Ikelite Network Card iTTL User Manual

Ikelite iTTL Adapter  
Ikelite iTTL Adapter  
i n s t r u c t i o n m a n u a l  
#4301 for Specified Nikon & Fuji Digital SLR Cameras  
in Non-Ikelite Housings  
i n s t r u c t i o n m a n u a l  
#4301 for Specified Nikon & Fuji Digital SLR Cameras  
in Non-Ikelite Housings  
Delrin Pod  
Delrin Pod  
Knurled Ring  
(Rotate)  
Ikelite  
Bulkhead  
Knurled Ring  
(Rotate)  
Ikelite  
Bulkhead  
O-ring  
O-ring  
Ikelite iTTL Adapter  
Ikelite Waterproof Cap  
Ikelite iTTL Adapter  
Ikelite Waterproof Cap  
Ikelite Connector  
Ikelite Connector  
• The Ikelite iTTL Adapter is for use with Non-Ikelite housings with  
a TTL hot-shoe & Ikelite-style bulkhead.  
• The Ikelite iTTL Adapter is for use with Non-Ikelite housings with  
a TTL hot-shoe & Ikelite-style bulkhead.  
(hot-shoe must have all 5 wires connected)  
(hot-shoe must have all 5 wires connected)  
Refer to housing specifications or contact housing manufacturer for  
connector style and wiring information.  
Refer to housing specifications or contact housing manufacturer for  
connector style and wiring information.  
• The Adapter offers both TTL and Manual operation.  
Exposure compensation is not provided through the Adapter,  
but can be accessed via the camera’s menus.  
• The Adapter offers both TTL and Manual operation.  
Exposure compensation is not provided through the Adapter,  
but can be accessed via the camera’s menus.  
• The Ikelite iTTL Adapter is compatible with the following Digital  
Cameras; Nikon D-40, D-50, D-70, D-70s,  
D80, D-200 and Fuji S5 Pro.  
• The Ikelite iTTL Adapter is compatible with the following Digital  
Cameras; Nikon D-40, D-50, D-70, D-70s,  
D80, D-200 and Fuji S5 Pro.  
• The Ikelite iTTL Adapter is Not compatible with the following  
Nikon Cameras; D-100, D-1X, D-2X, D-2H.  
• The Ikelite iTTL Adapter is Not compatible with the following  
Nikon Cameras; D-100, D-1X, D-2X, D-2H.  
Connecting Adapter to houing________________________  
Connecting Adapter to houing________________________  
• Make sure all components are dry.  
• Make sure all components are dry.  
• Clean and lightly lubricate the o-ring on the male Ikelite connector.  
Check o-ring for cracks or nicks.  
• Lightly lubricate the threads on the housing bulkhead.  
• Note the positioning of the receptacles and pins. Properly align the  
end of the sync cord and insert it into the housing bulkhead.  
• Hand tighten the knurled ring on the sync cord until there is no  
in-out movement between sync cord connector and housing bulkhead.  
• Clean and lightly lubricate the o-ring on the male Ikelite connector.  
Check o-ring for cracks or nicks.  
• Lightly lubricate the threads on the housing bulkhead.  
• Note the positioning of the receptacles and pins. Properly align the  
end of the sync cord and insert it into the housing bulkhead.  
• Hand tighten the knurled ring on the sync cord until there is no  
in-out movement between sync cord connector and housing bulkhead.  
Connecting DS Substrobes __________________________  
Connecting DS Substrobes __________________________  
Use ONLY with Ikelite DS Substrobes. DS50/51, DS125, DS200  
(see strobe compatibility chart on reverse side)  
Use ONLY with Ikelite DS Substrobes. DS50/51, DS125, DS200  
(see strobe compatibility chart on reverse side)  
• Make sure all components are dry.  
• Remove the waterproof cap from the Ikelite bulkhead on the black  
delrin pod.  
• Make sure all components are dry.  
• Remove the waterproof cap from the Ikelite bulkhead on the black  
delrin pod.  
• Clean and lightly lubricate the o-ring on the male Ikelite connector.  
Check o-ring for cracks or nicks.  
• Clean and lightly lubricate the o-ring on the male Ikelite connector.  
Check o-ring for cracks or nicks.  
• Lightly lubricate the threads on the adapter bulkhead.  
• Note the positioning of the receptacles and pins. Properly align the  
end of the sync cord connector and insert it into the adapter’s bulkhead.  
• Lightly lubricate the threads on the adapter bulkhead.  
• Note the positioning of the receptacles and pins. Properly align the  
end of the sync cord connector and insert it into the adapter’s bulkhead.  
Hold the adapter’s knurled ring when tightening the sync cord.  
Hold the adapter’s knurled ring when tightening the sync cord.  
• Hand tighten the knurled ring on the sync cord until there is no  
in-out movement between sync cord connector and adapter bulkhead.  
• Hand tighten the knurled ring on the sync cord until there is no  
in-out movement between sync cord connector and adapter bulkhead.  
Single or Dual Ikelite sync cords can be attached.  
Dual strobe use requires dual sync cord.  
Two strobes cannot be operated by independent adapters.  
Single or Dual Ikelite sync cords can be attached.  
Dual strobe use requires dual sync cord.  
Two strobes cannot be operated by independent adapters.  
Instructions continued on reverse side  
Instructions continued on reverse side  
 

Graco Baby Accessories PD226470A User Manual
Graco Baby Swing PD162126B User Manual
Graco Car Seat 2791 User Manual
Graco Stroller 1774385 User Manual
Grundig Stereo System Weather AM FM Radio User Manual
Haier Flat Panel Television LE46A2280 User Manual
Hamilton Beach Coffee Grinder 840101100 User Manual
Hasbro Baby Toy 6896930000 User Manual
Heat Glo LifeStyle Indoor Fireplace 6000TRI IPI User Manual
Honeywell Home Security System 408 User Manual