Hypertec Network Card PC Card 10 100 TX User Manual

HyperNet  
PC Card 10/100 TX  
HYNEP51001  
USER GUIDE  
Information in this document is subject to change without notice.  
All rights reserved. All brand names are registered trademarks of  
their respective companies.  
 
100Mbps Ethernet networks.  
Features  
Dual-speed 10Mbps (10BASE-T) and 100Mbps (100BASE-TX) operation  
Automatic sensing and switching between 10/100Mbps operation  
Super low power consumption  
Full Duplex - Independent receive and transmit circuits allow for full duplex  
operation at both 10Mbps and 100Mbps, giving the adapter a maximum  
throughput of 200Mbps  
Platform independent - supports all PC Card, Type II compliant PCs  
Wide selection of software drivers to support all major network operating  
systems including: Windows 98, Windows 95, Windows NT, Novell NetWare  
Superior Ethernet throughput performance using Dynamic Pipelining technology  
Direct line interface - cable only - no external dangle  
Includes Direct Enablers for reduced memory requirements  
Supports both 10Mbps and 100Mbps operations with a single RJ-45 female  
connector  
Card and Socket Services support  
 
Static Electricity Warning  
Static electricity is accumulated naturally in the human body, and can be  
discharged through electrical components by touching them. This shock can  
potentially cause permanent internal damage to the component.  
When installing the adapter, please observe the following precautions:  
Discharge yourself before commencing by touching a grounded metal appliance,  
such as the metal frame of a computer - while it is tuned off, but still plugged into  
the wall socket.  
Hold the adapter or any other boards by their edges only. Never touch any  
exposed pins on the adapter.  
If possible, install the adapter as soon as you remove it from its anti-static bag,  
without putting it down. If you must put it down, place it on the anti-static bag in  
which it was packed.  
Do not place the adapter on any metal surface.  
Hardware Installation  
The HyperNet PC Card 10/100 TX hardware installation is a three step process:  
1. Insert the HyperNet adapter into the computers PCMCIA slot  
2. Connect the media coupler to the HyperNet adapter  
3. Attach the network cable  
The HyperNet PC Card 10/100 TX adapter is a Type 11 PC Card with a 68-pin  
connector, which is compatible with any Type 11 PCMCIA slot. If your computer  
has more than one slot, you may insert the adapter in any of them. The software  
will automatically determine into which slot the adapter is inserted. Gently insert  
the card into the PCMCIA slot, pushing until it sits firmly in place, care must be  
taken not to force it as the adapter is 'keyed' to fit only one way. If it does not  
register smoothly, withdraw it and check that the keyed plug on the adapter is  
correctly aligned with the keyed socket in the host PC.  
 
(For Windows 95, select the start menu)  
4. Select Run…  
5. Type A:\SETUP and select OK.  
6. Follow the Help utility's on-screen instructions for the setup process.  
DOS Installation  
Look at the README file.  
Software Included  
ODI workstation drivers for Novell NetWare, NetWare Lite, Novell DOS 7 and  
OS2  
NDIS 2.0.1 driver for Microsoft LAN Manager, Windows for Workgroups, Artisoft  
LANtastic, Banyan Vines, OS2 and others.  
NDIS 3 for Windows 98, Windows 95 and Windows NT  
Wizard utility for installation, self-test and diagnostics  
Disconnecting the HyperNet PC Card 10/100 TX  
To remove the card from the computer PCMCIA slot, activate the release switch  
located on your computer. Alternatively, you may simply disconnect the media  
coupler, and leave the HyperNet PC Card in place in the slot ready for you to use it  
next time you need it.  
To remove the media coupler from the card, gently squeeze the plastic clip  
depressors located on the coupler and separate it from the card.  
Never disconnect the HyperNet PC Card by pulling on the cable.  
If at any time during installation you experience difficulties, please contact  
Hypertec Technical Support on +44 1488 686844 (01488 686844 in the UK).  
 
Length - 3.37" (85 mm)  
Width - 2.13" (54 mm)  
Thickness - 0.197" (5 mm)  
Power Consumption:  
100BASE-TX: 260mA  
10BASE-T  
: 190mA  
Operating Temperature:  
0°-50°C  
Operating Humidity:  
0% - 90% non-condensing  
Certifications:  
FCC Part 15, Subpart B class A  
CE  
Ethernet Protocols:  
IEEE 802.3U (Fast Ethernet, 100BASE-TX)  
IEEE 802.3 (Ethernet, 10BASE-T)  
Data Transfer Rate:  
100 or 10 Mbits/sec  
Connector:  
Unshielded female RJ45 connector to be checked.  
 
This warranty applies only to the original registered end user purchaser of the  
product and does not include service to repair damage resulting from accident,  
disaster, misuse, abuse or non-Hypertec modification of the product.  
Additional components installed by the dealer or end user are not covered by this  
warranty. Apart from the above, no warranty is expressed or implied, including  
warranty of merchantability or warranty of fitness for use for a particular purpose.  
The liability of Hypertec is limited to the repair or replacement of the product with  
a functionally equivalent or better product. Hypertec is not liable for any  
accidental, general, special, exemplary or consequential damages resulting from  
any product failure, even if Hypertec has been advised of the possibility of such  
damages.  
Hypertec Limited  
Units 1-3 Station Road  
Hungerford, Berkshire RG17 0DY  
Ph:  
Fax:  
+44 (0)1488 686844  
+44 (0)1488 686845  
Web:  
Email:  
 

Hamilton Beach Oven 31160 User Manual
Harman Kardon Universal Remote HK 3490 User Manual
Hotpoint Washer 9938 User Manual
Hotpoint Washer WWEF 722 User Manual
HP Hewlett Packard Network Card J8763A User Manual
Huffy Fitness Equipment M611814 User Manual
IBM Ricoh Printer COLOR 1767 User Manual
iHome Universal Remote Rx2 User Manual
IKEA Cooktop ICR416RB01 User Manual
I O Magic Computer Drive I1000HD35 User Manual