ILY Enterprise CD Player CoolCopy 3 User Manual

CD Duplicator

CoolCopy Series

User’s Manual

CoolCopy1AL(CD-Backup)

CoolCopy 3

CoolCopy 7

4.11.6 Auto Verify ...........................................................................22

4.11.7 Auto Compare ......................................................................22

4.11.8 Auto Prescan .......................................................................22

4.11.9 Eject Disc ............................................................................22

4.11.10 Burn on The Fly ................................................................23

4.11.11 Burn Mode ........................................................................23

4.11.12 Button Sound ....................................................................23

4.11.13 Device Info ....................................................................…24

4.11.14 System Info .......................................................................24

4.11.15 Quick Erase ......................................................................25

4.11.16 Full Erase ..........................................................................25

4.12 Adv Setup...................................................................................25

4.12.1 UnderRun Protect ...............................................….............25

4.12.2 Overburn ...............................................................…...........26

4.12.3 Read Error Skip............... ..................................…..…... ...26

4.12.4 Format Hard Disk ....................................................….........26

4.12.5 Verify HDD ...............................…..................................…...26

4.12.6 Burn-in.................................................…...…........................27

4.12.7 Update Firmware..........................................................….....27

4.12.8 Compare Firmware .......................................................…....28

4.12.9 H/W Diagnostic ...............................................................…..28

4.12.10 Load Default ..................................................................….28

Chapter 5 Troubleshooting .........................................................29

Chapter 1 Introduction

1.1 Overview

People who want to create multiple copies of their CDs usually take a long time to do so. They

might not have enough CD+RW drives or they might be using their computers for some other

important tasks. The duplication process noticeably slows down a computer during the burn

process. Rather than sit at the computer for hours duplicating discs one at a time, it is much more

efficient to use a CoolCopy CD duplication system.

The Coolcopy CD Duplicator system is a standalone duplicator and does not need to be

connected to a computer. It can duplicate discs accurately and quickly. With its multi-function

LCD panel, Coolcopy CD Duplicator is easy for any user to operate. It is a cost-efficient CD-R

duplicator for audio, data, and video applications. The simple control panel is designed to provide

copy mode selection and copy operation.

1.2 Features

•

Standalone IDE to IDE CD Copy controller

2(Coolcopy1AL(CD-Backup)) / 4(Coolcopy3) / 8(Coolcopy7) / 16(Coolcopy14)

independent IDE channel

•

Self system diagnostics when power on

Supports Hard Drive image

Auto format detection

User friendly interface with message rich LCD display

Fast copies supports high speed CD-RW writing mode

Easy operation without software and training are required

Firmware upgrade via CD-ROM

1.3 Specification

Power requirement – voltage:

Current:

5VB+/- 5%

0.5A Max.

Environment -

Temperature

Operating

Storage

0˚ C to 70˚ C

-20˚ C to 85˚ C

Humidity -

15% to 90%

Models:

Length:

Width:

Coolcopy3/coolcopy7

200 mm

Dimensions -

146.2 mm

Height:

42 mm

Connectors -

40-pin internal IDE connector

Cable (Optional) - Using ATA-66 (*Cable of length do not use longer than 46cm)

CD Format -

CD-ROM (Mode1 & Mode2), CD-ROM/XA (Mode2 form1 & form2), CD-DA,

Mixed-Mode, Video CD, CD-I, Karaoke CD, Photo CD (Single & Multi-

session), CD-Extra, HFS, CD Bridge, ISO9660, CD-R, and CD-RW

Writing mode -

Auto Detect (DAO, TAO)

Supported CD-ROM Drives* - EPO, TEAC

Supported CD-RW Drives* - Plextor, TEAC, Lite-On, Asus, SONY

Chapter 2 Installation Procedure

When you receive the Coolcopy CD Duplicator, the package could be packaged in the following

ways: controller only, whole duplicator without writer installed, and a complete duplication system.

2.1 Controller only

1. Before the installation, please prepare the necessary devices as following:

•

CD-ROM drive

CD-R/RW drive

IDE case (2~10-bay chassis suggested).

Hard drive and mobile rack (IDE-bus hard drive-Option)

Switching power supply (300W suggested).

2. After the preparation as above and make sure that:

All IDE devices must be in master mode.

•

2.2 Whole duplicator without writer installed

•

Unpack the package of the duplicators.

Prepare the CD-R/RW writers according to the recommendation list. Please check with

the supplier about compatibility issues with unlisted CD-R/RW drives.

Assemble the duplicator according to your need.

•

Make sure that the voltage setting is correct.

2.3 Completed duplication system

•

Take the duplication system out of the package.

Check the entire unit to see if there are any problems.

Make sure that the voltage setting is correct.

The hard drive is optional.

Hardware Connection of CoolCopy1AL (CD-Backup) without a HDD

CoolCopy1AL (CD-Backup)

Power

CD-RW

CD-Rom

Hardware Connection with Hard Drive for Coolcopy3

Coolcopy 3

IDE 3

CD-RW

IDE 2

CD-RW

IDE 1

CD-RW

IDE 0

CD-Rom/HDD

Power

When the system connects with the hard drive, the hard drive must connect on the IDE 0 port

with the “Master” setting and the CD-ROM must set at “Slave”.

Hardware Connection without Hard Drive for Coolcopy3

Coolcopy 3

IDE 3

CD-RW

IDE 2

CD-RW

IDE 1

CD-RW

IDE 0

CD-Rom

Power

Hardware Connection with Hard Drive for Coolcopy7

Coolcopy 7

IDE 4

IDE 3

IDE 2

CD-RW

IDE 1

CD-Rom/HDD

IDE 8

IDE 7

IDE 6

IDE 5

CD-RW

Power

When the system has a hard drive connected, the hard drive must connect on IDE 0 port with

“Master” setting and the CD-ROM must set at “Slave.”

Hardware Connection without Hard Drive for Coolcopy7

Coolcopy 7

IDE 4

IDE 3

IDE 2

IDE 1

IDE 8

IDE 7

IDE 6

IDE 5

CD-RW

CD-Rom

CD-RW

Power

Chapter 3 Key Functions and Operating Instruction

1. LCD Display Panel: Display main functions and all messages.

2. Scroll up through menus or functions.

3. Scroll down through menus or functions.

4. Execute the function which you select.

5. Cancel the function which you select.

After turning the power on, the Coolcopy CD Duplicator will execute a self test for a few seconds.

After the self testing procedure runs, the LCD will show:

Coolcopy3:

Coolcopy7:

CD Duplicator

1-3 ver: 1.10B

CD Duplicator

1-7 ver: 1.10T

Initialize SDRAM.....

Detect Drives.....

1. Copy

Two main operation procedures

If you install a 3.5” hard disc, the operation procedures is as follows:

1. With hard drive installed

•

Once duplicator detects a hard disc, it will ask if you want to format or not. A 10GB hard

disc can be divided into 10 partitions.

•

Use the Select Source to set the hard drive as the target source.

Then select which partition to store the data in function 9 “Image.”

If there is no data stored in partition, insert a source CD into CD-ROM and use function 9-

01 Load to transmit data from CD into selected partition by pressing ENT. Different data

can be stored in different partitions.

•

Switch to the Copy function by pressing the arrow button. Insert blank CD-R or CDRW

discs into the CD writers. Press “ENT” button to start copying.

•

When a Copy completes, the passed (correctly copied) CD discs will be ejected

automatically. The default is to eject automatically, but this can be changed.

Failed discs will remain in writers. The default setting is keeping failed discs in the writers,

but this can be changed. Press the buttons on the drivers to take the failed CDs.

During operation do not press any button, interruption will harm the device. CDs will be

damaged.

2. Without a hard drive installed

If you don’t install a 3.5” hard disc, the operation procedures will be as follows:

•

Insert the master disc to CD-ROM.

Switch to the Copy function by pressing arrow button. Insert blank CD-R or CDRW disc

into all the CD writers. Press “ENT” button to start.

•

When Copy completes, the passed CDs will eject automatically. The default is to eject

automatically, but this can be changed.

•

Failed CDs will remain in the writers. The default setting is that failed CDs stay in the

writers, but you can change the setting. You need to press the “eject” buttons on the

writers to take the failed CDs.

ATA-66 Cable Layout:

Please identify two different kinds of cable before the hardware installation.

Chapter 4 Function

4.1 Copy

Use this function to copy data from a source CD directly onto blank CD discs. Before copying

make sure that the source CD is insertd into CD-ROM. If you have a HDD, make sure there is

data in your HDD partition. If you are not sure about the success of your duplication job, you can

use function 2, Test, to simulate the copying process first.

Select function 1. Put a source CD into CD-ROM and blank CD disks into CD writers. CD

rewriteable discs containing old data are usable, too.

Copying-24X 0%

650.0MB 74:00

LCD will show the process of copying

information as follows:

3. Test & Copy

OK: 03

When copying is completed, the LCD will display as

1. Copy

OK: 03

the following information:

Discs correctly copied will be ejected automatically

and failed ones will remain in the writers.

4.2 Test

Function 2 Test will simulate the copying process. When the simulation completes, the discs will

remain blank.

Press “ENT” button to start the disc simulation

or press “ESC” to exit.

2. Test

If you use CD rewriteable discs that contains data, the old

Data will be quickly erased before before simulation begins:

LCD will show the following testing

Testing-24X 0%

Information:

650.0MB 74:00

When the process is finished, the LCD will

show the following message:

2. Test

OK: 03

Stopping the test halfway does not affect the CD discs. However, if the CD rewriteable discs

contain important data, the information might be erased.

4.3 Test&Copy

Function 3 Test & Copy is to test first and then actually copy.

Select Function 3. Put a source CD into CD-ROM

3.Test & Copy

And blank CD discs into writers.

Press ENT to start simulation. LCD will show the

Information as follows:

Testing-24X 0%

650

0MB 74

After the tests finishes, actual copying will begin

as follows:

Copying-24X 0%

650.0MB 74:00

When the entire process finishes, the LCD will

show the information as follows:

4. Test & Copy

OK: 03

4.4 Verify

Function 4 Verify is to examine if the target CDs can be read correctly after copying.

Press “ENT” button to verify. LCD will shows as

follows:

4. Verify

LCD will show verification information as

follows:

Verify--24X 0%

650.0MB 74:00

When the verification process is finished, the LCD

will display the result as follows:

4. Verify

OK: 03

4.5 Compare

Function 5 Compare is to make a comparison between the source and the target CDs after

copying.

Select Function 5. Put the source CD into CD-ROM

and the target CDs into CD writers.

5. Compare

Press ENT to compare. LCD will show the

comparison information as follows:

Compare-24X 0%

650.0MB 74:00

When comparison completes, LCD will show

as follows:

Compare OK: 3

Fail: 0 Diff: 0

Press “ENT” button to see the details of

source 1. If comparison is identical, LCD

will show the message as follows:

Src: 01 CD-ROM

Total: 650.0MB

If the compare result is identical, the LCD will

show as follows:

Src: 02 CD-RW

Identical

If comparison fails, LCD will show failure.

Compare OK: 2

Fail: 1 Diff: 0

Src: 01 CD-ROM

Total: 0 Bytes

Press “ENT” button to see comparison

information.

If the comparison fails, the LCD will show

failure. By pressing ENT twice, LCD will show

the contents of source 1 and those of source 2

do not match as follows:

Src: 02 CD-RW

TOC not match

4.6 Prescan

Use the prescan function to scan if the source CD can be read correctly and also to test the

reading speed.

Select function 6. Put the source CD

into CD-ROM.

6. Prescan

Press ENT to prescan, LCD will show the

scanning information as follows:

Scaning-24X 0%

650.0MB 74:00

If the master of the disc can read correctly,

the source CD has no problems. LCD

will show the following:

PreScan OK!

PreScan Fail!

If the master disc cannot be read correctly,

the LCD will show the message as follows:

4.7 Disc Info

Function 7, Disc Info, shows the basic information of the source CD.

Select Function 7. Insert source CD into CD-ROM.

7. Disc Info

Press the “ENT” button to show the disc information.

The LCD will show the total sessions and

tracks on the master disc.

Total 02 Sessions

Total 10 Tracks

Press the “ENT” button again, the LCD will show

the total time and capacity on the master disc

Total: 74:00

Total: 650 MB

Press the “ENT” button again and use arrow button

to select the session, LCD will show the

information contained in the session.

Session 01

Track 01 - 09

Press the “ENT” button again and use arrow button

to select the track. The LCD will then show what

information is contained on the track.

Track 01

AUDIO 03:54

4.8 Select Source

Function 8 Select Source will let you select the data on CD-ROM, CD writers or HDD as the

source from which you intend to copy.

8. Select Source

Select function 8.

Press ENT and then use arrow button to select the

source.

Src: CD-ROM

01 IDE0 Slave

After selecting source, press ENT and LCD will

show the following:

CD-ROM selected!

Note: Suppose you select HDD as the source and try to copy from one of its partitions, but the

partition contains no data. An error message will then appear on your LCD. From here, you can

switch to another partition that contains no data or use function 9 Image to load the data into the

chosen partition first.

4.9 Image

Function 9, Image, is only valid when you have installed a hard drive.

Select function 9. Press ENT.

9. Image

4.9.1 Load

Insert the master CD disc into the CD-ROM or any one of the CD writers, the duplicator

will detect and analyze the master CD.

Here the Load function will allow you to load data

from CD-ROM or any CD writer into the current

partition of the hard disc. P:A means Partition A.

9-01.Image P: A

Load

Press ENT to load. LCD will then show the loading

information.

Load- A -24X 0%

650.0MB 74:00

When the image has successfully loaded, the LCD

will show the following:

Image load OK

If there is an image file existing in current partition,

the system will ask whether you want to overwrite.

Use arrow button to make a “Yes” or “No” selection.

Image Exists

Overwrite?Yes

4.9.2 Delete Image

If you want to empty an image file stored in a particular partition, you can use the function Delete

Image to do so.

9-02. Image P: A

Delete Image

Select function by pressing arrow.

Delete Image in

Partition A?Yes

The system will ask if you are sure you want to delete.

Use arrow button to make “Yes” or “No” selection.

When the image is successfully deleted from the

hard drive, the LCD will show as follows:

Partition A:

Image is deleted

4.9.3 Image Info

This function shows the basic information of an image file stored in a particular partition.

Press ENT to show the disc information.

9-03.Image P: A

Image Info

The LCD will show the total sessions and tracks

in the partition.

Total 01 Sessions

Total 01 Tracks

Press ENT again. The LCD will show

the total time and capacity in the hard drive of

partition.

Total: 74:00

Total

650 MB

Press ENT again and use arrow button

to select the session. LCD will show the information in

the session.

Session 01

Track 01 - 01

Press ENT again and use arrow button

to select the track. LCD will show track

information.

Track 01

DATA 650.0MB

4.9.4 Compare Image

Use this function to compare the contents of the source CD and those of the image file in the

partition. First select the function by pressing the arrow.

9-04. Image P: A

Compare Image

Press ENT and LCD will show the comparison

information as follows:

LCD will show the following screen:

Comp-A-24X 0%

650.0MB 74:00

When the process is finished, the LCD will display

the following message:

Compare OK: 1

Fail

0 Diff

Press ENT to view the comparison details.

Src: 01 CD-ROM

Total: 650.0MB

Tgt: 00 HDD P:A

Identical

If the comparison is identical, the LCD will

show the following message:

If comparison fails, LCD will show the number of discs

failed and succeeded.

Compare OK: 0

Fail: 1 Diff: 0

Press ENT to see the comparison

information.

Src: 01 CD-ROM

Total: 0 Bytes

If the comparison fails, the LCD will show

the reason as follows:

Src: 02 CD-RW

TOC not match

4.9.5 Select Partition

This function is to select a partition in the hard disc.

Press ENT button to change the setting.

9-05.Image P: A

Select Image

After installing a hard disc, duplicator will format it automatically. Each partition occupies 1GB.

The number of partitions is dependent on the hard disc’s capacity. The partitions are

alphabetically arranged.

Use arrow button to select which partition will

be worked.

Select Working

Partition - A

When the partition is set, the LCD will show the

following:

Set Partition to

4.9.6 Select Src Drive

This function selects CD-ROM or any CD writer as the source from which you can load data into

a particular partition as an image file.

Press ENT and arrow button to select

the source.

9-06. Image P: A

Image Src Drive

Then use arrow button to select the disc as the master

Select Img Src:

source.

01 IDE0 CD-ROM

After selecting the source, press ENT.

LCD will show the source information the following info:

Load image from

Drive ID-01

4.10 Edit Track

Function 10, Edit Track, allows you to edit a collection of favorite songs from CDs. You’re able to

collect different tracks or songs on a number of CDs and merge them onto a single CD. This

process can be divided up into four parts: CD to CD, CD to HDD, Play Audio Track and Close

Session.

Press ENT and use the arrow button to select function 10.

10. Edit Track

4.10.1 CD to CD Edit

Select “CD to CD Edit” to select one or more tracks from CD-ROM and then copy onto blank CD-

R/RWs.

Press ENT to change setting.

10-01. Edit Track

CD to CD Edit

Follow the LCD to select the track that you want

to edit.

Select Track:

1/10

03:25

Press ENT to select the track. After the

track is selected, the “+” will appear beside 1/10 as shown.

Pressing ENT again will cancel the track.

Select Track:

+1/10

03:25

When the track selection is made, use arrow button

to move to the “End” manual.

Select Track:

End 1Trk03:25

Press ENT to finish the disc editing. Use arrow button

to make a selection.

End edit disc

and burn?Yes

LCD will show copying information as follows:

Copying- 24X Edit

1/10 - > 1/1

When copying ends, the LCD will show the

“Burn Complete!” message:

Burn Complete!

OK: 03

System will ask if you want to continue editing. Use the arrow

button to make a selection.

Continue edit

next Disc?Yes

If “Yes” is selected, the source disc will be

automatically ejected. Insert another disc.

Insert next disc

Follow the steps to select the track that you want

to edit. Then press ENT.

Select Track:

+2/10 04:25

When the track selection is made, use arrow button

to move to the “End” manual.

Select Track:

End 2Trk07:50

End edit disc

and burn?Yes

Press ENT button to finish the disc edition.

Use the arrow button to make a selection.

Copying- 24X Edit

1/10 - > 2/2

LCD will show copying information as follows:

The 2/2 means the second track of all tracks you have

selected. So far you have selected two tracks from two

different CDs.

Burn Complete!

OK: 03

When copying is finished, the LCD will show the

following message:

The system will ask if you want to continue editing. Use arrow

button to select “no” then press

ENT.

Continue edit

next Disc?No

The system will ask to close the disc session.

Use arrow button to make “Yes” or “No”

selection.

Close all disc’s

session? Yes

LCD will show the following screen

when you are closing the session:

Closing Session

Please wait---

4.10.2 CD to HDD

This function lets you select one or more tracks from CD-ROM and then copy the source into a

certain HDD partition.

10-02. Edit Track

CD to HDD Edit

Press ENT to enter the setting.

Follow the LCD to select the track that you want

Select Track:

to edit. Here 1/10 means the number one of 10 tracks

1/10

03:25

and 3:25 means the playing time.

Press ENT button to select the track. After the

track is selected, the “+” will appear. Pressing

ENT again will cancel the track.

Select Track:

+1/10

03:25

Select Track:

End 1Trk03:25

When track selection is made, use arrow button to

move to the “End” manual.

Press ENT to finish the disc editing. Use arrow

button to make a selection.

End edit disc

and burn?Yes

The source will be loaded to hard drive. LCD

will show the loading information as follows:

Load- P0 -24X Edit

1/10 - > 1/1

When the “Image Load” is finished, the LCD will

show the message as follows:

Image load OK

The system will ask if you want to continue editing. Use the arrow

Continue edit

next Disc?Yes

button to make “Yes” or “No” selection.

Insert next disc

If “Yes” is selected, the source disc will be automatically

ejected. Insert another disc.

Select Track:

+2/10 04:25

Follow the steps to select the track that you want

to edit. Then press ENT button.

Select Track:

End 2Trk07:50

When the track selection is made, use arrow button

to move to the “End” manual.

Press ENT button to finish disc editing. Use arrow button

to make a selection.

End edit disc

and burn?Yes

The track will be loaded as an image file onto hard drive.

LCD will the following information.

Load- P0 -24X Edit

1/10 - > 2/2

When loading is finished, the LCD will

show the message as follows:

Image load OK

System will ask you whether you want to continue editing.

Use arrow button to make a selection. Select

“No” to go next step.

Continue edit

next Disc?No

System will ask you if you want to burn from the HDD onto

CD-R/RW or move into a partition. Selecting “Burn” will

start the process.

Burn or Move to

Partition?Burn

LCD will show the copying information as follows:

Copy- P0 -24X 0%

1/2 Trk03:25

When burning is finished, the LCD will show

the message as follows:

Burn Complete !

OK: 03

Selecting “Move” will move the data from the hard

drive template to a certain partition.

Burn or Move to

partition? Move

Select the partition that the data will move into by

pressing the arrow.

Select Partition

LCD will show the moving information as follows:

Moving to P: A

When moving is finished, the LCD will show

the message as follows:

Moving to P: A

OK!

If the chosen partition contains image data,

system will ask to overwrite it. Select “No” to

Image Exists

Overwrite?Yes

keep the data image or “Yes” to overwrite it.

LCD will show the moving information as follows:

Moving to P: A

When moving is finished, the LCD will show the

message as follows:

Moving to P: A

OK!

4.10.3 Play Audio Track

This function allows your machine to be utilized as a music player. Plug in an AV terminal in the

audio port on the back of the device.

Press ESC and the arrow button to enter the play audio

10-03. Edit Track

function.

Play Audio Track

Use arrow button to select track you

are going to play.

Select Track:

1/10 03:25

Press ENT and LCD will display the playing information

as follows:

Playing Track-1

00:00 / 03:25

4.10.4 Close Session

Select “Close Session” will close the disc and restrict data writing. This function allows discs to be

read on any normal player.

Press ESC and arrow to select the function.

10-04. Edit Track

Close Session

Press ENT, the system will ask whether you want to

Close all disc’s

close. After this step, data cannot be written onto the disc.

session? Yes

Closing Session

LCD will show the message as follows:

Please wait---

When closing session is finished, the LCD will

show the following message:

Closing

Complete

4.11 Setup

This function allows you to change default settings. It is suggested that you use default setting for

optimal performance.

Press ENT button to enter the Setup function.

11. Setup

4.11.1 Language (optional)

Here are the available languages on the LCD: English, Traditional Chinese, Simplified Chinese

and Japanese.

11-01. Setup

Language

Press ENT to change the setting and ESC to

exit.

4.11.2 Burn Speed

This setting controls the burning speed of CD writers. Default setting is “Auto,”

which would use the highest available writing speed of the writer.

Press ENT to enter the setting.

11-02. Setup

Burn Speed

Use arrow button to change the burning

speed then press ENT.

Burn Speed

24X

4.11.3 Read Speed

This function lets you control the reading speeds of target CDs.

Press ENT to enter the setting.

11-03. Setup

Read Speed

Use arrow button to change the reading

speed then press ENT. The default is maximum but other

choices are 32X, 16X and 8X.

Read Speed

32X

4.11.4 Auto Start Drive

This function automatically tests or copies discs once you put the blanks discs into the writers.

Press ENT button to enter Auto Start Drive.

11-04. Setup

Auto Start

Use arrow button to change the number or

“Off” setting. Then press ENT or ESC to

go back 11-04 menu.

Auto Start

Drive

4.11.5 Start up menu

This setting lets you select any one of the functions, except Adv Setup, as the first item to appear

on the menu when you turn on your device.

11-05. Setup

Press ESC button to enter Startup Menu and

Startup Menu

ENT to enter the following figure:

Use the arrow button to select other function settings, which will

Startup Menu

1.Copy

be the first setting to appear when the device is turned on.

Then press ENT.

4.11.6 Auto Verify

This setting allows you to automatically verify if target CDs can be read after copying.

11-06. Setup

Auto Verify

Press ENT button to enter the following figure:

Use arrow button to change the “On” or “Off”

setting. Then press ENT or press ESC to go

return to 11-06 menu.

Auto Verify

Off

4.11.7 Auto Compare

This setting allows you to automatically compare the source CD and target CDs after copying.

Press ESC button and arrow to enter setting.

11-07. Setup

Auto Compare

Use arrow button to change “On” or “Off”

setting. Then press ENT to go

back 11-07 menu

Auto Compare

Off

4.11.8 Auto Prescan

This setting allows you to automatically scan if the source CD can be read correctly and also tests

the reading speed.

Press ENT button to enter Auto Prescan.

11-08. Setup

Auto Prescan

Use arrow button to change “On” or “Off” Setting.

Then press ENT or press ESC to return to 11-08 menu.

Auto Prescan

Off

4.11.9 Eject Disc

Eject disc allows three choices: Eject Good Only, Eject All Disc and Do Not Eject.

11-09. Setup

Eject Disc

Press ENT button to enter the following figure:

Use arrow button to select Eject Good Only.

Then press ENT or press ESC to return to 11-

09 menu.

Eject Disc

Eject Good

Use arrow button to select Eject All Disc,

then press ENT or press ESC to return to 11-

09 menu.

Eject Disc

Eject All Disc

Use arrow button to select Do Not Eject. Then press

ENT or press ESC to go back 11-09 menu.

Eject Disc

Do Not Eject

4.11.10 Burn on the Fly

This setting lets you controls the burning methods. When the setting is “On”, the data will copy

directly from source drive to the target drives. When the setting is “Off”, the data will load into a

partition of the hard drive first. Then, the copying will be completed.

Press ENT button to enter Burn On The Fly.

11-10. Setup

Burn On The Fly

Use arrow button to change the On or Off

Setting. Then press ENT or press ESC to return to

Burn On The Fly

The 11-10 menu.

If the system does not connect with hard drive,

the LCD will show the following message.

There is no HDD !

4.11.11 Burn Mode

This setting lets you control the burning methods. There are two modes: Disc At Once (DAO) or

Track At Once (TAO). Default setting is DAO. Some CD writers may support different writing

methods. If the method selected is not supported, duplicator will automatically switch to the other

one.

Press ENT button to enter Burn Mode.

11-11. Setup

Burn Mode

Use arrow button to change TAO or DAO

mode setting. Then press ENT or press ESC

to return to 11-11 menu.

Burn Mode

DAO

4.11.12 Button Sound

This setting allows you to control the sound when you press it.

11-12. Setup

Button Sound

Press ENT button to enter Button Sound.

Use arrow button to change On or Off

setting. Then press ENT or press ESC to return to

11-12 menu.

Button Sound

4.11.13 Device Info

This function shows the information of the CD-ROM and any CD writer you have installed.

11-13. Setup

Device Info

Press ENT button to enter the device information.

00 IDE0 Master

Use arrow button to select the device or press

ESC to go back 11-13 menu.

CD-ROMꢀꢁꢀTEAC

Press ENT button to see the device information

and ESC to return to the 11-13 menu.

CD-540E

3.0A

Use arrow button to select another device or

press ESC to return to the 11-13 menu.

01 IDE1 Master

CD-RW

ꢀꢁꢀ

PLEXTOR

Press ENT button to see the device information

and ESC to return to the 11-13 menu.

CD-R PX-W2410A

1.01

Use arrow button to select another device or

press ESC to return to the 11-13 menu.

02 IDE2 Master

CD-RW

ꢀꢁꢀ

PLEXTOR

Press ENT button to see the device information

and ESC to return to the 11-13 menu.

CD-R PX-W2410A

1.01

Use arrow button to select another device or

press ESC to return to the 11-13 menu.

03 IDE2 Master

CD-RW :ꢀPLEXTOR

Press ENT to see the information and ESC

to return to the 11-13 menu.

CD-R PX-W2410A

1.01

4.11.14 System Info

This function shows the information of the system.

Press ENT button to enter the System Info and see

the next information. Press ESC to exit.

11-14. Setup

System Info

The LCD shows

Coolcopy3 as follows:

CD Duplicator

1-3 ver: 1.10B

SST: 39SF020

2001 / 11 / 16

The LCD shows

Coolcopy7 as follows:

CD Duplicator

1-7 ver: 1.10T

WINBOND: W49F002U

2001 / 11 / 16

11-15. Setup

Quick Erase

4.11.15 Quick Erase

This function will quickly erase the data on the disc.

Press ENT button to enter the Quick Erase

and ESC to exit.

Use arrow button to confirm whether you want to erase

the data. Select the “Yes” or “No” setting. Then press

ENT or press ESC to return to 11-15 menu.

All data will be

lost, erase? Yes

LCD will show the information as follows:

Erasing disc

00:24 (Quick)

When erasing disc function is finished, the LCD will

display as follows:

Quick Erase

OK:01 Fail:00

4.11.16 Full Erase

This function is to completely erase the data on the CD rewriteable discs.

Press ENT to enter the Full Erase.

11-16. Setup

Full Erase

Use arrow button to select “Yes” or “No.”

All data will be

Then press ENT or ESC to return to 11-16 menu.

lost, erase? Yes

LCD will show the information as follows:

Erasing disc

03:24 (Full)

When finished, the LCD will show the message the

following message:

Full Erase

OK:01 Fail:00

4.12 Adv Setup

This function allows you to change the system configuration. Changes should be made only when

you are fully familiar with the function. To enter the function, please press “ESC” button for 2

seconds.

4.12.1 UnderRun Protect

This function lets you control Buffer Under Run Protection settings, such as Burn Proof,

SafeBurn, JustLink, Seamless Link, etc.

12-01. Adv Setup

Press ENT button to enter “UnderRun Protect.

UnderRun Protect

Use arrow button to change the

setting. Then press ENT or ESC to return to the

12-01 menu.

UnderRun Protect

4.12.2 Overburn

This setting lets you decide whether to copy beyond the limit of the CD or not.

12-02. Adv Setup

Overburn

Press ENT button to enter Overburn.

Use arrow button to change the

setting. Then press ENT or ESC to return to the

12-02 menu.

Overburn

4.12.3 Read Error Skip

This function allows you to neglect any error that occurs during copying. You can use this function

to copy some defective CDs.

12-03. Adv Setup

Read Error Skip

Press ENT button to enter Read Error Skip.

Use arrow button to change the

setting. Then press ENT or ESC to go

back to the 12-03 menu.

Read Error Skip

Off

4.12.4 Format Hard Disk

This function allows you to partition the hard drive.

Press ENT button to enter Format HDD.

12-04. Adv Setup

Format HDD

Use arrow button to change the

setting. Then press ENT or ESC to go

back to the 12-04 menu.

All data will be

lost, format? Yes

If the system does not connect with hard drive,

the LCD will show the message as follows:

There is no HDD!

4.12.5 Verify HDD

This function is to verify if the hard disc or any of its partitions are working well.

Press ENT to enter Verify HDD.

12-05. Adv Setup

Verify HDD

Use arrow button to change setting to Disk.

Then press ENT or ESC to go back to the 12-

05 menu.

Verify Disk or

Partition? Disk

Use arrow button to change setting to Parti.

Then, press ENT or ESC to go back to the 12-05 menu.

Verify Disk or

Partition? Parti

4.12.6 Burn-in

This function is a burn-in test, which will simulate the copying process multiple times. After each

cycle, the CDs on the CD writers will be ejected automatically and re-inserted again for

continuous testing.

Press “ENT” button to enter “Burn-in” and

12-06. Adv Setup

Burn-in

“ESC” to exit

The data will not be written on the blank

CD discs and the discs will remain blank

after the test.

Burn-in

Test

Using arrow button to change

“RunContinuous”, “1~10”, “10~100”,

“100~1000” setting. Press “ENT” or “ESC”

button to go back 12-06 menu.

Sel burn-in num:

Run Continuous

The system will repeat to erase and write

on the CD-RW discs. Only CD+RW discs can

be rewritten.

Burn-in

Erase&Copy

Using arrow button to change

Sel burn-in num:

Run Continuous

“RunContinuous”, “1~10”, “10~100”,

“100~1000” setting. Press “ENT” or “ESC”

button to go back 12-06 menu.

4.12.7 Update Firmware

This function will update your firmware to the latest version. Insert the CD disc which contains the

latest firmware data (firmware CD disc) into the CD-ROM drive and the duplicator will find the

data and update its firmware automatically. During updating, do not turn off the power of machine

because the update will not be finished until machine resets itself.

The Update Firmware function updates firmware to the latest version.

2. Unzip the firmware you have and write the file “cdxxx.bin” into the root directory of a blank

CD-R or CD-RW disc. You have to close the session of the CD. If the same CD disc still has

capacity to add more data, it can be used to store newer versions of firmware. When updating the

firmware program from the CD, only the one from last session will be used. Versions from

previous sessions will be ignored.

Select source drive to CD-ROM first! Then

12-07. Adv Setup

Update Firmware

press “ENT” button to enter “UpdateFirmware”

and “ESC” to exit.

System will search the new firmware from the

CD and the LCD will show the process as left.

When find the new firmware, just press “ENT”

button. The system will update it.

Searching F/W---

XXX/XXXXX

4.12.8 Compare Firmware

This function will help you compare your current control firmware version and the updated version

in your firmware disc that you insert into the CD-ROM.

Press “ENT” button to enter “Compare Firmware”

12-08. Adv Setup

and “ESC” to exit.

Compare Firmware

4.12.9 H/W Diagnostic

This function will detect which types of devices are connected with the control. The LCD will show

the hardware information.

Press the ENT button to enter “H/W Diagnostic”

and “ESC” to exit.

12-09. Adv Setup

H/W Diagnostic

LCD will ask user to do the button test. Following

the LCD instruction test each function button.

ꢀꢀꢀꢀꢀEnter ESC

Hold ESC to exit

After the button function testing, the system will self-test SDRAM, the hardware connecting test,

and flash test. Every testing process will be shown on the LCD. It just takes a few minutes to get

the results of hardware diagnostics. It is an easy way to know if the system works properly.

When testing is finished, the LCD will show the

“Test finished” message. Press “ESC” button to

go back 12-09 menu.

Test finished

4.12.10 Load Default

This function will reset whole previous setting back to factory’s default setting. Different settings

will cause duplicator to react differently.

12-10. Adv Setup

Press “ENT” button to enter “Load Default” and

Load Default

“ESC” to exit.

Use the arrow button to change settings. When

Load Default

Config? Yes

“Yes” is selected, the duplicator will return to

factory’s default setting.

Load Default

The LCD message will show that the setting has

been changed by with the follow message:

Chapter 5 Trouble Shooting

1. No display on LCD or the unit does not operate when power on.

•

Please check the connection of power cable and that the power

outlet is normal.

•

Turn off the power of machine, open the case of duplicator, and check if

there are any problems with the power cable.

2. LCD shows the Error message.

•

During operation like Copy, Test, Compare and Verify, you may press ESC

button to abort the operation. An Error message will be shown no the LCD.

Some CD writers will cause the duplicator to reset and you have

to re-start the power to get the duplicator to function properly.

•

A failed reading may cause an error message to show on the LCD display.

Change the master CD and try again.

During operation, if a read error, buffer under run or writing error occurs, the

LCD will show error message like: Pass xx, failed xx.

If there is no device connected and detected by duplicator during power-on,

the duplicator will show an error message on the LCD before entering the main menu.

3. CD-ROM can not read disc and shows error message.

•

Check the format of master CD or master CD itself for damage.

Use any of the CD-Writers to read the master. If it works, the CD-ROM may be

defective or not compatible with CD-ROM.

4. Buttons do not function.

•

May be still busy on task.

Button malfunction.

Faulty board.

5. Copy completed but CD-R disc is not readable / executable?

•

Use the compare function to check.

Change another CD-ROM drive to test.

6. The failure rate is high.

•

Lower the speed of the CD-Writers and try again.

Quality of blank disc is poor.

Check for latest firmware version.

Check the CD-Writer maximum writing speed. If you want to copy at 24X writing

process or higher, please copy to hard drive first and then to CD.

7. Can not boot-up or failure to upgrade firmware.

•

Contact your dealer to solve the problem. Please note that ay be charged

for this.

•

Check to see if the BIOS program is correct since customers often download

the wrong program or simply write the zipped file to CD when it should be first

unzipped before writing.

•

A failed upgrade might cause a failed boot. This can only be solver by returning

the control board to agent or factory directly. It is not necessary to return

whole system under failed upgrade.

8. Can not find the “12. Adv Setup” function.

Press “ESC” button for 2 seconds to enter the “Adv Setup”.

•

9. To cancel the duplicator working process.

•

Press “ESC” button for 2 seconds to cancel any “Copy”, “Test”, or “Verify” etc.

function while the job is in progress.

Hamilton Beach Mixer 63225 User Manual
Honeywell Thermostat 7300 User Manual
Honeywell Wok PGF3 User Manual
Hotpoint Washer AQ113DA 697 S User Manual
Hotpoint Washer WML 560 P G A K User Manual
HP Hewlett Packard Computer Monitor W1952A User Manual
iHome Clock Radio iH12 User Manual
IKEA Dishwasher IUD4000S User Manual
IKEA Indoor Furnishings AA 180830 1 User Manual
Impex Home Gym SB 240 User Manual