.que.van.de.1.a.
90.minutos..No.pulsar.ninguna.tecla.durante.al.menos.
5.segundos,.la.pantalla.deja.de.estar.intermitente.y.
vuelve.a.la.indicación.de.la.estación.activa.
ꢁꢀ
modificación de la dirección del emisor......................................
El.emisor.y.el.receptor.ICR.poseen.una.“dirección”.que.
utilizan.para.comunicarse.entre.sí..Cuando.ambas.direc-
ciones.no.corresponden,.el.receptor.ignora.la.transmisión..
A.la.salida.de.fábrica,.las.dos.direcciones.del.sistema.de.
mando.a.distancia.ICR.están.programadas.a.0..Puede.dar.
a.la.dirección.un.valor.comprendido.entre.0.y.127.para.
aumentar.la.seguridad.del.sistema..Señalamos.que.cuando.
se.modifique.la.dirección.del.emisor,.el.receptor.tendrá.que.
“aprender”.la.nueva.dirección,.como.se.especifica.en.el.
capítulo.“Preparación.del.Receptor.Antes.de.Utilizarlo”.
2.. Presione.la.tecla.“Mode”,.hasta.que.aparezcan.las.
palabras.“Run.Time”,.junto.con..la.duración.del.ciclo.
de.riego.actual..(La.duración.
de.falla.es.de.10.segundos)..A.
continuación.la.pantalla.está.
intermitente..Señalamos.que,.si.
se.esperan.más.de.5.segundos.
sin.solicitar.ninguna.tecla,.el.
"%%3&44
emisor.visualiza.de.nuevo.la.
estación.activa..
3.. Utilizar.las.teclas.
.y.
.para.modificar.cualquier.
Para Modificar la Dirección del Emisor
dirección.comprendida.entre.los.valores.0.al.127..No.
pulsar.ninguna.tecla.durante.al.menos.5.segundos,.la.
pantalla.deja.de.estar.intermitente.y.vuelve.a.la.indi-
cación.de.la.estación.activa.
1.. Si.el.emisor.se.encuentra.sin.alimentación.(pantalla.
apagada),.ponerlo.bajo.tensión.pulsando.cualquier.
tecla.durante.al.menos.1.segundo..Toda.la.pantalla.
se.enciende.durante.1.segundo.aproximadamente.y.a.
continuación.aparece.el.número.de.la.estación.activa.
modificación del número máximo de esTaciones .....................
El.emisor.ICR.está.ajustado.en.fábrica.con.un.número.
procediendo.de.la.siguientes.manera.
máximo.de.estaciones.igual.a.9..Ello.significa.que.se.
Para Modificar el Número Máximo de Estaciones
1.. Si.el.emisor.se.encuentra.sin.alimentación.OFF.(panta-
lla.apagada),.ponerlo.bajo.tensión.pulsando.cualquier.
tecla.durante.al.menos.1.segundo..El.emisor.ilumina.la..
pueden.utilizar.las.teclas.
.y.
.,.para.cambiar.
el.número.de.estaciones.entre.1.y.9..Sin.embargo,.
si.tiene.programadores.con.más.de.9.estaciones,.se.
puede.incrementar.dicho.número.máximo.de.estaciones.
ꢁꢁ
estación.activa.
Programadores SRC/Pro-C/ICC
El.máximo.número.de.estaciones.de.1.a.48..El.ICR.
proporciona.además.la.capacidad.de.poner.programas.en.
funcionamiento.(A,.B,.C).
2.. Presione.la.tecla.“Mode”,.hasta.
que.aparezcan.las.palabras.
“Max..Station”.en.la.pantalla..
A.continuación.aparece.en.la.
pantalla,.en.forma.intermitente,.
el.número.máximo.de.estacio-
nes..Señalamos.que,.si.se.esperan.más.de.5.segundos.
sin.solicitar.ninguna.tecla,.el.emisor.visualiza.de.nuevo.
la.estación.activa.
Programadores ACC/ACC99D de decodificadores
."9ꢀ45"5*0/
La.selección.del.máximo.número.de.estaciones,.240,.
permite.poner.en.funcionamiento.hasta.240.estaciones.y.
18.programas.(los.programas.se.muestran.con.una.P.y.el.
número.de.programa,.ej.:.P5).
3.. Utilizar.las.teclas.
.y.
.para.incrementar.o.reducir,.
NOTA: Cuando el mando a distancia ICR
transmite en modo ACC (para 240 estaciones)
sólo podrá comunicarse con modelos
de programadores ACC. Para utilizar
programadores estánderes de Hunter (SRC,
Pro-C y ICC) se deberá utilizar el modo de
transmisión estándar (programado para
funcionar de 1 a 48 estaciones).
el.número.máximo.de.estaciones..Posteriormente,.no.
pulsar.ninguna.tecla.durante.al.menos.5.segundos,.
la.pantalla.deja.de.estar.intermitente.y.vuelve.a.la.
indicación.de.la.estación.activa.
El.ICR.está.diseñado.para.que.funcione.con.dos.grupos.de.
programadores.Hunter:
preparación del recepTor anTes de su uso ..........................
que.el.receptor.haya.aprendido.la.nueva.dirección,.la.
única.manera.de.borrarla.consistirá.en.enseñarle.otra.
actuando.de.la.manera.siguiente:.
Como.ya.hemos.señalado,.su.sistema.de.mando.a.distancia.
ICR,.está.listo.para.su.empleo..Si.ha.cambiado.la.dirección.
de.su.emisor.del.modo.anteriormente.descrito,.el.receptor.
respectivo.tiene.que.“aprender”.la.nueva.dirección..Una.vez.
ꢁꢂ
2.. Soltar.el.botón.en.cuanto.se.oiga.el.primer.bip.
3.. Pulsar.la.tecla.“ON”.o.la.tecla.“OFF”.de.su.emisor.
Modificación de la Dirección del Receptor
1.. Mantener.hundida.la.única.tecla.situada.sobre.la.cara.
delantera.del.receptor.mientras.que.se.conecta.a.un.
conjunto.de.cables.bajo.tensión.de.un.SmartPort®.(el.
programador.bajo.tensión)..Cuanto.esto.sucede,.el.
Receptor.emite.cuatro.bips.acústicos.
4.. El.Receptor.produce.4.bips.acústicos.para.indicar.que.
ha.aprendido.la.nueva.dirección.del.emisor.y.que.ya.no.
contestará.a.otra.distinta.
acTivación de una esTación por medio
del sisTema de mando a disTancia icr ...............................................
El.sistema.de.mando.a.distancia.ICR.permite.arrancar.
o.parar.cualquier.estación.de.su.programador.Hunter.
presionando.una.única.tecla..Una.vez.que.se.ha.activado.
una.estación,.la.misma.funcionará.durante.el.ciclo.de.riego.
programado.por.medio.del.emisor.ICR.
tecla.durante.al.menos.1.segundo.y.a.continuación.
aparece.el.número.de.la.estación.activa.
3.. Utilizar.las.teclas.
.y.
.para.visualizar.la.estación.o.
el.programa.(A,.B,.o.C).que.desea.activar.
4.. Pulsar.la.tecla.“ON”.para.arrancar.la.estación.o.
programa..Sobre.la.pantalla.del.emisor.aparecen.las.pal-
abras.“ON”.y.“TRANSMIT”.y.están.intermitentes.durante.
aproximadamente.4.segundos.para.indicar.que.se.ha.
transmitido.la.orden.al.receptor..El.Receptor.emite.2.bis.
acústicos.para.indicar.que.ha.recibido.la.orden.
Para Activar a distancia una estación o un programa,
hay que proceder de la manera siguiente:
1.. Conectar.su.Receptor.a.un.Smart-
Port®.activo.(el.programador.bajo.
tensión).y.espere.a.que.el.mismo.
emita.2.bips.acústicos.indicando.
que.el.Receptor.está.listo.
5.. Pulsar.la.tecla.“OFF”.en.cualquier.momento.a.fin.de.
parar.la.estación.o.programa.que.están.funcionando..
Aparecen.las.palabras.“OFF”.y.“TRANSMIT”.en.forma.
intermitente,.y.el.Receptor.emite.de.nuevo.2.bips.
45"5*0/
2.. Si.el.emisor.no.está.alimentado.
(sin.pantalla),.pulsar.cualquier.
ꢁꢃ
acústicos..El.sistema.ICR.ha.sido.diseñado.para.poner.
una.sola.estación.en.marcha.cada.vez..Por.consiguiente,.
si.se.pone.en.marcha.una.estación.cuando.ora.está.ya.
funcionando,.esta.última.se.parará.automáticamente.
NOTA: El sistema de mando a distancia ICR puede
activar cualquier estación del programador, poco
importa que el selector giratorio se encuentra en
posición PARADO, MARCHA, o ARRANQUE / SENSOR
DE DESVIACIÓN “System off”, “Run” o “Run/
Bypass Sensor”. Si se ha conectado un captador al
programador, el sistema ICR pondrá en desviación
dicho captador, para emitir un funcionamiento
manual.
6.. Si.uno.de.los.programas.(A,.B,.C.o.desde.el.P1.al.P18).
se.selecciona,.todas.las.estaciones.en.el.programa.
seleccionada.arrancan.en.forma.secuencial.por.el.ciclo.
de.riego.programado.por.el.programador.
opTimización de la zona de funcionamienTo ..........................................
La.funcionabilidad.del.ICR.está.diseñada.con.una.extensa.
capacidad.de.mando.a.distancia.para.satisfacer.los.
requerimientos.de.sistemas.de.riego.más.grandes..La.
distancia.máxima.de.la.zona.de.funcionamiento.varía.entre.
aproximadamente.una.½.y.hasta.2.millas,.dependiendo.de.
las.características.del.terreno.y.la.localización.del.receptor.
2.. No.instale.la.salida.de.cables.SmartPort.en.un.sótano.o.
en.cualquier.otro.lugar.subterráneo.
3.. Para.obtener.una.zona.de.funcionamiento.máxima.
del.Receptor.en.todas.las.direcciones,.la.antena.del.
Receptor.tiene.que.orientarse.hacia.arriba.(posición.
vertical)..Si.el.Receptor.está.instalado.con.posición.
horizontal,.la.recepción.será.muy.buena.cuando.el.
Emisor.está.colocado.a.uno.de.los.lados.de.la.antena,.
pero.será.muy.mala.cuando.el.Emisor.esté.enfrente.del.
extremo.de.la.antena.
A continuación se proporciona una lista de algunas
que se pueden adoptar para asegurar una zona de
funcionamiento más grande posible:
1.. No.instale.la.salida.de.cables.SmartPort®.(a.la.que.está.
conectada.el.receptor).cerca.de.una.masa.metálica.
importante,.como.por.ejemplo.un.contador,.una.tubería.
de.agua,.un.revestimiento.de.aluminio.
4.. Cuando.se.utiliza.el.emisor,.hay.que.mantenerlo.lo.más.
vertical.posible.y.hay.que.girarse.hacia.el.Receptor.
aunque.se.encuentre.muy.alejado.
ꢁꢄ
guía para solucionar problemas.........................................................
PROBLEMA
CAUSAS
SOLUCIONES
El.Emisor.está.en.blanco.
El.Transmisor.está.apagado..
Presione.cualquier.tecla.por.1.segundo..
.
.
La.pila.está.descargada.
Reemplace.la.pila.
No.se.pueden.accesar.todas.las.
estaciones.deseadas.el.en.Emisor.
El.número.máximo.de.estaciones.es. Vea.“Modificación.del.Número.Máximo.de.
incorrecto.
Estaciones”.
El.Receptor.no.emite.2.bips.
acústicos.cuando.se.conecta.al.
SmartPort®.
El.SmartPort.no.está.conectado.
Verifique.que.la.instalación.del.SmartPort..
correctamente..
sea.correcta..
.
.
El.programador.no.tiene.corriente.
Verifique.la.corriente.eléctrica.del.programador.
eléctrica.
El.Receptor.no.emite.2.bips.
acústicos.después.de.conectarlo.al.
SmartPort.
Las.direcciones.entre.el.emisor.y.el. Re-programe.la.dirección.del.receptor.
receptor.no.coinciden.
La.pantalla.del.Emisor.queda.
encendida.
El.emisor.se.apagará.
automáticamente.
Espere.por.aproximadamente.unos.2.minutos.sin.
presionar.ninguna.tecla..El.emisor.“se.irá.a.dormir”.
ꢁꢅ
daTos Técnicos ...............................................................................................
Especificaciones de Operación
•. Direcciones:.0-127
Dimensiones
Emisor.(sin.antena):. Altura:.16.5.cm.
.
.
Ancho:.8.26.cm.
Profundidad:.3.17.cm
•. Número.máximo.posible.de.estaciones:.240
•. Tiempos.de.Riego:.8.reglajes.de.1.a.30.minutos
•. Alcance:.hasta.2.millas.dependiendo.del.terreno
Emisor.(sin.antena):. Altura:.15.87.cm.
. .
. .
.
.
Ancho:.7.6.cm.
Profundidad:.3.17.cm
Especificaciones Eléctricas
•. Alimentación.del.emisor:.4.pilas.alcalinas.AA
•. Alimentación.del.receptor:.24VAC,..05.amperes
•. Frecuencia.de.funcionamiento.del.sistema:..
una.banda.de.27.Mhz
Reglaje por falla
•. Dirección.=.0.(puede.ajustarse.entre.0.y.127)
•. Número.de.estaciones.=.9.(puede.ajustare.entre.1.a.48).
•. Tiempos.del.ciclo.de.Riego.=.10.minutos
ꢁꢆ
fcc compliance noTice ...............................................................................
This.device.does.not.require.an.FCC.License..The.ICR.Receiver.complies.with.the.limits.of.Part.15.of.the.FCC.Rules..The.
Transmitter.complies.with.Part.95.Subpart.E.of.the.FCC.Rules..These.limits.are.designed.to.provide.reasonable.protection.
against.harmful.interference.when.this.equipment.is.operated.in.a.commercial.environment.
Este.sistema.no.requiere.de.ninguna.licencia.de.la.FCC..El.receptor.ICR.cumple.con.los.límites.especificados.por.la.Sección.
15.de.las.Reglas.correspondientes.de.la.FCC..El.emisor.cumple.con.los.estándares.definidos.en.la.parte.95,.sub-parte.
E.de.las.Reglas.de.la.FCC..Estos.límites.se.han.designado.para.proporcionar.una.protección.razonable.contra.cualquier.
interferencia.cuando.el.equipo.y.el.sistema.estén.funcionando.en.un.medio.ambiente.comercial.
Hunter Industries Incorporated • The Irrigation Innovators
1940 Diamond Street • San Marcos, California 92078
©.2007.Hunter.Industries.Incorporated
P/N.700914.
LIT-357.
4/07
|
Graco Stroller 6907 User Manual
Harbor Freight Tools Air Compressor 94734 User Manual
Harbor Freight Tools Saw 68298 User Manual
Harbor Freight Tools Welder 45689 User Manual
Hasbro Games 06618 User Manual
Hotpoint Cell Phone Accessories DC 1 14 User Manual
Husqvarna Trimmer 124L User Manual
IBM Laptop A21e User Manual
IBM Printer 130 Plus User Manual
Icom Stereo Receiver iFR6100 User Manual